TN_43_1

5.9 Centering and shuttering including strutting, propping etc. and removal of form for 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts

5.9 Centering and shuttering including strutting, propping etc. and removal of form for 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers

5.9 Centering and shuttering including strutting, propping etc. and removal of form for 5.9.19 Weather shade, chajjas, corbels etc., including edges

5.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 5.2.2 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.3 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

5.22A Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more.

6.3 Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS:2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 ( 1 cement :6 coarse sand) 6.3.1 With F.P.S. ( non- modular) bricks

6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 6.13. 1 Cement mortar 1:3 (1 cement : 3 coarse sand)

9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 9.1.2 Sal wood

9.5 Providing and fixing panelled or panelled and glazed shutters of doors, windows and celerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.( Note:- butt hinges and necessary shall be paid separately) 9.5.1 Second class teak wood 9.52.1 35 mm thick shutters

9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters ( over all area of door shutter to be measured).

9.96.1 Providing and fixing aluminium sliding door bolts, ISI marked anodised ( anodic coating not )

9.102 Providing and fixing aluminium casement stays, ISI marked, anodised ( anodic coating not )

9.97.2 Providing and fixing aluminium tower bolts, ISI marked, anodised ( anodic coating not less) 250x10 mm( Door tower Bolt)

9.97.4 Providing and fixing aluminium tower bolts, ISI marked, anodised ( anodic coating not less) 150x10 mm ( Window tower Bolt)

9.100.1 Providing and fixing aluminium handles, ISI marked, anodised ( anodic coating not less) 125 mm Door handle

9.100.2 Providing and fixing aluminium handles, ISI marked, anodised ( anodic coating not less) 100 mm Window handle

21.1.1. 2 Powder coated aluminium ( minimum thickness of powder coating 50 micron )

21.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.8 Filling the gap on between aluminium frame & adjacent RCC/ Brick/stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. 21.8.1 Upto 5 mm depth and 5 mm width

21.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

10.31 Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm , joints mitred and welded by angle iron 35x35x5 mm or 35x5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel, primer, all complete as per the direction of Engineer-in-charge.

13.2 15 mm cement plaster on rough side of single or half brick wall of mix: 13.2.1 1:4 (1 cement: 4 fine sand)

13.4 12 mm cement plaster of mix 13.4.1 1:4 ( 1 cement : 4 coarse sand )

13.16 6 mm cement palster of mix 13.16.1 1:3 ( 1 cement : 3 fine sand )

13.26 Providing and applying plster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

13.41 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: 13.41.1 New work ( two or more coats) over and including water thinnable priming coat with cement primer

13.43 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: 13:43.1 water thinnable cement primer

13.50 Applying priming coat: 13.50.1 With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

13.50.3 with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

13.48.2 Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 Itr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

13.48.3 Painting steel work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 Itr/10 sqm over an under coat of primer applied @0.80 ltr/10 sqm of approved brand and manufacture

12.45 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections,power pressed from M.S. Sheets and galvanized with zinc coating of 120 me ing of trame work made of special sections ats of size 25 mm wide x 1.6 mm thick with fla aung of 120 gms/sqm (both side inclusive) and with dash fastener 12.5 mm disCK with Hanges of 27 mm and 37mm, at 1200 mm centre to centre. one flanee fived to the cailn re stener 12.5 mm dia x 50mm long with 6mm dia bolts other flre centre, one tlange fixed to the ceiling required length with nuts & bolts of reguired ld oits, other llange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I channels 45x15x0.9 mm running at the spacing of 1200 required size and other end of angle hanger fixed with intermediate G.l. channels 45x15x0.9 mm at the spacing of 1200 mm centre to centre, to which the ceiling section mediate G.l. channels 45x1Sx0.9 mm of 26 mm each having lips of 10.5 mm at 450 the celling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges with connectine rli mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.l. intermediate channe with connecting clips made out of 2.64 mm dia x 230 mm long G. wire at ev cuiar toG.. Intermediate channel 27 mm high having flanges of 20 mm and an mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick aving manges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl nlues at 450 m centre, with 25mm long dry wall screws @ 230 mm interval includine fivt wa/partition with the help of rawl plugs at 450 mm the heln of drv wall ws 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/C, including jointing and finishine to a flush finich of tanerer and n of the board with recommended ininting , Incuing jointing and tinishing to a flush finish of tapered and square edges wien recommended Jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering, upto 150 mm on both sides of joint and two coats of primer suitable for board all as ner manlfartrer'e i m on ats Or primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all comolete as ner At specification and direction of the n us made with frame of perimeter channels suitably fixed, all complete as per drawings, speciication and direction of the Engineer in Charge but excluding the cost of painting with: 12.45.2 12.5 mm thick tapered edge gypsum moisture resistant board.

11.41A. Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 11.41A.3 Glazed vitrified tiles Matt/Antiskid finish of size 11.41A.3.2 Size of tile 600 x 1200 mm

10.16 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.3 Electric resistance or induction butt welded tubes

12.1 Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with hex cap headed self drilling/tapping stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-in- charge. ( Cost of truss/frame work shall be paid separately) 12.1.3 0.56mm Aluminium color profile with center pitch of 175 mm, depth of 46mm , top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm cover width 1050mm,.

12.4 Providing ridges or hips of width 60 cm overall width plain G.S sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 12.4.2 0.60 mm thick with zinc coating not less than 272 gm/m²

18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work- Exposed on wall 18.7.3 25 mm nominal dia Pipes

18.49 Providing and fixing C.P brass bib cock of approved quality conforming to IS:8931 18.49.1 15 mm nominal bore

17.73 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 17.73.2 450 mm long towel rail with total length of 495 mm, width 78 mm and effective height of 88 mm, weighing not less than 170 gms.

17.3 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with itings & C.1.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fitings and brackets, cuting and making good the walls and foors wherever required. 17.3.1 W.C. pan with ISI marked white solid plastic seat and lid

17.5 Providing and fixing white Vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass dlush pipe, spreaders with unions and clamps ( all in C.P. brass) with waste fitting as per IS: 2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required: 17.5.1 Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 110 mm diameter.

8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying: First layer of slurry of cement @ 0.488 ka/sam mixed with water proofing cement compound @0.253 kg/ sam. This layer will be allowed to air cure for 4 hours. Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry Providing and fixing soil, waste and vent pipes: 17.35.1 100 mm dia

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainiess steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

13.2 15 mm cement plaster on rough side of single or half brick wall of mix: 13.2.1 1:4 (1 cement: 4 fine sand)

13.4 12 mm cement plaster of mix 13.4.1 1:4 ( 1 cement : 4 coarse sand )

13.16 6 mm cement palster of mix 13.16.1 1:3 ( 1 cement : 3 fine sand )

13.26 Providing and applying plster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

13.41 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: 13.41.1 New work ( two or more coats) over and including water thinnable priming coat with cement primer

13.43 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: 13:43.1 water thinnable cement primer

Electrical Works 1.1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 1.1.3 Group C

1.10.2 Group B

1.7 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, singlecore cable in surface/ recessed medium class PVC conduit as required. 1.7.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

1.7.3. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 1.21.2 25 mm

1.24 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 1.24.1 5/6 A switch

1.24.3 15/16 A switch

1.24.4 3 pin 5/6 A socket outlet

1.24.5 6 pin 15/16 A socket outlet

1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

1.27 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc.as required. 1.27.2 1 or 2 Module (75mmX75mm)

1.27.6 12 Module ( 200mm 150mm )

1.50 Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. 1.50.2 510 mm sweep

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS: 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambienttemperature without tripping. The unit shallbe suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc. suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. 3.5 1.45 TR

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system,complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suctionand Liquid lines, all accessories as per specifications etc. as required : 5.3 12.7 mm dia (OD) ( soft drawn ) with tube thickness 1.2 mm with 19

2.3 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2.3.1 6 way , double door

For Supply and Installation of 6W LED Panel Light with 3000K warm white colour.