Comprehensive operation and maintenance, routine repairs and Special repairs of i.) Rural Piped Water Supply Scheme (PWS)- 12 Nos, ii.) Single Village piped water supply schemes (SVS)- 15 Nos, iii.) Ward level Piped Water Supply Schemes in non quality affected wards (WLS)-125 Nos based on item rates; constructed by the Public Health Engineering Department including payment to the pump operators, electricity bills for five years.

TECHNICAL BID SHEET OF GROUP 01 TENDER NIT No– 01R1/MOTIPUR(NQ)V2026-27/O&M-PHED

Name of Work Comprehensive operation and maintenance, routine repairs and Special repairs of i.) Rural Piped Water Supply Scheme (PWS)- 12 Nos, ii.) Single Village piped water supply schemes (SVS)- 15 Nos, iii.) Ward level Piped Water Supply Schemes in non quality affected wards (WLS)-125 Nos based on item rates; constructed by the Public Health Engineering Department including payment to the pump operators, electricity bills for five years. Cost of Work as per BOQ(Rs in Lakhs) 0.19999 Time of Completion in months 60 ALL COLOURED CELL TO BE FILLED ACCORDINGLY

Sanctioned Amount As per Technical Approval Date of Tender 16.03.2025

Sl No. Items Requirement Requirement Cl. No.

Name of the Contractor

Address of the Contractor

1 Bid Validity Bids shall remain valid for a period not less than 180days after the deadline date. A Bid valid for a shorter period shall be rejected by the Employer as non-responsive 180 Days 15.1 Page/17 Bid validity periods In days

2 Bid Security a)Unconditional bank guarantee from any scheduled Indian bank issued within the state in the format given (If issued from any bank outside state will be converted to any bank within the state before executing the agreement, duly pledged in favour of the Executive Engineer, PHED Division, Motipur 16.1 Page-17 Amount To be entered (Rs in Lakhs)

Bid Security Amount - (Rs. In Lakhs) 3389000 Bid Security Amount - Rs. 0

3 (i) Legal Status of Bidder. 4.3(a) Page-12

(ii) Place of Registration.

(iii) Principal place of Business

(iv) Power of attorney of signatory Bid Attached or Not 4.2(iv) Page-11

4 Total value of civil engineering construction work performed in last five years. Achieved in any one year during the last five years, a minimum annual financial turnover (in all classes of civil engineering construction works only) volume of construction work of at least the amount equal to the 50% (fifty percent) of the estimated cost of the works for which bid has been invited. The turnover will be indexed at the rate of 8% for a year. The certificates attached in support of turnover attached shall have valid Unique Document Identification Number (UDIN). 4.5A (a) Page -16

2020-21 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.47 0

2021-222 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.36 0

2022-23 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.26 0

2023-24 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.17 0

2024-25 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.08 0 0

5A Work Experience of Similar nature S(b) Satisfactorily completed as a prime contractor (or as a nominated sub contractor, where the sub contract involved execution of all main items of work described in the bid document, provided further that all other qualification criterion are satisfied) at least one similar work of value not less than the amount indicated in the appendix (Not less than 10% (Ten percent) estimated value of contract). Or Satisfactorily completed water supply scheme (Piped water supply or lift irrigation or water supply in building) at least one work of value not less than 10% (ten percent) of the estimated cost of the works for which bid has been invited. 4.5A (a,b,c) Page -16 Amount To be entered (Rs in Lakhs)

(c) Executed the minimum quantities of the following item of work as indicated in the appendix:

Description of item Units Total Quantity in BoQ Quantity required to have been executed

Maintenance of water supply schemes in water non quality affected areas. years 5 year 2.50 years 4.5A (a,b,c) Page -16

7 Bidding Capacity: More than the total Bid value of present work = A*N*3-B=Rs. ____.Where A = Maxm. Value of work executed in any one yr during last 5 yrs. N= Nos of years for completion of works. B=Value of existing commitments & ongoing works to be completed in period. Necessity of bid capacity for bidders who meet the minimum qualifying criteria is not mandatory for ward wise schemes up to Rs. 2.00 crore in Har Ghar Nal Ka Jal Nishchay Yojna. Clause- 4.7(a) above is not applicable for this category of schemes 0.800 4.7 Page- 13 0

6 Bidding Capacity: Should be more than Available Bid capacity = (A x N x 3 - B)= Rs. _____, Where A= Maximum Value of work executed in any one year during last 4 yrs. , N = Number of years prescribed for completion of the works for which bids are invited. (For contracts involving operation and maintenance; the period of completion shall be the sum of entire DB duration and half the duration of the O&M period), B= Value (updated to the price level of the year indicated in Appendix) of existing commitments and on-going works to be completed during the next 12 months 4.5A (a) Page -16 Amount To be entered (Rs in Lakhs)

7 (a) Existing commitments and ongoing works Page - 20 Amount To be entered (Rs in Lakhs)

(b) Work for which Bid already submitted Page - 20 Amount To be entered (Rs in Lakhs)

8 Availability of key items of Contractor's Equipment Type of Equipment/Maximum age No. Required Nos. Max. Age 4.5(B) (b) Page-26 Annexure-I Nos./ Max. Age

Concrete Mixer 2 5

Rotary Drilling / Reverse Rotary / DTH Rig Machine 1 5

Truck/Tractor with trailer 1 5

Hydraulic Excavator 1 5

9 5-30 Crores 4.5(B) (b) Page-34 Annexure-II Name of the Personnel and Experience in years

Project Manager B.E. Civil + 10Years Exp. (5 years as Manager in PHED works) or retired E.E. & above of PHED 1

Site Engineer B.E. Civil + 07Years Exp. (3 years as Manager in PHED works) or retired A.E. & above of PHED 2

Burveyor .B E. Civil + 03 Years Exp. orDip. Civil + 05 years Exp. 1

10 Evidence of accesses to Financial Resources Evidence of access to or availability of credit facilities (10% of estimated cost), certified by bankers (Not more than 3 months old). (Rs in Lakhs). Page 15 4.3 (g) Amount To be entered (Rs in Lakhs)

11 Proposed methodology and programme of construction. Justifying their capability of execution and completion of the work as per technical specifications within the stipulated period of completion as per milestones. (Attached or not) Page 15 4.3 (l)

12 Litigation History Information regarding any litigation, current or during the last five years, in which the Bidder is involved, the parties concerned, and disputed amount. (Attached or not) Page 15 4.3 (j)

13 Affidavit Regarding statements made in the required attachments are true and correct. Page 23 12.1 (iv)

14 Undertaking Able to invest a minimum of cost upto 25% of contract value of work. During implementation of contract. 25 % of B.O.Q.Amount Page 12 4.3 (h)

17 Character Certificate

18 Time of Completion 60 Months To be entered in months

QUALIFICATION INFORMATION

The information to be filled in by the Bidder in the following pages will be used for purposes of post qualification as provided for in Clause 4 of the Instructions to Bidders. This information will not be incorporated in the Contract.

NAME OF THE CONTRACTOR

1 For Individual Bidders

1.1 Constitution or legal status of Bidder (Attach copy)

Place of registration :

Principal place of business :

Power of attorney of signatory of Bid (Attach)

1.2 Total value of Civil Engineering construction work performed in the last five years** (in Rs. Million)

1.3.1 Work performed as prime contractor, work performed in the past as a nominated sub- contractor will also be considered provided the sub-contract involved execution of all main items of work described in the bid document, provided further that all oth

NAME OF THE CONTRACTOR

Project Name Name of the Employer* Description of work Contract No. Value of Contract (Rs. In Crore) Date of issue of work order Stipulated period of completion Actual date of completion* Remarks explaining reasons for delay & work completed)

* Attach certificate(s) from the Engineer(s)-in-Charge

** Immediately preceding the financial year in which bids are received.

 Attach certificate from Chartered Accountant.

1.3.2 Quantities of work executed as prime contractor, work performed in the past as a nominated sub-contractor will also be considered provided the sub-contract involved execution of all main items of work described in the bid document, provided further that all other qualification criteria are satisfied (in the same name and style) in the last five years.

NAME OF THE CONTRACTOR

Year Name of the work Name of the Employer* Quantity of work performed

Remarks* (indicate contract Ref)

1.4 Information on Bid Capacity (works for which bids have been submitted and works which are yet to be completed) as on the date of this bid.

(A) Existing commitments and on-going works:

NAME OF THE CONTRACTOR

Description of works Place & State Contract No. Name & Address of Employer Value of Contract (Rs Cr) Stipulated Period of Completion Value of works* remaining to be completed (Rs Cr) Anticipated date of completion

* Attach certificate(s) from the Engineer(s)-in-Charge

The item of work for which data is requested should tally with that specified in ITB clause 4.5A ©

** Immediately preceding the financial year in which bids are received.

# Delete, if prequalification has been carried out.

(B) Works for which bids already submitted :

Description of works Place & State Name & Address of Employer Estimated value of works (Rs Cr) Stipulated period of completion Date when decision is expected Remarks, if any

1.5 Availability of key items of Contractor’s Equipment essential for carrying out the Works [Ref. Clause 4.5(B)(a)]. The Bidder should list all the information requested below. Refer also to Sub Clause 4.3 (d) of the Instruction to Bidders.

NAME OF THE CONTRACTOR

Description of works Requirement Availability proposals Remarks (from whom to be purchased)

No. Capacity Owned/Leased to be procured Nos./Capacity Age/ Condition

1.6 Qualifications and experience of key personnel required for administration and execution of the Contract [Ref. Clause 4.5(B)(b)]. Attach biographical data. Refer also to Sub Clause 4.3 (e) of instructions to Bidders and Sub Clause 9.1 of the Condition

NAME OF THE CONTRACTOR

Position Name Qualification Year of Experience (General) Years of experience in the proposed position

1.7 Proposed sub-contracts and firms involved. [Refer ITB Clause 4.3(k)]

NAME OF THE CONTRACTOR

Sanction of the works Value of Sub-contract Sub-contractor (Name & Address) Experience in similar work

Attach copies of certificates on possession of valid license for executing water supply/ sanitary work/ building electrification works [Reference Clause 4.5(d) & Clause 4.5(e)]

*1.8 Financial reports for the last five years: balance sheets, profit and loss statements, auditors' reports (in case of companies/corporation), etc. List them below and attach copies.

1.9 Evidence of access to financial resources to meet the qualification requirements: cash in hand, lines of credit, etc. List them below and attach copies of support documents.

1.10 Name, address and telephone, telex and fax numbers of the Bidders' bankers who may provide references if contacted by the Employer.

1.11Information on litigation history in which the Bidder is involved.

NAME OF THE CONTRACTOR

Other Party(ies) Employer Cause of Dispute Amount involved Remarks showing Present Status

1.12 Statement of compliance under the requirements of Sub Clause 3.2 of the instructions to Bidders. (Name of Consultant engaged for project preparation is ** ........................ …………….............................)

Proposed work method and schedule. The Bidder should attach descriptions, drawings and charts as necessary to comply with the requirements of the Bidding documents. [Refer ITB Clause 4.1 & 4.3(1)]

1.15 Quality Assurance Programme

2 Additional Requirements

2.1 Bidders should provide any additional information required to fulfill the requirements of Clause 4 of the Instructions to the Bidders, if applicable.

(ii) Undertaking

*** (iii) Update of original prequalification application

*** (iv) Copy of original prequalification application

*** (v) Copy of prequalification letter

* Delete, if prequalification has been carried out.

** Fill the Name of Consultant.

*** Delete, if prequalification has not been carried out.

Check List for Submission Of Tender

Evaluation will be done as per the information provided in the document attached with tender. Bidder may disqualified, if documents are not attached properly.

Name of the Bidder

Sl. No. Checklist Items (Attach Documents in Edit Attachment Folder) Document attached

1 BIDSECURITY PHOTO COPY

2 LAST 5 YEARS ANNUAL TURN OVER

3 EXPERIENCE Of SIMILAR NATURE Of W0RKS

4 QUANTITY OF WORK OF SIMILAR NATURE EXECUTED DURING LAST 5 YEARS)

5 BALANCE VALUE OF ON GOING WORKS

6 EXISTING COMMITMENTS

7 BANKER'S CERTIFICATE FOR ACCESS OF FINACIAL RESOURCES

10 LITIGATION HISTORY

11 PLANT and MACHINARIES

12 KEY PERSONNEL

13 Registration

14 Power of Attoney

15 Legal Status Of Bidder

16 PROGRAMME Of CONSTRUCTION

17 NOC FOR DEBAR

18 LABOUR LICENCE

20 GST CERTIFICATE

21 Character Certificate

22 Any other Documens required as per NIT/ Standard Bidding Documents Required

IF YOU HAVE NOT BEEN DEBARED WRITE "NOT APPLICABLE" IN YOUR LETTER HEAD SCAN AND UPLOAD IN THE IN NOC FOR DEBAR LINK

Note:-Attachment should be self attested and should be attached as per above instruction, otherwise it may be rejected.

I, the undersigned, do hereby certify that all the statements made in the required attachments are true and correct.

Signature & Seal of the Bidder

NIT No.:-01R1/Motipur(NQ)2026-2027/O&M-PHED

NAME OF WORK- Comprehensive operation and maintenance, routine repairs and Special repairs of i.) Rural Piped Water Supply Scheme (PWS)- 12 Nos, ii.) Single Village piped water supply schemes (SVS)- 15 Nos, iii.) Ward level Piped Water Supply Schemes in non quality affected wards (WLS)-125 Nos based on item rates; constructed by the Public Health Engineering Department including payment to the pump operators, electricity bills for five years.

Date of Tender :- 15.05.2026

Estimated Cost :- 238863300.00

Earnest Money :- 3389000.00

Duration of Maintenance Period 5 Year

Cost of BOQ :- 10000.00

SI NO. PARTICULARS No. of Scheme AMOUNT

1 Comprehensive operation and maintenance, routine repairs and Special repairs of i.) Rural Piped Water Supply Scheme (PWS)- 14 Nos, ii.) Single Village piped water supply schemes (SVS)- 15 Nos, iii.) Ward level Piped Water Supply Schemes in non quality affected wards (WLS)-125 Nos based on item rates; constructed by the Public Health Engineering Department including payment to the pump operators, electricity bills for five years. (i) WLS(Non Quality):-125 (ii) PWSNon Quality) -14 (iii) SVS Non Quality)-15 . 238,863,300.00

Total Amount 238,863,300.00

Rupees Twenty Three Crore Eighty Eight Lacs Sixty Three Thousand Three Hundred Only

1 Estimated cost Rs. 238,863,300.00 (A)

2 Cost of Govt. Material :- NIL NIL (B)

3 Name of the Contractor :-

4 Address of the Contractor :-

5 I/we offer in Figures……. in words………………… % (Percentage) High on the rate for the fixed cost (Part I) for operation of the schemes. IN FIG.

6 I/we offer in Figures……. in words………………… % (Percentage) High / Less on the rate for the variable cost (Part-II) for maintenance of the schemes. IN FIG. 100

7 Average rate quoted by the bidder 0.00

Note :- 1.) Bidders has to quote rate in Percentage High/Less only. 0.6

Note :- 2.) Items/ Quantity of Work will be decided by the department on day to day / priority basis during period of maintenance.

Note :- 3.) The quoted rate for the operation part I (fixed cost) i.e. the payment to the operators and the electricity bills, the quote shall not be negative.

Note :- 4.) The electricity bills shall be paid as per actual.

Note :- 5.) The entry in row 7 shall be considered for decision of financially lowest bid.

Executive Engineer, P.H.Division, Motipur

GOVERNMENT OF BIHAR

Public Health Engineering Department

Bill of Quantity 1 (Variable Cost)

S.N. Description Quantity Unit Rate Total Amount

1A Construction of 150mm X100mmx 125m deep T/W etc. all complete and as per direction of E/I.(As per sub Estimate no.- 1) 1 Nos. Rs.294,314.73 Rs.294,314.73

1B Construction of 150 mmX90m deep drilled T/W etc. all complete and as per direction of E/I. 1 Nos. Rs.180,147.69 Rs.180,147.69

2 Constructing masonry Chamber 100x100x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for Tube Well, and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size ) , necessary excavation, foundation concrete 1:2:4(1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3coarse sand) 12 mm thick with 5% cico fnished with a floating coat of neat cement, out side plastering with cement mortar 1:4 (1 cement : 4coarse sand) 12 mm thick complete as per standard specifications & direction of E/I. (As per sub Estimate no.- 2) 1 Nos. Rs.15,314.08 Rs.15,314.08

3A Supply Installation, commissioning and testing of single phase 3 H.P submersible pump set having discharging capacity 3.35 lps at a total head of 35 meter(approx) of different capacity of KSB/ Kirloskar or equivalent make with all accessories & fittings such as 7.5KVA Stabalizer, cable, panel board etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & commissioning as per standards specifications and direction of E/I. (As per sub Estimate no.- 3a) 1 Nos. Rs.110,628.00 Rs.110,628.00

3AA Supply Installation, commissioning and testing of single phase 3 H.P submersible pump set only having discharging capacity 3.35 lps at a total head of 35 meter(approx) of different capacity of KSB/ Kirloskar or equivalent make with all accessories & fittings etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & commissioning excluding the cost of GI pipes for lowering and cables etc. as per standards specifications and direction of E/I. (As per sub Estimate no.- 3a items) 1 Nos. Rs.25,000.00 Rs.25,000.00

3B Supply Installation, commissioning and testing of single phase 2 H.P submersible pump set having discharging capacity 2.25 lps at a total head of 35 meter(approx) of different capacity of KSB/ Kirloskar or equivalent make with all accessories & fittings such as 7.5KVA Stabalizer, cable, panel board etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & commissioning as per standards specifications and direction of E/I. (As per sub Estimate no.- 3b) 1 Nos. Rs.68,220.60 Rs.68,220.60

3BB Supply Installation, commissioning and testing of single phase 2 H.P submersible pump set having discharging capacity 2.25 lps at a total head of 35 meter(approx) of different capacity of KSB/ Kirloskar or equivalent make with all accessories & fittings etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & commissioning excluding the cost of GI pipes for lowering and cables etc. as per standards specifications and direction of E/I.(As per sub Estimate no.- 3B items) 1 Nos. Rs.20,000.00 Rs.20,000.00

3C Supply Installation, commissioning and testing of three phase 5 H.P submersible pump set including light wiring, power wiring and extension of over head L.T line from nearest point of electric line up to pump room having 50 C/sec. 2900 rpm at a total head of 35 meter(approx) of different capacity of KSB/ Kirloskar or equivalent make with all accessories & fittings etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & commissioning complete set as per standards specifications and direction of E/I. (As per sub Estimate no.- 3c) 1 Nos. Rs.140,107.73 Rs.140,107.73

3CC Supply Installation, commissioning and testing of three phase 5 H.P submersible pump set only having 50 C/sec. 2900 rpm at a total head of 35 meter(approx) of different capacity of KSB/ Kirloskar or equivalent make with all accessories & fittings etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & commissioning excluding the cost of GI pipes for lowering and cables etc. as per standards specifications and direction of E/I. 1 Nos. Rs.40,000.00 Rs.40,000.00

4a Providing & Fixing BIS approved 3 HP submersible motar starter all complete as per direction of engineer in charge. (As per sub Estimate no.- 4a) 1 Nos. Rs.5,478.72 Rs.5,478.72

4b Providing & Fixing BIS approved 2 HP submersible motar starter all complete as per direction of engineer in charge. (As per sub Estimate no.- 4b) 1 Nos. Rs.4,741.20 Rs.4,741.20

4c Providing & Fixing BIS approved 5 HP submersible motar starter all complete as per direction of engineer in charge. (As per sub Estimate no.- 4c) 1 Nos. Rs.6,321.60 Rs.6,321.60

5a Supply & Installation of 90-220 V range single phase7. 5 KVA automatic voltage stabilizer make- Sen & Pandit/ Vertex/ISI marked Stabilizer of reputed make. (As per sub Estimate no.- 05) 1 Nos. Rs.26,340.00 Rs.26,340.00

5b Supply & Installation of 90-220 V range single phase 5.0 KVA automatic voltage stabilizer make- Sen & Pandit/ Vertex/ISI marked Stabilizer of reputed make. (As per sub Estimate no.- 05) 1 Nos. Rs.21,072.00 Rs.21,072.00

6A Providing and Laying Distrbution network of 90 MM High Density Polyethylene pipe (HDPE pipe) all complete as per direction of E/I. (As per sub Estimate no.- 6A ) * 1 per m 794.94 Rs.794.94

6B Providing and Laying Distrbution network of 75 MM High Density Polyethylene pipe (HDPE pipe) all complete as per direction of E/I. (As per sub Estimate no.- 6B ) * 1 per m 649.30 Rs.649.30

6C Providing and Laying Distrbution network of 63 MM High Density Polyethylene pipe (HDPE pipe) all complete as per direction of E/I. (As per sub Estimate no.- 6C ) * 1 per m 552.30 Rs.552.30

6D Providing and Laying Distrbution network of 50 MM High Density Polyethylene pipe (HDPE pipe) all complete as per direction of E/I. (As per sub Estimate no.- 6D ) * 1 per m 439.05 Rs.439.05

6E Providing and Laying Distrbution network of 40 MM High Density Polyethylene pipe (HDPE pipe) all complete as per direction of E/I. (As per sub Estimate no.- 6E ) * 1 per m 395.10 Rs.395.10

7a Cost of replacement of riser / delivery pipe by 50 mm dia G.I.Pipe from T/well to PVC Tank 1 per m Rs.603.29 Rs.603.29

7b Cost of replacement of riser / delivery pipe by 65 mm dia G.I.Pipe from PVC Tank to Distribution main 1 per m Rs.703.49 Rs.703.49

7c Cost of replacement of riser / delivery pipe by 80 mm dia G.I.Pipe for wash out 1 per m Rs.862.06 Rs.862.06

7d Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end). 80mm dia Pipe 1 Job Rs.2,347.00 Rs.2,347.00

7e Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end). 50mm dia Pipe 1 Job Rs.925.27 Rs.925.27

7f Supplying all materials labours & fixing 50mm dia. G.I pipe for using as filling station etc. All as per direction of E/I. 1 Job Rs.3,756.61 Rs.3,756.61

8 Estimate for supply & installation of water storage tank (5000 Ltr. =5000 X 1) as per direction of engineer in charge. (As per sub Estimate no.- 08) 1 Job Rs.55,840.80 Rs.55,840.80

9 Installation of Electronically Regulated Doser type chlorinator using Sodium Hypo Chlorite (Hypo NaOCl) (As per sub Estimate no.-09) 1 Nos. Rs.24,775.40 Rs.24,775.40

10 Providing and erecting 8M high staging with ladder of ISA65x65x6 and 16mm dia MS bar as trade @ 400mm c/c and GI enclosure to house electric switch panel & treatment unit (where required) of suitably designed MS section of angle, channel, etc. as per drawing attached. (As per sub Estimate no.-10) * 1 Job Rs.734,253.84 Rs.734,253.84

11 Estimate for Painting of 8M Steel Staging all complete as per direction of engineer in charge. (As per sub Estimate no.- 11) 1 Job Rs.21,282.72 Rs.21,282.72

12a Estimate for Providing GI enclosure to house electric switch panel for steel structure staging all complete. (As per sub Estimate no.- 12) * 1 per m2 Rs.1,581.77 Rs.1,581.77

12 b Repair/ Replacement of M.S angle / channel / Roof Sheet including riveted/ welded/bolted in built up sections, trusess and framed work, including cutting,hoisting,fixing in position and applying a priming coat of approved primer all complete 1 per Kg Rs.109.57 Rs.109.57

13a Estimate for Construction of floor of staging etc. all complete as per direction of engineer in charge. (As per sub Estimate no.- 13) * 1 per m2 Rs.1,625.51 Rs.1,625.51

14 Providing ladder in staging including all accessories etc. all complete. (As per sub Estimate no.- 14) 1 Job Rs.13,148.93 Rs.13,148.93

15 Providing New house connection for each house hold including supplying all materials, labours, tools and making ferrule connection with 20 mm dia MDPE and 15mm G.I Pipes with all fittings etc all complete. (As per sub Estimate no.- 15) 1 Each Rs.2,623.46 Rs.2,623.00

15a Providing New house connection without retrofitting for each house hold including supplying all materials, labours, tools and making ferrule connection with 20 mm dia MDPE and 15mm G.I Pipes with all fittings etc all complete. (As per sub Estimate no.- 15a) 1 Each Rs.2,197.00 Rs.2,197.00

16 Repairing of House Connection (As per sub Estimate no.- 16) 1 Nos. Rs.801.79 Rs.801.79

16A Repairing of House Connection with leakage at ferrule (As per sub Estimate no.- 16A) 1 Nos. Rs.1,495.06 Rs.1,495.06

16B Minor repairs to House Connection (As per sub Estimate no.- 16B) 1 Nos. Rs.191.76 Rs.191.76

17 Replacing of damage Bib cock with New Bib cock (As per sub Estimate no.- 17) 1 Nos. Rs.115.90 Rs.115.90

18 Repairing of 3 HP/2 HP Pump Motor (As per sub Estimate no.- 18) 1 Nos. Rs.9,355.97 Rs.9,355.97

18b Repairing of 5 HP Pump Motor (As per sub Estimate no.- 18b) 1 Nos. Rs.16,583.66 Rs.16,583.66

19 Repairing of Starter (As per sub Estimate no.- 19) 1 Nos. Rs.1,580.40 Rs.1,580.40

20 Repairing of Stabilizer (As per sub Estimate no.- 20) 1 Nos. Rs.3,160.80 Rs.3,160.80

21 Supplying & fitting 2.5 mm2 copper service cable from power point from nearest source up-to pumping station. (As per sub Estimate no.- 21) 1 per m Rs.136.97 Rs.136.97

22 Cleaning of one 5000 Ltr capacity overhead pvc tank and getting water quality tested from departmental lab. (As per sub Estimate no.- 22) 1 Nos. Rs.526.80 Rs.526.80

23A Repairing of Leakages in HDPE Pipe line with PCC cutting & Restoration. (For HDPE Laid at depth 0.5 to 1.0 m)(As per sub Estimate no.- 23) 5 10 #REF!

90 mm Dia 1 Nos. Rs.1,671.01 Rs.1,671.01

75 mm Dia 1 Nos. Rs.1,652.04 Rs.1,652.04

63 mm Dia 1 Nos. Rs.1,596.20 Rs.1,596.20

50 mm Dia 1 Nos. Rs.1,563.54 Rs.1,563.54

40 mm Dia 1 Nos. Rs.1,536.15 Rs.1,536.15

23B Repairing of Leakages in HDPE Pipe line without PCC cutting & Restoration.(For HDPE Laid at depth 0.5 to 1.0 m)(As per sub Estimate no.- 23)

90 mm Dia 1 Nos. Rs.1,262.21 Rs.1,262.21

75 mm Dia 1 Nos. Rs.1,243.25 Rs.1,243.25

63 mm Dia 1 Nos. Rs.1,187.41 Rs.1,187.41

50 mm Dia 1 Nos. Rs.1,154.75 Rs.1,154.75

40 mm Dia 1 Nos. Rs.1,127.35 Rs.1,127.35

24A Repairing of Leakages in HDPE Pipe line with PCC cutting & Restoration. (For HDPE Laid at depth 0.0 to 0.5 m)(As per sub Estimate no.- 24)

90 mm Dia 1 Nos. Rs.1,590.94 Rs.1,590.94

75 mm Dia 1 Nos. Rs.1,571.97 Rs.1,571.97

63 mm Dia 1 Nos. Rs.1,516.13 Rs.1,516.13

50 mm Dia 1 Nos. Rs.1,483.47 Rs.1,483.47

40 mm Dia 1 Nos. Rs.1,456.08 Rs.1,456.08

24B Repairing of Leakages in HDPE Pipe line without PCC cutting & Restoration.(For HDPE Laid at depth 0.0 to 0.5 m)(As per sub Estimate no.- 24)

90 mm Dia 1 Nos. Rs.1,182.14 Rs.1,182.14

75 mm Dia 1 Nos. Rs.1,163.17 Rs.1,163.17

63 mm Dia 1 Nos. Rs.1,107.33 Rs.1,107.33

50 mm Dia 1 Nos. Rs.1,074.67 Rs.1,074.67

40 mm Dia 1 Nos. Rs.1,047.28 Rs.1,047.28

25 Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) 1 m Rs.127.49 Rs.127.49

26 Replacing damaged portion of riser and delivery pipe 8 meter staging with CPVC / UPVC pipe and providing gun metal Gate valve. (Sub Estimate No.26)

Replacing damaged portion 50 mm dia. CPVC / UPVC Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe 1 m Rs.833.40 Rs.833.40

Replacing damaged portion 80 mm dia. CPVC / UPVC Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe 1 m Rs.1,990.78 Rs.1,990.78

Replacing CPVC / UPVC Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. 1 Nos. Rs.915.00 Rs.915.00

Replacing CPVC / UPVC Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. 1 Nos. Rs.2,240.00 Rs.2,240.00

27 Development of Twell. (Sub Estimate No.27) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) 1 Job Rs.16,973.50 Rs.16,973.50

28 Repairing and painting of RCC staging (Sub Estimate No.28) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) 1 Job Rs.75,437.76 Rs.75,437.76

29 Restoration of road for pipeline work having trench size 300 mm. Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) 1 per meter Rs.362.26 Rs.362.26

30 Providing and fixing 19mm PVC/Block board with KitKat to affix/hang starter, fuses, IoT devices etc all complete as per the directions of the E/I. 1 Job Rs.3,000.00 Rs.3,000.00

31 Providing 50 mm GI pipe for lowering the riser pipe of submersible pump all complete as per the directions of the E/I. (Sub Estimate No.30) 1 Job Rs.1,512.51 Rs.1,512.51

32 Providing and fixing MS clamp consisting of 32mm x 5mm thick two no. rings spaced suitably distance apart around the tank and six nos. L type flats suitably connected with the rings and the other leg suitably connected with the top of the steel structure as per dirction of E/I. 1 Job Rs.3,000.00 Rs.3,000.00

33 Providing and fixixng of New PVC 5000 L Tank Cover with all accessories. 1 Job Rs.300.00 Rs.300.00

34 Providing and fixing M.S Stabiliser Stand near panel Board to keep stabiliser safe. 1 Job Rs.2,500.00 Rs.2,500.00

35 Renovation (Repairing and painting) of Attendent Cum Pump room & toilet. (As per sub Estimate no.- 31) 1 Job Rs.31,613.61 Rs.31,613.61

36 Renovation (Repairing and painting) of Existing Boundry wall of Length 29Mtr and height 1.5Mtr. all complete as per direction of E/I. (As per sub Estimate no.- 32) 1 per meter Rs.1,733.82 Rs.1,733.82

37 Campus development by land filling and brick soaling. (As per sub Est.no.-33) 1 Job Rs.27,302.80 Rs.27,302.80

38 Replacement of Existing Solar driven Pump with Electric driven single phase 2 H.P. submersible pump set having discharging capacity 3 lps at a total head of 45meter (approx) of KSB/ Kirloskar or equivalent make with all accessories & fittings etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & commissioning as per standards specifications and direction of E/I. (As per sub Est. no.- 34) 1 Job Rs.88500.00 Rs.88,500.00

39 Supplying, installation Testing & commissioning of Solar Pannel plate etc all complete as per direction of E/I. (As per sub Est. no.- 35) 1 Job Rs.15,750.00 Rs.15,750.00

40 Supplying, installation Testing & commissioning of Variable Frequency Drive (VFD), Change over Switch and Net Energy Metering (NEM) system (As per sub Est. no.- 36) 1 Job Rs.60,450.00 Rs.60,450.00

41 Providing and Fixing 12 VOLT Solar Battery as per direction of E/I. (As per sub Est. no.- 37) 1 Job Rs.35,000.00 Rs.35,000.00

42 Providing all labours, tools and materials to repair the leakage of different sizes of pipe al different places including earthwork in excavation, opening of joint, dewatering of the trenches, making lead caulked joint & back filling the trenches etc. all complete work (As per sub Est. no.- 38)

(i) without road cutting 1 Nos. Rs.820.00 Rs.820.00

(ii) with Pucca road cutting 1 Nos. Rs.2,006.73 Rs.2,006.73

(i) without road cutting 1 Nos. Rs.890.00 Rs.890.00

(ii) with Pucca road cutting 1 Nos. Rs.2,076.73 Rs.2,076.73

(i) without road cutting 1 Nos. Rs.1,180.00 Rs.1,180.00

(ii) with Pucca road cutting 1 Nos. Rs.2,366.73 Rs.2,366.73

(i) without road cutting 1 Nos. Rs.1,250.00 Rs.1,250.00

(ii) with Pucca road cutting 1 Nos. Rs.2,436.73 Rs.2,436.73

43 Repairing of 63/25 kva transformer inclusing LT pannel rapair in pump house Including Conductor,fuse relay,Timer as required,ST- CTBT pannel repair,Transformer Oil ( 630Ltr) Make-Servo etc all complete as per direction of engineer in charge. 1 Nos. Rs.12,000.00 Rs.12,000.00

44 Providing all labours, materials and cleaning of RCC water VAT from inside and doing chlorination etc. all complete work as per specification & direction of E/I. (As per sub Est. no.- 39) 1 Nos. Rs.1,053.60 Rs.1,053.60

45 Construction of 200 mm x 150 mm x 125 m deep T/W etc. with UPVC Pipe all complete and as per direction of E/I. (as per sub-estimate no.40). 1 Nos. Rs.361,106.00 Rs.361,106.00

46 Construction of 200 mm x 150 mm x 125 m deep T/W etc. with MS Pipe all complete and as per direction of E/I. (as per sub-estimate no.41). 1 Nos. Rs.474,807.00 Rs.474,807.00

47 Construction of 300 mm x 200 mm x 125 m deep T/W etc. with MS Pipe all complete and as per direction of E/I. (as per sub-estimate no.42). 1 Nos. Rs.727,318.15 Rs.727,318.15

48 Construction of 450 mm x 300 mm x 125 m deep T/W etc. with MS Pipe all complete and as per direction of E/I. (as per sub-estimate no.43). 1 Nos. Rs.1,390,348.00 Rs.1,390,348.00

Painting of 10000 Gallon Water Tower. (as per sub-estimate no.44). 1 Nos. Rs.164,266.00 Rs.164,266.00

Painting of 20000 Gallon Water Tower. (as per sub-estimate no.45). 1 Nos. Rs.179,058.00 Rs.179,058.00

Painting of 40000 Gallon Water Tower. (as per sub-estimate no.46). 1 Nos. Rs.243,020.00 Rs.243,020.00

Painting of 50000 Gallon Water Tower (as per sub-estimate no.47). 1 Nos. Rs.312,122.00 Rs.312,122.00

49 Provision of pump operator 1 Nos. Rs.4,000.00 Rs.4,000.00

50 Payment of electricity bills as per actual electricity bills.

BoQ (Fixed Cost)

I. Fixed Costs (WLS (Q/NQ))

(a) Cost of pump operator

1 nos for 365 days per month 48000 12.00 4000.00 48000.00

Sub Total a= 48000.00

(b) Cost of energy charges

Capacity of motor pump say 17.50 HP=(.746x17.5=13.055 kW) kW 2.24

Avg. running hrs,/day 8

Energy charges per year= avg. running hrs/dayx.746x17.5x365 per unit 6534.96 2.6 16990.896

fixed charges per month 12 100.00 3600.00

duty charges @6% of energy charge 1019.45

SubTotal b= 21610.35

Total Fixed Cost (I) = 69,610.35

Contractor's profit @ 10% on (II)= 11,761.03

Add GST @ 18% on ( II)= 2,116.99

Total Cost (I) 83,488.37

Bill of Quantity 2 (Variable Cost)

1 WATER SUPPLY: DUCTILE IRON (DI) SPECIALS

1.1 Providing Ductile Iron Push on special confirming to IS 9523:2000

1.1.1 100mm diameter 11.25⁰ Each 1366.00

1.1.2 100mm diameter 22.50⁰ Each 1464.00

1.1.3 100mm diameter 45⁰ Each 2064.00

1.1.4 100mm diameter 90⁰ Each 1817.00

1.1.5 150mm diameter 11.25⁰ Each 2148.00

1.1.6 150mm diameter 22.50⁰ Each 2207.00

1.1.7 150mm diameter 45⁰ Each 2480.00

1.1.8 150mm diameter 90⁰ Each 3145.00

1.1.9 200mm diameter 11.25⁰ Each 3232.00

1.1.10 200mm diameter 22.50⁰ Each 3396.00

1.1.11 200mm diameter 45⁰ Each 4172.00

1.1.12 200mm diameter 90⁰ Each 5369.00

1.1.13 250mm diameter 11.25⁰ Each 4235.00

1.1.14 250mm diameter 22.50⁰ Each 4622.00

1.1.15 250mm diameter 45⁰ Each 5706.00

1.1.16 250mm diameter 90⁰ Each 7465.00

1.1.17 300mm diameter 11.25⁰ Each 5932.00

1.1.18 300mm diameter 22.50⁰ Each 7077.00

1.1.19 300mm diameter 45⁰ Each 8673.00

1.1.20 300mm diameter 90⁰ Each 11217.00

1.1.21 350mm diameter 11.25⁰ Each 7801.00

1.1.22 350mm diameter 22.50⁰ Each 9197.00

1.1.23 350mm diameter 45⁰ Each 11701.00

1.1.24 350mm diameter 90⁰ Each 16627.00

1.1.25 400mm diameter 11.25⁰ Each 11195.00

1.1.26 400mm diameter 22.50⁰ Each 12825.00

1.2 Providing Ductile Iron(DI) push on specials confirming to IS 9523:2000

1.2.1 400mm diameter 45⁰ Each 16224.00

1.2.2 400mm diameter 90⁰ Each 22716.00

1.2.3 450mm diameter 11.25⁰ Each 13998.00

1.2.4 450mm diameter 22.50⁰ Each 15967.00

1.2.5 450mm diameter 45⁰ Each 20976.00

1.2.6 450mm diameter 90⁰ Each 28788.00

1.2.7 500mm diameter 11.25⁰ Each 16939.00

1.2.8 500mm diameter 22.50⁰ Each 20568.00

1.2.9 500mm diameter 45⁰ Each 28165.00

1.2.10 500mm diameter 90⁰ Each 39127.00

1.2.11 600mm diameter 11.25⁰ Each 25143.00

1.2.12 600mm diameter 22.50⁰ Each 31833.00

1.2.13 600mm diameter 45⁰ Each 41729.00

1.2.14 600mm diameter 90⁰ Each 60864.00

1.3 Providing Ductile Iron push on specials confirming to IS 9523:2000 socketed DI equal tees

1.4 Providing Ductile Iron push on specials confirming to IS 9523:2000 double socketed with flanged branch DI unequal Tees

1.5 Providing Ductile Iron push on specials confirming to IS 9523:2000 all socketed DI unequal Tees

1.6 Providing Ductile Iron push on specials confirming to IS 9523:2000 all socketed DI reducers/tapers

1.7 Providing Ductile Iron push on specials confirming to IS 9523:2000 all DI flanged socketed, DI flanged spigot, MS end plates

1.7.1 D.I. flanged socketed

1.7.2 D.I. flanged socketed 100 mm Each 1543.00

1.7.3 D.I. flanged socketed 150 mm Each 2499.00

1.7.4 D.I. flanged socketed 200 mm Each 3374.00

1.7.5 D.I. flanged socketed 250 mm Each 4978.00

1.7.6 D.I. flanged socketed 300 mm Each 6179.00

1.7.7 D.I. flanged socketed 350 mm Each 8882.00

1.7.8 D.I. flanged socketed 400 mm Each 10778.00

1.8 Providing Ductile Iron push on specials confirming to IS 9523:2000 all DI flanged MJ collar

2 Water supply works

2.1 Removing the GI pipes, cleaning, washing and using at spot or conveying from work site to office/store with all lead and lift i/c removal of all items such as collars, elbows, tees, bends etc,

2.2 Labour charges for laying and jointing GI pipes with earthwork i/c collars, elbows, tees, bends etc. with cuts and threads, white lead paint, conveying the material from store to work site and returning the surplus at store

2.2.1 15mm dia. GI m 10.00

2.2.2 20mm dia. GI m 13.00

2.2.3 25mm dia. GI m 19.00

2.2.4 40mm dia. GI m 24.00

2.2.5 50mm dia. GI m 32.00

2.2.6 65mm dia. GI m 32.00

2.2.7 80mm dia. GI m 32.00

2.3 Cutting charges for CI/DI pipes laid in the ground with necessary tools

2.3.1 100mm dia pipes Each 75.00

2.3.2 125mm dia pipes Each 79.00

2.3.3 150mm dia pipes Each 83.00

2.3.4 175mm dia pipes Each 92.00

2.3.5 200mm dia pipes Each 117.00

2.3.6 225mm dia pipes Each 125.00

2.3.7 250mm dia pipes Each 167.00

2.3.8 300mm dia pipes Each 208.00

2.3.9 375mm dia pipes Each 229.00

2.3.10 400mm dia pipes Each 250.00

2.4 Making cemenr mortar (1:1) and hemp yarn joint for CI pipes i/c cost of all materials viz. cement, sand, hemp, curing for 10 days complete

2.5 Removing CI/DI valves and its tail piece from the pipeline, cleaning, washing, painting and returning the same at store

2.5.1 50mm dia. Each 148.00

2.5.2 80mm dia. Each 250.00

2.5.3 100mm dia. Each 265.00

2.5.4 125mm dia. Each 267.00

2.5.5 150mm dia. Each 339.00

2.5.6 175mm dia. Each 353.00

2.5.7 200mm dia. Each 473.00

2.5.8 225mm dia. Each 491.00

2.5.9 250mm dia. Each 691.00

2.5.10 300mm dia. Each 819.00

2.5.11 375mm dia. Each 828.00

2.5.12 400mm dia. Each 1166.00

2.6 Removing and cleaning CI/DI pipes and specials i/c jointing materials, washing (excluding valves)

2.7 Conveying CI/DI pipes and specials through transportation vehicles

2.7.1 upto 5km i/c loading and unloading qnt 150.00

2.7.2 upto 5km to 10 km excluding loading and unloading qnt 26.00

2.7.3 beyond 10km excluding loading and unloading qnt 16.00

2.8 Fixing DI/CI specials of mechanical jointing of different sizes after setting into the pipeline i/c cleaning, inserting rubber gasket, tightening with bolts & nuts i/c hire charges for T&P, appurtenances and lifting equipments

2.17.1 100mm to 200mm dia. dia. Each 46.00

2.17.2 250mm to 400mm dia. dia. Each 76.00

2.9 Providing and fixing DI Resilient seated soft sealing SLUICE VALVE of variouis dia. with body bonnet of Ductile Iron (DI) conforming ti IS-1865 with the latest amendments and of grade GGG 40/50, shaft of stainless steel, wedge fully rubber lined with EDPM seals of NBR and the valves should be vacum tight and 100% leak proof with face to face dimensions as per IS 14846-2000 with the latest amendments only. The stem sealing should be with toroidal sealing rings (minimum 2 " O " rings). Body and bonnet should be coated with Electrostatically applied Epoxy Powder Coating with minimum coating thickness of 250 micron both inside and outside. The rate is inclusive of cost of valves, T.P set, galvanized bolts & nuts and rubber insertions etc. but excluding earth work. For PN-10: (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate.) etc. complete

2.9.1 For sluice Valve of 50mm Each 5535.00

2.9.2 For sluice Valve of 80mm Each 10393.00

2.9.3 For sluice Valve of 100mm Each 10884.00

2.9.4 For sluice Valve of 150mm Each 17490.00

2.9.5 For sluice Valve of 200mm Each 28709.00

2.9.6 For sluice Valve of 250mm Each 46491.00

2.9.7 For sluice Valve of 300mm Each 60325.00

2.9.8 For sluice Valve of 350mm Each 93233.00

2.9.9 For sluice Valve of 400mm Each 125367.00

2.10 Providing and fixing Wafer type single flange Butterfly valve conforming to relevant IS 13099/9991 EN GGG40/50 with latest amendments as detailed below of the following diameter and types with TP set and conveying to work site, loading and unloading, stacking etc. with all lead and lift. The rate is inclusive of the cost of valve, TP set, rubber insertion, bolts and nuts and excluding earth work excavation.For PN 10.0 (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate.

2.10.1 For sluice Valve of 100mm Each 5849.00

2.10.2 For sluice Valve of 150mm Each 12553.00

2.10.3 For sluice Valve of 200mm Each 13971.00

2.10.4 For sluice Valve of 250mm Each 15374.00

2.10.5 For sluice Valve of 300mm Each 17346.00

2.10.6 For sluice Valve of 350mm Each 23477.00

2.10.7 For sluice Valve of 400mm Each 33092.00

2.11 Providing and fixing of Double Flanged Resilient seated short body Butterfly valves of various dis. As per IS 13095/en 593 with integral DI seat face with approved soft sealing with body and disc of Ductile Iron (DI) of grade GGG-40/50, Body seat & Seal retaining ring of SS 304/CF8, Shaft of stainless steel AISI 410/420/431, Bronze shaft bearing, periferal disk, seal end "o" rings of EPDM, double eccentric disk. Body and disk should be coated with electrostatcially applied epoxy powder coating with a coating thickness of 250 micron both inside and out side. The rate is inclusive of cost of valve, TP set, galvanised bolts and nuts and rubber insertions. For PN 10.0 (All the drilled holes in the body shall be of through holes, no tapped holes will be allowed.) (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate.) etc. complete

2.11.1 For Valve of PN 10.0 and 700mm Each 184739.00

2.11.2 For Valve of PN 10.0 and 750mm Each 239773.00

2.11.3 For Valve of PN 10.0 and 800mm Each 265385.00

2.11.4 For Valve of PN 10.0 and 900mm Each 313821.00

2.11.5 For Valve of PN 10.0 and 1000mm Each 407895.00

2.12 Providing & Fixing sluice valves/ Butterfly Valves (labour charges only) conforming to relevant ISS with latest amendments as detailed below for the following diameter and types with two Each of MJ collars, two flanged spigots, conveying to work site, loading, unloading, stacking with appurtenances. with all lead and lifts, aligning, fixing and testing with appurtenances. etc. complete.

2.1.2.1 For sluice valve with accessories - 50mm dia. Each 341.00

2.1.2.2 For sluice valve with accessories - 80mm dia. Each 381.00

2.1.2.3 For sluice valve with accessories - 100mm dia. Each 463.00

2.1.2.4 For sluice valve with accessories - 150mm dia. Each 524.00

2.1.2.5 For sluice valve with accessories - 200mm dia. Each 769.00

2.1.2.6 For sluice valve with accessories - 250mm dia. Each 1167.00

2.1.2.7 For sluice valve with accessories - 300mm dia. Each 1262.00

2.13 Providing and fixing DI MJ specials such as branches and bends suitable for DI K7 and K9 pipes and CI LA class pipes, as per IS 13382 with latest amendments with complete accessories and fixing at site excluding earth work but including loading, unloading, freight charges etc. complete for:

2.13.1 DI MJ specials - Branch 100 x 100mm Each 1701.00

2.13.2 DI MJ specials - Branch 150 x 150mm Each 2673.00

2.38.3 DI MJ specials - Branch 150 x 100mm Each 2322.00

2.38.4 DI MJ specials - Bend 100 x 90 degree mm Each 1203.00

2.38.5 DI MJ specials - Bend 100 x 45 degree Each 1174.00

2.38.6 DI MJ specials - Bend 150 x 90 degree Each 2322.00

2.38.7 DI MJ specials - collar 100mm dia. Each 2287.00

2.38.8 DI MJ specials - collar 150mm dia. Each 4102.00

2.14 Providing, fabricating and fixing at site various diameter MS MJ ends with dummy plates (END CAPS) to suit CI / DI spigots end as per the sketch. The cost is inclusive of all materials, i.e, rubber 'O' rings, flanges, bolts and nuts, dummy plates, consumables, hire charges, tools and welding equipments, lead and lifts, etc. complete as per the instructions of Engineer in charge.

2.14.1 For CI / DI pipes of 100mm dia. Each 1158.00

2.14.2 For CI / DI pipes of 150mm dia. Each 1609.00

2.14.3 For CI / DI pipes of 200mm dia. Each 2226.00

2.14.4 For CI / DI pipes of 250mm dia. Each 3213.00

2.14.5 For CI / DI pipes of 300mm dia. Each 3230.00

2.14.6 For CI / DI pipes of 400mm dia. Each 5077.00

2.15 Providing and fixing of Extension spindle rods,PN 10 /16 suitable for Gate valve of following dia for open and closing application, Extension Spindle lengths shall be available on required sizes as per site conditions, spindle shall be of fixed type, suitable size of MS Square bar epoxy coated, bottom adaptor & Spindle cap (epoxy coated /galvanised) ductile iron Gr40. Protection tube of PVC, Top and Bottom cover / Bottom Connector shall be made by PVC, Bolt shall be made by Zinc coated steel 8.8 Split pin shall be made by Electro galvanized, this set up should help to have a buried application of Gate Valves etc. complete as per the directions of the Engineer-in-Charge.

2.16 Providing & fixing RCC Pre-cast Cover Slab of size 0.8 m x 0.8 m x 0.15m of M25-Design mix concrete with 12 mm steel @ 120 mm c/c both ways, over Gate valve extension spindle with central opening along with lid for smooth operation with appurtenances., complete with all lead and lifts etc. complete Each 2386.00

2.17 Conveying with all lead & lift and fixing C.I/D.I specials, bends, branches, tees,with appurtenances, all sizes and aligning.

2.17.1 50 mm dia to 100 mm dia Each 105.00

2.17.2 125 mm dia to 225 mm dia Each 131.00

2.17.3 250 mm dia to 600 mm dia Each 203.00

3 Attendind leakages

3.1 Providing & fixing CI/DI pipes socket leak repair MJ clamps for attending to leak joints in socket / spigot joints of CI / DI pipes with necessary earth work excavation including using of pneumatic breakers and JCB excavator wherever required and providing DI MJ leak repair clamp, including cost of all materials required for jointing comprising of DI MJ clamps and its accessories such as rubber gaskets made of SBR / EPDM on the socket face, making the socket / spigot joint water tight at the operating pressure, backfilling with available earth and consolidation and bailing out water wherever necessary etc. complete and In all types of road surfaces like Concrete, Asphalt roads etc, for:

3.1.1 CI / DI pipes of 100mm dia. Each 2357.00

3.1.2 CI / DI pipes of 150mm dia. Each 3563.00

3.1.3 CI / DI pipes of 200mm dia. Each 4032.00

3.1.4 CI / DI pipes of 250mm dia. Each 5255.00

3.1.5 CI / DI pipes of 300mm dia. Each 6426.00

3.1.6 CI / DI pipes of 400mm dia. Each 9059.00

3.1.7 CI / DI pipes of 450mm dia. Each 11257.00

3.2 Attending to leaking socket / spigots joints in CI / DI pipes in all types of road surfaces including concrete and asphalt roads, with necessary earth work excavation including using of pneumatic breakers and JCB excavator wherever required for jointing DI MJ clamp and its accessories such as rubber gaskets made of SBR / EPDM on the socket face, making the socket / spigot joint water tight at the operating pressure, backfilling with available earth and consolidation and bailing out water wherever necessary etc.complete.

3.2.1 For CI / DI pipes of 100mm dia. Each 722.00

3.2.2 For CI / DI pipes of 150mm dia. Each 814.00

3.2.3 For CI / DI pipes of 200mm dia. Each 820.00

3.2.4 For CI / DI pipes of 250mm dia. Each 954.00

3.2.5 For CI / DI pipes of 300mm dia. Each 1254.00

3.2.6 For CI / DI pipes of 400mm dia. Each 1289.00

3.2.7 For CI / DI pipes of 450mm dia. Each 1406.00

3.3 Cutting Asphalt /Concrete road surface using machine cutter for leakage pit with earth work excavation in all classifications of soil including all lead and lifts bailing out water with pumps including barricading, danger lighting etc., as per requirement and disposing of the excavated stuff as directed. After attending the leak, refilling the trench for 30 cm depth quarry dust above and around pipelines and balance with available earth in layers not exceeding 20 cms in depth, compacting Each deposited layer by ramming including watering and consolidation by mechanical means approved by Engineer Incharge. (Work to be carried out as per leak repair manual and the rate includes hire charges of dewatering Pump, tractor, Jeep with all kinds of Labour in a Complete manner). m3 1157 m2 1157.00

3.4 Road Reinstatement of Asphalt /Concrete roads after leak attending with earth work excavation of compacted soil depositing on bank with all lead and lifts including danger lighting and barricading. Providing, laying, spreading and compacting graded stones aggregate as per wet mix macadam specifications. Applying tack coat on granular base such as WBM and WMM surface hot bitumen primer at 4 kg per 10 sqm, heating bitumen in layer to be laid with boiler fitted with spray set of 300 mm thickness. Above laid with bituminous concrete or M20 concrete premixed with bituminous binder at 5.4 to 5.6% of mix and filler, to achieve the desired compaction to give minimum of 45mm thickness compacted. The work shall be carried as per leak repair manual and includes all kinds of materials disposing off the excess excavated Earth with all lead and lifts by vehicle including loading, unloading, labour, HOM of machinery etc. in a complete manner. m2 1690.00

4.1 Providing and laying Ductile Iron pipes of class conforming to IS 8329:2000 with latest amendments, conveying to work site, rolling and lowering into trenches, laying true to line, level and perfect linking at joints, testing and commissioning, including loading and unloading at both destinations, cutting of pipes wherever necessary, jointing with DI specials (excluding cost of specials) and rubber gaskets, cleaning the socket and spigot end with soap solution, applying soft soap to the socket and spigot ends before insertion of rubber gaskets, jacking and fixing in perfect conditions etc. The cost to include soap solution, soft soap, waste etc. and giving necessary hydraulic test to the required pressure as per ISS with all lead and lifts and cost of all jointing materials. (The contractor will make his own arrangements for water for testing. Earth work excavation in trenches to be measured and paid for seperately) Note: In sewerage projects for internal cement mortal lining ( CML ) of DI pipes, if High Alumina Cement ( HAC ) as recommended in Annexure B clause 16.3 of IS8329:2000 is considered in place of Slag or Sulphate Resistance Cement ( SRC ), the cost of pipes may be increased by 5-6% from the prices listed. For DI K7 pipes:

4.1.1 100mm dia pipe m 1460.00

4.1.2 150mm dia pipe m 2016.00

4.1.3 200mm dia pipe m 2576.00

4.1.4 250mm dia pipe m 3140.00

4.1.5 300mm dia pipe m 3968.00

4.1.6 350mm dia pipe m 4999.00

4.1.7 400mm dia pipe m 5976.00

4.2 Labour charges for laying & jointing of DI pipes of all classes rolling and lowering into trenches, laying true to line, level and perfect linking at joints and commissioning, including loading and unloading at both destinations and cuts of pipes wherever necessary including jointing of DI pipes and specials (excluding cost of pipes,rubber gasket and specials) with rubber gaskets including cleaning the sockets and spigot ends with saop solutions and applying soft soap to the spigot and socket end before insertion of rubber gaskets, jointing and fixing in perfect conditions including the cost of soap solution, soft soap, waste etc. and giving necessary hydraulic test to the required pressure as per ISS etc. with all leads and lifts (Earth work excavation in trenches,conveying of materials from stores to be measured and paid for separately) (Contractor will make his own arrangements for procuring water for testing) etc. complete for:

4.2.1 100mm dia pipe m 72.00

4.2.2 150mm dia pipe m 103.00

4.2.3 200mm dia pipe m 150.00

4.2.4 250mm dia pipe m 261.00

4.2.5 300mm dia pipe m 311.00

4.2.6 350mm dia pipe m 339.00

4.2.7 400mm dia pipe m 378.00

4.5 Labour charges for making flanged joints including cost of jointing materials comprising of rubber insertion, galvanised bolts and nuts including giving hydraulic test to the required pressure as per ISS with all lead & lift (contractor will make his own arrangement for procuring water for testing) etc. complete

4.5.1 Pipes and specials of dia 50mm. Each 113.00

4.5.2 Pipes and specials of dia 80mm. Each 124.00

4.5.3 Pipes and specials of dia 100mm. Each 208.00

4.5.4 Pipes and specials of dia 150mm. Each 310.00

4.5.5 Pipes and specials of dia 200mm. Each 334.00

4.5.6 Pipes and specials of dia 250mm. Each 498.00

4.5.7 Pipes and specials of dia 300mm. Each 520.00

4.5.8 Pipes and specials of dia 350mm. Each 707.00

4.5.9 Pipes and specials of dia 400mm. Each 1033.00

4.6 Providing RUBBER JOINTING for CI / DI pipes with rubber gaskets including cleaning the socket and spigot ends with soap solution and applying soft soap to the spigot and socket ends before insertion of rubber gaskets, jacking and fixing in perfect conditions including cost of soap solution, soft soap, waste etc with all lead and lift including cost of jointing materials etc.complete for:

5 RCC Overhead tanks

7.1 Providing and fixing MS ladder between landings, 45 cms wide using angle iron of specified sizes, 20mm MS bars at 25 cms. centre to centre, with necessary supports of same angle iron etc. as directed, including hand railing on both sides with 25mm dia. GI pipes with angle iron props at 2 mtrs. intervals and 0.5M heigh, including fixing in ground with CC 1:2:4 and two coats of anticorrosive bituminous paint etc. with all lead and lifts etc. complete with:

7.1.1 MS angle of 65 x 65 x 8mm m 4377.00

7.1.2 MS angle of 65 x 65 x 10mm m 4801.00

7.6 Providing, Laying and Jointing Cast Iron (CI) double flanged pipes true to line / hoisting of DI flanged pipe in position and aligning to correct plumb, including cost of jointing materials, conveying to work spot with all lead and lifts etc.complete.

7.6.1 For double flanged CI pipes of 80mm dia. m 2245.00

7.6.2 For double flanged CI pipes of 100mm dia. m 3010.00

7.6.3 For double flanged CI pipes of 150mm dia. m 4808.00

7.6.4 For double flanged CI pipes of 200mm dia. m 6592.00

7.6.5 For double flanged CI pipes of 250mm dia. m 9272.00

7.7 Providing and fixing lightening arrestor with aluminium strip 25mm x 3mm size including finial and grounding, aluminium strip to be embeded in one of the columns in and independent GI conduit of 40mm dia. pipe suitably jointed by collars with all specials with all lead and lifts etc. complete for:

7.7.1 For Over Head Tanks upto 6 M staging Each 8088.00

7.7.2 For Over Head Tanks upto 9 M staging Each 9387.00

7.7.3 For Over Head Tanks upto 12M staging Each 11530.00

7.7.4 For Over Head Tanks above 12M staging Each 13889.00

7.9 Providing, of DI flanged pipe conforming to IS 8329 : 2000 with latest amendments with Cement Mortar Lining (CML) with Portland Slag Cement as per IS 455:1989 and Metallic Zinc Coating as per annexure A of IS 8329 with finishing layer of Bituminous Coating as per Annexure C of IS 8329 and Flanges: Metallic zinc rich epoxy paint & Bituminous Coating, laying true to line and hoisting in position and aligning to correct plumb including cost of jointing material, conveying to work spot with all lead and lifts etc., complete. For PN 10.0

7.11 Providing Ductile Iron Push on special confirming to IS 9523:2000 - All Double Socket Duck Foot DI Bends:

8.2 Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to RCC structures like floor and walls of reservoirs, sewe, effluent and water treatment plants, over head tanks, etc. prepared by mixing in the ratio of 5:2 (5 parts integral crystalline slurry 2 parts water) for horizontal and vertical surfaces and applying the same from negative (internal) side with the help of synthetic fibre brush. The material shall meet the requirements as specified in ACI - 212-3R-2010 ie. by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 Bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self healing of cracks upto a width of 0.50 mm. The work shall be carried out all complete as per specification and the direction of the Engineer in charge. The product performance shall carry guarantee for 10 years against any leakage. For horizontal and vertical surfaces in two coats @ 0.70 kg per sqm per coat m2 433.00

9.15 Lowering and laying and fusion welding Jointing for HDPE Pipes Grade PE- 80 / PE-100 conforming to IS 4984-2016, of specified dia. including hydrualic testing and commissioning etc.(Contractor will make his own arrangements for procuring water for testing) for:

11.1 Providing, Laying and Fixing of GI pipes conforming to IS 1239:1990 with latest amendments complete with GI fittings (excluding the cost of fittings) with cuts and threads wherever necessary, including testing for water tightness, with all lead and commissioning. (contractor will make his own arrangements for procuring water for testing) For:Heavy Duty GI Pipe etc. complete.

11.2 For Medium Duty GI pipe:

11.2.6 Medium Duty GI pipe of 50mm dia m 584.00

11.2.7 Medium Duty GI pipe of 65mm dia m 719.00

11.2.8 Medium Duty GI pipe of 80mm dia m 891.00

11.2.9 Medium Duty GI pipe of 100mm dia m 1245.00

11.3 For Heavy Duty GI pipe:

11.3.6 Heavy Duty GI pipe of 50mm dia m 679.00

11.3.7 Heavy Duty GI pipe of 65mm dia m 834.00

11.3.8 Heavy Duty GI pipe of 80mm dia m 1009.00

11.3.9 Heavy Duty GI pipe of 100mm dia m 1412.00

11.4 Providing and fixing GI union in existing GI pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required etc. complete for:

11.4.6 20.88.6: 50 mm nominal bore Each 660.00

11.4.7 20.88.7: 65 mm nominal bore Each 878.00

11.4.8 20.88.8: 80 mm nominal bore Each 1041.00

11.5 Providing lead caulked joints to spun iron or CI pipes and specials with spun yarn and lead, including caulking and giving satisfactory hydraulic test corresponding to the required pressure etc. complete.for:

11.5.1 Spun / CI / DI pipes 80MM Each 481.00

11.5.2 Spun / CI / DI pipes 100MM Each 500.00

11.5.3 Spun / CI / DI pipes 150MM Each 747.00

11.5.4 Spun / CI / DI pipes 200MM Each 944.00

11.5.5 Spun / CI / DI pipes 250MM Each 1210.00

11.5.6 Spun / CI / DI pipes 300MM Each 1425.00

11.6 Providing wrought mild steel (galvanized) GI collar confirming to IS 1239-II, 1991 with latest amendments if any.

11.6.6 For 50 mm dia GI collar: Each 267.00

11.6.7 For 65 mm dia GI collar: Each 312.00

11.6.8 For 80 mm dia GI collar: Each 421.00

11.6.9 For 100 mm dia GI collar: Each 505.00

11.6.10 For 125 mm dia GI collar: Each 636.00

11.6.11 For 150 mm dia GI collar: Each 695.00

11.7 Supply and delivery at site wrought middle steel (galvanized) GI elbow confirming to IS 1239-II, 1991 with latest amendments if any for:

11.7.6 For 50 mm dia GI elbow Each 267.00

11.7.7 For 65 mm dia GI elbow Each 297.00

11.7.8 For 80 mm dia GI elbow Each 417.00

11.7.9 For 100 mm dia GI elbow Each 490.00

11.7.10 For 125 mm dia GI elbow Each 578.00

11.7.11 For 150 mm dia GI elbow Each 651.00

11.8 Supply and delivery at site wrought middle steel (galvanized) GI bend confirming to IS 1239-II, 1991 with latest amendments if any.

11.8.6 For 50 mm dia GI BEND Each 358.00

11.8.7 For 65 mm dia GI BEND Each 404.00

11.8.8 For 80 mm dia GI BEND Each 490.00

11.8.9 For 100 mm dia GI BEND Each 600.00

11.8.10 For 125 mm dia GI BEND Each 680.00

11.8.11 For 150 mm dia GI BEND Each 724.00

11.9 Supply and delivery at site wrought middle steel (galvanized) GI tee confirming to IS 1239-II, 1991 with latest amendments if any.

11.9.6 For 50 mm dia GI TEE Each 297.00

11.9.7 For 65 mm dia GI TEE Each 373.00

11.9.8 For 80 mm dia GI TEE Each 434.00

11.9.9 For 100 mm dia GI TEE Each 607.00

11.9.10 For 125 mm dia GI TEE Each 775.00

11.9.11 For 150 mm dia GI TEE Each 914.00

11.1 Supply and delivery at site wrought middle steel (galvanized) GI socket confirming to IS 1239-II, 1991 with latest amendments if any.

11.10.6 For 50 mm dia GI socket Each 297.00

11.10.7 For 65 mm dia GI socket Each 373.00

11.10.8 For 80 mm dia GI socket Each 454.00

11.10.9 For 100 mm dia GI socket Each 563.00

11.10.10 For 125 mm dia GI socket Each 614.00

11.10.11 For 150 mm dia GI socket Each 731.00

11.11 Supply and delivery at site wrought middle steel (galvanized) GI plugs confirming to IS 1239-II, 1991 with latest amendments if any.

11.11.6 For 50 mm dia GI Plugs Each 199.00

11.11.7 For 65 mm dia GI Plugs Each 237.00

11.11.8 For 80 mm dia GI Plugs Each 256.00

11.11.9 For 100 mm dia GI Plugs Each 358.00

11.11.10 For 125 mm dia GI Plugs Each 432.00

11.11.11 For 150 mm dia GI Plugs Each 490.00

11.12 Supply and delivery at site wrought middle steel (galvanized) GI union confirming to IS 1239-II, 1991 with latest amendments if any.

11.12.6 For 50 mm dia GI Union Each 267.00

11.12.7 For 65 mm dia GI Union Each 351.00

11.12.8 For 80 mm dia GI Union Each 578.00

11.12.9 For 100 mm dia GI Union Each 622.00

11.12.10 For 125 mm dia GI Union Each 666.00

11.12.11 For 150 mm dia GI Union Each 783.00

11.2 Lowering, Laying and Jointing GI pipes conforming to IS 1239:1990 with latest amendments complete with GI fittings (excluding the cost of fittings) with cuts and threads wherever necessary, including testing for water tightness, with all lead and commissioning. (contractor will make his own arrangements for procuring water for testing) for etc. complete.

Bill of Quantity 3 (Variable Cost)

13 SUBMERSIBLE PUMPSETS AND REPLACEMENT OF PARTS

13.1 Rewinding of submersible pumpset with copper winding wires of appropriate guage, as per specifications and / or directions of the departmental officials, including all materials, labour, equipment and testing. for all types of submersible pumpsets etc.(with guarantee period not less than 6 months) for

13.1.1 For all types of submersible pumpsets upto 3.0 H.P. Each 2710.00

13.1.2 above 3 HP and upto 5.0 H.P. Each 2934.00

13.1.3 above 5.0 HP and upto 5.5H.P. Each 3116.00

13.1.4 above 5.5 HP and upto 6.0H.P. Each 3296.00

13.1.5 above 6.0 HP and upto 6.5H.P. Each 3479.00

13.1.6 above 6.5 HP and upto 7.0H.P. Each 3659.00

13.1.7 above 7.0 HP and upto 7.5H.P. Each 3839.00

13.1.8 above 7.5 HP and upto 8.0H.P. Each 4019.00

13.1.9 above 8.0 HP and upto 8.5H.P. Each 4201.00

13.1.10 above 8.5 HP and upto 9.0H.P. Each 4382.00

13.1.11 above 9.0 HP and upto 9.5H.P. Each 4562.00

13.1.12 above 9.5 HP and upto 10.0H.P. Each 4744.00

13.1.13 above 10 HP and upto 11 H.P. Each 5157.00

13.1.14 above 11 HP and upto 12 H.P. Each 5570.00

13.1.15 above 12 HP and upto 13 H.P. Each 5983.00

13.1.16 above 13 HP and upto 14 H.P. Each 6397.00

13.1.17 above 14 HP and upto 15 H.P. Each 6811.00

13.2 Replace the components of submersible pump sets, requiring replacements decided by the departmental officials, with respective make of damaged ones, including all materials, labour, equipments and testing etc.(with gurantee of period not less than 1 year) for:

13.2.1 The bowls of same type and make Each 1500.00

13.2.2 The Intermediate piece (IP) with IP leaded bronze brush. Each 1050.00

13.2.3 The Oil Seal. Each 350.00

13.2.4 The Oil Seal.and steel bush Each 250.00

13.2.5 The Guide Vane Each 700.00

13.2.6 The Impeller (Shell moulded with aluminium and bronze.) Each 1500.00

13.2.7 The discharge outlet (DO) bearing DO steel brush DO bearing. Each 2050.00

13.2.8 The steel bearing bush (DO steel bush) Each 400.00

13.2.9 The allen screw Each 1200.00

13.2.10 The pump shaft made out of stainless steel counterless ground with key way (upto 8 stages). Extra for Each stage @ Rs.40/-. Each 1500.00

13.2.11 The pump key (stainless steel) Each 650.00

13.2.12 The pump coupling (stainless steel) Each 1500.00

13.2.13 The Non Return Valve (NRV) assembly complete with rubber 'O' ring. Each 650.00

13.2.14 The cable guard Each 350.00

13.2.15 The strainer Each 450.00

13.2.16 The brass filter Each 1050.00

13.2.17 The Labour Charges for overhauling of the pump set. Each 900.00

13.3 Replace the components of motor parts of submersible pump sets, items requiring replacements decided by the departmental officials, with respective make of damaged ones, including all materials, labour, equipments and testing etc and wtih guarantee/ warranty for one year for:

13.3.1 The STATOR of motor upto 3 H.P Each 1500.00

13.3.2 The STATOR of motor 3 to 4 H.P Each 2500.00

13.3.3 The STATOR of motor 4 to 5 H.P Each 3500.00

13.3.4 The ROTOR of motor upto 3.0 H.P Each 1200.00

13.3.5 The ROTOR of motor 3 to 4 H.P Each 1500.00

13.3.6 The ROTOR motor 4 to 5 H.P Each 2000.00

13.3.7 The upper flange Each 650.00

13.3.8 The lower flange Each 650.00

13.3.9 upper/ lower housing Each 1200.00

13.3.10 The Lock Ring Each 350.00

13.3.11 The Carbon Housing Each 2000.00

13.3.12 The Carbon Housing (Thrust bearing block assembly complete with segment bearing pad. Each 2200.00

13.3.13 The Carbon Housing (Top carbond / ferrodo padding) Each 350.00

13.3.14 The Stud and Nuts Each 200.00

13.3.15 The Gun Metal bearing, centrifugally cast Aluminium Bronze bearing Each 850.00

13.3.16 The Circlips Each 200.00

13.3.17 The Motor base with pin Each 500.00

13.3.18 The Transportation of pumping machineries Each 1200.00

13.3.19 The Re-errection charges of pumping machineries including overhauling Each 2000.00

13.3.20 The lifting of submersible pumpset from well. Each 1500.00

13.3.21 The Labour charges only for overhauling Each 3000.00

13.3.22 Providing of Thermosetting Plastic i.e., Fibere Glass reinforced polyster sheet moulding compound(SMC) pump house with SMC door & canopy etc...,complete component as directed by the departmental officers. Each 12000.00

13.4 Providing, Single Phase Submersible Pump Sets of 100mm dia (4 inch) suitable for bore well confirming to IS 8034-2000 specifications, to work site with testing of as per instructions of engineer incharge of work and latest amendments etc. complete.

13.4.1 0.50 HP/0.37kW - 5 STG(stage) Each 10170.00

13.4.2 0.50 HP/0.37kW - 7 STG(stage) Each 10855.00

13.5 For 0.75 HP/0.55KW

13.11 Providing Submersible Pump Set of 150mm dia suitable for bore well and confirming to IS 8034-2000;3Phase, SS Bowl & Impeller with Low volt Motor as per specifications, to work site as per necessary ammendments and instructions of engineer incharge of work. For 3 HP etc. complete.

13.11.1 3.00 HP - 300 LPM @ 26 m = 5 STG Outlet Dia - 2.50" Each 23168.00

13.11.2 3.00 HP - 155 LPM @ 42 m = 7 STG Outlet Dia - 2.00" Each 24334.00

13.11.3 3.00 HP - 135 LPM @ 56 m = 8 STG Outlet Dia - 2.00" Each 25910.00

13.11.4 3.00 HP - 120 LPM @ 55 m = 9 STG Outlet Dia - 2.00" Each 26627.00

13.11.5 3.00 HP - 90 LPM @ 66 m = 10 STG Outlet Dia - 2.00" Each 28113.00

13.12.1 4.00 HP - 360 LPM @ 30 m = 6 STG Outlet Dia - 3.00" Each 22628.00

13.12.2 4.00 HP - 245 LPM @ 42 m = 8 STG Outlet Dia - 2.50" Each 23319.00

13.12.3 4.00 HP - 155 LPM @ 56 m = 9 STG Outlet Dia - 2.00" Each 24107.00

13.12.4 4.00 HP - 135 LPM @ 70 m = 5 STG Outlet Dia - 2.00" Each 24993.00

13.12.6 4.00 HP - 90 LPM @ 88 m = 12 STG Outlet Dia - 2.00" Each 26730.00

13.13.1 5.00 HP - 300 LPM @ 39 m = 5 STG Outlet Dia - 2.50" Each 26310.00

13.13.2 5.00 HP - 245 LPM @ 56 m = 8 STG Outlet Dia - 2.50" Each 27010.00

13.14.1 6.50 HP - 360 LPM @ 45 m = 5 STG Outlet Dia - 3.00" Each 26930.00

13.14.2 6.50 HP - 300 LPM @ 52 m = 6 STG Outlet Dia - 2.50" Each 27813.00

13.14.3 6.50 HP - 245 LPM @ 70 m = 8 STG Outlet Dia - 2.50" Each 29930.00

13.15.1 7.50 HP - 360 LPM @ 60 m = 5 STG Outlet Dia - 3.00" Each 28116.00

13.15.2 7.50 HP - 300 LPM @ 65 m = 6 STG Outlet Dia - 2.50" Each 30010.00

13.15.3 7.50 HP - 245 LPM @ 84 m = 8 STG Outlet Dia - 2.50" Each 32819.00

13.22 Supply and delivery at site Brand new best make PVC insulated cable of Flat 3 core (sheathed) of nominal cross sectional area as per IS 694-1990 with ISI Mark and as per its latest amendments.

13.23 Supply and delivery at site of brand new best make pressure gauge bourdon type as per IS 778/1984 with ISI Mark and as per its latest amendments.

13.23.1 Size 63 mm Each 416.00

13.23.2 Size 80 mm Each 597.00

13.23.3 Size 100 mm Each 654.00

13.24 Supply and delivery at site of brand new best make gate valve as per IS 778/1984 with ISI Mark and as per its latest amendments

13.24.1 Size 50 mm Each 1250.00

13.24.2 Size 65 mm Each 1450.00

13.24.3 Size 80 mm Each 1650.00

13.25 Supply and delivery at site of brand new best make non-return valve as per IS 778/1984 with ISI Mark and as per its latest amendments

13.25.1 Size 50 mm Each 1250.00

13.25.2 Size 65 mm Each 1550.00

13.25.3 Size 80 mm Each 1750.00

13.23 Supply, installing,testing and commissioning COMMON control panel consisting of the following INCOMING:1 No set of Phase indicating lamps with SFU of suitable rating 1 No, Analog Ammeter, 1 No Analog Voltmeter 1ni with Phase selector switch, Isolating switch OUTGOING for Main Electrical Pump: 1 No. MCB 1 No. DOL of S/D Starter suitable for respective HP 1 No. Electrcal Protection Like single Phase preventor, under voltage over Volage, under current over current & dry run protection suitable for the pump described above 1 no Indoor type NOTE:

1) DOL- Direct Online Starter

2) S-D- Star Delta Starter etc. complete.

13.23.1 Upto 3 HP pumps Each 6500.00

13.23.2 3 to 6 HP pumps Each 9550.00

13.23.3 6 to 15 HP pumps Each 15900.00

13.24 for outdoor

13.24.1 Upto 3 HP pumps Each 7500.00

13.24.2 3 to 6 HP pumps Each 10500.00

13.24.3 6 to 15 HP pumps Each 17500.00

13.25 Supply and delivery at site best indigenous brand new power capacitor as per IS 2834/1986 with latest amendments with KPTCL authorities and erection, electrification and commissioning of the same at the location of respective pump sets. kVAR 550.00

13.26 Supply and delivery at site delivery of best indigenous brand new MCB (Miniature Circuit Breakers) of required capacity as per IS 88228/1978 and its latest amendments and with ISI Mark of 6/10/16/20/25/40 Amps with scalable box. per 3 poles 1150.00

13.27 Supply and delivery of galvanized mild steel tubes of 6mtr standard length heavy duty (C Class) as per IS 1239 (Part-I) 1990 with latest amendments with ISI Mark (one end fitted with Heavy Duty collar and other end fitted with protective cover)

13.28 Supply and delivery at site 50mm(2”) dia heavy duty unplasticized PVC Column pipes with heavy duty collars,rubber profile ring,vibration control profile ring,freezing and turbulence free leak proof EPDM ring with ISI mark with its latest amendments m 550.00

13.29 Supply and delivery at site 50mm(2”) dia heavy duty CI adopter set complete suitable for uPVC Column pipes for Submersible pumpsets SET 1550.00

13.3 Supply and delivery at site Accessories for Single Phase pumpset like SS Groove Nipples,SS Studs & Nuts,Screw Clips &water proof Insulation Tape etc complete with ISI mark SET 4500.00

13.31 Supply and delivery at site Stringing of heavy duty Naylone/PP rope with ISI etc complete suitable for Single phase Pumpsets. m 40.00

13.32 Labour charges for Erection, Electrification and commissioning of Pump sets, including aligning and balancing of all items including supply and erection of two pair of supporting clamps, bore well caps, cable clips and water tight gland cable protectors, bolts, nuts, valve and gauges,tools and equipments etc., involved in the job as per specifications, with necessary tests as per specifications, with testing of as per instructions of engineer incharge of work. Job 6500.00

13.33 Labour charges for erection of indoor type panel board and meter board units with all necessary materials and labour tools and equipments including cement concrete for foundation/bed etc,complete as per specification, with testing of as per instructions of engineer incharge of work. Job 1350.00

13.34 Labour charges for erection of outdoor type panel board and meter board units with all necessary materials and labour, tools and equipments including providing cement concrete foundation bed etc., complete as per specification, with testing of as per instructions of engineer incharge of work. Job 1450.00

13.35 Labour charges for providing connection using insulated sheathed steel wire cable as per IS 1554/ 1988 with latest amendments from KPTCL pole to meter board unit, with all necessary materials ,tools and equipments,as per specificationswith testing of as per instructions of engineer incharge of work. .

13.35.4 3 x 10 sqmm (suitable for over head mains) m 165.00

13.36 Providing main connection from pole PVC insulated sheathed steel wire cable in new trench as per IS 1554/ 1988 with latest amendments with ISI mark from KPTCL pole to meter board unit. m 135.00

13.37 Providing main connection from pole PVC insulated sheathed steel wire cable in GI pipe as per IS 1554/ 1988 with latest amendments with ISI mark from KPTCL pole to meter board unit. m 85.00

13.38 Providing and fixing suitable for 1.1 KV class UG cable filled with necessary bitumen/insulating compound complete with terminals, clamps,bolts,nuts and washers etc. with necessary materials and labour tools and equipments as per instructions of engineer incharge of work.

13.39 Earthing: Providing and fixing and wiring earth electrode for grounding circuits IC cutouts and other equipments on the meter board in the pit. The pits should be filled up with equal proportion of salt and charcoal 150mm around the pipe to complete depth. The connection from the pipe to the conduits etc. is to established through GI wire of sizes as per clause 7.3.3 of IS 732 using 12mm bolts, nuts, washers and check nuts, the pipe shall have 16 through holes of 12mm dia. Job 3750.00

13.4 Supply and delivery of Centrifugal pumpset at site brand new best make and with discharge duty confirming to ISI standards and its latest amendments. Discuss

13.40.1 2 HP, Size 65x50 Head 13M, Discharge 462 LPM Each 15610.00

13.40.2 2 HP, Size 50x40 Head 22M, Discharge 186 LPM Each 16993.00

13.40.3 3 HP, size 50x40 Head 30M, Discharge 198 LPM Each 18816.00

13.40.4 5 HP, size 80x65 Head 23.50M, Discharge 600 LPM Each 22310.00

13.40.5 5 HP, size 50x40 Head 46M, Discharge 174 LPM Each 26417.00

13.40.6 7.5 HP, size 100x100 Head 195M, Discharge 1200 LPM Each 30520.00

13.40.7 7.5 HP, size 80x65 Head 195M, Discharge 1200 LPM Each 33619.00

13.40.8 7.5 HP, size 65x50 Head 46M, Discharge 360 LPM Each 35150.00

13.40.9 10 HP, size 80x65 Head 34.50M, Discharge 840 LPM Each 37623.00

13.40.10 12.5 HP, size 100x100 Head 25M, Discharge 1560 LPM Each 38331.00

13.40.11 12.5 HP, size 80x65 Head 40M, Discharge 780 LPM. Each 46710.00

13.40.12 15 HP, size 80x65 Head 44M, Discharge 900 LPM Each 53967.00

13.40.13 20 HP, size 100x80 and 42M, Discharge 1320 LPM Each 65918.00

13.41 Supply and delivery at site brand new best make pressure guage suitable for centrifugal pump confirming to latest IS standards.

13.41.1 pressure guage 80MM Each 597.00

13.41.2 pressure guage 100MM Each 654.00

13.42 Supply and delivery at site brand new best make level guage suitable for centrifugal pump confirming to latest IS standards. Each 750.00

13.43 Supply and delivery at site brand new best make starter/ control panel suitable for following HP centrifugal pump confirming with ISI mark and its latest amendments.

13.43.1 Upto 7.5 HP centrifugal pump Each 9500.00

13.43.2 7.5 to 10 HP centrifugal pump Each 15550.00

13.43.3 10 to 12 HP centrifugal pump Each 35650.00

13.44 Supply, delivery, erection and commissioning at site lighting distribution board suitable for monoblock centrifugal pump confirming with ISI mark and its latest amendments. Each 3500.00

13.45 Supply, delivery, erection and commissioning at site ELCB suitable for monoblock centrifugal pump confirming with ISI mark and its latest amendments. Each 4117.00

13.46 Providing and fixing LT cable of size 4 x 25 Sqm suitable for centrifugal pump sets with ISI mark and its latest amendments. m 562.00

13.47 Supply and delivery at site brand new best make Foot valve suitable for centrifugal pump upto 10HP confirming with ISI mark and its latest amendments. Each 1750.00

13.48 Supply and delivery at site brand new best make Foot valve suitable for centrifugal pump above 12.50HP confirming with ISI mark and its latest amendments. Each 2200.00

13.49 Rewinding of monoblock motor with copper insulaton wire suitable gauge as per ISI specification with all necessary materials and labour,tools and equipments with guarantee period of not less than 12 months

13.49.1 7.5 HP monobloc motor rewinding Job 4000.00

13.49.2 10 HP monobloc motor rewinding Job 6500.00

13.49.3 12.5 HP monobloc motor rewinding Job 8000.00

13.49.4 15 HP monobloc motor rewinding Job 12000.00

13.49.5 20 HP monobloc motor rewinding Job 15000.00

13.49.6 30 HP monobloc motor rewinding Job 20000.00

13.49.7 40 HP monobloc motor rewinding Job 22000.00

13.49.8 50 HP monobloc motor rewinding Job 25000.00

13.49.9 60 HP monobloc motor rewinding Job 35000.00

13.49.10 80 HP monobloc motor rewinding Job 38000.00

13.49.11 100HP monobloc motor rewinding Job 50000.00

13.49.12 120 HP monobloc motor rewinding Job 62000.00

13.49.13 150 HP monobloc motor rewinding Job 65000.00

13.49.14 180 HP monobloc motor rewinding Job 75000.00

13.49.15 200 HP monobloc motor rewinding Job 85000.00

13.5 Providing Ball bearing as per ISI specifiction with guarantee period of not less than 12 months

13.50.1 Bearing cost for 7.5 HP Each 1880.00

13.50.2 Bearing cost for 10HP Each 2050.00

13.50.3 Bearing cost for 12.5 HP Each 2050.00

13.50.4 Bearing cost for 15 HP Each 2550.00

13.50.5 Bearing cost for 20 HP Each 3080.00

13.50.6 Bearing cost for 30HP Each 4050.00

13.50.7 Bearing cost for 40 HP Each 4600.00

13.50.8 Bearing cost for 50 HP Each 6250.00

13.50.9 Bearing cost for 60 HP Each 6500.00

13.50.10 Bearing cost for 80 HP Each 7000.00

13.50.11 Bearing cost for 100 HP Each 7500.00

13.50.12 Bearing cost for 120 HP Each 9000.00

13.50.13 Bearing cost for 150 HP Each 11000.00

13.50.14 Bearing cost for 180 HP Each 12500.00

13.50.15 Bearing cost for 200 HP Each 13500.00

13.51 Providing thrust bearing as per ISI specifiction with guarantee period of not less than 12 months

13.51.1 Bearing cost for 30 HP Each 6500.00

13.51.2 Bearing cost for 40HP Each 7500.00

13.51.3 Bearing cost for 50 HP Each 8500.00

13.51.4 Bearing cost for 60 HP Each 11000.00

13.51.5 Bearing cost for 80 HP Each 13500.00

13.51.6 Bearing cost for 100 HP Each 14000.00

13.51.7 Bearing cost for 120 HP Each 16500.00

13.51.8 Bearing cost for 150 HP Each 18000.00

13.51.9 Bearing cost for 180 HP Each 19500.00

13.51.10 Bearing cost for 200 HP Each 21000.00

13.52 Providing terminal plate as per ISI specifiction with guarantee period of not less than 12 months

13.52.1 terminal plate 7.5 to 12.5 Each 450.00

13.52.2 terminal plate 15 to 30 Each 850.00

13.52.3 terminal plate 40 to 60 Each 1050.00

13.52.4 terminal plate 80 to 120 Each 2000.00

13.52.5 terminal plate 150 to 200 Each 3500.00

13.53 Repairs to Vertical turbine pumps as per ISI specifiction with guarantee period of not less than 12 months V- T Pump

13.53.1 Phosphorous bronze bearing bush for 30 HP to 40 HP Each 4800.00

13.53.2 Phosphorous bronze bearing bush for 50 HP to 60 HP Each 5500.00

13.53.3 Phosphorous bronze bearing bush for 80 HP to 100 HP Each 7500.00

13.53.4 Phosphorous bronze bearing bush for 100 HP to 150 HP Each 8200.00

13.53.5 Phosphorous bronze bearing bush for 180 HP to 200 HP Each 9000.00

13.54 Repairs to Vertical turbine pumps as per ISI specifiction with guarantee period of not less than 12 months V-T PUMP STAGE BUSHES

13.54.1 Phosphorous bronze stage bushes for 30 to 40 HP Each 4500.00

13.54.2 Phosphorous bronze stage bushes for 50 to 60 HP Each 5200.00

13.54.3 Phosphorous bronze stage bushes for 80 to 100 HP Each 7500.00

13.54.4 Phosphorous bronze stage bushes for 100 to 150 HP Each 8500.00

13.54.5 Phosphorous bronze stage bushes for 180 to 200 HP Each 9500.00

13.55 Repairs to Vertical turbine pumps as per ISI specifiction with guarantee period of not less than 12 months V-T PUMP IMPELLER AND NECK RING

13.55.1 IMPELLER AND NECK RING for 30 HP to 40 HP Each 4800.00

13.55.2 IMPELLER AND NECK RING for 50 HP to 60 HP Each 5200.00

13.55.3 IMPELLER AND NECK RING for 80 HP to 100 HP Each 9000.00

13.55.4 IMPELLER AND NECK RING for 100 HP to 150 HP Each 8000.00

13.55.5 IMPELLER AND NECK RING for 180 HP to 200 HP Each 9500.00

13.56 Repairs to Vertical turbine pumps as per ISI specifiction with guarantee period of not less than 12 months HORIZANTAL PUMP

13.56.1 Phosphorous bronze bushes for 7.5 to 15 HP monoblock motor Each 800.00

13.56.2 Phosphorous bronze bushes for 20 HP monoblock motor Each 1800.00

13.56.3 Phosphorous bronze bushes for 40HP to 80HP monoblock motor Each 5800.00

13.56.4 Phosphorous bronze bushes for 100HP to 120HP monoblock motor Each 6500.00

13.56.5 Phosphorous bronze bushes for 150HP to 200 HP monoblock motor Each 8000.00

13.57 BEARING FOR HORIZONTAL PUMP

13.57.1 For 20 HP pump bearing Each 2500.00

13.57.2 For 30 HP Pump bearing Each 3500.00

13.57.3 For 40 to 80 HP pump bearing Each 4500.00

13.57.4 For 60 to 80 HP pump bearing Each 8400.00

13.57.5 For 100 to 150HP pump bearing Each 10200.00

13.57.6 For 180 to 200 HP pump bearing Each 10800.00

13.58 ALL TYPES OF JACK WELL V-T PUMP DETAILS as per ISI specifiction with guarantee period of not less than 12 months -For Pump dismentaling and refitting after attending repairs.

13.58.1 Up to 60 HP Each 10000.00

13.59 For Top body bush fitting

13.59.1 Up to 60 HP Each 2000.00

13.6 For Bottom body bush fitting

13.60.1 Up to 60 HP Each 1450.00

13.61 For Pumps stage body bush fitting Each

13.61.1 Up to 60 HP Each 850.00

13.62 For Pump body necking fitting Each

13.62.1 Up to 60 HP Each 1200.00

13.63 For Impeller breezing making

13.63.1 Up to 60 HP Each 1050.00

13.64 For Pump shaft press throwble

13.64.1 Up to 60 HP Each 680.00

13.65 For Pump open & fitting at work shop

13.65.1 Up to 60 HP Each 3500.00

13.66 For Connecting bush G.M new making Each

13.66.1 Up to 60 HP Each 1875.00

13.67 For Line shaft seat welding making Each

13.67.1 Up to 60 HP Each 450.00

13.68 For Oil inside new Fitting & threading Each

13.68.1 Up to 60 HP Each 1400.00

13.69 For Balancing spaider rubber guide Each

13.69.1 Up to 60 HP Each 1200.00

13.7 For New T.T nipple making

13.70.1 Up to 60 HP Each 3050.00

13.71 For Pump gear box body radial bearing

13.71.1 Up to 60 HP Each 13575.00

13.72 For Gear box ball bearing

13.72.1 Up to 60 HP Each 1500.00

13.73 For Pumping and clean pipe painting

13.73.1 Up to 60 HP Each 1675.00

13.74 For Transportation charges both side

13.74.1 Up to 60 HP Each 2500.00

13.75 Water Treatment Plants HORIZANTAL PUMP ALL TYPES-For Pump open & refitting after repairs

13.75.1 Up to 25HP Each 4900.00

13.76 For Side gland bush

13.76.1 Up to 25HP Each 1500.00

13.77 For Impeller breezing and making

13.77.1 Up to 25HP Each 1100.00

13.78 For Shaft steel welding and making bearing sheet Each

13.78.1 Up to 25HP Each 1100.00

13.79 For Shaft threading making Each

13.79.1 Up to 25HP Each 1250.00

13.8 For Joint rope of 1kg

13.80.1 Up to 25HP Each 700.00

13.81 For Pump shaft bend thrown

13.81.1 Up to 25HP Each 950.00

13.82 For Transportation

13.82.1 Up to 25HP Each 2715.00

13.83 For Pump shaft getting check nut Each

13.83.1 Up to 25HP Each 1050.00

13.84 For Both coupling new set

13.84.1 Up to 25HP Each 8500.00

13.85 Providing and installing of solar photo voltaic (SPV) water pumping system INDUCTION MOTOR, PUMPSETS AND A SUITABLE INVERTER

as per IS specification and instruction of Engineer incharge of work as per IS specification- For 3000 wp/ 3HP submersible with controller

13.85.1 Total head 30 mtrs and shut off dynamic Head 45 mtr and water out put 96000 ltrs/day. Each 267000.00

13.85.2 Total head 50 mtrs and shut off dynamic Head 75 mtr and water out put 57000 ltrs/day. Each 270000.00

13.85.3 Total head 70 mtrs and shut off dynamic Head 100 mtr and water out put 39000 ltrs/day Each 273000.00

13.86 For 4800 wp/ 5HP submersible with controller

13.86.1 Total head 50 mtrs and shut off dynamic Head 70 mtr and water out put 91200 ltrs/day. Each 383000.00

13.86.2 Total head 70 mtrs and shut off dynamic Head 100 mtr and water out put 62400 ltrs/day. Each 386000.00

13.86.3 Total head 100 mtrs and shut off dynamic Head 150 mtr and water out put 40800 ltrs/day. Each 389000.00

13.87 For 6750 wp/ 7.5 HP submersible with controller

13.87.1 Total head 50 mtrs and shut off dynamic Head 70 mtr and water out put 128250 ltrs/day. Each 565000.00

13.87.2 Total head 70 mtrs and shut off dynamic Head 100 mtr and water out put 87750 ltrs/day. Each 568000.00

13.87.3 Total head 100 mtrs and shut off dynamic Head 150 mtr and water out put 57375 ltrs/day. Each 571000.00

13.88 For 9000 wp/ 10HP submersible with controller

13.88.1 Total head 50 mtrs and shut off dynamic Head 70 mtr and water out put 171000 ltrs/day. Each 714000.00

13.88.2 Total head 70 mtrs and shut off dynamic Head 100 mtr and water out put 117000 ltrs/day. Each 717000.00

13.88.3 Total head 100 mtrs and shut off dynamic Head 150 mtr and water out put 76500 ltrs/day. Each 720000.00

P.H.Division,Motipur

Block wise (WLS,PWS, SVS) Ward Details

Sl.No Block Name of Scheme Panchayat Name of PWS Scheme PHED Wards Remarks

PWS Wards No. Total WIMC Wards No No. of Scheme

1 Meenapur Turki Khararoo East Turki Khararoo East 6,10,11,13 4 6,10,11,13 4

2 Turki Khararoo West Turki Khararoo West 11,13 2 11,13 2

4 Harka Manshahi Harka Manshahi 4,5,11,12,13 5 4,5,11,12,13 5

5 Paroo Anandpur Kharauni Anandpur Kharauni 4,6,7,8,13 5 4,6,7,8,13 5

6 Dharfari Dharfari 10,13,14,15 4 10,13,14,15 4

7 Moujamma Moujamma 12,13,14,15 4 12,13,14,15 4

8 Moujamma Moujamma 1,2,3,9,10,11 6 1,2,3,9,10,11 6

9 Pandeh Pandeh 1,2,3,4,5 5 1,2,3,4,5 5

11 Paroo South Paroo South 5,6,7,8,11,12 6 5,6,7,8,11,12 6

12 Devariya East Devariya East 1,2,11,12,13,15 6 1,2,11,12,13,15 6

13 Kanti Mustaffapur Mustaffapur 1 1 1 1

14 Har chanda Har chanda 2,11,13 3 2,11,13 3

15 Ramnath Dhamauli East Ramnath Dhamauli East 7,9,11,15 4 7,9,11,15 4

16 Panapur Haweli Panapur Haweli 8,11,13,14,15,16 6 8,11,13,14,15,16 6

17 Sherukahi Sherukahi 1,3,5 3 3,5 2

18 Har chanda Har chanda 3 1 3 1

19 Ramnath Dhamauli East Ramnath Dhamauli East 6,8 2 6,8 2

20 Ramnath Dhamauli West Ramnath Dhamauli West 1,3,8,15 4 8 1

21 Sherukahi Sherukahi 10 1

22 Ramnath Dhamauli West Ramnath Dhamauli West 6 1

23 Mustaffapur Mustaffapur 9 1 9 1

24 Marwan Jiyan Khurd Jiyan Khurd 1,3,6,7 4 1,3,6,7 4

25 Jiyan Khurd Jiyan Khurd 4,5,6,15 4 4,5,6,15 4

26 Karjadih Karjadih 10,12 2 10,12 2

27 Bakrkagaon Utri Bakrkagaon Utri 3,9 2 3,9 2

28 Mohammadpur Subey Mohammadpur Subey 3,4,5,11,12,13,14 7 3,4,5,11,12,13,14 7

29 Bakrkagaon Utri Bakrkagaon Utri 5,12,13 3 5,12,13 3

31 Sahebganj Madhopur Hazari Madhopur Hazari 3,4,5 3 5,6,7,12 4

32 Rampur Asli Rampur Asli 14 1

33 Saraiya Basantpur South Basantpur South 7,10 2 7,10 2

34 Saraiya Saraiya 3,8,9 3 8,9 2

35 Kudhani Chajjan Harishankar Chajjan Harishankar 5,7,8,9,10 5 5,7,8,9,10 5

Total No. of Scheme (WLS) 125

1 Meenapur Meenapur Meenapur 7,8 1

2 Kudhani Turki Turki 9,10,13,14,15 1

3 Kanti Navrullahpur Bangra Navrullahpur Bangra 1,2,3,4,10 1

4 Saraiya Saraiya Saraiya 4,5,7,11,12,13 1

5 Paroo Moujjama Moujjama 4,5,6,7,8 1

6 Marwan Bakrkagaon Utri Bakrkagaon Utri 1,6,7,8 1

7 Meenapur Panapur Panapur 3,4 1

8 Saraiya Basantpur South Basantpur South 1,2,3,5,6,8,9 1

9 Meenapur Turki Khararoo West Turki Khararoo West 1,3,5 1

10 Sahebganj Madhopur Hazari Madhopur Hazari 8,9,10,11 1

11 Motipur Motipur Kathaiya Motipur Kathaiya 6,7,8,9,10 1

12 Kudhani Chajjan Harishankar Chajjan Harishankar 1,2,3,4,6 1

13 Paroo Phulwariya Phulwariya 7,8,9,10 1

14 Paroo Dharphari Dharphari 2,3,6,8,9,11 1

Total No. of Scheme (PWS) 14

1 Saraiya Chako Chapra Ramkrishan Dubiyahi 6,13 1

2 Saraiya Jagir Tola Ramkrishan Dubiyahi 14 1

3 Kanti Saieen Saieen 1,2,3,4,13,14,15 1

4 Kanti Saieen Brijlal Saieen 5,6,7 1

5 Kanti Madhukar Chhapra Saieen 8,9,10 1

6 Kanti Rannu Rai Saieen 11,12 1

7 Meenapur Chatursi Chatursi 7,8,9 1

8 Meenapur Bhagwan Chhapra Chatursi 5,6,12 1

9 Meenapur Khoja Pakari Chatursi 13,14 1

10 Meenapur Neknama Chatursi 10,11 1

11 Meenapur Basudev Banua Chatursi 1 1

12 Paroo Matihani Gyaspur 9,14,15 1

13 Saraiya Shekh Dhanauj Ramkrishan Dubiyahi 7,8,9 1

14 Saraiya Jalalpur Ramkrishan Dubiyahi 10,11,12 1

15 Paroo Gyaspur Gyaspur 1,2,3,4,5,6,7,8 1

Total No. of Scheme (SVS) 15

Executive Engineer

P.H.Division, Motipur

NIT No.:-01R1/Motipur(NQ)2026-2027/O&M-PHED

NAME OF WORK- Comprehensive operation and maintenance, routine repairs and Special repairs of i.) Rural Piped Water Supply Scheme (PWS)- 12 Nos, ii.) Single Village piped water supply schemes (SVS)- 15 Nos, iii.) Ward level Piped Water Supply Schemes in non quality affected wards (WLS)-125 Nos based on item rates; constructed by the Public Health Engineering Department including payment to the pump operators, electricity bills for five years.

Date of Tender :- 15.05.2026

Estimated Cost :- 238863300.00

Earnest Money :- 3389000.00

Duration of Maintenance Period 5 Year

Cost of BOQ :- 10000.00

SI NO. PARTICULARS No. of Scheme AMOUNT

1 Comprehensive operation and maintenance, routine repairs and Special repairs of i.) Rural Piped Water Supply Scheme (PWS)- 14 Nos, ii.) Single Village piped water supply schemes (SVS)- 15 Nos, iii.) Ward level Piped Water Supply Schemes in non quality affected wards (WLS)-125 Nos based on item rates; constructed by the Public Health Engineering Department including payment to the pump operators, electricity bills for five years. (i) WLS(Non Quality):-125 (ii) PWSNon Quality) -14 (iii) SVS Non Quality)-15 . 238,863,300.00

Total Amount 238,863,300.00

Rupees Twenty Three Crore Eighty Eight Lacs Sixty Three Thousand Three Hundred Only

1 Estimated cost Rs. 238,863,300.00 (A)

2 Cost of Govt. Material :- NIL NIL (B)

3 Name of the Contractor :-

4 Address of the Contractor :-

5 I/we offer in Figures……. in words………………… % (Percentage) High on the rate for the fixed cost (Part I) for operation of the schemes. IN FIG.

6 I/we offer in Figures……. in words………………… % (Percentage) High / Less on the rate for the variable cost (Part-II) for maintenance of the schemes. IN FIG. 100

7 Average rate quoted by the bidder 0.00

Note :- 1.) Bidders has to quote rate in Percentage High/Less only. 0.6

Note :- 2.) Items/ Quantity of Work will be decided by the department on day to day / priority basis during period of maintenance.

Note :- 3.) The quoted rate for the operation part I (fixed cost) i.e. the payment to the operators and the electricity bills, the quote shall not be negative.

Note :- 4.) The electricity bills shall be paid as per actual.

Note :- 5.) The entry in row 7 shall be considered for decision of financially lowest bid.

Executive Engineer, P.H.Division, Motipur

GOVERNMENT OF BIHAR

Public Health Engineering Department

Bill of Quantity 1 (Variable Cost)

S.N. Description Quantity Unit Rate Total Amount

1A Construction of 150mm X100mmx 125m deep T/W etc. all complete and as per direction of E/I.(As per sub Estimate no.- 1) 1 Nos. Rs.294,314.73 Rs.294,314.73

1B Construction of 150 mmX90m deep drilled T/W etc. all complete and as per direction of E/I. 1 Nos. Rs.180,147.69 Rs.180,147.69

2 Constructing masonry Chamber 100x100x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for Tube Well, and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size ) , necessary excavation, foundation concrete 1:2:4(1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3coarse sand) 12 mm thick with 5% cico fnished with a floating coat of neat cement, out side plastering with cement mortar 1:4 (1 cement : 4coarse sand) 12 mm thick complete as per standard specifications & direction of E/I. (As per sub Estimate no.- 2) 1 Nos. Rs.15,314.08 Rs.15,314.08

3A Supply Installation, commissioning and testing of single phase 3 H.P submersible pump set having discharging capacity 3.35 lps at a total head of 35 meter(approx) of different capacity of KSB/ Kirloskar or equivalent make with all accessories & fittings such as 7.5KVA Stabalizer, cable, panel board etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & commissioning as per standards specifications and direction of E/I. (As per sub Estimate no.- 3a) 1 Nos. Rs.110,628.00 Rs.110,628.00

3AA Supply Installation, commissioning and testing of single phase 3 H.P submersible pump set only having discharging capacity 3.35 lps at a total head of 35 meter(approx) of different capacity of KSB/ Kirloskar or equivalent make with all accessories & fittings etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & commissioning excluding the cost of GI pipes for lowering and cables etc. as per standards specifications and direction of E/I. (As per sub Estimate no.- 3a items) 1 Nos. Rs.25,000.00 Rs.25,000.00

3B Supply Installation, commissioning and testing of single phase 2 H.P submersible pump set having discharging capacity 2.25 lps at a total head of 35 meter(approx) of different capacity of KSB/ Kirloskar or equivalent make with all accessories & fittings such as 7.5KVA Stabalizer, cable, panel board etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & commissioning as per standards specifications and direction of E/I. (As per sub Estimate no.- 3b) 1 Nos. Rs.68,220.60 Rs.68,220.60

3BB Supply Installation, commissioning and testing of single phase 2 H.P submersible pump set having discharging capacity 2.25 lps at a total head of 35 meter(approx) of different capacity of KSB/ Kirloskar or equivalent make with all accessories & fittings etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & commissioning excluding the cost of GI pipes for lowering and cables etc. as per standards specifications and direction of E/I.(As per sub Estimate no.- 3B items) 1 Nos. Rs.20,000.00 Rs.20,000.00

3C Supply Installation, commissioning and testing of three phase 5 H.P submersible pump set including light wiring, power wiring and extension of over head L.T line from nearest point of electric line up to pump room having 50 C/sec. 2900 rpm at a total head of 35 meter(approx) of different capacity of KSB/ Kirloskar or equivalent make with all accessories & fittings etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & commissioning complete set as per standards specifications and direction of E/I. (As per sub Estimate no.- 3c) 1 Nos. Rs.140,107.73 Rs.140,107.73

3CC Supply Installation, commissioning and testing of three phase 5 H.P submersible pump set only having 50 C/sec. 2900 rpm at a total head of 35 meter(approx) of different capacity of KSB/ Kirloskar or equivalent make with all accessories & fittings etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & commissioning excluding the cost of GI pipes for lowering and cables etc. as per standards specifications and direction of E/I. 1 Nos. Rs.40,000.00 Rs.40,000.00

4a Providing & Fixing BIS approved 3 HP submersible motar starter all complete as per direction of engineer in charge. (As per sub Estimate no.- 4a) 1 Nos. Rs.5,478.72 Rs.5,478.72

4b Providing & Fixing BIS approved 2 HP submersible motar starter all complete as per direction of engineer in charge. (As per sub Estimate no.- 4b) 1 Nos. Rs.4,741.20 Rs.4,741.20

4c Providing & Fixing BIS approved 5 HP submersible motar starter all complete as per direction of engineer in charge. (As per sub Estimate no.- 4c) 1 Nos. Rs.6,321.60 Rs.6,321.60

5a Supply & Installation of 90-220 V range single phase7. 5 KVA automatic voltage stabilizer make- Sen & Pandit/ Vertex/ISI marked Stabilizer of reputed make. (As per sub Estimate no.- 05) 1 Nos. Rs.26,340.00 Rs.26,340.00

5b Supply & Installation of 90-220 V range single phase 5.0 KVA automatic voltage stabilizer make- Sen & Pandit/ Vertex/ISI marked Stabilizer of reputed make. (As per sub Estimate no.- 05) 1 Nos. Rs.21,072.00 Rs.21,072.00

6A Providing and Laying Distrbution network of 90 MM High Density Polyethylene pipe (HDPE pipe) all complete as per direction of E/I. (As per sub Estimate no.- 6A ) * 1 per m 794.94 Rs.794.94

6B Providing and Laying Distrbution network of 75 MM High Density Polyethylene pipe (HDPE pipe) all complete as per direction of E/I. (As per sub Estimate no.- 6B ) * 1 per m 649.30 Rs.649.30

6C Providing and Laying Distrbution network of 63 MM High Density Polyethylene pipe (HDPE pipe) all complete as per direction of E/I. (As per sub Estimate no.- 6C ) * 1 per m 552.30 Rs.552.30

6D Providing and Laying Distrbution network of 50 MM High Density Polyethylene pipe (HDPE pipe) all complete as per direction of E/I. (As per sub Estimate no.- 6D ) * 1 per m 439.05 Rs.439.05

6E Providing and Laying Distrbution network of 40 MM High Density Polyethylene pipe (HDPE pipe) all complete as per direction of E/I. (As per sub Estimate no.- 6E ) * 1 per m 395.10 Rs.395.10

7a Cost of replacement of riser / delivery pipe by 50 mm dia G.I.Pipe from T/well to PVC Tank 1 per m Rs.603.29 Rs.603.29

7b Cost of replacement of riser / delivery pipe by 65 mm dia G.I.Pipe from PVC Tank to Distribution main 1 per m Rs.703.49 Rs.703.49

7c Cost of replacement of riser / delivery pipe by 80 mm dia G.I.Pipe for wash out 1 per m Rs.862.06 Rs.862.06

7d Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end). 80mm dia Pipe 1 Job Rs.2,347.00 Rs.2,347.00

7e Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end). 50mm dia Pipe 1 Job Rs.925.27 Rs.925.27

7f Supplying all materials labours & fixing 50mm dia. G.I pipe for using as filling station etc. All as per direction of E/I. 1 Job Rs.3,756.61 Rs.3,756.61

8 Estimate for supply & installation of water storage tank (5000 Ltr. =5000 X 1) as per direction of engineer in charge. (As per sub Estimate no.- 08) 1 Job Rs.55,840.80 Rs.55,840.80

9 Installation of Electronically Regulated Doser type chlorinator using Sodium Hypo Chlorite (Hypo NaOCl) (As per sub Estimate no.-09) 1 Nos. Rs.24,775.40 Rs.24,775.40

10 Providing and erecting 8M high staging with ladder of ISA65x65x6 and 16mm dia MS bar as trade @ 400mm c/c and GI enclosure to house electric switch panel & treatment unit (where required) of suitably designed MS section of angle, channel, etc. as per drawing attached. (As per sub Estimate no.-10) * 1 Job Rs.734,253.84 Rs.734,253.84

11 Estimate for Painting of 8M Steel Staging all complete as per direction of engineer in charge. (As per sub Estimate no.- 11) 1 Job Rs.21,282.72 Rs.21,282.72

12a Estimate for Providing GI enclosure to house electric switch panel for steel structure staging all complete. (As per sub Estimate no.- 12) * 1 per m2 Rs.1,581.77 Rs.1,581.77

12 b Repair/ Replacement of M.S angle / channel / Roof Sheet including riveted/ welded/bolted in built up sections, trusess and framed work, including cutting,hoisting,fixing in position and applying a priming coat of approved primer all complete 1 per Kg Rs.109.57 Rs.109.57

13a Estimate for Construction of floor of staging etc. all complete as per direction of engineer in charge. (As per sub Estimate no.- 13) * 1 per m2 Rs.1,625.51 Rs.1,625.51

14 Providing ladder in staging including all accessories etc. all complete. (As per sub Estimate no.- 14) 1 Job Rs.13,148.93 Rs.13,148.93

15 Providing New house connection for each house hold including supplying all materials, labours, tools and making ferrule connection with 20 mm dia MDPE and 15mm G.I Pipes with all fittings etc all complete. (As per sub Estimate no.- 15) 1 Each Rs.2,623.46 Rs.2,623.00

15a Providing New house connection without retrofitting for each house hold including supplying all materials, labours, tools and making ferrule connection with 20 mm dia MDPE and 15mm G.I Pipes with all fittings etc all complete. (As per sub Estimate no.- 15a) 1 Each Rs.2,197.00 Rs.2,197.00

16 Repairing of House Connection (As per sub Estimate no.- 16) 1 Nos. Rs.801.79 Rs.801.79

16A Repairing of House Connection with leakage at ferrule (As per sub Estimate no.- 16A) 1 Nos. Rs.1,495.06 Rs.1,495.06

16B Minor repairs to House Connection (As per sub Estimate no.- 16B) 1 Nos. Rs.191.76 Rs.191.76

17 Replacing of damage Bib cock with New Bib cock (As per sub Estimate no.- 17) 1 Nos. Rs.115.90 Rs.115.90

18 Repairing of 3 HP/2 HP Pump Motor (As per sub Estimate no.- 18) 1 Nos. Rs.9,355.97 Rs.9,355.97

18b Repairing of 5 HP Pump Motor (As per sub Estimate no.- 18b) 1 Nos. Rs.16,583.66 Rs.16,583.66

19 Repairing of Starter (As per sub Estimate no.- 19) 1 Nos. Rs.1,580.40 Rs.1,580.40

20 Repairing of Stabilizer (As per sub Estimate no.- 20) 1 Nos. Rs.3,160.80 Rs.3,160.80

21 Supplying & fitting 2.5 mm2 copper service cable from power point from nearest source up-to pumping station. (As per sub Estimate no.- 21) 1 per m Rs.136.97 Rs.136.97

22 Cleaning of one 5000 Ltr capacity overhead pvc tank and getting water quality tested from departmental lab. (As per sub Estimate no.- 22) 1 Nos. Rs.526.80 Rs.526.80

23A Repairing of Leakages in HDPE Pipe line with PCC cutting & Restoration. (For HDPE Laid at depth 0.5 to 1.0 m)(As per sub Estimate no.- 23) 5 10 #REF!

90 mm Dia 1 Nos. Rs.1,671.01 Rs.1,671.01

75 mm Dia 1 Nos. Rs.1,652.04 Rs.1,652.04

63 mm Dia 1 Nos. Rs.1,596.20 Rs.1,596.20

50 mm Dia 1 Nos. Rs.1,563.54 Rs.1,563.54

40 mm Dia 1 Nos. Rs.1,536.15 Rs.1,536.15

23B Repairing of Leakages in HDPE Pipe line without PCC cutting & Restoration.(For HDPE Laid at depth 0.5 to 1.0 m)(As per sub Estimate no.- 23)

90 mm Dia 1 Nos. Rs.1,262.21 Rs.1,262.21

75 mm Dia 1 Nos. Rs.1,243.25 Rs.1,243.25

63 mm Dia 1 Nos. Rs.1,187.41 Rs.1,187.41

50 mm Dia 1 Nos. Rs.1,154.75 Rs.1,154.75

40 mm Dia 1 Nos. Rs.1,127.35 Rs.1,127.35

24A Repairing of Leakages in HDPE Pipe line with PCC cutting & Restoration. (For HDPE Laid at depth 0.0 to 0.5 m)(As per sub Estimate no.- 24)

90 mm Dia 1 Nos. Rs.1,590.94 Rs.1,590.94

75 mm Dia 1 Nos. Rs.1,571.97 Rs.1,571.97

63 mm Dia 1 Nos. Rs.1,516.13 Rs.1,516.13

50 mm Dia 1 Nos. Rs.1,483.47 Rs.1,483.47

40 mm Dia 1 Nos. Rs.1,456.08 Rs.1,456.08

24B Repairing of Leakages in HDPE Pipe line without PCC cutting & Restoration.(For HDPE Laid at depth 0.0 to 0.5 m)(As per sub Estimate no.- 24)

90 mm Dia 1 Nos. Rs.1,182.14 Rs.1,182.14

75 mm Dia 1 Nos. Rs.1,163.17 Rs.1,163.17

63 mm Dia 1 Nos. Rs.1,107.33 Rs.1,107.33

50 mm Dia 1 Nos. Rs.1,074.67 Rs.1,074.67

40 mm Dia 1 Nos. Rs.1,047.28 Rs.1,047.28

25 Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) Supplying and laying of submersible flat cable ISI marked 3 core copper wire of suitable size with proper clamping of approved make. (Rate Chattisgarh SOR 34.20.107 Rs.121.00+18% GST) 1 m Rs.127.49 Rs.127.49

26 Replacing damaged portion of riser and delivery pipe 8 meter staging with CPVC / UPVC pipe and providing gun metal Gate valve. (Sub Estimate No.26)

Replacing damaged portion 50 mm dia. CPVC / UPVC Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe Replacing damaged portion 50 mm dia. Riser pipe 1 m Rs.833.40 Rs.833.40

Replacing damaged portion 80 mm dia. CPVC / UPVC Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe Replacing damaged portion 80 mm dia. Riser pipe 1 m Rs.1,990.78 Rs.1,990.78

Replacing CPVC / UPVC Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. Replacing Gate Valve 50 mm dia. 1 Nos. Rs.915.00 Rs.915.00

Replacing CPVC / UPVC Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. Replacing Gate Valve 80 mm dia. 1 Nos. Rs.2,240.00 Rs.2,240.00

27 Development of Twell. (Sub Estimate No.27) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) 1 Job Rs.16,973.50 Rs.16,973.50

28 Repairing and painting of RCC staging (Sub Estimate No.28) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) 1 Job Rs.75,437.76 Rs.75,437.76

29 Restoration of road for pipeline work having trench size 300 mm. Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) Development of Twell. (Sub Estimate No.11) 1 per meter Rs.362.26 Rs.362.26

30 Providing and fixing 19mm PVC/Block board with KitKat to affix/hang starter, fuses, IoT devices etc all complete as per the directions of the E/I. 1 Job Rs.3,000.00 Rs.3,000.00

31 Providing 50 mm GI pipe for lowering the riser pipe of submersible pump all complete as per the directions of the E/I. (Sub Estimate No.30) 1 Job Rs.1,512.51 Rs.1,512.51

32 Providing and fixing MS clamp consisting of 32mm x 5mm thick two no. rings spaced suitably distance apart around the tank and six nos. L type flats suitably connected with the rings and the other leg suitably connected with the top of the steel structure as per dirction of E/I. 1 Job Rs.3,000.00 Rs.3,000.00

33 Providing and fixixng of New PVC 5000 L Tank Cover with all accessories. 1 Job Rs.300.00 Rs.300.00

34 Providing and fixing M.S Stabiliser Stand near panel Board to keep stabiliser safe. 1 Job Rs.2,500.00 Rs.2,500.00

35 Renovation (Repairing and painting) of Attendent Cum Pump room & toilet. (As per sub Estimate no.- 31) 1 Job Rs.31,613.61 Rs.31,613.61

36 Renovation (Repairing and painting) of Existing Boundry wall of Length 29Mtr and height 1.5Mtr. all complete as per direction of E/I. (As per sub Estimate no.- 32) 1 per meter Rs.1,733.82 Rs.1,733.82

37 Campus development by land filling and brick soaling. (As per sub Est.no.-33) 1 Job Rs.27,302.80 Rs.27,302.80

38 Replacement of Existing Solar driven Pump with Electric driven single phase 2 H.P. submersible pump set having discharging capacity 3 lps at a total head of 45meter (approx) of KSB/ Kirloskar or equivalent make with all accessories & fittings etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & commissioning as per standards specifications and direction of E/I. (As per sub Est. no.- 34) 1 Job Rs.88500.00 Rs.88,500.00

39 Supplying, installation Testing & commissioning of Solar Pannel plate etc all complete as per direction of E/I. (As per sub Est. no.- 35) 1 Job Rs.15,750.00 Rs.15,750.00

40 Supplying, installation Testing & commissioning of Variable Frequency Drive (VFD), Change over Switch and Net Energy Metering (NEM) system (As per sub Est. no.- 36) 1 Job Rs.60,450.00 Rs.60,450.00

41 Providing and Fixing 12 VOLT Solar Battery as per direction of E/I. (As per sub Est. no.- 37) 1 Job Rs.35,000.00 Rs.35,000.00

42 Providing all labours, tools and materials to repair the leakage of different sizes of pipe al different places including earthwork in excavation, opening of joint, dewatering of the trenches, making lead caulked joint & back filling the trenches etc. all complete work (As per sub Est. no.- 38)

(i) without road cutting 1 Nos. Rs.820.00 Rs.820.00

(ii) with Pucca road cutting 1 Nos. Rs.2,006.73 Rs.2,006.73

(i) without road cutting 1 Nos. Rs.890.00 Rs.890.00

(ii) with Pucca road cutting 1 Nos. Rs.2,076.73 Rs.2,076.73

(i) without road cutting 1 Nos. Rs.1,180.00 Rs.1,180.00

(ii) with Pucca road cutting 1 Nos. Rs.2,366.73 Rs.2,366.73

(i) without road cutting 1 Nos. Rs.1,250.00 Rs.1,250.00

(ii) with Pucca road cutting 1 Nos. Rs.2,436.73 Rs.2,436.73

43 Repairing of 63/25 kva transformer inclusing LT pannel rapair in pump house Including Conductor,fuse relay,Timer as required,ST- CTBT pannel repair,Transformer Oil ( 630Ltr) Make-Servo etc all complete as per direction of engineer in charge. 1 Nos. Rs.12,000.00 Rs.12,000.00

44 Providing all labours, materials and cleaning of RCC water VAT from inside and doing chlorination etc. all complete work as per specification & direction of E/I. (As per sub Est. no.- 39) 1 Nos. Rs.1,053.60 Rs.1,053.60

45 Construction of 200 mm x 150 mm x 125 m deep T/W etc. with UPVC Pipe all complete and as per direction of E/I. (as per sub-estimate no.40). 1 Nos. Rs.361,106.00 Rs.361,106.00

46 Construction of 200 mm x 150 mm x 125 m deep T/W etc. with MS Pipe all complete and as per direction of E/I. (as per sub-estimate no.41). 1 Nos. Rs.474,807.00 Rs.474,807.00

47 Construction of 300 mm x 200 mm x 125 m deep T/W etc. with MS Pipe all complete and as per direction of E/I. (as per sub-estimate no.42). 1 Nos. Rs.727,318.15 Rs.727,318.15

48 Construction of 450 mm x 300 mm x 125 m deep T/W etc. with MS Pipe all complete and as per direction of E/I. (as per sub-estimate no.43). 1 Nos. Rs.1,390,348.00 Rs.1,390,348.00

Painting of 10000 Gallon Water Tower. (as per sub-estimate no.44). 1 Nos. Rs.164,266.00 Rs.164,266.00

Painting of 20000 Gallon Water Tower. (as per sub-estimate no.45). 1 Nos. Rs.179,058.00 Rs.179,058.00

Painting of 40000 Gallon Water Tower. (as per sub-estimate no.46). 1 Nos. Rs.243,020.00 Rs.243,020.00

Painting of 50000 Gallon Water Tower (as per sub-estimate no.47). 1 Nos. Rs.312,122.00 Rs.312,122.00

49 Provision of pump operator 1 Nos. Rs.4,000.00 Rs.4,000.00

50 Payment of electricity bills as per actual electricity bills.

BoQ (Fixed Cost)

I. Fixed Costs (WLS (Q/NQ))

(a) Cost of pump operator

1 nos for 365 days per month 48000 12.00 4000.00 48000.00

Sub Total a= 48000.00

(b) Cost of energy charges

Capacity of motor pump say 17.50 HP=(.746x17.5=13.055 kW) kW 2.24

Avg. running hrs,/day 8

Energy charges per year= avg. running hrs/dayx.746x17.5x365 per unit 6534.96 2.6 16990.896

fixed charges per month 12 100.00 3600.00

duty charges @6% of energy charge 1019.45

SubTotal b= 21610.35

Total Fixed Cost (I) = 69,610.35

Contractor's profit @ 10% on (II)= 11,761.03

Add GST @ 18% on ( II)= 2,116.99

Total Cost (I) 83,488.37

Bill of Quantity 2 (Variable Cost)

1 WATER SUPPLY: DUCTILE IRON (DI) SPECIALS

1.1 Providing Ductile Iron Push on special confirming to IS 9523:2000

1.1.1 100mm diameter 11.25⁰ Each 1366.00

1.1.2 100mm diameter 22.50⁰ Each 1464.00

1.1.3 100mm diameter 45⁰ Each 2064.00

1.1.4 100mm diameter 90⁰ Each 1817.00

1.1.5 150mm diameter 11.25⁰ Each 2148.00

1.1.6 150mm diameter 22.50⁰ Each 2207.00

1.1.7 150mm diameter 45⁰ Each 2480.00

1.1.8 150mm diameter 90⁰ Each 3145.00

1.1.9 200mm diameter 11.25⁰ Each 3232.00

1.1.10 200mm diameter 22.50⁰ Each 3396.00

1.1.11 200mm diameter 45⁰ Each 4172.00

1.1.12 200mm diameter 90⁰ Each 5369.00

1.1.13 250mm diameter 11.25⁰ Each 4235.00

1.1.14 250mm diameter 22.50⁰ Each 4622.00

1.1.15 250mm diameter 45⁰ Each 5706.00

1.1.16 250mm diameter 90⁰ Each 7465.00

1.1.17 300mm diameter 11.25⁰ Each 5932.00

1.1.18 300mm diameter 22.50⁰ Each 7077.00

1.1.19 300mm diameter 45⁰ Each 8673.00

1.1.20 300mm diameter 90⁰ Each 11217.00

1.1.21 350mm diameter 11.25⁰ Each 7801.00

1.1.22 350mm diameter 22.50⁰ Each 9197.00

1.1.23 350mm diameter 45⁰ Each 11701.00

1.1.24 350mm diameter 90⁰ Each 16627.00

1.1.25 400mm diameter 11.25⁰ Each 11195.00

1.1.26 400mm diameter 22.50⁰ Each 12825.00

1.2 Providing Ductile Iron(DI) push on specials confirming to IS 9523:2000

1.2.1 400mm diameter 45⁰ Each 16224.00

1.2.2 400mm diameter 90⁰ Each 22716.00

1.2.3 450mm diameter 11.25⁰ Each 13998.00

1.2.4 450mm diameter 22.50⁰ Each 15967.00

1.2.5 450mm diameter 45⁰ Each 20976.00

1.2.6 450mm diameter 90⁰ Each 28788.00

1.2.7 500mm diameter 11.25⁰ Each 16939.00

1.2.8 500mm diameter 22.50⁰ Each 20568.00

1.2.9 500mm diameter 45⁰ Each 28165.00

1.2.10 500mm diameter 90⁰ Each 39127.00

1.2.11 600mm diameter 11.25⁰ Each 25143.00

1.2.12 600mm diameter 22.50⁰ Each 31833.00

1.2.13 600mm diameter 45⁰ Each 41729.00

1.2.14 600mm diameter 90⁰ Each 60864.00

1.3 Providing Ductile Iron push on specials confirming to IS 9523:2000 socketed DI equal tees

1.4 Providing Ductile Iron push on specials confirming to IS 9523:2000 double socketed with flanged branch DI unequal Tees

1.5 Providing Ductile Iron push on specials confirming to IS 9523:2000 all socketed DI unequal Tees

1.6 Providing Ductile Iron push on specials confirming to IS 9523:2000 all socketed DI reducers/tapers

1.7 Providing Ductile Iron push on specials confirming to IS 9523:2000 all DI flanged socketed, DI flanged spigot, MS end plates

1.7.1 D.I. flanged socketed

1.7.2 D.I. flanged socketed 100 mm Each 1543.00

1.7.3 D.I. flanged socketed 150 mm Each 2499.00

1.7.4 D.I. flanged socketed 200 mm Each 3374.00

1.7.5 D.I. flanged socketed 250 mm Each 4978.00

1.7.6 D.I. flanged socketed 300 mm Each 6179.00

1.7.7 D.I. flanged socketed 350 mm Each 8882.00

1.7.8 D.I. flanged socketed 400 mm Each 10778.00

1.8 Providing Ductile Iron push on specials confirming to IS 9523:2000 all DI flanged MJ collar

2 Water supply works

2.1 Removing the GI pipes, cleaning, washing and using at spot or conveying from work site to office/store with all lead and lift i/c removal of all items such as collars, elbows, tees, bends etc,

2.2 Labour charges for laying and jointing GI pipes with earthwork i/c collars, elbows, tees, bends etc. with cuts and threads, white lead paint, conveying the material from store to work site and returning the surplus at store

2.2.1 15mm dia. GI m 10.00

2.2.2 20mm dia. GI m 13.00

2.2.3 25mm dia. GI m 19.00

2.2.4 40mm dia. GI m 24.00

2.2.5 50mm dia. GI m 32.00

2.2.6 65mm dia. GI m 32.00

2.2.7 80mm dia. GI m 32.00

2.3 Cutting charges for CI/DI pipes laid in the ground with necessary tools

2.3.1 100mm dia pipes Each 75.00

2.3.2 125mm dia pipes Each 79.00

2.3.3 150mm dia pipes Each 83.00

2.3.4 175mm dia pipes Each 92.00

2.3.5 200mm dia pipes Each 117.00

2.3.6 225mm dia pipes Each 125.00

2.3.7 250mm dia pipes Each 167.00

2.3.8 300mm dia pipes Each 208.00

2.3.9 375mm dia pipes Each 229.00

2.3.10 400mm dia pipes Each 250.00

2.4 Making cemenr mortar (1:1) and hemp yarn joint for CI pipes i/c cost of all materials viz. cement, sand, hemp, curing for 10 days complete

2.5 Removing CI/DI valves and its tail piece from the pipeline, cleaning, washing, painting and returning the same at store

2.5.1 50mm dia. Each 148.00

2.5.2 80mm dia. Each 250.00

2.5.3 100mm dia. Each 265.00

2.5.4 125mm dia. Each 267.00

2.5.5 150mm dia. Each 339.00

2.5.6 175mm dia. Each 353.00

2.5.7 200mm dia. Each 473.00

2.5.8 225mm dia. Each 491.00

2.5.9 250mm dia. Each 691.00

2.5.10 300mm dia. Each 819.00

2.5.11 375mm dia. Each 828.00

2.5.12 400mm dia. Each 1166.00

2.6 Removing and cleaning CI/DI pipes and specials i/c jointing materials, washing (excluding valves)

2.7 Conveying CI/DI pipes and specials through transportation vehicles

2.7.1 upto 5km i/c loading and unloading qnt 150.00

2.7.2 upto 5km to 10 km excluding loading and unloading qnt 26.00

2.7.3 beyond 10km excluding loading and unloading qnt 16.00

2.8 Fixing DI/CI specials of mechanical jointing of different sizes after setting into the pipeline i/c cleaning, inserting rubber gasket, tightening with bolts & nuts i/c hire charges for T&P, appurtenances and lifting equipments

2.17.1 100mm to 200mm dia. dia. Each 46.00

2.17.2 250mm to 400mm dia. dia. Each 76.00

2.9 Providing and fixing DI Resilient seated soft sealing SLUICE VALVE of variouis dia. with body bonnet of Ductile Iron (DI) conforming ti IS-1865 with the latest amendments and of grade GGG 40/50, shaft of stainless steel, wedge fully rubber lined with EDPM seals of NBR and the valves should be vacum tight and 100% leak proof with face to face dimensions as per IS 14846-2000 with the latest amendments only. The stem sealing should be with toroidal sealing rings (minimum 2 " O " rings). Body and bonnet should be coated with Electrostatically applied Epoxy Powder Coating with minimum coating thickness of 250 micron both inside and outside. The rate is inclusive of cost of valves, T.P set, galvanized bolts & nuts and rubber insertions etc. but excluding earth work. For PN-10: (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate.) etc. complete

2.9.1 For sluice Valve of 50mm Each 5535.00

2.9.2 For sluice Valve of 80mm Each 10393.00

2.9.3 For sluice Valve of 100mm Each 10884.00

2.9.4 For sluice Valve of 150mm Each 17490.00

2.9.5 For sluice Valve of 200mm Each 28709.00

2.9.6 For sluice Valve of 250mm Each 46491.00

2.9.7 For sluice Valve of 300mm Each 60325.00

2.9.8 For sluice Valve of 350mm Each 93233.00

2.9.9 For sluice Valve of 400mm Each 125367.00

2.10 Providing and fixing Wafer type single flange Butterfly valve conforming to relevant IS 13099/9991 EN GGG40/50 with latest amendments as detailed below of the following diameter and types with TP set and conveying to work site, loading and unloading, stacking etc. with all lead and lift. The rate is inclusive of the cost of valve, TP set, rubber insertion, bolts and nuts and excluding earth work excavation.For PN 10.0 (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate.

2.10.1 For sluice Valve of 100mm Each 5849.00

2.10.2 For sluice Valve of 150mm Each 12553.00

2.10.3 For sluice Valve of 200mm Each 13971.00

2.10.4 For sluice Valve of 250mm Each 15374.00

2.10.5 For sluice Valve of 300mm Each 17346.00

2.10.6 For sluice Valve of 350mm Each 23477.00

2.10.7 For sluice Valve of 400mm Each 33092.00

2.11 Providing and fixing of Double Flanged Resilient seated short body Butterfly valves of various dis. As per IS 13095/en 593 with integral DI seat face with approved soft sealing with body and disc of Ductile Iron (DI) of grade GGG-40/50, Body seat & Seal retaining ring of SS 304/CF8, Shaft of stainless steel AISI 410/420/431, Bronze shaft bearing, periferal disk, seal end "o" rings of EPDM, double eccentric disk. Body and disk should be coated with electrostatcially applied epoxy powder coating with a coating thickness of 250 micron both inside and out side. The rate is inclusive of cost of valve, TP set, galvanised bolts and nuts and rubber insertions. For PN 10.0 (All the drilled holes in the body shall be of through holes, no tapped holes will be allowed.) (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate.) etc. complete

2.11.1 For Valve of PN 10.0 and 700mm Each 184739.00

2.11.2 For Valve of PN 10.0 and 750mm Each 239773.00

2.11.3 For Valve of PN 10.0 and 800mm Each 265385.00

2.11.4 For Valve of PN 10.0 and 900mm Each 313821.00

2.11.5 For Valve of PN 10.0 and 1000mm Each 407895.00

2.12 Providing & Fixing sluice valves/ Butterfly Valves (labour charges only) conforming to relevant ISS with latest amendments as detailed below for the following diameter and types with two Each of MJ collars, two flanged spigots, conveying to work site, loading, unloading, stacking with appurtenances. with all lead and lifts, aligning, fixing and testing with appurtenances. etc. complete.

2.1.2.1 For sluice valve with accessories - 50mm dia. Each 341.00

2.1.2.2 For sluice valve with accessories - 80mm dia. Each 381.00

2.1.2.3 For sluice valve with accessories - 100mm dia. Each 463.00

2.1.2.4 For sluice valve with accessories - 150mm dia. Each 524.00

2.1.2.5 For sluice valve with accessories - 200mm dia. Each 769.00

2.1.2.6 For sluice valve with accessories - 250mm dia. Each 1167.00

2.1.2.7 For sluice valve with accessories - 300mm dia. Each 1262.00

2.13 Providing and fixing DI MJ specials such as branches and bends suitable for DI K7 and K9 pipes and CI LA class pipes, as per IS 13382 with latest amendments with complete accessories and fixing at site excluding earth work but including loading, unloading, freight charges etc. complete for:

2.13.1 DI MJ specials - Branch 100 x 100mm Each 1701.00

2.13.2 DI MJ specials - Branch 150 x 150mm Each 2673.00

2.38.3 DI MJ specials - Branch 150 x 100mm Each 2322.00

2.38.4 DI MJ specials - Bend 100 x 90 degree mm Each 1203.00

2.38.5 DI MJ specials - Bend 100 x 45 degree Each 1174.00

2.38.6 DI MJ specials - Bend 150 x 90 degree Each 2322.00

2.38.7 DI MJ specials - collar 100mm dia. Each 2287.00

2.38.8 DI MJ specials - collar 150mm dia. Each 4102.00

2.14 Providing, fabricating and fixing at site various diameter MS MJ ends with dummy plates (END CAPS) to suit CI / DI spigots end as per the sketch. The cost is inclusive of all materials, i.e, rubber 'O' rings, flanges, bolts and nuts, dummy plates, consumables, hire charges, tools and welding equipments, lead and lifts, etc. complete as per the instructions of Engineer in charge.

2.14.1 For CI / DI pipes of 100mm dia. Each 1158.00

2.14.2 For CI / DI pipes of 150mm dia. Each 1609.00

2.14.3 For CI / DI pipes of 200mm dia. Each 2226.00

2.14.4 For CI / DI pipes of 250mm dia. Each 3213.00

2.14.5 For CI / DI pipes of 300mm dia. Each 3230.00

2.14.6 For CI / DI pipes of 400mm dia. Each 5077.00

2.15 Providing and fixing of Extension spindle rods,PN 10 /16 suitable for Gate valve of following dia for open and closing application, Extension Spindle lengths shall be available on required sizes as per site conditions, spindle shall be of fixed type, suitable size of MS Square bar epoxy coated, bottom adaptor & Spindle cap (epoxy coated /galvanised) ductile iron Gr40. Protection tube of PVC, Top and Bottom cover / Bottom Connector shall be made by PVC, Bolt shall be made by Zinc coated steel 8.8 Split pin shall be made by Electro galvanized, this set up should help to have a buried application of Gate Valves etc. complete as per the directions of the Engineer-in-Charge.

2.16 Providing & fixing RCC Pre-cast Cover Slab of size 0.8 m x 0.8 m x 0.15m of M25-Design mix concrete with 12 mm steel @ 120 mm c/c both ways, over Gate valve extension spindle with central opening along with lid for smooth operation with appurtenances., complete with all lead and lifts etc. complete Each 2386.00

2.17 Conveying with all lead & lift and fixing C.I/D.I specials, bends, branches, tees,with appurtenances, all sizes and aligning.

2.17.1 50 mm dia to 100 mm dia Each 105.00

2.17.2 125 mm dia to 225 mm dia Each 131.00

2.17.3 250 mm dia to 600 mm dia Each 203.00

3 Attendind leakages

3.1 Providing & fixing CI/DI pipes socket leak repair MJ clamps for attending to leak joints in socket / spigot joints of CI / DI pipes with necessary earth work excavation including using of pneumatic breakers and JCB excavator wherever required and providing DI MJ leak repair clamp, including cost of all materials required for jointing comprising of DI MJ clamps and its accessories such as rubber gaskets made of SBR / EPDM on the socket face, making the socket / spigot joint water tight at the operating pressure, backfilling with available earth and consolidation and bailing out water wherever necessary etc. complete and In all types of road surfaces like Concrete, Asphalt roads etc, for:

3.1.1 CI / DI pipes of 100mm dia. Each 2357.00

3.1.2 CI / DI pipes of 150mm dia. Each 3563.00

3.1.3 CI / DI pipes of 200mm dia. Each 4032.00

3.1.4 CI / DI pipes of 250mm dia. Each 5255.00

3.1.5 CI / DI pipes of 300mm dia. Each 6426.00

3.1.6 CI / DI pipes of 400mm dia. Each 9059.00

3.1.7 CI / DI pipes of 450mm dia. Each 11257.00

3.2 Attending to leaking socket / spigots joints in CI / DI pipes in all types of road surfaces including concrete and asphalt roads, with necessary earth work excavation including using of pneumatic breakers and JCB excavator wherever required for jointing DI MJ clamp and its accessories such as rubber gaskets made of SBR / EPDM on the socket face, making the socket / spigot joint water tight at the operating pressure, backfilling with available earth and consolidation and bailing out water wherever necessary etc.complete.

3.2.1 For CI / DI pipes of 100mm dia. Each 722.00

3.2.2 For CI / DI pipes of 150mm dia. Each 814.00

3.2.3 For CI / DI pipes of 200mm dia. Each 820.00

3.2.4 For CI / DI pipes of 250mm dia. Each 954.00

3.2.5 For CI / DI pipes of 300mm dia. Each 1254.00

3.2.6 For CI / DI pipes of 400mm dia. Each 1289.00

3.2.7 For CI / DI pipes of 450mm dia. Each 1406.00

3.3 Cutting Asphalt /Concrete road surface using machine cutter for leakage pit with earth work excavation in all classifications of soil including all lead and lifts bailing out water with pumps including barricading, danger lighting etc., as per requirement and disposing of the excavated stuff as directed. After attending the leak, refilling the trench for 30 cm depth quarry dust above and around pipelines and balance with available earth in layers not exceeding 20 cms in depth, compacting Each deposited layer by ramming including watering and consolidation by mechanical means approved by Engineer Incharge. (Work to be carried out as per leak repair manual and the rate includes hire charges of dewatering Pump, tractor, Jeep with all kinds of Labour in a Complete manner). m3 1157 m2 1157.00

3.4 Road Reinstatement of Asphalt /Concrete roads after leak attending with earth work excavation of compacted soil depositing on bank with all lead and lifts including danger lighting and barricading. Providing, laying, spreading and compacting graded stones aggregate as per wet mix macadam specifications. Applying tack coat on granular base such as WBM and WMM surface hot bitumen primer at 4 kg per 10 sqm, heating bitumen in layer to be laid with boiler fitted with spray set of 300 mm thickness. Above laid with bituminous concrete or M20 concrete premixed with bituminous binder at 5.4 to 5.6% of mix and filler, to achieve the desired compaction to give minimum of 45mm thickness compacted. The work shall be carried as per leak repair manual and includes all kinds of materials disposing off the excess excavated Earth with all lead and lifts by vehicle including loading, unloading, labour, HOM of machinery etc. in a complete manner. m2 1690.00

4.1 Providing and laying Ductile Iron pipes of class conforming to IS 8329:2000 with latest amendments, conveying to work site, rolling and lowering into trenches, laying true to line, level and perfect linking at joints, testing and commissioning, including loading and unloading at both destinations, cutting of pipes wherever necessary, jointing with DI specials (excluding cost of specials) and rubber gaskets, cleaning the socket and spigot end with soap solution, applying soft soap to the socket and spigot ends before insertion of rubber gaskets, jacking and fixing in perfect conditions etc. The cost to include soap solution, soft soap, waste etc. and giving necessary hydraulic test to the required pressure as per ISS with all lead and lifts and cost of all jointing materials. (The contractor will make his own arrangements for water for testing. Earth work excavation in trenches to be measured and paid for seperately) Note: In sewerage projects for internal cement mortal lining ( CML ) of DI pipes, if High Alumina Cement ( HAC ) as recommended in Annexure B clause 16.3 of IS8329:2000 is considered in place of Slag or Sulphate Resistance Cement ( SRC ), the cost of pipes may be increased by 5-6% from the prices listed. For DI K7 pipes:

4.1.1 100mm dia pipe m 1460.00

4.1.2 150mm dia pipe m 2016.00

4.1.3 200mm dia pipe m 2576.00

4.1.4 250mm dia pipe m 3140.00

4.1.5 300mm dia pipe m 3968.00

4.1.6 350mm dia pipe m 4999.00

4.1.7 400mm dia pipe m 5976.00

4.2 Labour charges for laying & jointing of DI pipes of all classes rolling and lowering into trenches, laying true to line, level and perfect linking at joints and commissioning, including loading and unloading at both destinations and cuts of pipes wherever necessary including jointing of DI pipes and specials (excluding cost of pipes,rubber gasket and specials) with rubber gaskets including cleaning the sockets and spigot ends with saop solutions and applying soft soap to the spigot and socket end before insertion of rubber gaskets, jointing and fixing in perfect conditions including the cost of soap solution, soft soap, waste etc. and giving necessary hydraulic test to the required pressure as per ISS etc. with all leads and lifts (Earth work excavation in trenches,conveying of materials from stores to be measured and paid for separately) (Contractor will make his own arrangements for procuring water for testing) etc. complete for:

4.2.1 100mm dia pipe m 72.00

4.2.2 150mm dia pipe m 103.00

4.2.3 200mm dia pipe m 150.00

4.2.4 250mm dia pipe m 261.00

4.2.5 300mm dia pipe m 311.00

4.2.6 350mm dia pipe m 339.00

4.2.7 400mm dia pipe m 378.00

4.5 Labour charges for making flanged joints including cost of jointing materials comprising of rubber insertion, galvanised bolts and nuts including giving hydraulic test to the required pressure as per ISS with all lead & lift (contractor will make his own arrangement for procuring water for testing) etc. complete

4.5.1 Pipes and specials of dia 50mm. Each 113.00

4.5.2 Pipes and specials of dia 80mm. Each 124.00

4.5.3 Pipes and specials of dia 100mm. Each 208.00

4.5.4 Pipes and specials of dia 150mm. Each 310.00

4.5.5 Pipes and specials of dia 200mm. Each 334.00

4.5.6 Pipes and specials of dia 250mm. Each 498.00

4.5.7 Pipes and specials of dia 300mm. Each 520.00

4.5.8 Pipes and specials of dia 350mm. Each 707.00

4.5.9 Pipes and specials of dia 400mm. Each 1033.00

4.6 Providing RUBBER JOINTING for CI / DI pipes with rubber gaskets including cleaning the socket and spigot ends with soap solution and applying soft soap to the spigot and socket ends before insertion of rubber gaskets, jacking and fixing in perfect conditions including cost of soap solution, soft soap, waste etc with all lead and lift including cost of jointing materials etc.complete for:

5 RCC Overhead tanks

7.1 Providing and fixing MS ladder between landings, 45 cms wide using angle iron of specified sizes, 20mm MS bars at 25 cms. centre to centre, with necessary supports of same angle iron etc. as directed, including hand railing on both sides with 25mm dia. GI pipes with angle iron props at 2 mtrs. intervals and 0.5M heigh, including fixing in ground with CC 1:2:4 and two coats of anticorrosive bituminous paint etc. with all lead and lifts etc. complete with:

7.1.1 MS angle of 65 x 65 x 8mm m 4377.00

7.1.2 MS angle of 65 x 65 x 10mm m 4801.00

7.6 Providing, Laying and Jointing Cast Iron (CI) double flanged pipes true to line / hoisting of DI flanged pipe in position and aligning to correct plumb, including cost of jointing materials, conveying to work spot with all lead and lifts etc.complete.

7.6.1 For double flanged CI pipes of 80mm dia. m 2245.00

7.6.2 For double flanged CI pipes of 100mm dia. m 3010.00

7.6.3 For double flanged CI pipes of 150mm dia. m 4808.00

7.6.4 For double flanged CI pipes of 200mm dia. m 6592.00

7.6.5 For double flanged CI pipes of 250mm dia. m 9272.00

7.7 Providing and fixing lightening arrestor with aluminium strip 25mm x 3mm size including finial and grounding, aluminium strip to be embeded in one of the columns in and independent GI conduit of 40mm dia. pipe suitably jointed by collars with all specials with all lead and lifts etc. complete for:

7.7.1 For Over Head Tanks upto 6 M staging Each 8088.00

7.7.2 For Over Head Tanks upto 9 M staging Each 9387.00

7.7.3 For Over Head Tanks upto 12M staging Each 11530.00

7.7.4 For Over Head Tanks above 12M staging Each 13889.00

7.9 Providing, of DI flanged pipe conforming to IS 8329 : 2000 with latest amendments with Cement Mortar Lining (CML) with Portland Slag Cement as per IS 455:1989 and Metallic Zinc Coating as per annexure A of IS 8329 with finishing layer of Bituminous Coating as per Annexure C of IS 8329 and Flanges: Metallic zinc rich epoxy paint & Bituminous Coating, laying true to line and hoisting in position and aligning to correct plumb including cost of jointing material, conveying to work spot with all lead and lifts etc., complete. For PN 10.0

7.11 Providing Ductile Iron Push on special confirming to IS 9523:2000 - All Double Socket Duck Foot DI Bends:

8.2 Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to RCC structures like floor and walls of reservoirs, sewe, effluent and water treatment plants, over head tanks, etc. prepared by mixing in the ratio of 5:2 (5 parts integral crystalline slurry 2 parts water) for horizontal and vertical surfaces and applying the same from negative (internal) side with the help of synthetic fibre brush. The material shall meet the requirements as specified in ACI - 212-3R-2010 ie. by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 Bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self healing of cracks upto a width of 0.50 mm. The work shall be carried out all complete as per specification and the direction of the Engineer in charge. The product performance shall carry guarantee for 10 years against any leakage. For horizontal and vertical surfaces in two coats @ 0.70 kg per sqm per coat m2 433.00

9.15 Lowering and laying and fusion welding Jointing for HDPE Pipes Grade PE- 80 / PE-100 conforming to IS 4984-2016, of specified dia. including hydrualic testing and commissioning etc.(Contractor will make his own arrangements for procuring water for testing) for:

11.1 Providing, Laying and Fixing of GI pipes conforming to IS 1239:1990 with latest amendments complete with GI fittings (excluding the cost of fittings) with cuts and threads wherever necessary, including testing for water tightness, with all lead and commissioning. (contractor will make his own arrangements for procuring water for testing) For:Heavy Duty GI Pipe etc. complete.

11.2 For Medium Duty GI pipe:

11.2.6 Medium Duty GI pipe of 50mm dia m 584.00

11.2.7 Medium Duty GI pipe of 65mm dia m 719.00

11.2.8 Medium Duty GI pipe of 80mm dia m 891.00

11.2.9 Medium Duty GI pipe of 100mm dia m 1245.00

11.3 For Heavy Duty GI pipe:

11.3.6 Heavy Duty GI pipe of 50mm dia m 679.00

11.3.7 Heavy Duty GI pipe of 65mm dia m 834.00

11.3.8 Heavy Duty GI pipe of 80mm dia m 1009.00

11.3.9 Heavy Duty GI pipe of 100mm dia m 1412.00

11.4 Providing and fixing GI union in existing GI pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required etc. complete for:

11.4.6 20.88.6: 50 mm nominal bore Each 660.00

11.4.7 20.88.7: 65 mm nominal bore Each 878.00

11.4.8 20.88.8: 80 mm nominal bore Each 1041.00

11.5 Providing lead caulked joints to spun iron or CI pipes and specials with spun yarn and lead, including caulking and giving satisfactory hydraulic test corresponding to the required pressure etc. complete.for:

11.5.1 Spun / CI / DI pipes 80MM Each 481.00

11.5.2 Spun / CI / DI pipes 100MM Each 500.00

11.5.3 Spun / CI / DI pipes 150MM Each 747.00

11.5.4 Spun / CI / DI pipes 200MM Each 944.00

11.5.5 Spun / CI / DI pipes 250MM Each 1210.00

11.5.6 Spun / CI / DI pipes 300MM Each 1425.00

11.6 Providing wrought mild steel (galvanized) GI collar confirming to IS 1239-II, 1991 with latest amendments if any.

11.6.6 For 50 mm dia GI collar: Each 267.00

11.6.7 For 65 mm dia GI collar: Each 312.00

11.6.8 For 80 mm dia GI collar: Each 421.00

11.6.9 For 100 mm dia GI collar: Each 505.00

11.6.10 For 125 mm dia GI collar: Each 636.00

11.6.11 For 150 mm dia GI collar: Each 695.00

11.7 Supply and delivery at site wrought middle steel (galvanized) GI elbow confirming to IS 1239-II, 1991 with latest amendments if any for:

11.7.6 For 50 mm dia GI elbow Each 267.00

11.7.7 For 65 mm dia GI elbow Each 297.00

11.7.8 For 80 mm dia GI elbow Each 417.00

11.7.9 For 100 mm dia GI elbow Each 490.00

11.7.10 For 125 mm dia GI elbow Each 578.00

11.7.11 For 150 mm dia GI elbow Each 651.00

11.8 Supply and delivery at site wrought middle steel (galvanized) GI bend confirming to IS 1239-II, 1991 with latest amendments if any.

11.8.6 For 50 mm dia GI BEND Each 358.00

11.8.7 For 65 mm dia GI BEND Each 404.00

11.8.8 For 80 mm dia GI BEND Each 490.00

11.8.9 For 100 mm dia GI BEND Each 600.00

11.8.10 For 125 mm dia GI BEND Each 680.00

11.8.11 For 150 mm dia GI BEND Each 724.00

11.9 Supply and delivery at site wrought middle steel (galvanized) GI tee confirming to IS 1239-II, 1991 with latest amendments if any.

11.9.6 For 50 mm dia GI TEE Each 297.00

11.9.7 For 65 mm dia GI TEE Each 373.00

11.9.8 For 80 mm dia GI TEE Each 434.00

11.9.9 For 100 mm dia GI TEE Each 607.00

11.9.10 For 125 mm dia GI TEE Each 775.00

11.9.11 For 150 mm dia GI TEE Each 914.00

11.1 Supply and delivery at site wrought middle steel (galvanized) GI socket confirming to IS 1239-II, 1991 with latest amendments if any.

11.10.6 For 50 mm dia GI socket Each 297.00

11.10.7 For 65 mm dia GI socket Each 373.00

11.10.8 For 80 mm dia GI socket Each 454.00

11.10.9 For 100 mm dia GI socket Each 563.00

11.10.10 For 125 mm dia GI socket Each 614.00

11.10.11 For 150 mm dia GI socket Each 731.00

11.11 Supply and delivery at site wrought middle steel (galvanized) GI plugs confirming to IS 1239-II, 1991 with latest amendments if any.

11.11.6 For 50 mm dia GI Plugs Each 199.00

11.11.7 For 65 mm dia GI Plugs Each 237.00

11.11.8 For 80 mm dia GI Plugs Each 256.00

11.11.9 For 100 mm dia GI Plugs Each 358.00

11.11.10 For 125 mm dia GI Plugs Each 432.00

11.11.11 For 150 mm dia GI Plugs Each 490.00

11.12 Supply and delivery at site wrought middle steel (galvanized) GI union confirming to IS 1239-II, 1991 with latest amendments if any.

11.12.6 For 50 mm dia GI Union Each 267.00

11.12.7 For 65 mm dia GI Union Each 351.00

11.12.8 For 80 mm dia GI Union Each 578.00

11.12.9 For 100 mm dia GI Union Each 622.00

11.12.10 For 125 mm dia GI Union Each 666.00

11.12.11 For 150 mm dia GI Union Each 783.00

11.2 Lowering, Laying and Jointing GI pipes conforming to IS 1239:1990 with latest amendments complete with GI fittings (excluding the cost of fittings) with cuts and threads wherever necessary, including testing for water tightness, with all lead and commissioning. (contractor will make his own arrangements for procuring water for testing) for etc. complete.

Bill of Quantity 3 (Variable Cost)

13 SUBMERSIBLE PUMPSETS AND REPLACEMENT OF PARTS

13.1 Rewinding of submersible pumpset with copper winding wires of appropriate guage, as per specifications and / or directions of the departmental officials, including all materials, labour, equipment and testing. for all types of submersible pumpsets etc.(with guarantee period not less than 6 months) for

13.1.1 For all types of submersible pumpsets upto 3.0 H.P. Each 2710.00

13.1.2 above 3 HP and upto 5.0 H.P. Each 2934.00

13.1.3 above 5.0 HP and upto 5.5H.P. Each 3116.00

13.1.4 above 5.5 HP and upto 6.0H.P. Each 3296.00

13.1.5 above 6.0 HP and upto 6.5H.P. Each 3479.00

13.1.6 above 6.5 HP and upto 7.0H.P. Each 3659.00

13.1.7 above 7.0 HP and upto 7.5H.P. Each 3839.00

13.1.8 above 7.5 HP and upto 8.0H.P. Each 4019.00

13.1.9 above 8.0 HP and upto 8.5H.P. Each 4201.00

13.1.10 above 8.5 HP and upto 9.0H.P. Each 4382.00

13.1.11 above 9.0 HP and upto 9.5H.P. Each 4562.00

13.1.12 above 9.5 HP and upto 10.0H.P. Each 4744.00

13.1.13 above 10 HP and upto 11 H.P. Each 5157.00

13.1.14 above 11 HP and upto 12 H.P. Each 5570.00

13.1.15 above 12 HP and upto 13 H.P. Each 5983.00

13.1.16 above 13 HP and upto 14 H.P. Each 6397.00

13.1.17 above 14 HP and upto 15 H.P. Each 6811.00

13.2 Replace the components of submersible pump sets, requiring replacements decided by the departmental officials, with respective make of damaged ones, including all materials, labour, equipments and testing etc.(with gurantee of period not less than 1 year) for:

13.2.1 The bowls of same type and make Each 1500.00

13.2.2 The Intermediate piece (IP) with IP leaded bronze brush. Each 1050.00

13.2.3 The Oil Seal. Each 350.00

13.2.4 The Oil Seal.and steel bush Each 250.00

13.2.5 The Guide Vane Each 700.00

13.2.6 The Impeller (Shell moulded with aluminium and bronze.) Each 1500.00

13.2.7 The discharge outlet (DO) bearing DO steel brush DO bearing. Each 2050.00

13.2.8 The steel bearing bush (DO steel bush) Each 400.00

13.2.9 The allen screw Each 1200.00

13.2.10 The pump shaft made out of stainless steel counterless ground with key way (upto 8 stages). Extra for Each stage @ Rs.40/-. Each 1500.00

13.2.11 The pump key (stainless steel) Each 650.00

13.2.12 The pump coupling (stainless steel) Each 1500.00

13.2.13 The Non Return Valve (NRV) assembly complete with rubber 'O' ring. Each 650.00

13.2.14 The cable guard Each 350.00

13.2.15 The strainer Each 450.00

13.2.16 The brass filter Each 1050.00

13.2.17 The Labour Charges for overhauling of the pump set. Each 900.00

13.3 Replace the components of motor parts of submersible pump sets, items requiring replacements decided by the departmental officials, with respective make of damaged ones, including all materials, labour, equipments and testing etc and wtih guarantee/ warranty for one year for:

13.3.1 The STATOR of motor upto 3 H.P Each 1500.00

13.3.2 The STATOR of motor 3 to 4 H.P Each 2500.00

13.3.3 The STATOR of motor 4 to 5 H.P Each 3500.00

13.3.4 The ROTOR of motor upto 3.0 H.P Each 1200.00

13.3.5 The ROTOR of motor 3 to 4 H.P Each 1500.00

13.3.6 The ROTOR motor 4 to 5 H.P Each 2000.00

13.3.7 The upper flange Each 650.00

13.3.8 The lower flange Each 650.00

13.3.9 upper/ lower housing Each 1200.00

13.3.10 The Lock Ring Each 350.00

13.3.11 The Carbon Housing Each 2000.00

13.3.12 The Carbon Housing (Thrust bearing block assembly complete with segment bearing pad. Each 2200.00

13.3.13 The Carbon Housing (Top carbond / ferrodo padding) Each 350.00

13.3.14 The Stud and Nuts Each 200.00

13.3.15 The Gun Metal bearing, centrifugally cast Aluminium Bronze bearing Each 850.00

13.3.16 The Circlips Each 200.00

13.3.17 The Motor base with pin Each 500.00

13.3.18 The Transportation of pumping machineries Each 1200.00

13.3.19 The Re-errection charges of pumping machineries including overhauling Each 2000.00

13.3.20 The lifting of submersible pumpset from well. Each 1500.00

13.3.21 The Labour charges only for overhauling Each 3000.00

13.3.22 Providing of Thermosetting Plastic i.e., Fibere Glass reinforced polyster sheet moulding compound(SMC) pump house with SMC door & canopy etc...,complete component as directed by the departmental officers. Each 12000.00

13.4 Providing, Single Phase Submersible Pump Sets of 100mm dia (4 inch) suitable for bore well confirming to IS 8034-2000 specifications, to work site with testing of as per instructions of engineer incharge of work and latest amendments etc. complete.

13.4.1 0.50 HP/0.37kW - 5 STG(stage) Each 10170.00

13.4.2 0.50 HP/0.37kW - 7 STG(stage) Each 10855.00

13.5 For 0.75 HP/0.55KW

13.11 Providing Submersible Pump Set of 150mm dia suitable for bore well and confirming to IS 8034-2000;3Phase, SS Bowl & Impeller with Low volt Motor as per specifications, to work site as per necessary ammendments and instructions of engineer incharge of work. For 3 HP etc. complete.

13.11.1 3.00 HP - 300 LPM @ 26 m = 5 STG Outlet Dia - 2.50" Each 23168.00

13.11.2 3.00 HP - 155 LPM @ 42 m = 7 STG Outlet Dia - 2.00" Each 24334.00

13.11.3 3.00 HP - 135 LPM @ 56 m = 8 STG Outlet Dia - 2.00" Each 25910.00

13.11.4 3.00 HP - 120 LPM @ 55 m = 9 STG Outlet Dia - 2.00" Each 26627.00

13.11.5 3.00 HP - 90 LPM @ 66 m = 10 STG Outlet Dia - 2.00" Each 28113.00

13.12.1 4.00 HP - 360 LPM @ 30 m = 6 STG Outlet Dia - 3.00" Each 22628.00

13.12.2 4.00 HP - 245 LPM @ 42 m = 8 STG Outlet Dia - 2.50" Each 23319.00

13.12.3 4.00 HP - 155 LPM @ 56 m = 9 STG Outlet Dia - 2.00" Each 24107.00

13.12.4 4.00 HP - 135 LPM @ 70 m = 5 STG Outlet Dia - 2.00" Each 24993.00

13.12.6 4.00 HP - 90 LPM @ 88 m = 12 STG Outlet Dia - 2.00" Each 26730.00

13.13.1 5.00 HP - 300 LPM @ 39 m = 5 STG Outlet Dia - 2.50" Each 26310.00

13.13.2 5.00 HP - 245 LPM @ 56 m = 8 STG Outlet Dia - 2.50" Each 27010.00

13.14.1 6.50 HP - 360 LPM @ 45 m = 5 STG Outlet Dia - 3.00" Each 26930.00

13.14.2 6.50 HP - 300 LPM @ 52 m = 6 STG Outlet Dia - 2.50" Each 27813.00

13.14.3 6.50 HP - 245 LPM @ 70 m = 8 STG Outlet Dia - 2.50" Each 29930.00

13.15.1 7.50 HP - 360 LPM @ 60 m = 5 STG Outlet Dia - 3.00" Each 28116.00

13.15.2 7.50 HP - 300 LPM @ 65 m = 6 STG Outlet Dia - 2.50" Each 30010.00

13.15.3 7.50 HP - 245 LPM @ 84 m = 8 STG Outlet Dia - 2.50" Each 32819.00

13.22 Supply and delivery at site Brand new best make PVC insulated cable of Flat 3 core (sheathed) of nominal cross sectional area as per IS 694-1990 with ISI Mark and as per its latest amendments.

13.23 Supply and delivery at site of brand new best make pressure gauge bourdon type as per IS 778/1984 with ISI Mark and as per its latest amendments.

13.23.1 Size 63 mm Each 416.00

13.23.2 Size 80 mm Each 597.00

13.23.3 Size 100 mm Each 654.00

13.24 Supply and delivery at site of brand new best make gate valve as per IS 778/1984 with ISI Mark and as per its latest amendments

13.24.1 Size 50 mm Each 1250.00

13.24.2 Size 65 mm Each 1450.00

13.24.3 Size 80 mm Each 1650.00

13.25 Supply and delivery at site of brand new best make non-return valve as per IS 778/1984 with ISI Mark and as per its latest amendments

13.25.1 Size 50 mm Each 1250.00

13.25.2 Size 65 mm Each 1550.00

13.25.3 Size 80 mm Each 1750.00

13.23 Supply, installing,testing and commissioning COMMON control panel consisting of the following INCOMING:1 No set of Phase indicating lamps with SFU of suitable rating 1 No, Analog Ammeter, 1 No Analog Voltmeter 1ni with Phase selector switch, Isolating switch OUTGOING for Main Electrical Pump: 1 No. MCB 1 No. DOL of S/D Starter suitable for respective HP 1 No. Electrcal Protection Like single Phase preventor, under voltage over Volage, under current over current & dry run protection suitable for the pump described above 1 no Indoor type NOTE:

1) DOL- Direct Online Starter

2) S-D- Star Delta Starter etc. complete.

13.23.1 Upto 3 HP pumps Each 6500.00

13.23.2 3 to 6 HP pumps Each 9550.00

13.23.3 6 to 15 HP pumps Each 15900.00

13.24 for outdoor

13.24.1 Upto 3 HP pumps Each 7500.00

13.24.2 3 to 6 HP pumps Each 10500.00

13.24.3 6 to 15 HP pumps Each 17500.00

13.25 Supply and delivery at site best indigenous brand new power capacitor as per IS 2834/1986 with latest amendments with KPTCL authorities and erection, electrification and commissioning of the same at the location of respective pump sets. kVAR 550.00

13.26 Supply and delivery at site delivery of best indigenous brand new MCB (Miniature Circuit Breakers) of required capacity as per IS 88228/1978 and its latest amendments and with ISI Mark of 6/10/16/20/25/40 Amps with scalable box. per 3 poles 1150.00

13.27 Supply and delivery of galvanized mild steel tubes of 6mtr standard length heavy duty (C Class) as per IS 1239 (Part-I) 1990 with latest amendments with ISI Mark (one end fitted with Heavy Duty collar and other end fitted with protective cover)

13.28 Supply and delivery at site 50mm(2”) dia heavy duty unplasticized PVC Column pipes with heavy duty collars,rubber profile ring,vibration control profile ring,freezing and turbulence free leak proof EPDM ring with ISI mark with its latest amendments m 550.00

13.29 Supply and delivery at site 50mm(2”) dia heavy duty CI adopter set complete suitable for uPVC Column pipes for Submersible pumpsets SET 1550.00

13.3 Supply and delivery at site Accessories for Single Phase pumpset like SS Groove Nipples,SS Studs & Nuts,Screw Clips &water proof Insulation Tape etc complete with ISI mark SET 4500.00

13.31 Supply and delivery at site Stringing of heavy duty Naylone/PP rope with ISI etc complete suitable for Single phase Pumpsets. m 40.00

13.32 Labour charges for Erection, Electrification and commissioning of Pump sets, including aligning and balancing of all items including supply and erection of two pair of supporting clamps, bore well caps, cable clips and water tight gland cable protectors, bolts, nuts, valve and gauges,tools and equipments etc., involved in the job as per specifications, with necessary tests as per specifications, with testing of as per instructions of engineer incharge of work. Job 6500.00

13.33 Labour charges for erection of indoor type panel board and meter board units with all necessary materials and labour tools and equipments including cement concrete for foundation/bed etc,complete as per specification, with testing of as per instructions of engineer incharge of work. Job 1350.00

13.34 Labour charges for erection of outdoor type panel board and meter board units with all necessary materials and labour, tools and equipments including providing cement concrete foundation bed etc., complete as per specification, with testing of as per instructions of engineer incharge of work. Job 1450.00

13.35 Labour charges for providing connection using insulated sheathed steel wire cable as per IS 1554/ 1988 with latest amendments from KPTCL pole to meter board unit, with all necessary materials ,tools and equipments,as per specificationswith testing of as per instructions of engineer incharge of work. .

13.35.4 3 x 10 sqmm (suitable for over head mains) m 165.00

13.36 Providing main connection from pole PVC insulated sheathed steel wire cable in new trench as per IS 1554/ 1988 with latest amendments with ISI mark from KPTCL pole to meter board unit. m 135.00

13.37 Providing main connection from pole PVC insulated sheathed steel wire cable in GI pipe as per IS 1554/ 1988 with latest amendments with ISI mark from KPTCL pole to meter board unit. m 85.00

13.38 Providing and fixing suitable for 1.1 KV class UG cable filled with necessary bitumen/insulating compound complete with terminals, clamps,bolts,nuts and washers etc. with necessary materials and labour tools and equipments as per instructions of engineer incharge of work.

13.39 Earthing: Providing and fixing and wiring earth electrode for grounding circuits IC cutouts and other equipments on the meter board in the pit. The pits should be filled up with equal proportion of salt and charcoal 150mm around the pipe to complete depth. The connection from the pipe to the conduits etc. is to established through GI wire of sizes as per clause 7.3.3 of IS 732 using 12mm bolts, nuts, washers and check nuts, the pipe shall have 16 through holes of 12mm dia. Job 3750.00

13.4 Supply and delivery of Centrifugal pumpset at site brand new best make and with discharge duty confirming to ISI standards and its latest amendments. Discuss

13.40.1 2 HP, Size 65x50 Head 13M, Discharge 462 LPM Each 15610.00

13.40.2 2 HP, Size 50x40 Head 22M, Discharge 186 LPM Each 16993.00

13.40.3 3 HP, size 50x40 Head 30M, Discharge 198 LPM Each 18816.00

13.40.4 5 HP, size 80x65 Head 23.50M, Discharge 600 LPM Each 22310.00

13.40.5 5 HP, size 50x40 Head 46M, Discharge 174 LPM Each 26417.00

13.40.6 7.5 HP, size 100x100 Head 195M, Discharge 1200 LPM Each 30520.00

13.40.7 7.5 HP, size 80x65 Head 195M, Discharge 1200 LPM Each 33619.00

13.40.8 7.5 HP, size 65x50 Head 46M, Discharge 360 LPM Each 35150.00

13.40.9 10 HP, size 80x65 Head 34.50M, Discharge 840 LPM Each 37623.00

13.40.10 12.5 HP, size 100x100 Head 25M, Discharge 1560 LPM Each 38331.00

13.40.11 12.5 HP, size 80x65 Head 40M, Discharge 780 LPM. Each 46710.00

13.40.12 15 HP, size 80x65 Head 44M, Discharge 900 LPM Each 53967.00

13.40.13 20 HP, size 100x80 and 42M, Discharge 1320 LPM Each 65918.00

13.41 Supply and delivery at site brand new best make pressure guage suitable for centrifugal pump confirming to latest IS standards.

13.41.1 pressure guage 80MM Each 597.00

13.41.2 pressure guage 100MM Each 654.00

13.42 Supply and delivery at site brand new best make level guage suitable for centrifugal pump confirming to latest IS standards. Each 750.00

13.43 Supply and delivery at site brand new best make starter/ control panel suitable for following HP centrifugal pump confirming with ISI mark and its latest amendments.

13.43.1 Upto 7.5 HP centrifugal pump Each 9500.00

13.43.2 7.5 to 10 HP centrifugal pump Each 15550.00

13.43.3 10 to 12 HP centrifugal pump Each 35650.00

13.44 Supply, delivery, erection and commissioning at site lighting distribution board suitable for monoblock centrifugal pump confirming with ISI mark and its latest amendments. Each 3500.00

13.45 Supply, delivery, erection and commissioning at site ELCB suitable for monoblock centrifugal pump confirming with ISI mark and its latest amendments. Each 4117.00

13.46 Providing and fixing LT cable of size 4 x 25 Sqm suitable for centrifugal pump sets with ISI mark and its latest amendments. m 562.00

13.47 Supply and delivery at site brand new best make Foot valve suitable for centrifugal pump upto 10HP confirming with ISI mark and its latest amendments. Each 1750.00

13.48 Supply and delivery at site brand new best make Foot valve suitable for centrifugal pump above 12.50HP confirming with ISI mark and its latest amendments. Each 2200.00

13.49 Rewinding of monoblock motor with copper insulaton wire suitable gauge as per ISI specification with all necessary materials and labour,tools and equipments with guarantee period of not less than 12 months

13.49.1 7.5 HP monobloc motor rewinding Job 4000.00

13.49.2 10 HP monobloc motor rewinding Job 6500.00

13.49.3 12.5 HP monobloc motor rewinding Job 8000.00

13.49.4 15 HP monobloc motor rewinding Job 12000.00

13.49.5 20 HP monobloc motor rewinding Job 15000.00

13.49.6 30 HP monobloc motor rewinding Job 20000.00

13.49.7 40 HP monobloc motor rewinding Job 22000.00

13.49.8 50 HP monobloc motor rewinding Job 25000.00

13.49.9 60 HP monobloc motor rewinding Job 35000.00

13.49.10 80 HP monobloc motor rewinding Job 38000.00

13.49.11 100HP monobloc motor rewinding Job 50000.00

13.49.12 120 HP monobloc motor rewinding Job 62000.00

13.49.13 150 HP monobloc motor rewinding Job 65000.00

13.49.14 180 HP monobloc motor rewinding Job 75000.00

13.49.15 200 HP monobloc motor rewinding Job 85000.00

13.5 Providing Ball bearing as per ISI specifiction with guarantee period of not less than 12 months

13.50.1 Bearing cost for 7.5 HP Each 1880.00

13.50.2 Bearing cost for 10HP Each 2050.00

13.50.3 Bearing cost for 12.5 HP Each 2050.00

13.50.4 Bearing cost for 15 HP Each 2550.00

13.50.5 Bearing cost for 20 HP Each 3080.00

13.50.6 Bearing cost for 30HP Each 4050.00

13.50.7 Bearing cost for 40 HP Each 4600.00

13.50.8 Bearing cost for 50 HP Each 6250.00

13.50.9 Bearing cost for 60 HP Each 6500.00

13.50.10 Bearing cost for 80 HP Each 7000.00

13.50.11 Bearing cost for 100 HP Each 7500.00

13.50.12 Bearing cost for 120 HP Each 9000.00

13.50.13 Bearing cost for 150 HP Each 11000.00

13.50.14 Bearing cost for 180 HP Each 12500.00

13.50.15 Bearing cost for 200 HP Each 13500.00

13.51 Providing thrust bearing as per ISI specifiction with guarantee period of not less than 12 months

13.51.1 Bearing cost for 30 HP Each 6500.00

13.51.2 Bearing cost for 40HP Each 7500.00

13.51.3 Bearing cost for 50 HP Each 8500.00

13.51.4 Bearing cost for 60 HP Each 11000.00

13.51.5 Bearing cost for 80 HP Each 13500.00

13.51.6 Bearing cost for 100 HP Each 14000.00

13.51.7 Bearing cost for 120 HP Each 16500.00

13.51.8 Bearing cost for 150 HP Each 18000.00

13.51.9 Bearing cost for 180 HP Each 19500.00

13.51.10 Bearing cost for 200 HP Each 21000.00

13.52 Providing terminal plate as per ISI specifiction with guarantee period of not less than 12 months

13.52.1 terminal plate 7.5 to 12.5 Each 450.00

13.52.2 terminal plate 15 to 30 Each 850.00

13.52.3 terminal plate 40 to 60 Each 1050.00

13.52.4 terminal plate 80 to 120 Each 2000.00

13.52.5 terminal plate 150 to 200 Each 3500.00

13.53 Repairs to Vertical turbine pumps as per ISI specifiction with guarantee period of not less than 12 months V- T Pump

13.53.1 Phosphorous bronze bearing bush for 30 HP to 40 HP Each 4800.00

13.53.2 Phosphorous bronze bearing bush for 50 HP to 60 HP Each 5500.00

13.53.3 Phosphorous bronze bearing bush for 80 HP to 100 HP Each 7500.00

13.53.4 Phosphorous bronze bearing bush for 100 HP to 150 HP Each 8200.00

13.53.5 Phosphorous bronze bearing bush for 180 HP to 200 HP Each 9000.00

13.54 Repairs to Vertical turbine pumps as per ISI specifiction with guarantee period of not less than 12 months V-T PUMP STAGE BUSHES

13.54.1 Phosphorous bronze stage bushes for 30 to 40 HP Each 4500.00

13.54.2 Phosphorous bronze stage bushes for 50 to 60 HP Each 5200.00

13.54.3 Phosphorous bronze stage bushes for 80 to 100 HP Each 7500.00

13.54.4 Phosphorous bronze stage bushes for 100 to 150 HP Each 8500.00

13.54.5 Phosphorous bronze stage bushes for 180 to 200 HP Each 9500.00

13.55 Repairs to Vertical turbine pumps as per ISI specifiction with guarantee period of not less than 12 months V-T PUMP IMPELLER AND NECK RING

13.55.1 IMPELLER AND NECK RING for 30 HP to 40 HP Each 4800.00

13.55.2 IMPELLER AND NECK RING for 50 HP to 60 HP Each 5200.00

13.55.3 IMPELLER AND NECK RING for 80 HP to 100 HP Each 9000.00

13.55.4 IMPELLER AND NECK RING for 100 HP to 150 HP Each 8000.00

13.55.5 IMPELLER AND NECK RING for 180 HP to 200 HP Each 9500.00

13.56 Repairs to Vertical turbine pumps as per ISI specifiction with guarantee period of not less than 12 months HORIZANTAL PUMP

13.56.1 Phosphorous bronze bushes for 7.5 to 15 HP monoblock motor Each 800.00

13.56.2 Phosphorous bronze bushes for 20 HP monoblock motor Each 1800.00

13.56.3 Phosphorous bronze bushes for 40HP to 80HP monoblock motor Each 5800.00

13.56.4 Phosphorous bronze bushes for 100HP to 120HP monoblock motor Each 6500.00

13.56.5 Phosphorous bronze bushes for 150HP to 200 HP monoblock motor Each 8000.00

13.57 BEARING FOR HORIZONTAL PUMP

13.57.1 For 20 HP pump bearing Each 2500.00

13.57.2 For 30 HP Pump bearing Each 3500.00

13.57.3 For 40 to 80 HP pump bearing Each 4500.00

13.57.4 For 60 to 80 HP pump bearing Each 8400.00

13.57.5 For 100 to 150HP pump bearing Each 10200.00

13.57.6 For 180 to 200 HP pump bearing Each 10800.00

13.58 ALL TYPES OF JACK WELL V-T PUMP DETAILS as per ISI specifiction with guarantee period of not less than 12 months -For Pump dismentaling and refitting after attending repairs.

13.58.1 Up to 60 HP Each 10000.00

13.59 For Top body bush fitting

13.59.1 Up to 60 HP Each 2000.00

13.6 For Bottom body bush fitting

13.60.1 Up to 60 HP Each 1450.00

13.61 For Pumps stage body bush fitting Each

13.61.1 Up to 60 HP Each 850.00

13.62 For Pump body necking fitting Each

13.62.1 Up to 60 HP Each 1200.00

13.63 For Impeller breezing making

13.63.1 Up to 60 HP Each 1050.00

13.64 For Pump shaft press throwble

13.64.1 Up to 60 HP Each 680.00

13.65 For Pump open & fitting at work shop

13.65.1 Up to 60 HP Each 3500.00

13.66 For Connecting bush G.M new making Each

13.66.1 Up to 60 HP Each 1875.00

13.67 For Line shaft seat welding making Each

13.67.1 Up to 60 HP Each 450.00

13.68 For Oil inside new Fitting & threading Each

13.68.1 Up to 60 HP Each 1400.00

13.69 For Balancing spaider rubber guide Each

13.69.1 Up to 60 HP Each 1200.00

13.7 For New T.T nipple making

13.70.1 Up to 60 HP Each 3050.00

13.71 For Pump gear box body radial bearing

13.71.1 Up to 60 HP Each 13575.00

13.72 For Gear box ball bearing

13.72.1 Up to 60 HP Each 1500.00

13.73 For Pumping and clean pipe painting

13.73.1 Up to 60 HP Each 1675.00

13.74 For Transportation charges both side

13.74.1 Up to 60 HP Each 2500.00

13.75 Water Treatment Plants HORIZANTAL PUMP ALL TYPES-For Pump open & refitting after repairs

13.75.1 Up to 25HP Each 4900.00

13.76 For Side gland bush

13.76.1 Up to 25HP Each 1500.00

13.77 For Impeller breezing and making

13.77.1 Up to 25HP Each 1100.00

13.78 For Shaft steel welding and making bearing sheet Each

13.78.1 Up to 25HP Each 1100.00

13.79 For Shaft threading making Each

13.79.1 Up to 25HP Each 1250.00

13.8 For Joint rope of 1kg

13.80.1 Up to 25HP Each 700.00

13.81 For Pump shaft bend thrown

13.81.1 Up to 25HP Each 950.00

13.82 For Transportation

13.82.1 Up to 25HP Each 2715.00

13.83 For Pump shaft getting check nut Each

13.83.1 Up to 25HP Each 1050.00

13.84 For Both coupling new set

13.84.1 Up to 25HP Each 8500.00

13.85 Providing and installing of solar photo voltaic (SPV) water pumping system INDUCTION MOTOR, PUMPSETS AND A SUITABLE INVERTER

as per IS specification and instruction of Engineer incharge of work as per IS specification- For 3000 wp/ 3HP submersible with controller

13.85.1 Total head 30 mtrs and shut off dynamic Head 45 mtr and water out put 96000 ltrs/day. Each 267000.00

13.85.2 Total head 50 mtrs and shut off dynamic Head 75 mtr and water out put 57000 ltrs/day. Each 270000.00

13.85.3 Total head 70 mtrs and shut off dynamic Head 100 mtr and water out put 39000 ltrs/day Each 273000.00

13.86 For 4800 wp/ 5HP submersible with controller

13.86.1 Total head 50 mtrs and shut off dynamic Head 70 mtr and water out put 91200 ltrs/day. Each 383000.00

13.86.2 Total head 70 mtrs and shut off dynamic Head 100 mtr and water out put 62400 ltrs/day. Each 386000.00

13.86.3 Total head 100 mtrs and shut off dynamic Head 150 mtr and water out put 40800 ltrs/day. Each 389000.00

13.87 For 6750 wp/ 7.5 HP submersible with controller

13.87.1 Total head 50 mtrs and shut off dynamic Head 70 mtr and water out put 128250 ltrs/day. Each 565000.00

13.87.2 Total head 70 mtrs and shut off dynamic Head 100 mtr and water out put 87750 ltrs/day. Each 568000.00

13.87.3 Total head 100 mtrs and shut off dynamic Head 150 mtr and water out put 57375 ltrs/day. Each 571000.00

13.88 For 9000 wp/ 10HP submersible with controller

13.88.1 Total head 50 mtrs and shut off dynamic Head 70 mtr and water out put 171000 ltrs/day. Each 714000.00

13.88.2 Total head 70 mtrs and shut off dynamic Head 100 mtr and water out put 117000 ltrs/day. Each 717000.00

13.88.3 Total head 100 mtrs and shut off dynamic Head 150 mtr and water out put 76500 ltrs/day. Each 720000.00

P.H.Division,Motipur

Block wise (WLS,PWS, SVS) Ward Details

Sl.No Block Name of Scheme Panchayat Name of PWS Scheme PHED Wards Remarks

PWS Wards No. Total WIMC Wards No No. of Scheme

1 Meenapur Turki Khararoo East Turki Khararoo East 6,10,11,13 4 6,10,11,13 4

2 Turki Khararoo West Turki Khararoo West 11,13 2 11,13 2

4 Harka Manshahi Harka Manshahi 4,5,11,12,13 5 4,5,11,12,13 5

5 Paroo Anandpur Kharauni Anandpur Kharauni 4,6,7,8,13 5 4,6,7,8,13 5

6 Dharfari Dharfari 10,13,14,15 4 10,13,14,15 4

7 Moujamma Moujamma 12,13,14,15 4 12,13,14,15 4

8 Moujamma Moujamma 1,2,3,9,10,11 6 1,2,3,9,10,11 6

9 Pandeh Pandeh 1,2,3,4,5 5 1,2,3,4,5 5

11 Paroo South Paroo South 5,6,7,8,11,12 6 5,6,7,8,11,12 6

12 Devariya East Devariya East 1,2,11,12,13,15 6 1,2,11,12,13,15 6

13 Kanti Mustaffapur Mustaffapur 1 1 1 1

14 Har chanda Har chanda 2,11,13 3 2,11,13 3

15 Ramnath Dhamauli East Ramnath Dhamauli East 7,9,11,15 4 7,9,11,15 4

16 Panapur Haweli Panapur Haweli 8,11,13,14,15,16 6 8,11,13,14,15,16 6

17 Sherukahi Sherukahi 1,3,5 3 3,5 2

18 Har chanda Har chanda 3 1 3 1

19 Ramnath Dhamauli East Ramnath Dhamauli East 6,8 2 6,8 2

20 Ramnath Dhamauli West Ramnath Dhamauli West 1,3,8,15 4 8 1

21 Sherukahi Sherukahi 10 1

22 Ramnath Dhamauli West Ramnath Dhamauli West 6 1

23 Mustaffapur Mustaffapur 9 1 9 1

24 Marwan Jiyan Khurd Jiyan Khurd 1,3,6,7 4 1,3,6,7 4

25 Jiyan Khurd Jiyan Khurd 4,5,6,15 4 4,5,6,15 4

26 Karjadih Karjadih 10,12 2 10,12 2

27 Bakrkagaon Utri Bakrkagaon Utri 3,9 2 3,9 2

28 Mohammadpur Subey Mohammadpur Subey 3,4,5,11,12,13,14 7 3,4,5,11,12,13,14 7

29 Bakrkagaon Utri Bakrkagaon Utri 5,12,13 3 5,12,13 3

31 Sahebganj Madhopur Hazari Madhopur Hazari 3,4,5 3 5,6,7,12 4

32 Rampur Asli Rampur Asli 14 1

33 Saraiya Basantpur South Basantpur South 7,10 2 7,10 2

34 Saraiya Saraiya 3,8,9 3 8,9 2

35 Kudhani Chajjan Harishankar Chajjan Harishankar 5,7,8,9,10 5 5,7,8,9,10 5

Total No. of Scheme (WLS) 125

1 Meenapur Meenapur Meenapur 7,8 1

2 Kudhani Turki Turki 9,10,13,14,15 1

3 Kanti Navrullahpur Bangra Navrullahpur Bangra 1,2,3,4,10 1

4 Saraiya Saraiya Saraiya 4,5,7,11,12,13 1

5 Paroo Moujjama Moujjama 4,5,6,7,8 1

6 Marwan Bakrkagaon Utri Bakrkagaon Utri 1,6,7,8 1

7 Meenapur Panapur Panapur 3,4 1

8 Saraiya Basantpur South Basantpur South 1,2,3,5,6,8,9 1

9 Meenapur Turki Khararoo West Turki Khararoo West 1,3,5 1

10 Sahebganj Madhopur Hazari Madhopur Hazari 8,9,10,11 1

11 Motipur Motipur Kathaiya Motipur Kathaiya 6,7,8,9,10 1

12 Kudhani Chajjan Harishankar Chajjan Harishankar 1,2,3,4,6 1

13 Paroo Phulwariya Phulwariya 7,8,9,10 1

14 Paroo Dharphari Dharphari 2,3,6,8,9,11 1

Total No. of Scheme (PWS) 14

1 Saraiya Chako Chapra Ramkrishan Dubiyahi 6,13 1

2 Saraiya Jagir Tola Ramkrishan Dubiyahi 14 1

3 Kanti Saieen Saieen 1,2,3,4,13,14,15 1

4 Kanti Saieen Brijlal Saieen 5,6,7 1

5 Kanti Madhukar Chhapra Saieen 8,9,10 1

6 Kanti Rannu Rai Saieen 11,12 1

7 Meenapur Chatursi Chatursi 7,8,9 1

8 Meenapur Bhagwan Chhapra Chatursi 5,6,12 1

9 Meenapur Khoja Pakari Chatursi 13,14 1

10 Meenapur Neknama Chatursi 10,11 1

11 Meenapur Basudev Banua Chatursi 1 1

12 Paroo Matihani Gyaspur 9,14,15 1

13 Saraiya Shekh Dhanauj Ramkrishan Dubiyahi 7,8,9 1

14 Saraiya Jalalpur Ramkrishan Dubiyahi 10,11,12 1

15 Paroo Gyaspur Gyaspur 1,2,3,4,5,6,7,8 1

Total No. of Scheme (SVS) 15

Executive Engineer

P.H.Division, Motipur