Augmentation of WSS Pandli Chunani Kuklah in GP Kashoud and Kuklah from Khudagi Khad in Tehsil Balichowki Distt. Mandi (H.P)

Amount

Excavation in foundation and trenches etc. in earth work in all kinds of soil such as pick work, jumper work, blasting soft orhard rock by chiselling soft/hard rock where blasting is prohibited in all leads and lifts including trimming/dressing of sides and beds stacking the excavated soil clear from the edge of excavation and then returning the excavated soil aftrer completion of work in 15cm layers when required into plinths, sides of foundation etc. consolidating each deposited layers by ramming and watering and then disposing of all surplus excavatred soil complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Providing and laying cement concrete 1:6:12 (1 cement : 6 Sand :12 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form workin: Foundation and plinth in all leads and lifts.

Providing and laying cement concrete 1:5:10 (1 cement : 5 Sand :10 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form workin: Foundation and plinth in all leads and lifts.

Providing and laying cement concrete 1:3:6 ( 1cement:3sand: 6 graded stone aggregate 20 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts.

Providing and laying cement concrete 1:11/2 :3 ( 1cement: 1 1/2 sand: 3graded stone aggregate 20 mm nominal size )and curing complete excluding the cost of form work and reinforcement with in all leads and lifts and entire satisfaction of Engineer incharge in:-

Foundation, footings bases of columns and the like and mass concrete.

Walls any thickness but not less than 0.1 mtr. thickness attached pillasters, buttresses plinth and string courses etc. from top of foundation level upto floor two level

Suspended floors, roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilivers up to floor two level.

Suspended floors, roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilivers up to floor two level. ( Dome Slab)

Lintels, beams, girders, bressumers and cantilevers up to floor two level.

Providing form work with steel plates 3.15mm thick welded with angle iron 30x30x5mm so as to give a fair finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4mtrs. and removal of the same for in-situ reinforced concrete and plain concrete work in all leads and lifts.

Vertical surface such as walls(any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like (Plain wall)

Flat surface such as soffits of suspended floors, roofs, landing and the like floor etc. upto 200mm in thickness as per direction and to the entire satisfaction of the Engineer-in-charge.

Beams,cantilivers,girders and lintels sides and soffits of beams,beam haunchings, cantilivers , girders, bressumers and lintels not exceeding 1 metre in depth.

Sloping battering surfaces including folded plates: where inclination to horizontal does not exceed 30 Degree requiring shuttering only to the under side with in all leads and lifts.

Edges of slabs and breaks in floor and wall under 20 cm wide in all leads and lifts.

Providing form work of ordinary timber plankings so as to give a rough finish including centering ,shuttering, propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 meters and removal of the same for-in-situ reinforced concrete and plaiin concrete work in:-

Arches, domes, up to all span in all leads and lifts.

Providing and laying tor steel reinforcement for RCC work including bending, binding and placing in position complete including cost of binding wire upto floor two level in all leads and lifts.

Providing and laying cement concrete 1:2:4(1Cement :2 sand:4 graded crushed stone aggregate 20mm nominal size and curing completre excluding the cost of form work and reinforcement for reinforced concrete work in all leads and lifts in :-

Suspended floors, roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilivers up to floor two level.

Fixing of GI pipe for inlet, outlet, over flow and scour pipes in all leads and lifts complete in all respect including cutting and welding of pipe: -

50mm dia

65 mm dia

Providing and fixing Gum Metal wheel valve with Wheel in all leads and lifts : -

50mm dia nominal bore.

65mm dia nominal bore.

1.80 metre high fencing with 2.50 metre angle iron post 50x50x6mm 2.50 metre centre to centre with nine horizontal lines and two diagonals of galvanised steel bar bed wire (IS:278-1962 type-I) weighing 9.38 kg/per 100 metre (minimum) strained and fixed to posts with G.I. staples, including coal tarring of ballies complete in all leads and lifts.

Steel work welded in built up sections, trusses and framed work including cutting,hoisting, fixing in position and applying a priming coat of red lead paint :- in gratting, framed guard bar, ladders, railing brackets and similar works in all leads and lifts.

Providing and fixing 3.15mm thick MS sheet man hole cover fixed with 50x50x6mm angle iron frame 500x500mm with welding including hold fast 25x6mm 150mm long, handles 150mm long 8mm dia bar and locking arrangement complete in all leads and lifts.

Providing and fixing cast iron spun spigot and socket soil ventilating pipe lead cauled joints to be measured and paid for separately 100mm dia

Providing and fixing CI Cowl 100mmdia complete in all respect

Providing and placing in horizontal layers filtering media duly graded screened washed and cleaned as specified by the Engineer-in-charge including all leads and lifts.

Top layer:- Fine sand screened, cleaned, washed and graded effective size 0.20 to 0.40 with uniformity co-efficient 2 to 3).

2nd layer:- Coursed sand screened, washed and graded from 3mm to 6mm

3rd layer :- Bajari screened, washed and graded from 6mm to 20mm

4th layer :- Bajari screened, washed and graded from 20mm to 25mm

Bottom layer :- Broken stone screened washed and graded from 50mm to 75mm

Providing and placing 1st class standard bricks in filter bed in to leayer so as to make cross drains as per direction of the Engineer in Charge.

Randum rubble masonary polygonal rubble masonary (uncoursed brought to courses with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1cement: 6 sand: 12 graded stone aggregate 20mm nominal size) in cement mortar 1:6 (1cement: 6 sand) including all leads and lifts.

Boulder filling behind retaining wall under floor with in all leads and lifts complete in all respect.

Brick work using common burnt clay building bricks masonary in super structure above plinth in cement mortor 1:4(1cement :4sand) complete in all respect in all leads and lifts (i) 2nd class bricks

Provding wood work in frames of doors,windows,and other frames wrought,framed and fixed in position in all leads and lifts :- 1st class Deodar wood

Providing 40x3mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm 1:3:6 ( 1cement: 3 sand :6 graded stone aggregate 20mm nominal size complete in all respect in all leads and lifts.

Providing and fixing panneled glazed or panelled and glazed shutters for doors, windows and clerestory windows,including black enamelled iron butt hinges with necessary screws. 45 mm thick. 2nd class deodar wood.

Providing and fixing MS grills of required pattern in wooden frames of windows etc. with MS flats, square or round bar with round headed bolts and nuts or by screws (Plain grills)

Cement concrete flooring 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement with in all leads and lifts : - 40 mm thick.

6mm cement plaster to ceiling in cement mortar 1:3 (1cement :3sand) inall leads and lifts.

20mm cement plaster in single coat on rough side of brick/ concrete/ stone walls for interior plastering upto floor two levels including arrises internal rounded angles chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6 (1cement:6sand) in all leads and lifts.

15mm cement plaster in single coat on rough side of brick /concrete stone walls for interior plaster up to floor two elvel including arrises, internal rounded angles, chamfers ad/or rounded angles not exceediong 80mm in girth and finished even and smooth in C.M 1:4 (1Cement :4 Sand)

White washing with lime on undecorated wall surfaces two coats give an even shade including thoroughly brooming the surface to remove all dirt dust and other foregin matter in walls in all leads and lifts.

Distempering with dry distemper of approved brand and manufacture (two coats) and of required shade on undecorated wall surfaces to give an even shade sand papered smooth complete in all respect in all leads and lifts.

Applying priming coat on new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,greese,dirt and other foreign matters,sand papering and knotting.Ready mixed paint brushing wood primer pink.

Painting two coats (excluding priming coat) on new wood and wood based surfaces,with enamel paint to give an even shade including cleaningthe surface of dirt ,dust and other foreign matters sand papering and stopping with enamel paint other than white

Providing and fixing anodised MS sliding door bolts with bolts and nuts screws etc. complete.: - 250*16 mm

Providing and fixing anodised MS tower bolts ( barrel type) with screws etc. complete.

Providing ad fixing anodised MS handles with necessary screws etc. complete.: - 125 mm

Providing ad fixing anodised MS hooks and eyes with necessary screws etc. complete.: -250 mm

Providing plinth protection 50 mm thick in cement concrete 1:3:6 ( 1 cement, 3 sand,6 graded stone aggregate 20 mm nominal size ) with in all leads and lifts complete in all respect.

Proving under layer for plinth protection of 75 mm thick(unconsolidated) bed dry brick/stoneAggregated 40 mm nominal size will rammed with rammed and consolidated and grouted with fine sand including preparation of ground.

Half bricks masonary in common burnt clay building bricks in 1:4 (1cement :4 sand) in super structure above plinth level upto all floor level in all leads and lifts. (2nd class )

Providing and fixing vitreous china wash down water closet (Indian Type, W.C pan) with integral P or S trap including jointing the trap with soil pipe in cement mortar 1 : 1 ( 1 cement 1 sand) ( Seat and cover to be measured and paid for separately) (White colour)

Providing and fixing 32 mm CP brass waste pipe for wash basin in all leads and lifts.

Providing and fixing 10/12.5/15 litres vitreous china low level flushing cistern with a pair of CI or mild steel brackets complete with fittings such as lead valve less syphon 15mm nominal size brass ball valve with polythene float CP brass handle unions and couplings for connection with inlet , out let and over flow pipes 40mm dia CP flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow) pipe to be measured and paid for separately.

Providing & fixing viterious china wash basin with single hole for pillar tap with CI or MS bracket painted white including cutting hole including good the same excluding fitting Cera sanitary work (cornet) white 550x400 white

Providing and fixing floor trap for wash basin and sink in all leads and lifts.

Providing and fixing 600mmx450mm beveled edge mirror of superior glass mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washers in all leads and lifts.

Providing and fixing PVC pipe ISI marked 100mm dia in all leads and lifts.

Providing and fixing GI union 15mm dia ISI marked in all leads and lifts.

Providing and fixing GI Elbow 15mm dia ISI marked in all leads and lifts.

Providing and fixing G.I. Tee15mm equal ISI marked in all leads and lifts.

Providing and fixing G.I. Socket 15mm dia ISI marked in all leads and lifts.

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fittings and clamp including making good the wall ceiling and floor in all leads and lifts.) 15 mm nominal bore

Providing and fixing G.I. Nipple 15mm dia ISI marked in all leads and lifts.

Providing and Fixing of water storage tank sintex having of capacity 500 liters with necessary fittings including over flow pipes, scour pipes etc. inlet and outlet and inside paint of required size for inlet or outlet and inside paint of approved quality complete including hoisting complete in all respects.

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required (Group A)

Wiring for power plug with 2x4sq.mm PVC insulated 9head resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit alongwith 1 to 4 Sq.mm HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 1 No.HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required. : - 2x1.50 Sq. mm.

Supplying and fixing of following way single pole and neutral steel sheet MCB distribution board 240 volts on surface/ recess complete with tinned copper busher wire set neutral link earth bar din bar detachable gland plate blanking plate cable identification levels interconnection phosphaized and power painted including earting etc., as required.

Supplying and erection of 6 Amps. to 32 Amps. Rating 10 KA breaking capacity, 240 volts, C curves, miniature circuit beaker of following poles in the existing MCB DB complete with connections etc. as required Single pole Cat. A

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. (63 amp. CAT - A)

Supplying and fixing following rating, double pole (single phase & neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps Cat A

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required:- Ceiling Fan 1200 mm sweep, Category-A

Supplying and fixing plain pendent with 16/0.20 mm twin twisted, flexible, PVC insulated, cotton braided, copper cable and brass pendent holder including connections etc. as required:-

Providing and fixing shock proof slim decorative extruded fixture with domestic electronic ballast, suitable for 36 watt FTL (T8), complete with all accessories (excluding the T-8 Tube), connections, testing and commissioning etc. as required :- 1 x36 watt-FTL(T8) (Category-A)

Providing and fixing following type of CFL rod lighting Luminaires Epoxy black powder coated sheet steel housing with epoxy white powder coated XRCA sheet steel geartray clear a crylic cover aluminium reflector (but excluding the cost of CFL) complete with all accessories connection, testing & commissioning etc. as required : - 1x85 watt CFL fixture.

Providing and fixing 85 watt CFL in existing fixture in all leads and lifts.

sanjeev govt cont

gagan ohri