ADDITION/ALTERATION OF TWO ROOMS BEHIND THIN FILM DIVISION (BUILDING NO P-7) AT IRDE UNDER GE (I) RND DEHRADUN

Amount

Demolition of cement concrete (unreinforced) of any description as in ground floors and pavings not exceeding 15cm thickness (above or below ground floors) with and including removing Debris out sideMOD Land at contractor is own arrangement complete all as specified and directed.

M&L for cement concrete type B-1 (1:2:4) 20 mm graded aggregate in foundation, filling, PCC padding in sunken floors/ roofs (for slope correction) and mass concrete complete all as specified and directed.

M&L for 75 mm thick PCC 1;3:6 type C-2 using 40mm graded stone aggregate as in plinth protection or similar places and finishing the surface even & smooth with out using extra cement including making joints 12mm wide to the full depth of PCC at every 3 meter and every change of direction and filling the same with mixture of bitumen & sand in ratio (1:1) by weight including necessary form work complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 18 to 20 mm thick in flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over with and including screed bed or bedding layer of cement mortar 15mm thick in CM 1:6 complete all as specified and directed.

M&L for Kota stone slab 15 to18 mm thick in riser of steps, skirting, dado and pillar laid over and including 10 mm thich rendering cement morter (1:3) and jointed with grey cement complete all as specified and directed.

M & L for taking down old cement plaster/Grit wash on stone wall or brick surfaces of walls including raking out joints, hacking for key and scrubbing down with water with and including, removing debris out sideMOD Land at contractor is own arrangement ) complete all as specified and directed.

M&L for brick work with sub class 'B' bricks (old size) straight or curved on plan exc 6.00m mean radius built in CM (1:4) complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of concrete /brick surface in cement mortar 1:6 finished fair and even as in wall etc complete all as specified and directed.

M&L for prepration of new plaster surfaces of wall and applying two coat of oil bound distemper over and including a coat of alkali primer & 3 mm thick wall care puttty complete all as specified and directed.

M&L Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified .

M & L for preparation of newly plastered surface of wall and applying two coat of cement base paint complete all as specified and directed

M&L for Complete removal of existing treatment of old surface and washing rubbing down and stoping of distempered and painted surface of wall and applying two coats of cement based paint complete all as specified and directed.

M&L for preparing old surfaces of walls plastered by brooming down with steel or wire brush and scraping down smoke soot, moulds moss & efflorescent salt and trading oil and greasy spots , washing rubbing down and stopping of distempered and painted surface & removing all vegetation growth, nails and making good holes,cracks etc complete by necessary putty and make the surface smooth by rubbing with sand papers etc and applying one coat of distemper oil emulsion on old prepared surfaces of Ceiling complete all as specified and directed.

M&L 20 mm thick cement plaster on fair face of concrete surface including repair of doubing roof/chajja/facia surfaces in CM 1:3 finished even land smooth without using extra cement over and applying two coat of cement base paint over a coat of primer after prepration of newly plastered surfaces up to Six story buildings of walls including scaffolding and all necessary items complete all as specified and directed.(Water proofing compound shall be measured and paid separately )

Supply only Liquid water proofing compound complete all as specified and directed.

Taking down chowkats or frame of any description exc 1.5 Sqm each and n.exc 4Sqm with shutter(without taking off shutters from the frames) & remove off the premises complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 sqm each& remove off the premises complete all as specified and directed.

Supply and fixing factory made uPVC white colour Two track two panels sliding glazed window upto 1.50m height made of (small series) frame 52 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) comprising of uPVC multi-chambered frame, with uilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder oated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and ecessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on is account shall be made

Supply and fixing factory made uPVC white colour Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension (Area of window upto 0.75 sqm.) comprising of uPVC multi chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made complete all as specified and directed.

M&L for 4.8 mm thick sheet glass ordinary quality in panes not exc 0.50 sqm each fixed with & including rubber gasket in aluminium frame work complete all as specified and directed.

S&F mild steel for framed work such as grills, gratings, etc With ends of bars shouldered and riveted, or forged into spikes, framed guard bars, barred iron doors ladders, framed balusters, walk ways, railings, framework of water tanks and similar work con-forming to Fe. 290. Gde-E-165 complete all as specified & directed.

M&L for Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer.

M&L for 40 mm thick flush shutters, solid core construction, exterior grade with block board core and plywood face, pannels, commercial type on both sides and one face is covered withdecorative face veneer with lipping / frame to match, including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

S&F first class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, all as specified and directed by Engr-in-Charge.

M&L Preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer

S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed.

S&F aluminium handles, cast type, anodised 150 mm size complete all as specified and directed.

S&F floor door stopper double leg of aluminium alloy body of 140 mm length with aluminium base plate of size 50 mm x 40 mm complete all as specified & directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed all as specified and directed.

M&L for glossy finish rubber moulded chequered cement concrete tile 30 cm x 30 cm x 25 mm thick set jointed and pointed in neat cement slurry in floor with grey cement and pigment to match over and including 15mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finished complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise described and removal of dismantling materials with and including removing Debris out sideMOD Land at contractor is own arrangement complete all as specified and directed.

S & F in repair 1.25mm thickness of laths steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, haps and staple and one shop coat of primer erected in position as indicated push pull or manual type complete all as specified and directed

Taking down of carefully unserviceable Aluminium/copper point wiring (light, fan socket or power) complete with fitting such as switches, ceiling rose lamp holder, sockets, fan regulators, SK/FTL light fittings etc removing materials for store for keeping in safe custody or for taking credit (credit for above items should be taken as per conditions separately) and making good disturbed surfaces of walls, floors etc as specified and directed.

M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade FRLS-IS 694 cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, concealed conduit wiring in walls and surface with GI saddles GI screws, rawal plugs in ceiling or roof if not possible including Tee, Junction boxes and provision of flush metal boxes, inner and outer plate suitable for modular switch, socket and fan regulator as per site requirement and drawing continuous earth wire with and including PVC insulated unsheathed 1100 Volts grade FRLS-IS 694 cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for one light/Fan point controlled by one Switch.

All as per Srl item No 35 above for point wiring for 5 pin switch socket outlet, 5/6 Amps on same board complete all as specified and directed.

All as per Srl item No 35 above for point wiring for 5 pin switch socket outlet, 5/6 Amps on independent board complete all as specified and directed.

All as per item No 35 above for one power point 3 pin 15 Amps socket out let PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 2.5 Sq mm (Nominal area) including earth wire PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 2.5 Sq mm (Nominal area)cable common connected to earth dolly, all as specified for one 3 pin 15 amps socket outlet point controlled by one switch complete all as specified and directed.

S&F Modular switch piano single pole one way 6 amp complete all as specified and directed.

S&F Modular switch piano single pole one way 16 amp complete all as specified and directed.

S&F Modular socket outlet 2/3 pin combined 2 module 6/16 amp complete all as specified and directed.

S&F Modular socket outlet 2/3 pin combined 2 module 6 amp complete all as specified and directed.

Supply & fixing of ceiling rose, surface bakelite, 65x50mm, three terminals 240 volt complete all as specified and directed.

Supply & fixing in replacement of LED building light 1X35 Watt,pressure die cast aluminium housing,heat resistance toughened glass with frame and IP 66 protection for better optics for uniform distribution and connection with three core copper flexiable cable 16/0.20 mm from ceiling rose to fitting complete all as specified and directed

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete alll as specified and directed

Supply & fixing in replacement of 12 way SPN DB double door type Suitable for surface and flush mounting. IP 43 with metal doorcomplete all as specified and as directed.

Supply & fixing in replacement of MCBs, SP 6 to 32 Amps C characteristics of 10 kA breaking capacity, including all incoming and out going electric connection. complete all as specified and as directed.

Supply & fixing in replacement of MCBs, SPN 40 Amps C characteristics of 10 kA breaking capacity, including all incoming and out going electric connection. complete all as specified and as directed.

M&L sub main wiring using two single core PVC insulated, unsheathed stranded copper conductor cable of size 6 Sqmm of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) of suitable dia not less than 25 mm dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 6 Sqmm as earth continuity conductor wall/ ceiling/concealed surface etc complete all as specified and directed.

KISHORE ENTERPRISES (BID ID -3503729)

M/s Gupta Associates (BID ID -3503321)

M/S P K ARORA (BID ID -3509152)

JS CONSTRUCTION COMPANY (BID ID -3505596)

M/S Anil kumar (BID ID -3503650)