SPL REP TO BLDG NO. P-356F AND P-371 OF HQ MECH BDE IN THE AREA OF AGE B/R-I AND PROVN OF 16 X SPLIT AIR CONDITIONER FOR BLDG NO. P-1873 (REGREM / CENTREM COMPLEX) UNDER GE ARMY NO.1 JODHPUR

Amount

Demolition of unreinforced cement concrete in ground floors and pavings not exceeding 15cm thickness ( below or above ground level) of any description and removing rubbish to out side MD land complete all as specified and as directed.

M&L plain cement concrete (1:4:8) type D-2 using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified & directed

M&L 50 mm thick PCC (1:3:6) type C-1 using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight complete all as specified & directed

Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick with 6 mm thick top layers of anti abrasive material of M-35 grade with any colour, design & pattern, & size/ shape, as approved by GE as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Supply and laying machine / factory made kerb stone of M-25 grade,at or near ground level, cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, complete all as specified and directed.

M&L for Moorum / red bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering, complete all as specified and directed.

Demolition of stone / boulder masonry walling, built in cement mortar including all quoins, arches, pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and directed.

M&L for cutting into old masonry to form toothings for bonding in new brick or stone work including making good in cement mortar 1:6 complete all as specified and directed.

M&L for squared rubble walling, Jodhpur type, regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed.

All as per item No. 9.00 here-in-above, but except stone

M&L precast cement concrete block masonry using PCC 1:2:4, type B-1 solid blocks, 10 cm in width and setting in cement mortar 1:4, straight or curved on plan exceeding 6 m mean radius complete all as specified and directed.

Extra over stone walling for hammer dressing to face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface n exc 20mm and dressing face beds and joints, complete all as specified and directed.

Dismantling, stone slab, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as directed.

M&L for 100mm thick Cement concrete type D2, 1:4:8 (40mm graded aggregate) as in sub base, complete all as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4, type B-0 (using 12.50 mm graded crushed stone aggregate), as in base course, to receive floor finishes, complete all as specified & directed.

M&L for non skid ceramic coloured tiles (premium quality) of size 6 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including M&L 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

All as per item No. 16.00 here-in-above, but as in skirting with 10 mm thick backing coat in cement motar CM 1:4.

All as per item No. 16.00 here-in-above, but size of tile exceeding 0.11 Sqm but n.exc. 0.18 sqm .

M&L for glazed colour ceramic tiles (premium quality) of size 250X450X6-7mm / 300X450X6-7 mm, as in vertical surface such as i.e. dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over & including M&L 15mm thick backing coat in CM (1:6) complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid dry or laid dry and pointed complete all as specified and directed.

M&L 18 to 20 mm thick machine cut Kota stone in shelves and other places etc laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing complete all as specified and directed.

M&L for 20 to 22 mm thick (telephone black shade) granite stone, as in WHB counter top, machine cut, (table rubbed and polished) best quality as per sample, including & over 20 mm thick screeding in CM1:3 including rounding & double mouldlng with jointless finish of the edges, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.providing suitable dia hole in the slab for the gas pipe, complete all as specified and as directed.

Taking down cement plaster any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified and as directed.

M&L rendering 15mm thick in CM 1:4 externally, on stone masonry wall surfaces, finished even and fair without using extra cement complete all as specified and directed.

M&L rendering 10mm thick in cement mortar 1:3 on concrete ceiling /chajja/facia, finished even and smooth without using extra cement, complete all as specified and directed.

M&L rendering 5mm thick in cement mortar 1:3 on concrete ceiling /chajja/facia, finished even and smooth without using extra cement, complete all as specified and directed.

M&L rendering 15mm thick in cement mortar 1:6 internal on stone masonry surfaces , finished even and smooth without using extra cement complete all as specified and as directed.

Racking out joints/ pointing to squared rubble or polygonal rubble un-coursed or brought up to courses masonry built in cement mortar or cement lime mortar, coursed or un-coursed in walls not less than 12mm deep, washing the joints, removing rubbish off the premises and keeping the surface to pointed or plastered wet for two days prior to re-pointing or plastering complete all as specified & directed.

M&L keyed pointing in cement mortar (1:3) to squared rubble masonry regular coursed or un coursed complete all as specified & directed.

M&L Preparing new plastered or unplastered surfaces and applying with wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over one coat of primer on walls complete all as specified and as directed.

M&L for complete removal of existing treatment of any description on walls and applying with wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over & including M&L single coat of primer on walls complete all as specified and as directed.

M&L for Preparation of new plastered or unplastered surfaces of wall and applying three coats of white wash on wall surfaces complete all as specified and as directed.

M&L for Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash on ceiling surfaces complete all as specified and as directed.

M&L for preparation of old decorated wall surfaces plastered or unplastered, by brooming down or steel wire brushing, scrapping down moulds, moss and efflorescent salts and trading oil & greasy spots, including cornices etc and applying one coat of white wash on wall, complete all as specified and directed.

All as per item No. 34.00 here-in-above, but as on ceiling surfaces

Preparation of new plastered or un-plastered surfaces of walls and applying two coats of cement base paint over & including M&L single coat of white wash complete all as specified and as directed.

M&L for preparation of old decorated wall surfaces plastered or unplastered and applying one coat of cement base paint on wall, coloured and shade as approved by GE, complete all as specified and directed.

M & L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over & including M&L single coat of pink primer complete all as specified and as directed.

M&L preparation of steel surfaces of any description over 10cm width or girth not otherwise described and apply two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified & directed

Taking down chowkhats or frame with shutters (without taking of shutters from the frames) area not exc 1.5 Sqm each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking of shutters from the frames) area exc 1.5 Sqm but not exceeding 4 Sqm each, complete all as directed.

S&F rolled mild steel sections like angle, channel, flat, square etc as in framed work such as grills, gratings, etc, with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars barred iron doors; chowkhat, doors with MS sheet, ladders ;framed balusters walk ways railings framed work of water tanks and similar work confirming toFe-290Gde E-165 complete all as specified & directed

M&L for mild steel framed brackets as in cooler stand / chajja framing, made of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel'), complete all as specified & directed .

S&F steel work in tubular trusses including special shaped washers etc complete using ERW or induction butt welded tubes confirming to IS:1161-1979 Grade St-240, including M&L preparation of surface and applying one shop coat of zinc chromate primer paint, at Contractor’s workshop before fabrication, complete all as specified and as directed.

S&F Prepainted Galvalume aluminium zinc coating GI based corrugated steel Sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws including dismantling of old broken plain or corrugated AC sheets as in roof coverings complete all as specified and as directed.

M&L as in repairs for fabrication of pressed steel cupboard shutters using 1.00 mm thick MS plain sheet & with frame 1.25 MM thick bent to shape, including two coats of syn enamel paint on int surfaces & two coats of hammer tone finish on external surfaces alongwith locking arrangement mortice lock handle etc., complete all specified and directed.

M&L 35mm thick factory made 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I Section 8 Clause 8.24 (a), including M&L Aluminium grill medium size 50 X 50 mm and wirecloth 0.36 mm niminal dia and 1.40 mm apeature, complete all as specified and as directed.

M&L factory Made flush shutters, 35 mm thick solid core with block board core constructionand plywoodmface panels, commercial type on both sides salmaica, as per IS 2202(part-I, 1999) . The stiles & rails shall be with out any joint and made with non- coniferous timber hard wood (Hillock/ Mirantee/ Bosum/ Benteak) with moisture content not less than 12% as per IS. The face panel comprising of ply wood or cross band and face veneers shall be glued by hot pressed process. The over all finished thickness of face panel shall not be less than 40mm while the thickness face veneer shall not be less than 0.6 mm complete all as specified and directed.

M&L factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC ‘C’ channel having a wood grain printed PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and Wood Grain Printed(Both sides) PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wood grain printed (both sides) PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per spec & drawing

M& L for solid PVC door frame of size 50x47mm made out of 5mm wood grain printed colour PVC sheet reinforced with MS square tube complete all as specified.

Taking down steel windows and ventilators ( glazed / fly proof) of any description complete all as specified and as directed.

M&L factory made box type steel window side hung shutter, with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer (with or without cooler opening), complete all as specified and directed. Note:- Glass panes, guard bar & wire cloth shall be measured and paid seperately.

All as per item No. 52.00 here-in-above, but without glazing bar

M&L factory made box type steel ventilator top hung shutter, with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified

All as per item No. 54.00 here-in-above, but without glazing bar

S&F of aluminium anodized,tower bolt 200 mm long complete all as specified and directed.

S&F 150 mm size aluminium anodised handles, caste type, complete all as specified and as directed.

S&F 300 mm length aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed .

S&F 100mm size butt hinges stainless steel, with stainless steel hinge pin, anodised type B-21 complete all as specified and as directed.

S&F 100mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and as directed.

S&F 100mm size single action door spring hinge complete all as specified and directed.

S&F floor door stopper of alluminium alloy body and tounge anodised with hard drawn steel spring 140mm long complete all as specified and directed.

S&F of 4 mm thick pinheaded figured glass panes of size not. exceeding 0.5 Sqm fixed with oil putty complete all as specified and directed.

S&F for 3 mm thick plain sheet glass ordinary quality & glazing complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18 mm complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18 mm with necessary fitting on steel/ wooden surface complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 by using 20 mm graded stone aggregate as in bed block for fixing of hold fast complete all as specified and as directed.

M&L for mild steel work as in hold fasts, clamps, bands, straps or stays, wall ties, hooks etc confirming to Fe - 290, Grade E-165 including prepartion of surfaces and treated with coal tar and sanded with clean sharp sand complete all as specified and as directed.

S& F in repairs stainless steel curtain rods of 25mm dia, including 8 nos PVC rings per running meter of curtain rod complete all as specified and directed.

S&F in repair shelf of PTMT fixed with and including chromium plated brass screws and wooden cleats (Min weight 300 gms)

S&F in repair soap dish of PTMT fixed with screws complete all as specified and directed.

S&F in repair PTMT towel rail 450mm long fixed to wall with chromium plated brass screws and wooden cleats (Min weight 170gms) approved make complete all as spcified and directed.

S&F in repair MS chromium plated peg set of five fixing with wall complete all as specified and directed.

S & F in repairs stainless steel kitchen sink with drainage board, made of stainless steel 1 mm thick, with plugs, washers and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.

S&F in repairs vitreous china squatting pan "Orissa" pattern, size 580 x 440mm white, with integral foot rest (Excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe,lime/cement concretebedding and making good to the floor, including provision of cement concrete bedding 1:5:10 type E2 complete all as specified and as directed. complete all as specified and as directed.

S&F in repairs vitreous china wash basin white, flat back of size 580 X 450mm white including 32mm size waste fittings, brass, chromium plated, coupling, waste pipe of 32mm dia, MS brackets including cutting for and pinning in ends of brackets errect stand, fixing waste pipe, complete all as specified and as directed.

Dismantling of cast iron /PVC/AC pipes of 100mm / 110mm internal dia including fittings, jointed in cement mortar complete all as specified and as directed.

Dismantling of cast iron /PVC/AC pipes of 75mm internal dia including fittings, jointed in cement mortar complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps of suitable size complete all as specified and as directed .

All as per item No. 80.00 here-in-above, but 75 mm bore pipe

All as per item No. 80.00 here-in-above, but pipe laid in trenches or floors

All as per item No. 82.00 here-in-above, but 75 mm bore pipe

S&F 110 mm bore (SWR) PVC bends any radius with access door complete all as specified and as directed.

All as per item No. 84.00 here-in-above, but 75 mm bore pipe

S& F 110 mm bore PVC [SWR] branch piece, single (single T) equal or unequal complete all as specified and as directed.

All as per item No. 86.00 here-in-above, but 75 mm bore pipe

S&F 110mm PVC (SWR) vent cowl all as specified and directed.

S&F 75mm PVC (SWR) vent cowl all as specified and directed.

S&F 110mm PVC (SWR) reducers all as specified and directed.

S&F 75mm PVC (SWR) reducers all as specified and directed.

S&F 110mm PVC (SWR) couplers all as specified and directed.

S&F 75mm PVC (SWR) couplers all as specified and directed.

S & F in repairs 100mm bore cast iron FLOOR trap with grating including jointing to waste pipe, fixed in cement concrete type B1, 1:2:4 complete all as specified and as directed.

S & F in repairs100mm bore cast iron nahani trap with grating including jointing to waste pipe, fixed in cement concrete type B1, 1:2:4 complete all as specified and as directed.

S & F brass chromium plated shower rose of size 50mm with or without swivel joints fixing to steel pipes complete all as specified and as directed.

S&F in repairs pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' & 'Cold' with long screwed shanks and fly nuts, screwed for 15 mm bore iron pipe complete all as specified and as directed .

S & F in repairs, stop valves, 25 mm dia, cast copper alloy with capstan head, screwed down high pressure with crutch or butterfly handle with long shank and cup [concealed type] for iron pipe etc., complete all as specified and as directed.

S&F in repairs 15 mm dia angular stop cock, chromium plated brass body, fancy type, with long thread with flange, complete all as specified and as directed.

S&F in repairs 15 mm dia two way angular cock, chromium plated brass body, fancy type, with long thread with flange, complete all as specified and as directed.

S & F in repair Bidet spray (Health faucet) with 1 meter SS tube and holder, complete all as specified and as directed.

S& F in repairs 15 mm dia (concealed type) stop cock, fancy type, chromium plated brass body, regular body with adujstable wall flange, complete all as specified and as directed.

S& F in repairs 15 mm dia bib cock, fancy type, chromium plated brass body, regular body with adujstable wall flange, complete all as specified and as directed.

Supply only 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia complete all as specified and as directed.

S&F Rotational moulded polythene water storage tanks of 1000 ltrs capacity, white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I with PTMT ball valve heigh pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms including dismantling old u/s existing tanks complete all as specified and as directed.

M&L 50 mm thick plain cement concrete, 1:2:4 type B0 using 12.5mm graded stone aggreage, as in platform for water tank on roof slab etc., including necessary form work complete all as specified and directed.

Demolition of reinforced cement concrete such as roof, floor slab, beams, stair case, landing, chajjas, column, beams, and similar suspended work and removing rubbish to out side MD land complete all as specified and as directed.

S&F 7.5-10 cm thick pressed machine cut sand stone slabs Jodhpur pattern/colour in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc not exceeding 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar (1:3) complete all as specified & directed

M&L roughly squared stone lintels hammer dressed on face and soffits,hoisted, set and pointed in cement mortar 1:6 complete.n exc 3m in length complete all as specified & directed

M & L 75mm thick rough dressed sand stone slab of minimum 1mtr in length laid bedded and jointed in CM 1:6 and pointed in CM 1:3 laid over and including 25mm thick PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate complete all as specified and directed.

M&L sand stone slabs in sunshades, chajjas, shelves, cills, landings cover stones templates etc n exc 2m in length punched dressed on face and along exposed edges self faced on other side and set and pointed in cement mortar 1:4 thickness of slab 5cm complete

Supply only Integral water proofing compund ISI Marked, complete all as specified and directed.

Taking up or down 25mm bore steel tubing and connections including cleaning for refixing or credited to contractor complete all as specified and as directed.

All as per item No. 113.00 here-in-above, but 20 mm bore pipe

All as per item No. 113.00 here-in-above, but 15 mm bore pipe

Refixing old GI water tubing of 15 mm bore, medium grade including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including taking up or down 25mm bore steel tubing and connections complete all as specified and as directed.

All as per item No. 116.00 here-in-above, but 20 mm bore pipe

All as per item No. 116.00 here-in-above, but 15 mm bore pipe

S&F GI tubing (ISI marked) 25mm bore medium grade with all fittings and fixed to walls and ceiling or laid in floors and connections complete all as specified and as directed.

All as per item No. 119.00 here-in-above, but 20 mm bore pipe

All as per item No. 119.00 here-in-above, but 15 mm bore including cutting chases, pinning in & making good to disturbed portion to match the existing surface etc complete.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including fair finished surfaces complete all as specified and directed.

Use and waste formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide includingrough finished surfaces complete all as specified and directed.

Use and waste of form work to sides and soffits of lintels, beams, brackets, shelves and similar works for rough finished surfaces of concrete complete all as specified and as directed.

M&L RCC M-25 design mix as in slabs supported on walls, beams and colunms in floors,roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L RCC M-25 design mix as in beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed.

S&F TMT bar 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

S&F mild steel TMT bar 6 to 8 mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

Complete removal of existing water proofing treatment of any description including bedding up to the true surface of original concrete, in RCC roof slab / stone patty and roughening the old surfaces by picking, sweeping clean and washing down with water to remove dust etc including removing rubbish to out side MD land and provide plastring 10 mm thick in CM (1:4) finished even & smooth over the RCC roof slab / stone patty for laying of water proofing treatment using water proofing compound (WPC) as per manufacturer instructionand including providing the following as roof treatment complete all as specified and as directed : - (a) FIRST COURSE: Applying a coat of bituminous primer @ 0.4 litre / Sqm manufactured by the same agency that of APP with a density 0.87 to 0.89 Kg/litre at 25 degree celsius on prepared plastred surfaces. (b) SECOND COURSE: Applying one coat of bonding material using blown type bitumen conforming to IS-702 grade 85/25 @ 1.20 Kg/Sqm (c) THIRD COURSE : Provide a layer of APP modified polymeric membrane centre core of 100mm micron HMHDPE, outer film 20 micron each, thickness 3.00mm having weight not less than 3.00 Kg/Sqm using butane torch with minimum 10cm side lap and 15cm end lap complete (d) FOURTH COURSE : Applying one coat of bonding material using blown type bitumen confirming to IS- 702 grade 85/25 @ 1.20 Kg/Sqm. (e) FIFTH COURSE : M&L 40mm thick PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate in roof padding , the surface of concrete is to be finished even and fair with out using extra cement NOTE :- WPC shall be measured and paid separately under respective

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete, including unserviceable fixture and fittings such as switches, ceiling rose, holder, pendents, regulators, sockets, light fittings etc . & removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls,floors, etc, complete all as specified and directed.

Taking down un-serviceable DB of any size and capacity including MCB etc, and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls,floors, etc, complete all as specified and directed .

M&L Point wiring using approved colour coding as per IS (Red , Black and Green for single phase circuits),with multi stranded copper conductor, nominal cross-sectional area is 1.5 sq mm , single core, PVC insulated and unsheathed FRLSH cable 1100 Volts grade, ISI-694 marked with valid CML No.in and including heavy duty drawn through and including in non mettalic heavy duty PVC rigid conduit with all accessories complete concealed in wall/roof/floor etc, including cutting, chasing, pinning & making good disturbed surfaces as per existing, ISI marked with1.6mm thick mild steel/prestressed steel sunken/concealed box (with earth dolly) duly painted two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally and two coats of black bituminous paint over a coat of red oxide primer externally, with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, inciuding PVC insulated multistranded copper conductor 1.5 sq mm nominal cross sectional area single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly for,one way switch One light/ fan/bell point controlled by one, one way switch complete all as specified and directed .Note:- surface conduit shall be laid in ceiling portion only.

All as per Serial Item No.132.00 above but for one 3 pin socket outlet 5 Amps on the same board with other switches.

All as per Serial Item No. 132.00 above but one 3 pin socket outlet 5 Amps on independent board complete all as specified and as directed.

All as per serial Item No.132.00 above but for 15 Amps 5/6 pin socket point on independent board with 4.00 Sqmm PVC insulated FRLS multi-stranded copper conductor with 4.00 Sqmm PVC insulated FRLS multi-stranded copper conductor as earth wire complete all as specified and directed .

M&L Switch piano type 5/6 Amps, single pole, flush type, one way, complete all as specified and as directed.

M&L Switch piano type 15 Amps, single pole, flush type, one way, complete all as specified and as directed.

M&L Socket outlet, 2 in 1, 5 and 15 Amps, flush type, universal ,230 Volts controlled by one switch complete all as specified and as directed.

M&L Ceiling rose, 3 phase / PVC / Polycarbonate, isolated bodycomplete all as specified and as directed.

S&F Lamp holder, PVC / poly carbonate type with black plate suitable for batten fittings, including 9W lamp complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply, fixing, testing & commissioning LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supply, fixing, testing & commissioning LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

Supply, installation, testing & commissioning of desert cooler electric driven (single phase) three speed having nominal air flow capacity 5000 CFM per hour, with propeller ISI marked cooler fan motor copper winding single phase fitted with having aluminium blade of minimum size 500 mm, submersible pump, Max power consumption of 325 watts, cooler body made out from 20 gauge mild steel galvanized iron sheet & water tank made out 18 SWG with 40 Ltr min capacity, including three louvers with wood wool pad, flexible PVC distribution pipes connected to 3 way junction, complete all as specified and directed. Note:- The quoted rated are deemed to inclusive of of following items:- (i)- 1 nos Three speed rotary type switch (ISI marked) for propeller fan and 1 nos one way switch to control pump. The switches shall have marking off- Low- medium- High. (ii)- Float valve on water supply connection

Supply, installation, testing and commissioining of electric storage geyser of capacity 25 litre, BEE 5 Star rated , 230Volts, AC, 50Hz, comprising of heating element 2000 watt, steel body with copper inner tank, puff insulation,both power indicating LED lamp and heating indicating LED lamp neccasry suitable 3 core copper cable, suitable plug top, complete with all accessories such as safety valve, thermostate, NRV, connection piece etc., inlcluding supply and fixing of inlet and out let connection to geyser with steel grip,chromium plated PVC connection of 600mm in length - 02 Nos (one for inlet GI pipe and other one for outlet connection) suitable to connect inlet GI pipe 15mm dia and out let GI pipe 15mm dia (out let PVC connection should be capable to withstand the designed temparature of Geyser) and geyser shall be fixed on wall surface with wall mount bracket and 10 cm anchor bolts as required inclduing all necessary plumbling works and civil works complete all as directed and as specified.

Supply, fixing, testing and commissioning MCB SPN 40 Ampsrating 240V, 10KA 'C' curve and current carrying capacity in the MCB DB complete with connection, complete all as directed and as specified.

M&L MCB SP ‘B’ Curve 10KA , 6-30 amps 230V complete all as specified and as directed .

M&L Factory made distribution board in sheet metal enclosure in double door with 200A rated bus bar,SPN 12 way, 240V for fixing MCB's, including cutting, chasing & pinning & flashing to wall surfaces and making good as per existing, complete all as specified and as directed.

M&L Factory made distribution board in sheet metal enclosure in double door with 200A rated bus bar,SPN 4 way, 240V for fixing MCB's, including cutting, chasing & pinning & flashing to wall surfaces and making good as per existing, complete all as specified and as directed.

Taking down existing earthing and M&L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 5 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron 15 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of strata, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed by Engineer-in-charge. NOTE :(i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 5 of MES SSR Part Item includes the cost of GI pipe up to 7.5m for protection of earth wire. Any variation in length beyond 7.50 m shall be measured separately. (iii) Item includes cost of lead wire up to 7.5 m Any variation in length beyond 7.50 m shall be measured separately. (iv) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate.

Supply, laying, testing & commissioining LT UG cable XLPE insulated screened PVC beded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 Sqmm 2 core, including clamping accessories wherever required complete all as specified and as directed. Note:- Earthwork, sand cushioing, GI pipe & PCC cover shall be measured and paid seperately.

Excavation in trenches not exceeding 1.5mtr wide and not exceeding 1.5 mtr in deep for foundation of pole, laying of cable etc, and getting out in any type of soil complete all as specified and as directed .

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick in any type of soil complete all as specified and as directed.

Removing excavated materials to a distance not exceeding 50m depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Supply and spreading tibba sand in trenches for cushioning to PVC cable and punning to provide required cover to UG cable complete all as specified and directed .Note :- Punned thickness shall be measured for the purpose of payment.

Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1 flat, size 300mm x 180mm x 40mm, complete all as specified and directed.

S&F GI tubing , light grade of 40mm bore with fittings fixed to wall / pole / floor for cable protection including clamping of pipe with MS flat of size 50X5mm including nut, bolt & washers of size 50X12mm whereever required complete all as specified and as directed.

Supply, Installation, testing & commissioning of Split type air conditioner electric driven (single phase), cooling capacity 1.5 Ton BEE 5 Star rating, including M&L all acessoseries like copper tubes with insulation puffs, drainage pipe of required length as per site requirement, stand for mounting the outdoor unit on wall/roof & etc., complete all as per specified & directed.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 150 V to 290 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 4 KVA, complete all as specified and as directed.

M&L submain wiring with two runs of 2.5 sqmm with one run of 2.5 Sqmm earth wire of 1100V grade FRLSH PVC insulated multi-stranded copper conductor, single core cable conforming to IS 694 drawn through and including cutting chasing in wall for concealed using machine cutting and making good and M&L 20mm dia non mettalic PVC rigid conduit with wall thickness not less than 1.8 mm, accessories concealed on wall / ceiling with PVC saddles and cadmium plated steel screws and connected to common earth dolly complete all as specified and directed. Note :- Three runs of 2.5 sqmm and one run of PVC conduit shall be measured as one length for the purpose of measurement.

Supply, fixing, testing and commissioning SP 20 Amps 240V 10KA 'C' curve miniature circuit breaker (MCB) and current carrying capacity in the DB complete with connection, complete all as specified and as directed.

Single pole and neutral enclosure with 2 pin earth industrial plug and socket with one MCB SPN 32 Amps, complete all as specified and directed.

NOTE:- (i)- Quantities are clubbed in BOQ for different Jobs. For which ref., as below:- (a)- 09/SR (BLDG)/JODH/2023-24 (Item No. 1.00 to 157.00) (b)- 04/LBW/JODH/2023-24 (Item No. 158.00 to 162.00 (ii)- The contract sum shall be arrived at after duducting amount of schedule of "Credit" from the Total quoted amount

GANGADHAN ENTERPRISES