PROVISION OF WAITING SHED AND ACILLARY SERVICE FOR TMC AT NAGROTA UNDER GE (P) NAGROTA

BR PORTION Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm

M&L Cement concrete Type D2 1:4:8 (40mm graded crushed aggregate) in foundations,filling and mass concrete

M&L PCC 1:3:6,Type C2 using 40mm graded stone agg as in foundation/fencing post fixing all as specified and directed.

Removing excavated material up to a distance exc. 250 m but n exc. 500 m and depositing where directed

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed.

M&L for applying two coat of synthetic enamel paint on new or previously untreated steel surfaces exc 10 cm width or girth over a coat of red oxide zinc chrome primer including preparation of surfaces complete all as specified and directed.

S&F 0.5mm thick (total coated thickness) Pre colour,pre- profiled galvalume sheets of required colour and design having tensile strength 550 Mpa as in roof,wall cladding,north light curves, fixed with zinc coated self drilling fastner including EPDM washer complete laid with one corrugation side laps and min 150mm and lap laid to slope all as per manufacturer/profile maker instruction complete all as specified and directed.

Excavating over areas in hard and dense soil, n exc 1.5 m deep and getting out complete all as specified and directed.

M&L Plain Cement concrete type D- 2, 1:4:8 (40mm graded aggregate )75mm thick as in sub base of floor complete all as specified and directed.

S&F for 60 mm thickness Machine pressed precast concrete interlocking paver (glossy finished) of M-35 Grade approved shape and size and colour confirming to IS 15658-2006 and laid over 25mm thick sand cushion complete all as specified and directed. Note:-Shape and colour approved by GE.

Supply only fine aggregate complete all as specified and directed.

M&L for precast cement concrete type B-1(1:2:4) ( 20mm graded stone agg) as in kerb and edging to road and foot path,etc including chamfered weathering,thorating etc. and setting in CM(1:4) complete all as specified and directed.

Demolition Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 Complete all as specified using old size bricks

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished & smooth without using extra cement complete all as specified.

Verified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or colored cement to match the shade of tiles over and including 15mm thick screed bed in CM 1:4) complete all as specified & directed.

All as per item No above but on vertical surfaces such as skirting/dados including 10mm thick rendering in CM (1:4) as in backing coat complete all as specified and directed.

M&L glazed, ceramic colored tiles of size (350x250x7mm/300x450x7mm thick), set and jointed neat cement slurry and pointed in white or colored cement to match with the surface and including 15mm thick rendering coat in CM 1:4 as in backing coat complete all as specified and directed.

S&F Anodised aluminium snap grid frame work for false ceiling E board size 600x600mmx6mm,inserted in GI/Aluminium frame as in ceiling main Tee section of size 36.5mmx25mmx1.4mm thick, cross Tee section of size 23.5mmx26.4mmx1.4mm thick, supported at ends all along the wall with aluminium anodised anhle of size 40mmx25mmx2mm thick and 4mm dia GI suspenders complete all as specified and directed.

S&F Powder coated aluminium frame work for doors, windows, ventilators and partitions (sliding/openable/Fix doors/ windows,ventilators) etc with one, two or more rebates (reqd as per site), section weighing not less than 0.55 kg/m, including joining cleat for fixing with dash fasteners of required dia and size,incl filling up gaps at junctions, ie top, bottoms and sides etc. complete all as specified and directed.

S&F aluminium powder coated door shutters (sliding/openable/fixed as per requriement of site), aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc.(Thickness or powder coating not less than 50 micron). complete all as specified.

S&F powder coated aluminium window and ventilator shutters,sliding/openable/as per requriement of site) type without sash bar, aluminium section weighing 0.55 kg/m including necessary locking arrangement,guide wheels, joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F Sheet glass plain/colored ( as per directed by Engr-in-Charge)3mm/5mm thick best quality and glazing with rubber packing, screw or glass putty in square n exc 0.5 sq. m in each pane complete all as specified.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, with wooden grain printed PVC sheet used inserted of plain colour PVC sheet &edges will be painted to match with printed sheet complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick(size not less than 550x550mm) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing finished laid over and including 20mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L for machine cut Kota stone slab flooring 18-20mm thick in riser of steps, skirting, dado and pillar over including 10mm thick 1:4CM backing coat on vertical surface of wall with rubbing and mirror polishing finished complete all as specified and as directed.

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with providing 15mm thick screed bed i cement mortar 1:4 complete all as specified and as directed.

M&L for preparing new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant cement primer and over a cost of 2 to 3mm thick wall care putty complete all as specified and directed.

M&L for preparation of old decorated plastered or un plastered surface including complete removal by brooming down with steel wire brushing, scraping down smoke soot,moulded, moss, efflorescent salt, trading oil and greasy spot and applying two coat of oil bound distemper on walls over 2mm thick plaster of Paris putty as specified and directed by Engr-in-charge.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for formwork fair and finished surfaces to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs,etc. also splays between floors and beams, etc complete all as specified and directed.

M&L RCC M-25 using 20mm graded stone agg as in Beams, cantilevers, bressummers, lintels over 1.5m span deck slab and in drain cover slab, shelves and similer work etc. complete all as specified and directed.

EM PORTION M&L for Point wiring for One light point controlled by one switch 5 Amp SP one-way complete with 1.5 Sq mm (nominal area) PVC insulated, unsheathed and multi strand copper conductor FRLS cable (ISI marked) drawn into and including PVC concealed conduit (medium grade) and conduit fittings including 1.5 Sq mm PVC insulated unsheathed and multi stranded copper conductor FRLS cable as earth wire to common earth and connecting to earth dolly, MS modular sunken box of suitable size for fixing modular switches,sockets,regulators including modular cover plate (inner/outer) of size as per site requirement and machine made brass screw and washers etc complete all as specified and directed for one light point controlled by one one way switch complete all as specified and directed by Engr-in-Charge..

Ditto - all as per item No. 36 above but for one ceiling fan/exhaust/wall fan point.

Ditto - all as per item No. 36 above but for one 3 pin 5 amp socket outlet on same board.

Ditto - all as per item No. 36 above but for one 3 pin 5 amp socket outlet on indipendant board.

Ditto - all as per item No. 36 above but point wiring with FRLS multi stranded copper conductor cable of size 2.5 sqmm for 15 amp socket outlet including 2.5 sqmm earth continuity conductor complete all as specified and directed by Engr-in-Charge.

Ditto - all as per item No. 36 above but point wiring with FRLS multi stranded copper conductor cable of size 4.0 sqmm for main circuit and 4.0 sq mm sqmm for earth continuity conductor ( for geyser ) complete all as specified and directed by Engr-in-Charge.

S & F Modular switch SP one way 5/6 Amps suitable for 1 Module complete all as specified.

S & F Modular socket 5 pin 5/6 Amps suitable for 2 Module complete all as specified.

S & F Modular switch SP one way 15/16 Amps suitable for 1 Module complete all as specified

S & F Modular socket 3 pin 15/16 Amps suitable for 2 Module complete all as specified.

S& F Modular fan regulator 2 module complete all as specified & directed.

S& F Modular blanking plate 1 module complete all as specified & directed.

S& F Supply and fixing MCB protected PVC modular box incl modular socket 15 amp and one single pole modular MCB of 20 amp complete all as specified and directed by Engr-in-Charge.

S & F ceiling rose surface backalite of suitable size three terminals complete all as specified

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

Supply and fixing LED lights fitting 22 watt, 220V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC, warm white/cool white/white , recess mounted with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED building security light fitting 25 Watt 230 V AC outdoor type with pressure die cast aluminum housing and heat resistant complete with driver, lumen efficiancy not less than 110Lm/watt with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection , including bracket made up of 40 mm dia GI pipe light grade of length not less than 1.5 mtr , bracket 2 nos with nut bolt for fixing on wall dully painted with one coat of red oxide followed by two coats synthetic enamel paint of aluminium colur complete all as specified and directed by Engr-in-Charge. .

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) all as specified and directed.

Supply and fix exhaust fan, steel body heavy duty AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers all as specified and directed by Engineer- in-Charge.

Supply and fix electric water heater,storage type steel body with glass lined steel inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection with three core PVC insulated flexible copper conductor cable including three pin plug top etc complete all as specified and directed by Engr-in-Charge.

S & F VTPN (Vertical Loadline) DB suitable for MCCB up to 125 amp as incomer , fitted with suitable size of bus bars , neutral Links, earthing link, Blanking Plates , double door IP-43 protection including MCCB 125 amp as inclomer complete all as specified and directed by Engr-in-Charge.

Supply and fixing sheet metal enclosure distribution board SPN 12 way, double door, IP43 protection, powder coated including shrouded neutral, earth bar, DIN link and 200 amp bus bar complete all as specified and directed by Engr-in-Charge.

Supply and fixing MCB SP 240 Volts 5 Amps to 32 Amps complete all as specified and directed by Engineer-in Charge.

Supply and fixing MCB SPN 240 Volts 40 to 63 Amps complete all as specified and directed by Engineer-in Charge.

S & F Sub main wiring with PVC insulated, FRLS cable 2 single core 6 Sq mm 1100 V grade with stranded copper conductor on and incl PVC rigid non metalic conduit (ISI marked) in concealed incl all specials like joint, elbow , Tee ,junction , bend etc and provision of PVC insulated copper conductor single core 6 sq mm for earth continuityconductor complete all as directed by Enginer-in-charge.

M&L for earthing complete with GI earth plate 60cm ×60cm ×3 mm thick electrode buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meter below normal ground level connected to GI earth wire lead 4 mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or steel all as shown in electrical plate No 3 of SSR Part-I connected to continuous earth wire on earthing point all as specified and testing on completion, including provision of GI earth lead wire protected by 15 mm dia GI light grade protection pipe from test point to main board and 20mm GI medium grade watering pipe funnel, PCC earth pit and RCC cover charcoal, salt and GI wire including excavation and earth work etc complete all as directed by Engr-in-charge