REPAIRS AND MAINTENANCE OF FURNITURE UNDER AGE (I) (CG) VIZAG

Amount

Removal of existing broken/unserviceable front leg of Chair dining and replacing the same with new front leg 1st class hard wood (Teak) (size & dimension of the parts shall be of the same pattern/size as shown in drawing as well as specification) and applying two coats of french polich to all the replaced parts to match with existing after proper preparation of surfaces completely all as specified and directed. (FD-279) Note:- All furniture repair works shall be carried out at various units /locations / BSO yard as per the direction of Engr in charge. Quoted rate shall be deemed to be inclusive of all subsequent expenditure occured on carriying out repair at various sites/locations and nothing extra on account of any misunderstanding or otherwise on this account shall be admissible.

All as per Item No. 1 above but replacing the rear leg of Chair Dining. (FD-279)

All as per Item No. 1 above but replacing the back rest/bend stiffner of Chair Dining. (FD-279)

All as per Item No. 1 above but replacing the front/side/back rail of Chair Dining. (FD-279)

All as per Item No. 1 above but replacing the bottom stiffner of Chair Dining. (FD-279)

Removal of existing broken PVC shoe from all legs and replacing with new PVC shoe (set of four) of suitable size to legs of Chair Dining complete as shown in drawing and as specified (FD-279)

M&L for fixing MS right angle of size 50x25x5 mm thick on any one corner of Chair Dining by screwing to side rail and leg of Chair all as directed by Engr in charge (FD-279).

M & L for preparation of old treated wooden surfaces of Chair Dining as per drawing No (FD-279) and applying two coats of french polish complete all as specified and directed.

M&L for removal of existing broken / unserviceable front /back/ side rail of Chair dining cushioned, replacing the same with new teak wood front/back/side rail, size & dimension of the parts shall be of the same pattern/size as shown in drawing as well as in specification, fixed to main frame and legs of chair dining cushioned and apply two coats of french polich to all replaced parts to match with existing all as specified and directed (FD/E6/MAP/10(R), FD/MAP-II/04).

All as per Item No. 9 above but replacing the front leg of chair dinning cushioned (FD/E6/MAP/10(R), FD/MAP-II/04).

All as per Item No. 9 above but replacing the back stiffner of chair dinning cushioned (FD/E6/MAP/10(R), FD/MAP-II/04).

M&L for removal of old unserviceable seat of chair dining cushioned and fixing new cushion of 75mm thick, 28 density foam seat, covered with fabric of approved colour fixed to 12mm thick commercial plywood seat of Chair Dining cushioned, complete all as specified and directed (FD/E6/MAP/10(R), FD/MAP-II/04).

Removal of existing broken PVC shoe from all legs and replacing with new PVC shoe (set of four) of suitable size to legs of Chair Dining Cushioned as shown in drawing and as specified (FD/E6/MAP/10(R), FD/MAP-II/04).

M&L for fixing MS right angle of size 50x25x5 mm thick on any one corner of Chair Dining cushioned by screwing to side rail and leg of Chair all as directed (FD/E6/MAP/10(R), FD/MAP-II/04).

M & L preparation of old treated wooden surfaces of Chair Dining cushioned as per drawing No (FD/E6/MAP/10(R), FD/MAP-II/04). and applying two coats of french polish complete all as specified and directed.

Removal of existing broken/unserviceable front/rear leg of Chair easy and replacing the same with new front/rear leg 1st class hard wood (Teak), size & dimension of the parts shall be of the same pattern/size as shown in drawing as well as specification and applying two coats of french polish to all replaced parts to match with existing all as specified and directed (FD-229 & 201)

All as per item No. 16 above but replacing arm rest of Chair easy (FD-229 & 201)

All as per item No. 16 above but replacing front/rear/back rail of seat frame of Chair easy (FD-229 & 201)

All as per item No. 16 above but replacing top / bottom/side rail of back rest frame of Chair easy (FD-229 & 201)

M&L for removal of existing broken PVC shoe from all legs and replacing with new PVC shoe (set of four) of suitable size to legs of Chair easy as shown in drawing (FD-229/201)

M&L for fixing wooden right angle corner bracket of size 75x25 mm thick on any one corner of Chair easy by screwing to side rail and leg of Chair all as directed (FD-229/201)

M & L preparation of old treated wooden surfaces of Chair Easy and applying two coats of french polish complete all as specified. (FD-229/201)

M & L for preparation of old treated wooden surfaces of Hat stand and applying two coats of french polish complete all as specified. (FD-233)

M&L for removing broken aluminium peg hooks and new anodised aluminium peg hooks 75 mm long fixed to the Hat stand with mirror (FD-233) all as specified and as directed

M&L for removal of existing foggy/broken mirror of Table dressing gents and replacing the same with new mirror not less than 5.0 mm thick and of size 380 x 760 mm and fixing on the existing frame all as shown on drg and as specified. FD -230

M&L for removal of old broken plywood back of mirror of Table dressing gents and replacing the same with new 6 mm plywood fixing to the existing frame alongwith 35x25 mm wooden beading alround all as shown on drg and as specified. FD -230

M&L for removal of old broken particle board top/bottom of Table dressing gents drawer and replacing the same with 18 mm prelaminated particle board of size 900x300 of same colour & texture of exisiting item complete all as shown on drg and as specified. FD -230

M & L preparation of old treated wooden surfaces of Table dressing Gents and applying two coats of french polish complete all as specified and directed. (FD/MAP-II/07)

M&L Fixing new Table dressing Gents/ Hat stand with mirror on the wall at various locations with suitable MS screws over a wooden / PVC plug as per directions of Engr in charge (FD-233 & FD-230)

M&L for removal of existing foggy/broken mirror of Table dressing Ladies and replacing the same with new mirror not less than 5.0 mm thick and of size 430 x 1230 mm and fixing on the existing frame all as shown on drg and as specified. FD/E6/MAP II/07

M&L for removal of old broken plywood back of mirror of Table dressing Ladies and replacing the same with new 6 mm plywood fixing to the existing frame alongwith 25x20 mm wooden beading alround all as shown on drg and as specified. FD/E6/MAP II/07

M&L for removal of seat cushion of Table dressing Ladies with mirror FD/E6/MAP II/07 and supply new foam cushion 75 mm thick having 32 density duly stitched with tapestry cloth not less than 240/- per meter over 12 mm thick commercial plywood seat base all as shown in drg and as specified (FD/E6/MAP II/07)

M & L preparation of old treated wooden surfaces of Table dressing Ladies and applying two coats of french polish complete all as specified and directed. (FD/MAP-II/07)

M&L for removal of existing damaged top of Peg table and replacing the same with new top 18mm thick prelaminated particle board 450 x 300 mm size with one side decorative teak finish including 18mm wide, 4 mm thick teak wood edging on all sides incl french polishing teak wood edging and as shown in drg and as specified. (FD-277, FD-384)

M&L for removal of existing damaged any one leg of Peg table and replacing the same with new leg in 1st class hard wood (Teak). Size & dimension of the parts shall be of the same pattern/size as shown in drawing as well as specification and apply two coats of french polich to all replaced parts to match with existing all as specified and directed by Engineer-in-Charge (FD - 277, FD-384)

All as per item No. 35 here-in-above but replacing long rail of Peg Table (FD - 277, FD-384)

All as per item No. 35 here-in-above but replacing short rail of Peg Table (FD - 277, FD-384)

M & L preparation of old treated wooden surfaces of Peg table and applying two coats of french polish complete all as specified and directed (FD - 277, FD-384)

SOFA SET 5 SEATER,(3+1+1) (FD - 234/ FD-281) :- Removing old broken leg from sofa chair carefully without damaging the other parts ,supply and fixing new leg of size 70mmx35mmx495mm made of 1st class teak wood using screws only with proper workmanship.complete all as specified, shown on drawing and as directed.

Removing old broken arm from sofa chair carefully without damaging the other parts ,supply and fixing new arm of size 70mmx35mmx745mm made of 1st class teak wood using screws only with proper workmanship.complete all as specified ,shown on drawing and as directed.

Removing old broken wooden batten from sofa chair carefully without damaging the other parts ,supply and fixing new wooden batten of size 50mmx20mmx580mm made of 1st class teak wood using screws only with proper workmanship.complete all as specified ,shown on drawing and as directed.

Removing old broken long wooden rail from sofa chair carefully without damaging the other parts ,supply and fixing new wooden rail of size 100mmx35mmx1630mm made of 1st class teak wood using screws only with proper workmanship.complete all as specified ,shown on drawing and as directed.

Removing old broken short wooden rail from sofa chair carefully without damaging the other parts ,supply and fixing new wooden rail of size 100mmx35mmx625mm made of 1st class teak wood using screws only with proper workmanship.complete all as specified ,shown on drawing and as directed.

Taking out old pressed /torn cushions from each set and Supply of 32 density ,100mm thick PU foam cushion of size 520mmx560mmx100mm duly covered with inner linen cloth and best tapestry cloth not less than Rs 400 per metre of approved color and shade. Each cushion cover shall be provided with best quality polyester zipper stitched on one edge of cushion cover covered under the flap of cloth with standard fitting. Tapestry cloth:- It shall be heavy linen look fabric ,plain velvet fabric or as per approved sample placed in BSO yard . Make of Foam 32 density-Kurlon-goldline plus/Sleepwell-primo/U-foam

Scratching the entire wooden pallets of sofa with sand emery paper of various grit , filling the pores with wood filler to make good the surface,After prepartion of surface the entire sofa chair shall be polished in melamine finish in high gloss with spary machine only. Make of French polish- Asian paints/Berger paints

SOFA SINGLE SEAT (FD - 234/ FD-281) :- Removing old broken legs from sofa chair carefully without damaging the other parts ,supply and fixing new legs of size 70mmx35mmx495mm made of 1st class teak wood using screws only with proper workmanship.complete all as specified ,shown on drawing and as directed.

Removing old broken arms from sofa chair carefully without damaging the other parts ,supply and fixing new arm of size 70mmx35mmx745mm made of 1st class teak wood using screws only with proper workmanship.complete all as specified ,shown on drawing and as directed.

Removing old broken wooden battens from sofa chair carefully without damaging the other parts ,supply and fixing new wooden battens of size 50mmx20mmx580mm made of 1st class teak wood using screws only with proper workmanship.complete all as specified ,shown on drawing and as directed.

Removing old broken side wooden rails from sofa chair carefully without damaging the other parts ,supply and fixing new wooden rails of size 100mmx35mmx625mm made of 1st class teak wood using screws only with proper workmanship.complete all as specified ,shown on drawing and as directed.

Taking out old pressed /torn cushions from each set and Supply of 32 density,100mm thick foam cushion of size 520mmx560mmx100mm duly covered with inner linen cloth and best tapestry cloth not less than Rs 400 per metre of approved color and shade. Each cushion cover shall be provided with best quality polyester zipper stitched on one edge of cushion cover covered under the flap of cloth with standard fitting. Tapestry cloth:- It shall be heavy linen look fabric ,plain velvet fabric or as per approved sample placed in BSO yard . Make of Foam 32 density-Kurlon-goldline plus/Sleepwell-primo/U-foam

Scratching the entire sofa with sand emery paper of various grit , filling the pores with wood filler to make good the surface,After prepartion of surface the entire sofa chair shall be polished in high gloss with spary machine only. Make of French polish-Asian paints/Berger paints

SIDE BOARD,FD-1112:- Scratching the entire wooden beading of side board, filling putty to the bore holes making surface smooth by scratching it with sand emery paper and French polish with high gloss finish, after properly cleaned and smoothened the surface.

BIN LINEN MULTIPURPOSE,FD/E6/MAP/09 :- Scratching the entire wooden beading of bin linen multipurpose , filling putty to the bore holes making surface smooth by scratching it with sand emery paper and French polish with high gloss finish, after properly cleaned and smoothened the surface.

TABLE DINING FOR 6 PERS/ 4 PERS ( FD/E6/MAP-II/03, FD-273):- Top of size 1500mmx900mm / 1200X900mm made out of 18/19mm thick prelaminated particle board exterior grade, natural teak color, edges duly covered with 4 mm thick beading of teak wood

Legs made of 1st class teak wood as per size on drg

Long rail made of 1st class teak wood as per size on drg

Short rail made of 1st class teak wood as per size on drg

Corner Shape wooden bracket of size 4" x 4" and 35mm thick shall be fixed to legs and rail with adhesive and screws.(08 X Nos in each table)

Scratching the entire table, filling putty to the bore holes making surface smooth by scratching it with sand emery paper, it shall be French polish with high gloss finish ,after properly cleaned and smoothened the surface.

M&L for removing existing broken / unserviceable leg of Teapoy FD -278, replacing the same with new leg Ist class hardwood (Teakwood) of size & dimention of the parts shall be of the same pattern / size as shown in drawing as well as specified and apply two coats of french polish to all replaced parts to ,match with exisitng all as specfied and directed by Engr - in - charge

All as per Sl item No. 60 here-in-above, but replacing long rail of Teapoy. FD-278

All as per Sl item No. 60 here-in-above, but replacing short rail of Teapoy. FD-278

M & L preparation of old treated wooden surfaces of Teapoy and applying two coats of french polish complete all as specified and directed

M&L for removing existing broken / unserviceable leg of Table centre (FD-274) replacing the same with new leg Ist class hardwood (Teakwood) of size & dimention of the parts shall be of the same pattern / size as shown in drawing and apply two coats of french polish to all replaced parts to match with exisitng all as specfied and directed by Engr - in - charge

All as per Sl item No.64 here-in-above but replacing long rail of Table centre. FD-274

All as per Sl item No. 64 here-in-above but replacing short rail of Table centre. FD-274

M & L preparation of old treated wooden surfaces of Table centre and applying two coats of french polish complete all as specified and directed

M&L for removing existing broken / unserviceable leg of Table writing FD-275 replacing the same with new leg Ist class hardwood (Teakwood) of size & dimention of the parts shall be of the same pattern / size as shown in drawing and apply two coats of french polish to all replaced parts to match with exisitng all as specfied and directed by Engr - in - charge

All as per Sl item No. 68 here-in-above, but replacing long rail of Table writing. FD-275

All as per Sl item No. 68 here-in-above, but replacing short rail of Table writing. FD-275

M&L for removal of existing damaged shutter of the table shelf of Table writing and replacing with new shutter 18mm thick one side teak veneered with 4mm thick teak wood beading alround fixed to the side with Piano hinges of MS and the shutter provided with a recessed handle 50 x 38 mm and also cupboard lock with duplicate keys including french polishing teak veneered surface and TW beading and fixed complete all as shown in drg and as specified. FD-275

M&L for removal of existing damaged drawer of Table writing complete and replacing with new drawer of 18 mm prelaminated particle board and back plank base shall be 6mm thick commercial plywood and the drawer to be provided with a new recessed type handle 50 x 38 mm embedded in the drawer face, exposed portion duly french polished all as shown in drg and as specified. FD-275

M & L preparation of old treated wooden surfaces of Table writing and applying two coats of french polish complete all as specified and directed

M&L for removing unserviceable handle of Almirah steel medium / Almirah large steel/ Almirah half hanging replacing with Brass chromium plated handle, 100 mm long, as per Godrej Pattern. (FD-1032/1034 /FD/MAP/18) (Note:- The repair work shall be carried out at various units / BSO yard as per the directions of Engr in charge. Rate shall be inclusive of all subsequent expenditure incurred for carrying out repair work at various units)

M&L for One side leg of Almirah steel medium / Almirah lagre steel / half hang (FD-1032 / 1034/ FD/MAP/18)), left or right, 70 mm wide and 100 mm high, open ends bent outwards upto 15 mm, MS sheet of 1.6 mm thick, welding the channel to bottom of almirah at 50 mm from the side of almirah including 2 coats of synthetic enamel paint TA grey colour or colour as directed by Engineer-in-Charge

M&L for 3 way locking device as per Godrej pattern, fully operational with the existing handle. (FD-1032/1034 / FD/MAP/18))

M&L Steel cup board lock, 50 mm size, 6 lever with stainless steel keys in duplicate as per Godrej pattern. (FD-1032/1034/ FD/MAP/18))

M & L preparation of old treated steel surfaces of Almirah medium with shelves / Almirah half hang as per drawing No. FD-1032 / FD-1034 and applying a coat of synthetic enamel paint colour as directed by Engineer-in-Charge.

M & L preparation of old treated steel surfaces of Almirah large Steel as per drawing No. FD/E6/MAP/18 and applying a coat of synthetic enamel paint colour as directed by Engineer-in-Charge.

Removing the existing unserviceable/damaged door carefully by removing the hinges of Almirah large Steel and supply and fixing new shutter made of 1 mm thick MS sheet of same size and shape to almirah large steel. Complete all as directed and shown on drawing. (FD/MAP/18)

Removing the existing unserviceable/damaged door carefully by removing the hinges of Almirah Medium Steel and supply and fixing new shutter made of 1 mm thick MS sheet of same size and shape to almirah Medium steel. Complete all as directed and shown on drawing. (FD-1032/1034)

BED HARD WITH PLYTOP (FD/MAP/E6/08(R) - M & L 18mm thick Prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination of size 630x185mm, screwed to MS strip, arc welded to 18mm size rectangular pipe as in head board of Bed hard with plytop (Drg No FD/MAP/08(R)) including taking out old unserviceable head board complete all as specified and directed by Engineer-in-Charge.

M & L 18mm thick Prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination of size 630x310mm,, screwed to MS strip, arc welded to 18mm size rectangular pipe as in foot board of bed hard (Drg No FD/MAP/08(R)) including taking out old unserviceable foot board complete all as specified and directed by Engineer-in-Charge.

M & L 45x20x5mm size MS flat iron for fixing head/foot board, arc welded to rectangular pipe of bed hard,(Drg No FD/MAP/08(R)) apply two coats of synthetic enamel paint over a coat of red oxide primer to MS flat after welding including taking out old unserviceable MS strip of any size complete all as specified and directed by Engineer-in-Charge.

M & L 25x25x1.25mm thick MS square tube, 850mm long, as in stiffner of bed hard, welded to long rail (Drg No FD/MAP/08(R)), apply two coats of synthetic enamel paint over a coat of red oxide primer to MS pipe after welding including taking out old unserviceable MS pipe of any size complete all as specified and directed by Engineer-in-Charge.

M & L 12mm thick ply wood top BWR grade confirming to IS:303 as in bed hard (Drg No FD/MAP/08(R)),screwed to stiffner including taking out old unserviceable plywood complete all as specified and directed by Engineer-in-Charge. (Make: Kitply/ Century/Everest/Anchor)

S & F rubber shoes suitable for 38x38mm MS square tube as leg of bed hard (Drg No FD/MAP/08(R)) complete all as specified and directed by Engineer-in-Charge.

M & L preparation of old treated steel surfaces of Bed Hard MAP as per drawing and applying a coat of synthetic enamel black paint complete all as specified.

Charpoy IP with hard top (FD/MAP-II/01) :- M & L 45x20x5mm size MS flat iron for fixing head/foot board, arc welded to rectangular pipe of bed hard,(Drg No FD/MAP/08(R)) apply two coats of synthetic enamel paint over a coat of red oxide primer to MS flat after welding including taking out old unserviceable MS strip of any size complete all as specified and directed by Engineer-in-Charge.

M & L 25x25x1.25mm thick MS square tube, 850mm long, as in stiffner of bed hard, welded to long rail (Drg No FD/MAP/08(R)), apply two coats of synthetic enamel paint over a coat of red oxide primer to MS pipe after welding including taking out old unserviceable MS pipe of any size complete all as specified and directed by Engineer-in-Charge.

M & L 12mm thick ply wood top BWR grade confirming to IS:303 as in bed hard (Drg No FD/MAP/08(R)),screwed to stiffner including taking out old unserviceable plywood complete all as specified and directed by Engineer-in-Charge. (Make: Kitply/ Century/Everest/Anchor)

S & F rubber shoes suitable for 38x38mm MS square tube as leg of bed hard (Drg No FD/MAP/08(R)) complete all as specified and directed by Engineer-in-Charge.

M & L preparation of old treated steel surfaces of Charpoy as per drawing and applying a coat of synthetic enamel black paint complete all as specified.

BED HARD WITH PLYTOP (FD-246) - M&L for removing the old unserviceable/ broken leg from bed hard with plywood top and S&F new leg made out of 1st class teak wood and made to shape all as shown on drg and as directed by Engr-in-Charge (FD-246)

M & L for removing unserviceable/broken plywood from both side of head board of Bed plywood top and S & F new 4mm thick one side teak face plywood (Natural teak) to both side of head board including 6mm thick teak wood beading provided alround the head board and all as specified in drg and directed by Engr-in-Charge (FD-246)

All as per Sl item No. 95 here-in-above, but replacing foot board of Bed hard with plytop (FD - 246)

M & L for removing unserviceable long rail from Bed plywood top and S & F new long rail made out of 1st class teak wood and made to shape and all as specified in drg and directed by Engr-in-Charge (FD-246)

M & L for removing unserviceable short rail from Bed plywood top and S & F new short rail made out of 1st class teak wood and made to shape and all as specified in drg and directed by Engr-in-Charge (FD-246)

M & L for removing unserviceable centre supporitng stiffner from Bed plywood top and S & F new centre supporting stiffner made out of 1st class teak wood and made to shape and all as specified in drg and directed by Engr-in-Charge (FD-246)

M&L for removing unserviceable / wornout existing plywood from Bed plywood top and S & F new 12mm thick ply wood top BWR grade confirming to IS:303 of size 1950 x 900mm of approved make and fixing by SS screws and all as specified in drg and directed by Engr-in-Charge. (FD-246) (Make: Kitply/Century/Everest/ Anchor)

S & F triangular shape corner bracket size 70mm X 70mm long and 15mm thick made out of 1st class teak wood to be fixed to legs to long rail of Bed plywood and all as specified in drg and directed by Engr -in- Charge.(FD-246)

M & L preparation of old treated wooden surfaces of Bed hard with plytop and applying two coats of french polish complete all as specified and directed

Chair Verandah (FD/MAP-II/06):- M&L for replacing PVC seat & back 4mm th with weight not less than 1.85 kg. Complete all as directed and shown on drawing.

M & L preparation of old treated steel surfaces of Chair Varandah as per drawing No FD/MAP-II/06 and applying a coat of synthetic enamel white paint complete all as specified.

RACK SHOE STEEL,FD/E6/MAP/02(R) Removing the existing damaged/rusted legs (U shaped) carefully without damaging the other parts by using hand held cutting machine,Supply and fixing new legs (U shaped) made out 25mm dia MS pipe 18 gauge duly welded to its position.Complete all as directed and shown on drawing.

Removing the unserviceable wire mesh(Jali) shelves, Supply and fixing new wire mesh (Jali) shelves made out of 3mm dia MS rods duly welded to its position.Complete all as directed and shown on drawing.

S & F new PVC shoe suitable to the leg complete all as specified and shown on drawing.

M&L for painting shoe rack steel by peeling out the old paint by applying paint remover solution,filling metal putty to the uneven surfaces and sanding it to make the surface smooth then wipe out the surface and remove the dust with a fine cloth.Two coats of hammer tone paint as per existing shade shall be applied externally and internally to complete shoe rack.The painting to each article shall only be carried out by spray machine only.

TABLE BED SIDE, FD/MAP/15(R) :- M & L 18mm thick Prelaminated particle board, laminated one side with decorative choice lamination & other side balancing white lamination to match with existing colour & texture as in side/front/back/drawer of Table bedside with PVC edging (Drg No FD/MAP/15(R)) including taking out old unserviceable board complete all as specified and directed by Engineer-in-Charge.

S & F 50mm long, brass, chromium plated handle suitable for Table bed side complete all as specified.

M & L preparation of old treated steel surfaces of Table Bed side steel (MAP) and applying a coat of synthetic enamel paint complete all as specified.

CHAIR COMPUTER (FD/E6/MAP/01) :- Removing by unscrewing the unserviceable damaged Seat & back from each chair carefully .Removing the existing torn out tapsetry cloth ,pressed foam cushion,elastic webbing tape from each seat and back.The seat and back shall be fully upholstered by using new 60mm thick 40 density foam sheets and new webbing tape.The seat and back shall duly covered with new tapestry cloth of approved colour and texture ,the rate of cloth shall not be less than 350 per mtr.The fixing of cloth shall be done by using heavy duty gun tacker.Complete all as specified and as directed.

Removing old unserviceable arm rest of chair and S&F new arm of same shape and size ,made of black integral skin polyurethane with 75-85 shore 'Á ' hardness & reinforced with MS insert all as specified and directed by Engr -in -charge.

Removing unserviceable castor twin wheels and S&F new castor twin wheel suitable for chair computer all as directed Engr -in -charge.

Removing unserviceable adjustable pedestal assembly with hydraulic system and S&F new pedestal assembly with hydraulic system having forward tilt, self regulating tilt tension and manual override, 4 position tilt lock. Anti shock back mechanism to prevent backrest. 360 swivel mechanism to allow with fluid lateral movement suitable for chair computer all as specified and directed by Engr -in charge.

Painting to all steel portion of chair computer with one coat of synthetic enamel black paint after cleaning,dusting and scratching the entire metal surface of chair with sand paper ,making surface neat and smooth.

S&F table top with 18 mm thick pre laminated particle board of size 1200 x 600 mm with teak veneer facing on one side and balancing white lamination on the other side, including 4 mm thick teak wood edging alround the top and fixing the table top on top frame of Table office clerk steel (FD-84) with screws from bottom including taking down old table top complete. (Note:- All furniture repairs shall be carried out at BSO yard / various units as per direction of Engr in charge. Rates are inclusive of all subsequent expenditure occured on carrying out repair at various sites)

All as per Sl item No. 117 here-in-above, but new top of size 1800x1200 mm for Table office officer steel FD-84(M)

S&F lock for table drawer of Table office clerk steel FD - 84(M), MS lock, 4 lever with stainless steel duplicate keys, duly fixed to the top drawer and providing automatic locking system to other three drawers including taking down of old lock complete.

All as per Sl item No.119 here-in-above, but lock for Table office officer steel FD-84(M)

S&F new 1 mm MS channel runner of 400 mm long folded to make shape duly welded one side to table frame to run the drawers smoothly including taking down old broken channel and make functional all drawers of table office clerk steel FD - 84(M) complete.

All as per Sl item No.121 here-in-above, but MS channel runner for Table office officer steel FD-84(M)

M & L preparation of old treated steel surfaces as per drawing No. FD-84 and applying a coat of synthetic enamel paint colour as directed by Engineer-in-Charge.

Removal of old broken wooden seat/ Wooden Back of Chair CBA/ CB steel and replacing with new II class hardwood seat of size 460x380 mm duly canned with godrej pattern and teakwood shade polish shall be fixed with MS screws to frame of Chair CBA/ CB steel all as specified and directed.(FD-75(M)

Removal of old broken wooden Arm rest of Chair CBA with arms and replacing with new II class hardwood arm rest with teakwood shade polish shall be fixed with MS screws to frame of Chair CBA with arms all as specified and directed.(FD-75(M)

M & L for preparation of old treated steel surfaces of Chair CBA/ CB steel and applying two coat of synthetic enamel paint colour as specified by Engr-In-charge. FD-75(M)

M & L for canning of Chair Dining / chair verandah / Chair Easy / Chair Writing / Chair CBA steel / Chair CB steel with new plastic cane of size 3.0mm x 0.60mm cane including taking out old/damaged plastic cane and cleaning the entire surface complete all as specified and directed.

CHAIR REVOLVING MAKE-ADIKO / GODREJ, MODEL NO - LEATHERITE CHAIR / ACE :- Removing by unscrewing the unserviceable damaged Seat & back from each chair carefully .Removing the existing torn out tapsetry cloth, pressed foam cushion,elastic webbing tape from each seat and back.The seat and back shall be fully upholstered by using new 60mm thick 40 density foam sheets and new webbing tape.The seat and back shall duly covered with new leatherite of approved colour and texture.Complete all as specified and as directed.

Removing old unserviceable arm rest of chair and S&F new arm of same shape and size all as specified and directed by Engr -in -charge.

Removing unserviceable castor twin wheels and S&F new castor twin wheel suitable for chair .Complete all as directed and shown on drawing.

Removing old unserviceable Hydraulic cylinder of chair and S&F new hydraulic cylinder all as specified and directed by Engr -in -charge.

Removing unserviceable pedestal assembly,supply and fixing new pedestal assembly having five arms with twin wheel castor wheels having wheel base not less than 70 cms.Complete all as directed and shown on drawing.

Gun Painting to all steel portion of chair revolving with synthetic enamel black paint after cleaning,dusting and scratching the entire metal surface of chair with sand paper, making surface neat and smooth.Complete all as directed and shown on drawing.

GODREJ INTERIO CIGNUS MAIN TABLE / GODREJ INTERIO FINNESSE MAIN TABLE :- S&F new set of 1 mm MS channel runner of 400 mm long folded to make shape duly welded one side to table frame to run the drawers smoothly including taking down old broken channel and make functional all drawers of GODREJ INTERIO TABLE

Mahesh Traders

Chitturi Associates

ANJALI CONSTRUCTIONS