Fixing of rate contract for repairs to HT Distribution Transformers and AVRs installed at different WSSs of PHE Mechanical Sub-Division Baramulla, Sopore and Handwara (District Baramulla, Bandipore and Kupwara) for one financial year i.e., 2022-23.

Repairs to 25KVA HT transformers including following series of works

Disconnecting from active HT circuit, transportation of damaged transformers from water supply scheme to contractors workshop, loading / unloading of damaged transformers at respective locations, arranging for inspections, opening bolt-nuts of top cover, opening of the top plate, assessment of repairs, disconnecting of leads/connections, cleaning all healthy parts, removal of core yoke and windings and re-assembling of the dismantled materials and metal parts and positioning the core back after repairs, winding and complete electrical connections, bolting up top cover after filtration and top up/filling up of transformer oil and other fittings on cover or tank. Testing on load and full load at testing bay of workshop, loading of repaired transformer from workshop, transportation and unloading at installation site, connecting to HT circuit, testing on no load and then on full load

Providing / Fitting of HV winding (Aluminum)

Providing / Fitting of LV Winding (Aluminum)

Providing / Fitting of HV Porcelain bushings

Providing / Fitting of HV terminal Bolt with 4 nuts and washer

Providing / Fitting of LV Bushing

Providing / Fitting of LV terminal Bolt with 4 nuts and washer

Providing / Fitting of Top cover gasket and gaskets of oil gauge, breather cap, oil cap etc.

Providing / Fitting of HV/LV rod gaskets eg. flat gasket, D bush, cone bush

Providing / Fitting of Breather with Silica Gel

Providing / Fitting of Drain Valve with Filter Valve with Plug

Providing / Fitting of CRGO Lamination of grade M4 or M3

Providing / Fitting of Explosion vent

Providing / Fitting of Gun metal valves

Providing / Fitting of Core Bolt with insulation

Providing / Fitting of Insulating materials such as Press Board, Cotton Tape, Kraft Paper

Providing / applying of Paint of Tank as per IEE rules

Providing / Fitting of MS bolts and Nuts, washers, spring washers of different size

Providing / Fitting of Connection Wire (copper)

Providing / Fitting of Soldering Lead + Flux + Brazing Rod

Providing / Fitting of SRBP Tube

Providing / Fitting of Lid bolts

Providing / filling of Insulating media (Toil) of 11 KVA grade dielectric strength of 5 KV at 4mm air gap

Welding of tank and other parts at the point of leakages near leaking bushes

Cost on account of Drying of active parts by opening for 48 to 72 hours at heated primesis for removal of moisture of the repaired Transformer

Cost on account of Oil filtering to remove carbon content and other desired impurities

Cost of scrap windings (aluminum)

Bush rod clamp (aluminum)

Damaged brass parts

Released scrap Iron /MS

Damaged lamination

Repairs to 63KVA HT transformers including following series of works

Disconnecting from active HT circuit, transportation of damaged transformers from water supply scheme to contractors workshop, loading / unloading of damaged transformers at respective locations, arranging for inspections, opening bolt-nuts of top cover, opening of the top plate, assessment of repairs, disconnecting of leads/connections, cleaning all healthy parts, removal of core yoke and windings and re-assembling of the dismantled materials and metal parts and positioning the core back after repairs, winding and complete electrical connections, bolting up top cover after filtration and top up/filling up of transformer oil and other fittings on cover or tank. Testing on load and full load at testing bay of workshop, loading of repaired transformer from workshop, transportation and unloading at installation site, connecting to HT circuit, testing on no load and then on full load

Providing / Fitting of HV winding (Aluminum)

Providing / Fitting of LV Winding (Aluminum)

Providing / Fitting of HV Porcelain bushings

Providing / Fitting of HV terminal Bolt with 4 nuts and washer

Providing / Fitting of LV Bushing

Providing / Fitting of LV terminal Bolt with 4 nuts and washer

Providing / Fitting of Top cover gasket and gaskets of oil gauge, breather cap, oil cap etc.

Providing / Fitting of HV/LV rod gaskets eg. flat gasket, D bush, cone bush

Providing / Fitting of Breather with Silica Gel

Providing / Fitting of Drain Valve with Filter Valve with Plug

Providing / Fitting of CRGO Lamination of grade M4 or M3

Providing / Fitting of Explosion vent

Providing / Fitting of Gun metal valves

Providing / Fitting of Core Bolt with insulation

Providing / Fitting of Insulating materials such as Press Board, Cotton Tape, Kraft Paper

Providing / applying of Paint of Tank as per IEE rules

Providing / Fitting of MS bolts and Nuts, washers, spring washers of different size

Providing / Fitting of Connection Wire (copper)

Providing / Fitting of Soldering Lead + Flux + Brazing Rod

Providing / Fitting of SRBP Tube

Providing / Fitting of Lid bolts

Providing / filling of Insulating media (Toil) of 11 KVA grade dielectric strength of 5 KV at 4mm air gap

Welding of tank and other parts at the point of leakages near leaking bushes

Cost on account of Drying of active parts by opening for 48 to 72 hours at heated primesis for removal of moisture of the repaired Transformer

Cost on account of Oil filtering to remove carbon content and other desired impurities

Cost of scrap windings (aluminum)

Damaged brass parts

Bush rod clamp (aluminum)

Released scrap Iron /MS

Damaged lamination

Repairs to 100KVA HT transformers including following series of works

Disconnecting from active HT circuit, transportation of damaged transformers from water supply scheme to contractors workshop, loading / unloading of damaged transformers at respective locations, arranging for inspections, opening bolt-nuts of top cover, opening of the top plate, assessment of repairs, disconnecting of leads/connections, cleaning all healthy parts, removal of core yoke and windings and re-assembling of the dismantled materials and metal parts and positioning the core back after repairs, winding and complete electrical connections, bolting up top cover after filtration and top up/filling up of transformer oil and other fittings on cover or tank. Testing on load and full load at testing bay of workshop, loading of repaired transformer from workshop, transportation and unloading at installation site, connecting to HT circuit, testing on no load and then on full load

Providing / Fitting of HV winding (Aluminum)

Providing / Fitting of LV Winding (Aluminum)

Providing / Fitting of HV Porcelain bushings

Providing / Fitting of HV terminal Bolt with 4 nuts and washer

Providing / Fitting of LV Bushing

Providing / Fitting of LV terminal Bolt with 4 nuts and washer

Providing / Fitting of Top cover gasket and gaskets of oil gauge, breather cap, oil cap etc.

Providing / Fitting of HV/LV rod gaskets eg. flat gasket, D bush, cone bush

Providing / Fitting of Breather with Silica Gel

Providing / Fitting of Drain Valve with Filter Valve with Plug

Providing / Fitting of CRGO Lamination of grade M4 or M3

Providing / Fitting of Explosion vent

Providing / Fitting of Gun metal valves

Providing / Fitting of Core Bolt with insulation

Providing / Fitting of Insulating materials such as Press Board, Cotton Tape, Kraft Paper

Providing / applying of Paint of Tank as per IEE rules

Providing / Fitting of MS bolts and Nuts, washers, spring washers of different size

Providing / Fitting of Connection Wire (copper)

Providing / Fitting of Soldering Lead + Flux + Brazing Rod

Providing / Fitting of SRBP Tube

Providing / Fitting of Lid bolts

Providing / filling of Insulating media (Toil) of 11 KVA grade dielectric strength of 5 KV at 4mm air gap

Welding of tank and other parts at the point of leakages near leaking bushes

Cost on account of Drying of active parts by opening for 48 to 72 hours at heated primesis for removal of moisture of the repaired Transformer

Cost on account of Oil filtering to remove carbon content and other desired impurities

Cost of scrap windings (aluminum)

Damaged brass parts

Bush rod clamp (aluminum)

Released scrap Iron /MS

Damaged lamination

Repairs to 200KVA (Aluminium wound) HT transformers including following series of works

Disconnecting from active HT circuit, transportation of damaged transformers from water supply scheme to contractors workshop, loading / unloading of damaged transformers at respective locations, arranging for inspections, opening bolt-nuts of top cover, opening of the top plate, assessment of repairs, disconnecting of leads/connections, cleaning all healthy parts, removal of core yoke and windings and re-assembling of the dismantled materials and metal parts and positioning the core back after repairs, winding and complete electrical connections, bolting up top cover after filtration and top up/filling up of transformer oil and other fittings on cover or tank. Testing on load and full load at testing bay of workshop, loading of repaired transformer from workshop, transportation and unloading at installation site, connecting to HT circuit, testing on no load and then on full load

Providing / Fitting of HV winding (Aluminum)

Providing / Fitting of LV Winding (Aluminum)

Providing / Fitting of HV Porcelain bushings

Providing / Fitting of HV terminal Bolt with 4 nuts and washer

Providing / Fitting of LV Bushing

Providing / Fitting of LV terminal Bolt with 4 nuts and washer

Providing / Fitting of Top cover gasket and gaskets of oil gauge, breather cap, oil cap etc.

Providing / Fitting of HV/LV rod gaskets eg. flat gasket, D bush, cone bush

Providing / Fitting of Breather with Silica Gel

Providing / Fitting of Drain Valve with Filter Valve with Plug

Providing / Fitting of CRGO Lamination of grade M4 or M3

Providing / Fitting of Explosion vent

Providing / Fitting of Gun metal valves

Providing / Fitting of Core Bolt with insulation

Providing / Fitting of Insulating materials such as Press Board, Cotton Tape, Kraft Paper

Providing / applying of Paint of Tank as per IEE rules

Providing / Fitting of MS bolts and Nuts, washers, spring washers of different size

Providing / Fitting of Connection Wire (copper)

Providing / Fitting of Soldering Lead + Flux + Brazing Rod

Providing / Fitting of SRBP Tube

Providing / Fitting of Lid bolts

Providing / filling of Insulating media (Toil) of 11 KVA grade dielectric strength of 5 KV at 4mm air gap

Welding of tank and other parts at the point of leakages near leaking bushes

Cost on account of Drying of active parts by opening for 48 to 72 hours at heated primesis for removal of moisture of the repaired Transformer

Cost on account of Oil filtering to remove carbon content and other desired impurities

Cost of scrap windings (aluminum)

Damaged brass parts

Bush rod clamp (aluminum)

Released scrap Iron /MS

Damaged lamination

Repairs to 250KVA (Aluminium wound) HT transformers including following series of works

Disconnecting from active HT circuit, transportation of damaged transformers from water supply scheme to contractors workshop, loading / unloading of damaged transformers at respective locations, arranging for inspections, opening bolt-nuts of top cover, opening of the top plate, assessment of repairs, disconnecting of leads/connections, cleaning all healthy parts, removal of core yoke and windings and re-assembling of the dismantled materials and metal parts and positioning the core back after repairs, winding and complete electrical connections, bolting up top cover after filtration and top up/filling up of transformer oil and other fittings on cover or tank. Testing on load and full load at testing bay of workshop, loading of repaired transformer from workshop, transportation and unloading at installation site, connecting to HT circuit, testing on no load and then on full load

Providing / Fitting of HV winding (Aluminum)

Providing / Fitting of LV Winding (Aluminum)

Providing / Fitting of HV Porcelain bushings

Providing / Fitting of HV terminal Bolt with 4 nuts and washer

Providing / Fitting of LV Bushing

Providing / Fitting of LV terminal Bolt with 4 nuts and washer

Providing / Fitting of Top cover gasket and gaskets of oil gauge, breather cap, oil cap etc.

Providing / Fitting of HV/LV rod gaskets eg. flat gasket, D bush, cone bush

Providing / Fitting of Breather with Silica Gel

Providing / Fitting of Drain Valve with Filter Valve with Plug

Providing / Fitting of CRGO Lamination of grade M4 or M3

Providing / Fitting of Explosion vent

Providing / Fitting of Gun metal valves

Providing / Fitting of Core Bolt with insulation

Providing / Fitting of Insulating materials such as Press Board, Cotton Tape, Kraft Paper

Providing / applying of Paint of Tank as per IEE rules

Providing / Fitting of MS bolts and Nuts, washers, spring washers of different size

Providing / Fitting of Connection Wire (copper)

Providing / Fitting of Soldering Lead + Flux + Brazing Rod

Providing / Fitting of SRBP Tube

Providing / Fitting of Lid bolts

Providing / filling of Insulating media (Toil) of 11 KVA grade dielectric strength of 5 KV at 4mm air gap

Welding of tank and other parts at the point of leakages near leaking bushes

Cost on account of Drying of active parts by opening for 48 to 72 hours at heated primesis for removal of moisture of the repaired Transformer

Cost on account of Oil filtering to remove carbon content and other desired impurities

Cost of scrap windings (aluminum)

Damaged brass parts

Bush rod clamp (aluminum)

Released scrap Iron /MS

Damaged lamination

Repairs to 250KVA (Copper Wound) HT transformers including following series of works

Disconnecting from active HT circuit, transportation of damaged transformers from water supply scheme to contractors workshop, loading / unloading of damaged transformers at respective locations, arranging for inspections, opening bolt-nuts of top cover, opening of the top plate, assessment of repairs, disconnecting of leads/connections, cleaning all healthy parts, removal of core yoke and windings and re-assembling of the dismantled materials and metal parts and positioning the core back after repairs, winding and complete electrical connections, bolting up top cover after filtration and top up/filling up of transformer oil and other fittings on cover or tank. Testing on load and full load at testing bay of workshop, loading of repaired transformer from workshop, transportation and unloading at installation site, connecting to HT circuit, testing on no load and then on full load

Providing / Fitting of HV winding Copper)

Providing / Fitting of LV Winding (Copper)

Providing / Fitting of HV Porcelain bushings

Providing / Fitting of HV terminal Bolt with 4 nuts and washer

Providing / Fitting of LV Bushing

Providing / Fitting of LV terminal Bolt with 4 nuts and washer

Providing / Fitting of Top cover gasket and gaskets of oil gauge, breather cap, oil cap etc.

Providing / Fitting of HV/LV rod gaskets eg. flat gasket, D bush, cone bush

Providing / Fitting of Breather with Silica Gel

Providing / Fitting of Drain Valve with Filter Valve with Plug

Providing / Fitting of CRGO Lamination of grade M4 or M3

Providing / Fitting of Explosion vent

Providing / Fitting of Gun metal valves

Providing / Fitting of Core Bolt with insulation

Providing / Fitting of Insulating materials such as Press Board, Cotton Tape, Kraft Paper

Providing / applying of Paint of Tank as per IEE rules

Providing / Fitting of MS bolts and Nuts, washers, spring washers of different size

Providing / Fitting of Connection Wire (copper)

Providing / Fitting of Soldering Lead + Flux + Brazing Rod

Providing / Fitting of SRBP Tube

Providing / Fitting of Lid bolts

Providing / filling of Insulating media (Toil) of 11 KVA grade dielectric strength of 5 KV at 4mm air gap

Welding of tank and other parts at the point of leakages near leaking bushes

Cost on account of Drying of active parts by opening for 48 to 72 hours at heated primesis for removal of moisture of the repaired Transformer

Cost on account of Oil filtering to remove carbon content and other desired impurities

Cost of scrap windings (Copper)

Damaged brass parts

Bush rod clamp (Copper)

Released scrap Iron /MS

Damaged lamination

Repairs to 400KVA HT transformers including following series of works

Disconnecting from active HT circuit, transportation of damaged transformers from water supply scheme to contractors workshop, loading / unloading of damaged transformers at respective locations, arranging for inspections, opening bolt-nuts of top cover, opening of the top plate, assessment of repairs, disconnecting of leads/connections, cleaning all healthy parts, removal of core yoke and windings and re-assembling of the dismantled materials and metal parts and positioning the core back after repairs, winding and complete electrical connections, bolting up top cover after filtration and top up/filling up of transformer oil and other fittings on cover or tank. Testing on load and full load at testing bay of workshop, loading of repaired transformer from workshop, transportation and unloading at installation site, connecting to HT circuit, testing on no load and then on full load

Providing / Fitting of HV winding (Copper)

Providing / Fitting of LV Winding (Copper)

Providing / Fitting of HV Porcelain bushings

Providing / Fitting of HV terminal Bolt with 4 nuts and washer

Providing / Fitting of LV Bushing

Providing / Fitting of LV terminal Bolt with 4 nuts and washer

Providing / Fitting of Top cover gasket and gaskets of oil gauge, breather cap, oil cap etc.

Providing / Fitting of HV/LV rod gaskets eg. flat gasket, D bush, cone bush

Providing / Fitting of Breather with Silica Gel

Providing / Fitting of Drain Valve with Filter Valve with Plug

Providing / Fitting of CRGO Lamination of grade M4 or M3

Providing / Fitting of Explosion vent

Providing / Fitting of Gun metal valves

Providing / Fitting of Core Bolt with insulation

Providing / Fitting of Insulating materials such as Press Board, Cotton Tape, Kraft Paper

Providing / applying of Paint of Tank as per IEE rules

Providing / Fitting of MS bolts and Nuts, washers, spring washers of different size

Providing / Fitting of Connection Wire (copper)

Providing / Fitting of Soldering Lead + Flux + Brazing Rod

Providing / Fitting of SRBP Tube

Providing / Fitting of Lid bolts

Providing / filling of Insulating media (Toil) of 11 KVA grade dielectric strength of 5 KV at 4mm air gap

Welding of tank and other parts at the point of leakages near leaking bushes

Cost on account of Drying of active parts by opening for 48 to 72 hours at heated primesis for removal of moisture of the repaired Transformer

Cost on account of Oil filtering to remove carbon content and other desired impurities

Cost of scrap windings (Copper)

Damaged brass parts

Bush rod clamp (Copper)

Released scrap Iron /MS

Damaged lamination

Repairs to 630KVA HT transformers including following series of works

Disconnecting from active HT circuit, transportation of damaged transformers from water supply scheme to contractors workshop, loading / unloading of damaged transformers at respective locations, arranging for inspections, opening bolt-nuts of top cover, opening of the top plate, assessment of repairs, disconnecting of leads/connections, cleaning all healthy parts, removal of core yoke and windings and re-assembling of the dismantled materials and metal parts and positioning the core back after repairs, winding and complete electrical connections, bolting up top cover after filtration and top up/filling up of transformer oil and other fittings on cover or tank. Testing on load and full load at testing bay of workshop, loading of repaired transformer from workshop, transportation and unloading at installation site, connecting to HT circuit, testing on no load and then on full load

Providing / Fitting of HV winding (Copper)

Providing / Fitting of LV Winding (Copper)

Providing / Fitting of HV Porcelain bushings

Providing / Fitting of HV terminal Bolt with 4 nuts and washer

Providing / Fitting of LV Bushing

Providing / Fitting of LV terminal Bolt with 4 nuts and washer

Providing / Fitting of Top cover gasket and gaskets of oil gauge, breather cap, oil cap etc.

Providing / Fitting of HV/LV rod gaskets eg. flat gasket, D bush, cone bush

Providing / Fitting of Breather with Silica Gel

Providing / Fitting of Drain Valve with Filter Valve with Plug

Providing / Fitting of CRGO Lamination of grade M4 or M3

Providing / Fitting of Explosion vent

Providing / Fitting of Gun metal valves

Providing / Fitting of Core Bolt with insulation

Providing / Fitting of Insulating materials such as Press Board, Cotton Tape, Kraft Paper

Providing / applying of Paint of Tank as per IEE rules

Providing / Fitting of MS bolts and Nuts, washers, spring washers of different size

Providing / Fitting of Connection Wire (copper)

Providing / Fitting of Soldering Lead + Flux + Brazing Rod

Providing / Fitting of SRBP Tube

Providing / Fitting of Lid bolts

Providing / filling of Insulating media (Toil) of 11 KVA grade dielectric strength of 5 KV at 4mm air gap

Welding of tank and other parts at the point of leakages near leaking bushes

Cost on account of Drying of active parts by opening for 48 to 72 hours at heated primesis for removal of moisture of the repaired Transformer

Cost on account of Oil filtering to remove carbon content and other desired impurities

Cost of scrap windings (Copper)

Damaged brass parts

Bush rod clamp (Copper)

Released scrap Iron /MS

Damaged lamination

Repairs to 100KVA AVR (Buck Boost Type) including following series of works

Disconnecting from active HT circuit Transportation of damaged Buck Boost Transformer with or without regulator from water supply scheme to contractors workshop, loading / unloading at respective locations, arranging for Inspections, opening bolt-nuts of top cover, opening of the top plate ,assessment of repairs, disconnecting of leads/connections, cleaning all healthy parts, removal of core yoke and windings, and reassembly of the dismantled materials & metal parts and positioning the core back after repairs, winding and complete electrical connections, bolting up top cover after filtration & top up/filling up of transformer oil and, other fittings on cover or tank, testing on load and full load at testing bay of workshop, Loading of repaired equipment from workshop ,transportation and unloading at installation site , connecting to HT circuit , testing on no load and then on full load

Providing / Fitting of winding (Copper wire) for Buck Boost Transformer

Providing / Fitting of LV Winding (Copper strip) for regulator part

Providing / Fitting of HV Porcelain bushings

Providing / Fitting of HV terminal Bolt with 4 nuts and washer

Providing / Fitting of LV Bushing for both parts

Providing / Fitting of LV terminal Bolt with 4 nuts and washer for both parts

Providing / Fitting of Top cover gasket and gaskets of oil gauge, breather cap, vent cap etc.

Providing / Fitting of HV/LV rod gaskets eg: flat gasket, D bush, cone bush

Providing / Fitting of Breather with Silica Gel

Providing / Fitting of Drain Valves with Filter Valve with Plug

Providing / Fitting of CRGO Lamination of grade M4 or M3

Providing / Fitting of Air release plug

Providing / Fitting of thermometer pocket

Providing / Fitting of Gun metal valves including filter valve

Providing / Fitting of Core Bolt with insulation

Providing / Fitting of Insulating materials such as Press Board, Cotton Tape, Kraft Paper

Providing / applying of Paint of Tanks as per IEE rules

Providing / Fitting of MS bolts and Nuts, washers, spring washers of different size

Providing / Fitting of Connection Wire (copper)

Providing / Fitting of Soldering Lead + Flux + Brazing Rod

Providing / Fitting of SRBP Tube

Providing / Fitting of Lid bolts

Providing / Fitting of voltage control cads for regulating panel with their collaboration

Providing / Fitting of Toggle switches for circuit changing in regulating panel

Providing / Fitting of indicating lamps for regulating panel

Providing / Fitting of DC coils for the regulating panel

Providing / filling of Insulating media (Toil) of 11 KVA grade dielectric strength of 5 KV at 4mm air gap

Welding of tank and other parts at the point of leakages near leaking bushes

Cost on account of Drying of active parts by opening for 48 to 72 hours at heated premises for removal of moisture of the repaired Transformer

Cost on account of Oil filtering to remove carbon content and other desired impurities

Cost of scrap windings (copper) for Buck Boost Transformer

Cost of scrap windings (Copper strip) for regulator part

Released scrap Iron / MS

Damaged lamination

Repairs to 400KVA AVR (Buck Boost Type) including following series of works

Disconnecting from active HT circuit Transportation of damaged Buck Boost Transformer with or without regulator from water supply scheme to contractors workshop, loading / unloading at respective locations, arranging for Inspections, opening bolt-nuts of top cover, opening of the top plate ,assessment of repairs, disconnecting of leads/connections, cleaning all healthy parts, removal of core yoke and windings, and reassembly of the dismantled materials & metal parts and positioning the core back after repairs, winding and complete electrical connections, bolting up top cover after filtration & top up/filling up of transformer oil and, other fittings on cover or tank, testing on load and full load at testing bay of workshop, Loading of repaired equipment from workshop ,transportation and unloading at installation site , connecting to HT circuit , testing on no load and then on full load

Providing / Fitting of winding (Copper wire) for Buck Boost Transformer

Providing / Fitting of LV Winding (Copper strip) for regulator part

Providing / Fitting of HV Porcelain bushings

Providing / Fitting of HV terminal Bolt with 4 nuts and washer

Providing / Fitting of LV Bushing for both parts

Providing / Fitting of LV terminal Bolt with 4 nuts and washer for both parts

Providing / Fitting of Top cover gasket and gaskets of oil gauge, breather cap, vent cap etc.

Providing / Fitting of HV/LV rod gaskets eg: flat gasket, D bush, cone bush

Providing / Fitting of Breather with Silica Gel

Providing / Fitting of Drain Valves with Filter Valve with Plug

Providing / Fitting of CRGO Lamination of grade M4 or M3

Providing / Fitting of Air release plug

Providing / Fitting of thermometer pocket

Providing / Fitting of Gun metal valves including filter valve

Providing / Fitting of Core Bolt with insulation

Providing / Fitting of Insulating materials such as Press Board, Cotton Tape, Kraft Paper

Providing / applying of Paint of Tanks as per IEE rules

Providing / Fitting of MS bolts and Nuts, washers, spring washers of different size

Providing / Fitting of Connection Wire (copper)

Providing / Fitting of Soldering Lead + Flux + Brazing Rod

Providing / Fitting of SRBP Tube

Providing / Fitting of Lid bolts

Providing / Fitting of voltage control cads for regulating panel with their collaboration

Providing / Fitting of Toggle switches for circuit changing in regulating panel

Providing / Fitting of indicating lamps for regulating panel

Providing / Fitting of DC coils for the regulating panel

Providing / filling of Insulating media (Toil) of 11 KVA grade dielectric strength of 5 KV at 4mm air gap

Welding of tank and other parts at the point of leakages near leaking bushes

Cost on account of Drying of active parts by opening for 48 to 72 hours at heated premises for removal of moisture of the repaired Transformer

Cost on account of Oil filtering to remove carbon content and other desired impurities

Cost of scrap windings (copper) for Buck Boost Transformer

Cost of scrap windings (Copper strip) for regulator part

Released scrap Iron / MS

Damaged lamination

M/S JAY DEE ENTERPRISES

M/S FANCY ELECTRIC AND STEEL FABRICATORS

Asif Engineering Works

M/S JAY DEE ENTERPRISES