Providing RCC Drain in Koramenugunta up to existing pipe culvert in ward no.2 of Tirupati Urban Mandal

Bailing out water from the water logged areas with oil engine driven pumpsets, including hire charges fuel charges and wages for Driver and Helper etc., complete

Earthwork excavation in soils upto SDR by mechanical means for foundations of structures as per drawing and technical specification including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing sides of bottom, back filling the excavation earth to the extent required etc., complete for finished item of work, excluding seigniorage charges, as per MoRT&H specification 304 (5th Revision) and as directed by the Engineer-in-Charge

Sand filling in foundation including cost and conveyence of all materials to site and watering, tamping etc., complete for finshed item of work as per MoRT&H specification 304 (5th Revision) and as directed by the Engineer - in - Charge.

Providing Cement Concrete (1:4:8) mix using 40mm size HBG crushed stone aggregate and fine aggregate conforming to table 1000-2 of MoRT&H including cost, conveyance of all materials to site and labour charges, centering, machine mixing, laying, Vibrating, curing etc., including all other incidental and operational charges of all T&P etc., complete for finished item of work as per MoRT&H specification 1500,1700, 2100 (5th Revision) and as directed by the Engineer-in-Charge for base coarse below CC Pavement

Supply and placing of M 25 DESIGN MIX CONCRETE corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cum (707 kgs),. 10 mm HBG crushed metal, 0.362 cum (471 kgs), Sand 0.450 cum (616 kgs.) and cement 403 kgs with water cement ratio of 0.48 (182.40 ltrs/ cum of CC)etc., to site and including all operational, incidental and labour charges such as machine mixing, vibrating, dewatering, laying concrete, curing etc., complete with cement from standard suppliers approved by the department etc., complete and excluding cost of steel and its fabrication charges for finished item of work RCC Grade M25 (design Mix) using 20mm graded metal (MoRD & MoRTH 12.8E)

Supply and placing of M 25 DESIGN MIX CONCRETE corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cum (707 kgs),. 10 mm HBG crushed metal, 0.362 cum (471 kgs), Sand 0.450 cum (616 kgs.) and cement 403 kgs with water cement ratio of 0.48 (182.40 ltrs/ cum of CC)etc., to site and including all operational, incidental and labour charges such as machine mixing, vibrating, dewatering, laying concrete, curing etc., complete with cement from standard suppliers approved by the department etc., complete and excluding cost of steel and its fabrication charges for finished item of work RCC Grade M25 (design Mix) using 20mm graded metal (MoRD & MoRTH 12.8E)

Hire charges for centering for RCC vertical walls using Steel scaffolding pipes, jack props, wallers, foot plates, brackets, steel centering plates etc., including retaining of water for curing and removing of centering etc., complete as directed during execution complete

Filling with useful available excavated earth (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T&P etc., complete for finished item of work.

Carting of unserviceable soils loading and disposal upto 1000 mts etc., complete for finished item of work as directed by the Engineer-in-Charge

Providing HYSD bars ( Fe-500 ) of different diameters, wrought and put up bars of all diameters including cost and conveyance of steel to site and all labour charges for fabrication of reinforcement including cutting, bending, binding rods, tying grills, placing them in position etc., complete including cost and conveyance of binding wire and all handling charges and operational charges etc., and including over lapping welding if required etc., complete for all R.C.C items for finished item of work as per standard drawings, as per the directions of the Engineer-in-Charge and as per MoRT&H specification 1600 & 2100 (5th revision) and as per I.S.1786 of 1985 for Foundations of RCC Items