Loading
Loading…
Loading…
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Tender Value
₹1.1 Cr
EMD Value
₹2.2 L
Closing Date
5 Nov 2026, 3:00 pm
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
WORKS
15 conditions · 3 needing a document upload
The tenderer must have minimum average annual contractual turnoverofV/N or 'V' whichever is less; where V= Advertised value of the tenderincrores of Rupees N= Number of years prescribed for completion ofworkfor which bids have been invited. The average annualcontractualturnover shall be calculated as an average of "totalcontractualpayments" in the previous three financial years, as per theauditedbalance sheet. However, in case balance sheet of the previousyear isyet to be prepared/ audited, the audited balance sheet of thefourthprevious year shall be considered for calculating averageannualcontractual turnover. The tenderers shall submit requisiteinformation asper Annexure-VIB, along with copies of Audited BalanceSheets duly certified by the Chartered Accountant/ Certificate fromChartered Accountant duly supported by Audited Balance Sheet
a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s)during last 07(seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40%of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b) (1)Incase of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s)during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii)One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note forb(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents byway of Special Conditions, a formal agreement duly not arised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway.
Note for Technical Eligibility Criteria: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/ registered at least 5years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate
Definition of Single Similar Work: For the purpose of this work, SingleSimilar work shall be taken as "Any signal interlocking works 1.1.1 involving Elor RRI or PI or IBS or IBH or LC gate or yard modification or UFSBI or Trackcircuit (AFTC or DC TC) or Axle Counter (SSDAC or MSDAC or HASSDAC)orAutomatic signalling"
27 conditions · 3 needing a document upload
All the tenderers/Contractors have to deposit full Bid Security and tender document cost as stipulated for the tender, through online modes as permitted in IREPS application through multiple banks net banking, debit and credit cards . All documents related to Partnership deed/Joint venture/ Consortium/ MOU, duly signed by the notary public, should be uploaded failing which offer will be summarily rejected.
Until a formal agreement is prepared and executed, acceptance of this tender shall constitute a binding contract between us subject to modifications, as may be mutually agreed to between us and indicated in the letter of acceptance of my/our offer for this work.
I/We also hereby agree to abide by the Indian Railways Standard General Conditions Of Contract for works 2022, with all correction slips up-to-date and to carry out the work according to the Special Conditions of Contract and Specifications of materials and works as laid down by Railway in the annexed Special Conditions/Specifications, Schedule of Rates with all correction slips up to date for the present contract
I/We offer to do the work for DRM/S&T/TVC, at the rates quoted in the attached schedule and hereby bind myself/ourselves to complete the work in all respects within the period of completion stipulated in the tender document, from the date of issue of letter of acceptance of the tender. The amount as stipulated in the tender document is herewith forwarded as Bid Security. Full value of the bid security shall stand forfeited without prejudice to any other right or remedies in case my/our Tender is accepted and if : (a) I/We do not execute the contract documents as stipulated in performance guarantee clause of GCC for works 2022 as detailed in general instructions. (b) I/We do not commence the work within seven days after receipt of orders to that effect.
I/We hereby Confirm that the rates, rebates and/or other financial terms, if any, quoted by us in the relevant fields of the Financial Bid page will only be the ruling terms for deciding the inter-se ranking, and any such condition having financial repercussions, if quoted by us anywhere else including attached documents shall not be considered for deciding inter-se ranking
However, Railways shall have the right to incorporate any such condition quoted by us, in the contract, at their discretion, if contract is placed on us.
Manual submission of Bid Security and cost of tender form cannot be entertained/Considered and hence no need of uploading the scanned copy of financial instruments
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The tenderer whether sole proprietor / a company or a partnership firm / joint venture (JV) / registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association Board resolution, failing which tender shall be summarily rejected. The tenderer whether sole proprietor / a company or a partnership firm / joint venture (JV) / registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association Board resolution, failing which tender shall be summarily rejected. A separate power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, shall be submitted after award of work, specifically authorizing him/them to deal with all other contractual activities subsequent to signing of agreement, if required. Note: A Power of Attorney executed and issued overseas, the document will also have to be legalized by the Indian Embassy and notarized in the jurisdiction where the Power of Attorney is being issued. However, the Power of Attorney provided by Bidders from countries that have signed the Hague Legislation Convention 1961 are not required to be legalized by the Indian Embassy if it carries a conforming Appostille certificate.
INSTRUCTIONS TO TENDERERS
The tenderer shall thoroughly go through the entire tender documents and strictly adhere the instructions and directions given at different pages.
Tender Document Cost for this work is Nil.
Unreleased Bid Security, if any, held with the Railway Administration, shall not be adjusted towards the Bid security to be remitted.
If the Tenderer(s) deliberately give(s) wrong information/ incorrect documents in his/their tender or create circumstances for the acceptance of his/their tender, the Railway reserves the right to reject such tender at any stage. The entire Bid Security and any other dues available with Railway against that contract will be forfeited. Action will be taken to suspend the business with the tenderer for a period of two years. In addition, Administration reserves the right to prosecute under suitable law.
All terms and conditions in the tender documents are binding on the Tenderers.
Railways reserves the right to accept or reject any or all the tenders and to award the work in whole or in part without assigning the reason for any such action.
The Tenderers are advised to visit the site of work in their own interest and acquaint themselves with the site conditions and expected quantum of work and assess all the site specific difficulties to be experienced while executing the same and the rate shall be arrived duly considering all the facts above and quoted in the tender. Any representation at a later date specifying the site difficulties shall not be considered.
The bidder has to fill in his quoted rate against each item in the Bid rate / Unit rate column. If the bidding unit is Above/ Below/ Par, the bidder can select the %Above, %Below or %At Par option from the drop down list in the same column. If the bidding rate is Rs. or Rs./ unit, the bidder has to quote his rate for the item group or individual item accordingly
All the bidders/tenders should ensure that they are GST compliant and their quoted tax structure/rates are as per GST Law
In case of any wrong information submitted by tenderer, the contract shall be terminated, Bid security, Performance Guarantee(PG) and Security Deposit(SD) of contract forfeited and agency barred for doing business on entire Indian Railways for 2(Two) years
Provision of S&T arrangements in connection with shifting of crossovers at VARKALA yard of TVC division.
TVC-SNT-SIG-26-27-26~SR
TVC-SNT-SIG-26-27-26
Open
Works - General
8 Months
Thiruvananthapuram, Kerala
₹0
₹2.2 L
14 Oct 2026
14 Oct 2026
22 Oct 2026
103 items across 1 schedule · ₹81,33,401.7 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | "Submission of all relevent final 'As mades' of circuit diagrams, contact analysis charts, termination particulars of apparatus cases and cable termination rack, power supply arrangements, relay index board, cable plans, cable route plans, red boundary plans and all other particulars covered under various schedules. All 'As mades' shall be prepared by the Contractor in AUTOCAD 2000 or latest and submitted in CDs. One copy of the 'As mades' check print shall be submitted before Testing the circuits. The final negatives shall be made in tracing sheet (80 to 90 gsm). All 'As mades' except cable plan, cable route plan, bonding diagram & power supply diagram shall be prepared in A3 size. On approval the contractor shall submit along with the negatives, 8 copies in each, duly making booklet neatly bound. Out of 8 sets, 2 sets of drawings and other plans shall be kept in transparent plastic cover (2 sheets back to back in one plastic cover) and handed over to Railways. Also the contractor has to supply one set of As mades in 'Reproduction Film'. The approved circuit diagram will be issued by Railways in soft copy as well as two sets of hard copies. Wherever alterations to existing circuits are involved, the existing as-made circuit diagrams will be supplied by Railways either in CDs or RP film. The Contractor shall incoporate the details of all the new wirings and alterations in the CD/ RP film and submit them to Railways. Onapproval 8 copies shall be made for As-made circuit diagrams also as mentioned above" | Sheet 50.00 | — | 382.12 | 19,106 |
| 2 | Supply and Provision of Earthing as per RDSO Specification RDSO/SPN/197/2008 or latest (as per Technical Specification enclosed) | Numbers 2.00 | — | 28,118.51 | 56,237.02 |
| 3 | Provision of earth electrodes as per drawing No.SG/CN/02/13 and earthing of metallic sheath and armour of all cables in all apparatus cases, relay room, equipment room, SM's room for block and control, and earthing of all equipments in apparatus cases, power room, relay rack, cable termination rack, control panel, signals, lever frames with MS flat 35mm X 6mm/19c cable (MS flat for closer by areas and MS flat/19c cable combination for farther areas) as per the instructions of Railway representative at site. The work includes painting of earth resistance value on the earth pit. (Supply of 19C cable is not covered in the scope of this schedule). [MS flat for earthing 35mm X 6mm, cement, GI earth electrodes, common salt, charcoal, country bricks, M sand, soldering materials and all other miscellaneous materials required for the work shall be supplied by the Contractor]. | Numbers 20.00 | — | 1,707.55 | 34,151 |
| 4 | Supply of Low maintenance secondary cells of t h e f o l l o w i n g c a p a c i t i e s w i t h necessary inspection a s p e r specification/ drawing/ description enclosed in this document.b)Supply o f Secondary cells - 2V- 80AH capacity | Numbers 28.00 | — | 3,379.2 | 94,617.6 |
| 5 | Supply of track feed battery charger IRS:S 89- 2013 | Numbers 7.00 | — | 4,375.25 | 30,626.75 |
| 6 | Supply of 'B type choke IRS:S 65-83 | Numbers 14.00 | — | 2,855.6 | 39,978.4 |
| 7 | Supply of 24 Core x 1.5 Sq.mm PVC insulated Armoured, unscreened underground Railway Signalling copper cable as per IRS: S-63/2014 REV.4 | Metre 6000.00 | — | 388.15 | 23,28,900 |
| 8 | S u p p l y o f 1 2 C x 1 . 5 S Q M M P V C insulated Armoured, unscreened underground Railway Signalling copper cable a s per IRS: S-63/2014 REV.4 | Metre 2000.00 | — | 215.92 | 4,31,840 |
| 9 | " S u p p l y o f 2 x 2 5 s q m m P V C insulated Armoured, unscreened underground Railway Signalling Aluminium c a b l e a s p e r I R S : S- 63/2014 REV.4" | Metre 2500.00 | — | 93.01 | 2,32,525 |
| 10 | " S u p p l y o f 2 x 2 . 5 s q . m m P V C insulated Armoured, unscreened, underground Railway S i g n a l l i n g C o p p e r c a b l e a s p e r spec IRS.S.63/2014(Rev.4.0) or latest" | Metre 500.00 | — | 98.76 | 49,380 |
| 11 | Supply o f Underground jelly fi l l e d 6 QUAD, 0.9MM Dia as per spec IRS:TC 30-05 with amd 5 or latest | Metre 2000.00 | — | 301.05 | 6,02,100 |
| 12 | Supply of 24 Fibre armoured OFC cable as per R D S O Specification RDSO/SPN/TC/ 110/2020 Rev. 0 or latest | Metre 1000.00 | — | 95.23 | 95,230 |
| 13 | S u p p l y o f P o l y t h e n e I n s u l a t e d Polythene Sheathed armoured J e l l y Fi l l e d Telephone Cable with Poly-AL Moisture Barrier, 10 Pairs, 0.63 MM Conductor Diameter as per RDSOSpecification N o . IRS:TC-41/97 with amendment 1 or latest | Metre 1000.00 | — | 123.9 | 1,23,900 |
| 14 | Supply a n d provision o f normal j o i n t using Thermo shrink jointing k i t ( R D S O s p e c s No TC/77/2012 ( Rev.3) with amendment No.1&2 o r latest.& jointing k i t t o be inspected by RDSO) f o r 4 / 6 qua d cable normal joint. The work includes excavation of joint p i t o f size 1mX1.5mX1.5m and closing t h e s a m e after completion of cable joint as per the instruction of Railway representative at site. | Numbers 6.00 | — | 4,628.91 | 27,773.46 |
| 15 | Supply of RCC cable markers (Supply of RCC cable markers a s p e r drawing No.CSTE/CN/OFC/1. The lettering o n the cable marker shall be "SIG" / "TELE" / "OFC" as per t h e instructions o f Railway representative at site.) as per drawing enclosed | Numbers 78.00 | — | 262.65 | 20,486.7 |
| 16 | Excavation of cable trench in all kinds of soil except hard rocky areas including clearing of roots of trees, rocks, bushes etc. to a depth of 1.0 Mtrs and to a width of 0.3 Mtrs. (Laying of cables is not included in this schedule) | Metre 2300.00 | — | 64.1 | 1,47,430 |
| 17 | Breaking of Platform concrete having 0.3 feet thickness - 0.5 feet thickness and to a width of 0.3 Mtr using cutter machine and removal of R C C s l a b s o n t h e Passenger Platform, trenching to a depth of 0.6m to accommodate t h e additional cables, replacing the slabs removed after the cables are l a i d and replastering with cement mortar, refilling the trench by ramming and consolidating it as per the instructions of Railway Representatives at site. (Laying o f cables i s n o t included i n this schedule). | Metre 300.00 | — | 2,224.44 | 6,67,332 |
| 18 | Excavation of trench to a depth of 1 Mtr. for track crossing of cables, refilling of trench by ramming a n d consolidating i t a s p e r the instructions of Railway representative at site a f t e r l a y i n g o f D W C / RC C p i p e s . During excavation of trench, it has to be ensured that the excavated soil does not mix with the ballast available. The depth of 1m trench shall b e f r o m t h e b o t t o m o f sleepers for track crossings. Laying o f cables and DWC pipes is not included in this schedule. (Supply of DWC/RCC pipes with couplers/collars is not included in this schedule). | Metre 48.00 | — | 385.45 | 18,501.6 |
| 19 | Excavation of trench to a depth of 1 Mtr. for road crossing of cables, laying of DWC/ RCC pipes with collar/ coupling, refilling of trench b y r a m m i n g a n d consolidating i t and resurfacing it to the original position. Laying of cables is not included in this schedule. (Supply of DWC/RCC pipes with couplers/collars is not included in this schedule). | Metre 18.00 | — | 501.03 | 9,018.54 |
| 20 | Provision of GI pipes (50/100mm dia) for cable laying with offset at both ends and with couplings over RCC bridges, drainage, culverts, and girder bridges. For RCC bridges, drainage, and culverts, the pipes shall be mounted on concrete masonry supports of size 300mm x 300mm x 300mm at an interval of 2 meters. For girder bridges, the pipes shall be fixed on suitable MS clamps at an interval of 2 meters. The ends of the pipes shall be closed with brick masonry abutments to ensure that no cable is exposed. The work shall be carried out as per the instructions of the Railway representative at the site.(Supply of GI pipes with couplings and laying of cables is not included in this schedule).Stone jelly (20/25mm size), bricks, sand, cement, MS angles, flats, bolts, nuts for manufacturing and fixing clamps, bricks, M sand, cement, and other miscellaneous materials for the work shall be supplied by the contractor. | Metre 120.00 | — | 208.54 | 25,024.8 |
| 21 | Laying o f signaling/power/ telecommunication cables a s p e r cable plan in cable trenches, masonry ducts, RCC Pipes, DWC pipes, GI Pipes etc.(Supply o f cables i s n o t included in this schedule). | Metre 12800.00 | — | 18.18 | 2,32,704 |
| 22 | Placing of one row of country bricks of size approximately 2 2 0 m m x 1 0 0 m m x 60mm breadth wise horizontally above the cables in 0.3m width trench.[Country bricks of size 220mm x 100mm x60 mm (approximately) shall be supplied by the Contractor]. | Metre 2300.00 | — | 62.99 | 1,44,877 |
| 23 | "Refilling of cable trench 1m depth by 0.3m width throughout, with earth after laying of c a b l e s , a n d consolidating t h e t r e n c h by ramming and levelling." | Metre 2300.00 | — | 15.4 | 35,420 |
| 24 | "Digging of pit to a depth of 800mm of size 300mmX300mm, c a s t i n g o f concrete foundation o f s i z e 300mmX300mmX300mm and Placing of RCC cable markers on top of t h e foundation a n d r e fi l l i n g t h e p i t and consolidating i t b y r a m m i n g . T h e cable markers shall be provided at an interval of 20 Mtrs. within station limits and 50 Mtrs. outside statio n l i m i t s throughout t h e cable route, diversions a n d a l s o a t every track/road crossing." | Numbers 78.00 | — | 123.35 | 9,621.3 |
| 25 | Excavation o f c a b l e c o i l p i t t o a s i z e of 1 . 5 m x 1 . 5 m a n d d e p t h a s instruc te d by Railway representative at site, for coiling the cables i n r e a r o f r e l a y r o o m s / A F T C huts, apparatus cases etc. The work includes coiling t h e underground cables a n d placing closely o n e layer o f country bricks o f size approx. 220mm x 100mm x 60mm breadth wise above the cables to cover all the cables in the cable pit, closing and consolidating the pit by ramming and levelling.[Country bricks of size 220mmx100mmx60mm (approximately) shall be supplied by the Contractor]. | cum 6.00 | — | 949.05 | 5,694.3 |
| 26 | B l o w i n g / D r a w i n g o f O F C cable/Power cable/Signalling cable inside permanently solid lubricated HDPE Pipe already laid. This work includes necessary duct integrity test for solid l u b r i c a t e d H D P E p i p e . ( This includes Transportation o f materials from nominated stores to site) | Metre 1000.00 | — | 23.43 | 23,430 |
| 27 | Supply of Main LED Signal Aspect - Green as p e r R D S O Specifications No.RDSO/SPN/199/2010 Rev1.1 or latest | Numbers 5.00 | — | 10,030 | 50,150 |
| 28 | Supply of Main LED Signal Aspect - Yellow as per RDSO Specifications RDSO/SPN/199/2010 Rev1.1 or latest | Numbers 5.00 | — | 8,850 | 44,250 |
| 29 | Supply of Main LED Signal Aspect - Red as per R D S O Specifications RDSO/SPN/199/2010 Rev1.1 or latest | Numbers 5.00 | — | 9,233.5 | 46,167.5 |
| 30 | Supply of subsidiary Signal Aspect - Shunt LED as per RDSO Specification SPECIFICATION NO. RDSO/SPN/153/2023 Revision 5.0 or latest | Numbers 10.00 | — | 5,740.7 | 57,407 |
| 31 | Manufacture and supply of Enameled Number p l a t e s a s p e r drawing No.TY/08/2008 with fixing arrangements and fixing the m o n the existing Signals a s per the instructions of Railway representative at site.[Enameled number plates with fixing arrangements with b o l t s a n d n u t s s h a l l be supplied by the Contractor]. | Numbers 6.00 | — | 305.25 | 1,831.5 |
| 32 | Supply of Colour light Signal pole 140mm dia, 4.6m/ 3.6m tall with necessary inspection as p e r s p e c i fi c a t i o n / drawing/ description enclosed in this document. a)Supply o f colour l i g h t S i g n a l p o l e 4 . 6 m tall and 140 mm dia(Galvanised) | Numbers 1.00 | — | 5,841 | 5,841 |
| 33 | Supply of Colour light Signal pole 140mm dia, 4.6m/ 3.6m tall with necessary inspection as p e r s p e c i fi c a t i o n / drawing/ description enclosed in this document. b)Supply o f colour light Signal pole 3 .6 m tall and 140 mm dia (Galvanised) | Numbers 3.00 | — | 4,737.7 | 14,213.1 |
| 34 | Supply of surface base to suit CLS Signal pole 140mm dia with necessary inspection as per specification/ drawing/ description enclosed in this document. | Numbers 4.00 | — | 6,814.5 | 27,258 |
| 35 | Supply of ladder with platform and shoes to suit CLS pole 4.6m/ 3.6m tall, with necessary inspection a s p e r specification/ drawing/ d e s c r i p t i o n e n c l o s e d i n this document. a)Supply o f ladder w i t h platform (4.6m) for CLS(Galvanised) | Numbers 1.00 | — | 5,698 | 5,698 |
| 36 | Supply of ladder with platform and shoes to suit CLS pole 4.6m/ 3.6m tall, with necessary inspection a s p e r specification/ drawing/ d e s c r i p t i o n e n c l o s e d i n this document. b)Supply o f ladder w i t h platform (3.6m) for CLS(Galvanised) | Numbers 3.00 | — | 5,494.5 | 16,483.5 |
| 37 | Supply of post type shunt signal - complete with hood etc., with necessary inspection as p e r s p e c i fi c a t i o n / d r a w i n g / description enclosed in this document. | Numbers 1.00 | — | 5,087.5 | 5,087.5 |
| 38 | Supply of Ground type shunt signal - complete with surface base, signal pole, hood etc., with necessary inspection as per specification/ d r a w i n g / d e s c r i p t i o n enclosed in this document. | Numbers 2.00 | — | 7,463.5 | 14,927 |
| 39 | Supply of Colour Light Signal Multi Unit type- complete for 4/ 3/ 2 aspect with mounting s o c k e t , w i t h necessary inspection a s per specification/ drawing/ description enclosed in this document. b)Supply of colour light Signal unit (3 aspect) | Numbers 2.00 | — | 16,874 | 33,748 |
| 40 | Supply of Colour Light Signal Multi Unit type- complete for 4/ 3/ 2 aspect with mounting s o c k e t , w i t h necessary inspection a s per specification/ drawing/ description enclosed in this document. c)Supply of colour light Signal unit (2 aspect) | Numbers 2.00 | — | 14,278 | 28,556 |
| 41 | Supply of Junction type route indicator - 5 unit arm - 1/ 2/ 3/ 4/ 5/ 6 way with mounting sockets, with necessary inspection as per specification/ drawing/ description enclosed in this document. a) Supply of Junction type route indicator - 1 way | Numbers 1.00 | — | 15,121.7 | 15,121.7 |
| 42 | Supply of Calling On Signal / 'A' marker light - complete with necessary inspection as per specification/ drawing/ description enclosed in this document. a)Supply of Calling On Signal | Numbers 1.00 | — | 3,663 | 3,663 |
| 43 | Supply of Signal post telephone with facility of p a g i n g a n d t a l k - b a c k i n c l u d i n g voice communication e q u i p m e n t w i t h suitable switching arrangement at the Signal post and at SM's room a s per specification enclosed in this document. This includes drawl of tail cable through G I pipe 25mm dia and 2 mtrs long duly clamped to Signal post w i t h b e n d as required a t site, termination of tail cable at one end in the apparatus case and other end in the console. In the SM's room, console shall be fixed on a table top. T h e wiring shall be done using wire PVC 16/0.2mm copper. [Talk- bac k equipment complete including housing b o x , w i r e P V C 16/0.20mm a n d all other miscellaneous materials required for the work shall be supplied by the Contractor]. | Numbers 1.00 | — | 11,897.35 | 11,897.35 |
| 44 | Supply of KLCR relays 24V, ACI (Supply of Key Lock Checking Relay (KLCR) with one number K-50 neutral Relay to work on 24V DC non AC immunized a s p e r specification No.RDSO/SPN/219/2016 Ver 1.0 with Amdt-1 o r latest (with o n e extra ward plate andwith case) contact configuration-4F/4B and as per IRS:S-23, IRS:S@58"44@ IRS:46 or latest. | Numbers 10.00 | — | 10,722.72 | 1,07,227.2 |
| 45 | Supply of Relay, Non-AC Immune, plug-in type , Style 'QN1',DC neutral line, 50V, 8F.8B contacts front and back contacts metal to carbon with plug board , retaining clip & connectors confirming to BRS:930, IRS:S 34 & IRS:S 23 or latest. The interlocking code for this unit shall be ABDEF. | Numbers 12.00 | — | 4,484 | 53,808 |
| 46 | Supply of Relay, AC Immune, plug-in-type, Style 'QNA1', DC Neutral line, 24V, 8F.8B contacts, front and back contacts metal to carbon, with plug board, retaining clip and connectors confirming to BRS:931A, IRS:S 60, IRS:S 34 and IRS:S 23 or latest. The interlocking code for this unit shall be ABDGH. | Numbers 64.00 | — | 4,639.03 | 2,96,897.92 |
| 47 | Supply of lamp proving relays(QECX-61) for a)LED aspects w ith p l u g boards, connectors and retaining clips with necessary inspection as per specification/ | Numbers 20.00 | — | 5,901.5 | 1,18,030 |
| 48 | Supply of QBCA1 - heavy duty contact relays with necessary inspection as per specification/ | Numbers 4.00 | — | 6,613.75 | 26,455 |
| 49 | Manufacture and supply of M.S. relay frames of suitable size to hold up to 4/ 8/ 12/ 2 0 relays /plug i n t y p e a s required by Railways and fixing them in apparatus cases for all types of signal control circuits, LC gate control circuit and Point control circuits, fixing of plug boards, relays, resistors and electrolytic condensers on Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, wiring and termination as per approved circuit diagram and painting the particulars.[Wire PVC copper, 3/0.75mm and 16/0.2mm coppe r, Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, for fixing resistors and condensers, M S fl a t s 2 5 m m x 6 m m brass bolts a n d nuts, paints, soldering materials, resistors, condensers a n d a l l other miscellaneous materials required for the work shall be supplied by the contractor]. a)Wiring of Signal/ point/ LC control circuit (up to 4 relays/Plug in type) | Set 3.00 | — | 4,945.51 | 14,836.53 |
| 50 | Manufacture and supply of M.S. relay frames of suitable size to hold up to 4/ 8/ 12/ 2 0 relays /plug i n t y p e a s required by Railways and fixing them in apparatus cases for all types of signal control circuits, LC gate control circuit and Point control circuits, fixing of plug boards, relays, resistors and electrolytic condensers on Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, wiring and termination as per approved circuit diagram and painting the particulars.[Wire PVC copper, 3/0.75mm and 16/0.2mm coppe r, Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, for fixing resistors and condensers, M S fl a t s 2 5 m m x 6 m m brass bolts a n d nuts, paints, soldering materials, resistors, condensers a n d a l l other miscellaneous materials required for the work shall be supplied by the contractor]. b)Wiring o f Signal/ Point/ L C control circuit (up to 8 relays/plug in type) | Set 4.00 | — | 8,786.26 | 35,145.04 |
| 51 | Manufacture and supply of M.S. relay frames of suitable size to hold up to 4/ 8/ 12/ 2 0 relays /plug i n t y p e a s required by Railways and fixing them in apparatus cases for all types of signal control circuits, LC gate control circuit and Point control circuits, fixing of plug boards, relays, resistors and electrolytic condensers on Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, wiring and termination as per approved circuit diagram and painting the particulars.[Wire PVC copper, 3/0.75mm and 16/0.2mm coppe r, Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, for fixing resistors and condensers, M S fl a t s 2 5 m m x 6 m m brass bolts a n d nuts, paints, soldering materials, resistors, condensers a n d a l l other miscellaneous materials required for the work shall be supplied by the contractor]. c)Wiring o f Signal/ Point/ L C control circuit (up to 12 relays/plug in type) | Set 1.00 | — | 11,355.02 | 11,355.02 |
| 52 | Manufacture and supply of M.S. relay frames of suitable size to hold up to 4/ 8/ 12/ 2 0 relays /plug i n t y p e a s required by Railways and fixing them in apparatus cases for all types of signal control circuits, LC gate control circuit and Point control circuits, fixing of plug boards, relays, resistors and electrolytic condensers on Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, wiring and termination as per approved circuit diagram and painting the particulars.[Wire PVC copper, 3/0.75mm and 16/0.2mm coppe r, Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, for fixing resistors and condensers, M S fl a t s 2 5 m m x 6 m m brass bolts a n d nuts, paints, soldering materials, resistors, condensers a n d a l l other miscellaneous materials required for the work shall be supplied by the contractor]. d)Wiring o f Signal/ Point/ L C control circuit (up to 20 relays/Plug in type) | Set 2.00 | — | 13,597.41 | 27,194.82 |
| 53 | Supply of QTA2 - track relays with plug boards, connectors and retaining clips with necessary inspection as per specification | Numbers 10.00 | — | 4,070 | 40,700 |
| 54 | Supply of QSPA1 type relays with plug boards, connectors and retaining clips with necessary inspection as per specification/drawing/ | Numbers 10.00 | — | 7,139 | 71,390 |
| 55 | Fabrication and Supply of box suitable for 4 Nos of KLCRs | Numbers 10.00 | — | 15,009.6 | 1,50,096 |
| 56 | Fixing o f PBT terminal block/ P B T fuse block, rubber grommets, clamping of cables using teakwood c a b l e c l a m p s a n d base planks, termination o f cables, provision of ND type f u s e s o f required capacities, provision of copper b u s b a r f o r supply terminals, wiring, provision o f termination particulars diagram b o a r d u s i n g plywood of thickness 1 2 m m - teakwood finish o f size 1800mm x 1200mm with Aluminium grooved channel frame i n the relay room. The blank spaces over the top of the cable termination rac k shall b e covered with phynolic s h e e t o f t h i c k n e s s 3mm wherever required. The termination and cable core particulars shall b e painted o n t h e PVC/ n y l o n s l e e v e s . T h e w o r k a l s o includes identification of cables using aluminium tags provided on each cable with letters punched neatly.(Supply of PBT terminal blocks 25mm & 6 0 m m centers a n d P B T Fu s e blocks i s not covered in the schedule) [Wire PVC 3/0.75mm copper, brass bolts and nuts and washers, for fixing PBT terminal/Fuse Block, o t h e r fixing bolts and nuts, rubber grommets, PVC/ Nylon sleeves, copper bus bars, teakwood 50mm x 50mm for cable clamps, 25mmx 100mm for base planks, phynolic sheet 6mm thick of size 1200mm x 1800mm with aluminium grooved channel f r a m e , phynolic s h e e t 3 m m thick, paint a n d a l l other miscellaneous materials shall be supplied by the Contractor]. a)Fixing of PBT terminal blocks (25mm/60mm centre) and termination (Per Unit = Per Terminal Block) | Per Unit 500.00 | — | 167.99 | 83,995 |
| 57 | Fixing o f PBT terminal block/ P B T fuse block, rubber grommets, clamping of cables using teakwood c a b l e c l a m p s a n d base planks, termination o f cables, provision of ND type f u s e s o f required capacities, provision of copper b u s b a r f o r supply terminals, wiring, provision o f termination particulars diagram b o a r d u s i n g plywood of thickness 1 2 m m - teakwood finish o f size 1800mm x 1200mm with Aluminium grooved channel frame i n the relay room. The blank spaces over the top of the cable termination rac k shall b e covered with phynolic s h e e t o f t h i c k n e s s 3mm wherever required. The termination and cable core particulars shall b e painted o n t h e PVC/ n y l o n s l e e v e s . T h e w o r k a l s o includes identification of cables using aluminium tags provided on each cable with letters punched neatly.(Supply of PBT terminal blocks 25mm & 6 0 m m centers a n d P B T Fu s e blocks i s not covered in the schedule) [Wire PVC 3/0.75mm copper, brass bolts and nuts and washers, for fixing PBT terminal/Fuse Block, o t h e r fixing bolts and nuts, rubber grommets, PVC/ Nylon sleeves, copper bus bars, teakwood 50mm x 50mm for cable clamps, 25mmx 100mm for base planks, phynolic sheet 6mm thick of size 1200mm x 1800mm with aluminium grooved channel f r a m e , phynolic s h e e t 3 m m thick, paint a n d a l l other miscellaneous materials shall be supplied by the Contractor]. b)Termination using P B T fuse block i n cable termination rack (Per Unit = Per Fuse Block) | Per Unit 20.00 | — | 201.27 | 4,025.4 |
| 58 | Fixing of plug boards, 5 0 way terminal blocks with 2BA terminals, and wiring of relays as per the approved circuit diagram using wire PVC 16/0.2mm copper. Suitable wire supporting tray with cover made of PVC shall be provided horizontally and vertically in the relay racks.. While running the wires on the aluminium ladder proper care shall be taken t o provide smooth materials like rubber beading in the openings on Phynolic sheets, to avoid damage to wires. The work also includes wiring of contacts for data logger and terminating them i n tag blocks, provision of relay index board. (Supply of relays, plug boards, connectors and retaining clips is not covered in this schedule). [Wire PVC 16/0.2mm copper, t a g blocks, 2BA terminals, hard wood plank o f size 600mmx 900mmx25mm with decolum finish, MS angles of size 25mmX25mmX6mm, relay fixing bolts and nuts, teakwood plank 25mm thick for fixing resistors and condensers, phynolic sheet 6 m m t h i c k o f s i z e 1200mmX1800mm with aluminium grooved channel frame f o r relay i n d e x b o a r d , p a i n t s , s o l d e r i n g materials, b u n c h i n g t h r e a d , w i r e w o u n d resistance, condenser, wire supporting tray with cover of suitable size made of PVC, paint, varnish and all other miscellaneous materials required for the work shall be supplied by the Contractor]. | Per Relay 8.00 | — | 1,045.76 | 8,366.08 |
| 59 | Carrying out alterations t o the existing relays in the relay racks/apparatus cases as per the approved circuit diagram using wire PVC 16/0.2mm copper. The work includes painting alterations and releasing the unwanted wires c a r e f u l l y w i t h o u t disturbing the existing wiring.[Wire PVC 16/0.2mm copper, soldering m ateria ls, b u n c h i n g t h r e a d s , condensers, resistances a n d teakwood p l a n k f o r fixing the m a n d a l l other miscellaneous materials required for the work shall be supplied by the Contractor]. | Per Relay 16.00 | — | 695.67 | 11,130.72 |
| 60 | Supply o f Double walled corrugated p i p e - 1 0 3 . 5 m m i n n e r d i a & 1 2 0 m m o u t e r dia conforming t o specification No. IS 14930(Part 2): 2001 with one coupler for every 6m of pipe as per Technical specification | Metre 66.00 | — | 365.19 | 24,102.54 |
| 61 | Supply o f G I pipes - 100mm dia-4.5mm thick as per Technical specification | Metre 120.00 | — | 1,119.16 | 1,34,299.2 |
| 62 | Supply of HDPE Pipe 40mm (outer dia)/33 mm (inner dia) with couplers | Metre 1000.00 | — | 60.93 | 60,930 |
| 63 | Supply of track lead junction box - FRP type with 4 terminals and stumps with necessary inspection a s p e r specification/ drawing/ description enclosed in this document. | Numbers 24.00 | — | 1,622.5 | 38,940 |
| 64 | Supply of Track Feed Resistance | Numbers 10.00 | — | 287.77 | 2,877.7 |
| 65 | Supply of PBT terminals 25mm/ 60mm centre and PBT Fuse blocks with necessary inspection a s p e r specification/ drawing/ description enclosed in this document. a)Supply of PBT terminals 25mm centre. | Numbers 850.00 | — | 61.44 | 52,224 |
| 66 | Supply of PBT terminals 25mm/ 60mm centre and PBT Fuse blocks with necessary inspection a s p e r specification/ drawing/ description enclosed in this document. b)Supply of PBT terminals 60mm centre. | Numbers 200.00 | — | 93.02 | 18,604 |
| 67 | Supply of PBT terminals 25mm/ 60mm centre and PBT Fuse blocks with necessary inspection a s p e r specification/ drawing/ description enclosed in this document. c)Supply of PBT fuse block without ND fuse | Numbers 50.00 | — | 103.84 | 5,192 |
| 68 | S u p p l y o f 3/0.75mm o r 4 S q . m m Copper cable(per unit=100 mtrs) APC) | Per Unit 10.00 | — | 3,459.5 | 34,595 |
| 69 | S u p p l y o f 1 6 / 0 . 2 m m copper cable(per unit=100 mtrs)ATC) | Per Unit 10.00 | — | 1,327.19 | 13,271.9 |
| 70 | Excavation of pit, erection of cable termination boxes on rails and concreting as per Drg. No.SG/CN/02/8, drilling of suitable holes in the box, fixing of 2 Nos. of GI pipes 32mm dia and 300mm long a t the bottom with clamp nuts - 12 mm thick, one at the inner side and another at the outer side for each p i p e for c a b l e e n t r y a n d o n e G I pipe 150mm long 32mm dia for drawl of jumper wires for Point machines etc., fixing of hardwood plank 37mm thick on the bottom, provision of one EWS lock, and painting the boxes i n s i d e and outside w ith o n e coa t of red-oxide a n d two coats of aluminium paints. | Numbers 4.00 | — | 5,029.69 | 20,118.76 |
| 71 | Installation of combined type point machine- I R S t y p e a n d c o n n e c t i n g a l l ground connections including wiring and termination i n p o i n t m a c h i n e a n d interconnections between point machine and CT box through PVC hose pipe with 3/0.75mm and 7/1.40mm copper wire a n d painting. This work includes provision of insulation to stretcher bars, throw b a r l u g a n d "D" bracket wherever required, cutting of notches on the point machines covers to suit crank handle configuration. (Combined type point machine with ground connection, uninsulated stretcher bar, throw bar lug and 'D' brackets will be supplied by Railways.[All types of insulations connected to point work, coal bengal, all type of bolts and nuts, washers spring/flat w i r e P V C 7/1.4mm copper, P V C h o p e p i p e , paints, PVC/nylon sleeves and all other miscellaneous materials required for the work shall be supplied by the Contractor]. | Numbers 4.00 | — | 16,383.88 | 65,535.52 |
| 72 | Installation of Signal post telephone (paging and talk back) | Numbers 1.00 | — | 5,392.75 | 5,392.75 |
| 73 | Excavation o f pit,casting concrete foundation as per Drg.No.SG/CN/02/9 using metallic templates, for erection o f colour light signals up to 4 aspects.[Foundation bolts, cement, M sand, stone jelly o f size 20/25mm dia and all other miscellaneous materials required for the work shall be supplied by the Contractor]. | Numbers 4.00 | — | 9,213.28 | 36,853.12 |
| 74 | " E r e c t i o n o f s u r f a c e b a s e , s i g n a l pole, mounting of colour light signal up to 4 aspects complete o n Signal pole/ Off-set bracket, (for LED / filament bulbs) with lenses, triple pole l a m p holder, filament switching u n i t s , CLS transformer, current regulators (whichever is applicable), fixing of ladder w i t h platform complete and concreting of ladder shoe, fixing o f number plates, marker board, lens guard, fi x i n g of speed l i m i t b o a r d wherever necessary, termination of tail cables, wiring of signal unit w ith P V C w ire 3/0.75mm copper, provision of EWS locks, and painting of one coat of red oxide and two coats of aluminium/ enamel paints. When the aspect is fixed on Offset bracket using 'U' bolts and nuts, a through bolt shall be provided by drilling a hole in the signal pole to prevent the offset bracket from sliding down.(Supply of surface base, Offset bracket, CLS pole, C L S aspects complete, ladder with shoes and platform, Speed limit board, LED aspects, current regulators, l a m p holders, lamps, filament switching u n i t a n d CLS transformer is not covered in this schedule).['U' bolts and nuts, through bolts and nuts, cement, stone jelly 20/25mm dia, M sand, Signal Collar Rings, wire P V C 3/0.75mm copper, lens-guard, all fixing bolts and nuts, lead wool, paints PVC/Nylon sleeves, enameled number plates. enameled marker boards, E W S l o c k s , a n d a l l other miscellaneous materials for the work shall be supplied by the Contractor]." | Numbers 4.00 | — | 8,287.08 | 33,148.32 |
| 75 | "Excavation o f p i t a n d c a s t i n g concrete foundation a s per Drg, No.SG/CN/02/10 using metallic templates, for erection of ground type colour light shunt signal. [Foundation bolts and nuts, cement, M sand, stone j e l l y o f size 2 0 / 2 5 m m a n d a l l other miscellaneous materials for the work shall be supplied by the Contractor]." | Numbers 2.00 | — | 4,645.17 | 9,290.34 |
| 76 | " E r e c t i o n o f G r o u n d t y p e s h u n t signal complete including surface base, signal pole, L E D a s p e c t s / l e n s e s , b u l b s w i t h holders (whichever is applicable), fixing of lens guards, number plate, termination of tail cables, wiring of signal unit with PVC wire 3/0.75mm copper, provision o f E W S locks and painting o f one coat of red oxide and two coats of Aluminium/ enamel paint.(Supply o f Ground t y p e shunt signal complete including surface base, signal pole, LED aspects, holder, bulbs, and lenses is not covered i n t h i s schedule).[Wire PVC 3/0.75mm copper, l e n s guards, E W S locks, Enameled number plates, bolts and nuts, lead wool, paints and all other miscellaneous materials shall be supplied by the Contractor]." | Numbers 2.00 | — | 3,170.44 | 6,340.88 |
| 77 | Fixing o f Offset brackets using 'U' bolts and n u t s , erection o f P o s t t y p e s h u n t Signals, termination of tail cables and wiring using wire PVC 3/0.75mm copper, provision of EWS lock and painting of one coat of red-"oxide and two coats of aluminium/ enameled paint. The work also includes drilling suitable holes on the CLS post and provision of a through bolt with nut to prevent the Off-setbracket from slipping down." | Numbers 1.00 | — | 2,306.03 | 2,306.03 |
| 78 | Fixing of Offset brackets using 'U' bolts and nuts, erection of Calling On Signals/ 'A' marker lights, termination of tail cables and wiring using wire PVC 3/0.75mm copper, provision of EWS lock, number plates/ marker boards and painting. T h e w o r k also includes drilling suitable holes on the CLS post and provision of a through bolt with nut to prevent the Off-set bracket from slipping down.(Supply o f Calling on Signal/ 'A' marker light, LED aspects/holders & bulbs and Off set brackets is not covered in this schedule).['U' b o l t s a n d n u t s , through bolts w i t h nut, wire P V C 3/0.75mm copper, E W S lock, Enameled n u m b e r p l a t e s , wire mesh, PVC/Nylon sleeves, paints and all other miscellaneous materials shall be supplied by the contractor]. | Numbers 1.00 | — | 2,081.25 | 2,081.25 |
| 79 | Provision of DC Single/ Double rail track circuit to suit RE/ Non-RE areas as per approved signaling plan using Plug-in type track relays. This work includes provision of double bonding, and parallel jumpers, provision of bond wire clips, provision of track lead connections using 2c X 2.5 sq.mm cable, provision of TLD boxes 2 Nos. at Relay end, 2 Nos. at Feed end and 2 No's for parallel jumpers as necessary to suit layouts, for each Track Circuit, and termination of jumpers and tail cables in track lead junction boxes, installation of relays, track feed battery chargers to charge up to 4 cells, track feed resistance, 'B' type choke' and secondary cells - 80 AH capacity in apparatus cases and wiring with wire PVC 3/0.75mm copper. The work also includes painting of track Circuit No. with Feed end/ Relay end details on the TLD boxes. The work also includes provision of insulations for gauge tie plates and nose crossing plates wherever required. (Provision of rail joint insulation is not covered in this schedule.) (Uninsulated gauge type plate and nose crossing plate will be supplied by Railways. Supply of track feed battery charger, 'B' type choke, track relays, un-charged secondary cells (2V - 80AH), TLD boxes with stumps,2cX2.5 sq.mm cable, is not covered in this schedule). a)Provision of track circuit in RE/Non RE area (point zone) | Numbers 4.00 | — | 8,914.5 | 35,658 |
| 80 | Provision of DC Single/ Double rail track circuit to suit RE/ Non-RE areas as per approved signaling plan using Plug-in type track relays. This work includes provision of double bonding, and parallel jumpers, provision of bond wire clips, provision of track lead connections using 2c X 2.5 sq.mm cable, provision of TLD boxes 2 Nos. at Relay end, 2 Nos. at Feed end and 2 No's for parallel jumpers as necessary to suit layouts, for each Track Circuit, and termination of jumpers and tail cables in track lead junction boxes, installation of relays, track feed battery chargers to charge up to 4 cells, track feed resistance, 'B' type choke' and secondary cells - 80 AH capacity in apparatus cases and wiring with wire PVC 3/0.75mm copper. The work also includes painting of track Circuit No. with Feed end/ Relay end details on the TLD boxes. The work also includes provision of insulations for gauge tie plates and nose crossing plates wherever required. (Provision of rail joint insulation is not covered in this schedule.) (Uninsulated gauge type plate and nose crossing plate will be supplied by Railways. Supply of track feed battery charger, 'B' type choke, track relays, un-charged secondary cells (2V - 80AH), TLD boxes with stumps,2cX2.5 sq.mm cable, is not covered in this schedule). b)Provision of track circuit in RE/Non RE area (other than point zone) | Numbers 3.00 | — | 7,145.44 | 21,436.32 |
| 81 | Alteration to existing DC Track Circuits to suit RE/Non RE standard as per approved signaling plan. This w ork includes provision of double bonding a n d parallel jumpers, provision of bond wire clips, wherever required, shifting of relay end and feed end equipments and re- wiring them, provision of track lead connections wherever necessary using 2c x 2.5 sq.mm cable. a)Alteration to existing track circuits at feed end | Numbers 2.00 | — | 4,234.65 | 8,469.3 |
| 82 | Alteration to existing DC Track Circuits to suit RE/Non RE standard as per approved signaling plan. This w ork includes provision of double bonding a n d parallel jumpers, provision of bond wire clips, wherever required, shifting of relay end and feed end equipments and re- wiring them, provision of track lead connections wherever necessary using 2c x 2.5 sq.mm cable b)Alteration to existing track circuits at relay end | Numbers 2.00 | — | 3,850.31 | 7,700.62 |
| 83 | Excavation of pit, casting concrete foundation and erection of apparatus case full size as per Drg. No.SG/CN/02/6 and fixing of 2 Nos. of 'E' type locks, one for the front door and another for the back door, fixing of one hard wood shelf plank 37mm thick and painting the apparatus case inside and outside with one coat of red- oxide and two coats of aluminium paints. (Supply of apparatus case is not included in this schedule).[Foundation bolts & n u t s , 'E' type locks, cement, M sand, stone jelly of size 20/25 mm, hardwood plank of 37mm thick, paints, varnish, fixing bolts & nuts and all other miscellaneous materials required f o r thework shall be supplied by the Contractor.] | Numbers 9.00 | — | 11,333.1 | 1,01,997.9 |
| 84 | "Excavation of pit, casting concrete foundation and erection of apparatus case half size as per Drg, No.SG/CN/02/7, fixing one 'E' type lock for t h e front door and latching arrangement for the back door, and fixing o f o n e hardwood s h e l f p l a n k 37mm thick and painting the apparatus case inside and outside with one coat of red-oxide and two coats of aluminium paints.(Supply of apparatus case is not included in this schedule).[Foundation bolts and nuts, cement, 'E' type locks, M sand, stone jelly of size 20/25mm,37mm hard wood planks, latching ""arrangements, paints, varnish, fixing bolts & nuts a n d a l l other miscellaneous materials required for the work shall be supplied by the Contractor]""" | Numbers 5.00 | — | 8,787.04 | 43,935.2 |
| 85 | Excavation of pit, erection of cable termination boxes on rails and concreting as per Drg. No.SG/CN/02/8, drilling of suitable holes in the box, fixing of 2 Nos. of GI pipes 32mm dia and 300mm long a t the bottom with clamp nuts - 12 mm thick, one at the inner side and another at the outer side for each p i p e for cable throughing, fi x i n g of hardwood plank 37mm thick on the bottom, provision of one EWS lock, and painting the boxes inside and outside w ith o n e coa t of red-oxide a n d two coats of aluminium paints.(Supply of CT boxes i s n o t covere d i n this schedule. R a i l s of different length shall be supplied by Railways. The contractor shall cut lengthy rails wherever required.)[Cement, M sand, stone jelly o f size 20/25mm, paint, varnish, G I Pipes 32mm dia with clamp nuts - 12mm thick - 2 Nos. for each pipe, fixing bolts and nuts with washers, EWS l o c k s , p a i n t s a n d a l l other miscellaneous materials shall be supplied by the Contractor]. | Numbers 4.00 | — | 4,999.16 | 19,996.64 |
| 86 | Excavation of pit in and around the existing l o c a t i o n b o x e s v e r y c a r e f u l l y without damaging the working cables and shifting and turning the location boxes to clear of the infringement a s instructed b y t h e Railway representative a t s i t e . T h e w o r k includes ensuring the safety of the signaling system, releasing t h e cable coils t o g i v e access for shifting/turning the location boxes. Necessary masonry work and earth work in and around the location boxes t o the required level shall be done as instructed by the Railway representative a t site. I f the existing earth connections t o t h e location boxes are disturbed, the earth wires shall be properly re- connected. a) Shifting of apparatus case (full) | Numbers 1.00 | — | 5,348.81 | 5,348.81 |
| 87 | Excavation of pit in and around the existing l o c a t i o n b o x e s v e r y c a r e f u l l y without damaging the working cables and shifting and turning the location boxes to clear of the infringement a s instructed b y t h e Railway representative a t s i t e . T h e w o r k includes ensuring the safety of the signaling system, releasing t h e cable coils t o g i v e access for shifting/turning the location boxes. Necessary masonry work and earth work in and around the location boxes t o the required level shall be done as instructed by the Railway representative a t site. I f the existing earth connections t o t h e location boxes are disturbed, the earth wires shall be properly re- connected. b) Shifting of apparatus case (half) | Numbers 1.00 | — | 3,545.06 | 3,545.06 |
| 88 | Termination o f n e w main/tail cables o n the existing terminals/ fuse blocks in apparatus c a s e s / b a t t e r y b o x e s / C T b o x e s / cable termination r a c k s a s p e r approved circuit diagram. T h e terminal particulars a r e to be repainted /corrected on the doors of apparatus cases/ battery boxes/ cable termination boxes and FTOT index board as instructed by Railway representative at site. This work includes closing the opening created for entry o f n e w cables i n the apparatus cases with masonry brick work and sealing the bottom of the apparatus cases/ cable termination racks w i t h cable compound.[Paints, wire PVC 3/0.75mm and 16/0.2mm copper, sealing compound, bricks, cement, M sand and all other required miscellaneous materials shall be supplied by the contractor].(Per Unit = Per Terminal block) | Per Unit 500.00 | — | 73.59 | 36,795 |
| 89 | Termination of main, tail, Signaling and power cables a n d internal wiring on terminal/ fuse b l o c k s i n n e w apparatus cases, cable termination b o x e s a n d i n gate Lodges excluding c a b l e termination r a c k at relay r o o m . The work includes fixing of all new cables by teakwood clamp on teakwood base plank, fixing o f Phynolic synthetic industrial fibre base fine weave cotton fibre board 6mm thick for terminal board to suit each apparatus case, varnishing all teakwood items, fixing of terminals/ fuse blocks o n t h e terminal board, drilling of necessary h o l e s , termination of cables, wiring, identification o f cables using aluminium tags with letters punched neatly, a s p e r approved circuit diagram a n d cable plan, painting of particulars on sleeves andalso o n t h e inner side o f t h e doors of apparatus cases. After terminations are "over, t h e side openings of apparatus case foundation shall be closed with brick work, cement plastered, the inter-space filled with M sand up to base level a n d t h e bottom surface shall b e sealed with sealing compound.(Supply of PBT terminals and Fuse blocks is not c o v e r e d i n this schedule)." a)Termination o n 25/60mm PBT terminals (new location)(Phynolic sheet)(Per Unit = Per Terminal block) | Per Unit 800.00 | — | 172.14 | 1,37,712 |
| 90 | Termination of main, tail, Signaling and power cables a n d internal wiring on terminal/ fuse b l o c k s i n n e w apparatus cases, cable termination b o x e s a n d i n gate Lodges excluding c a b l e termination r a c k at relay r o o m . The work includes fixing of all new cables by teakwood clamp on teakwood base plank, fixing o f Phynolic synthetic industrial fibre base fine weave cotton fibre board 6mm thick for terminal board to suit each apparatus case, varnishing all teakwood items, fixing of terminals/ fuse blocks o n t h e terminal board, drilling of necessary h o l e s , termination of cables, wiring, identification o f cables using aluminium tags with letters punched neatly, a s p e r approved circuit diagram a n d cable plan, painting of particulars on sleeves andalso o n t h e inner side o f t h e doors of apparatus cases. After terminations are "over, t h e side openings of apparatus case foundation shall be closed with brick work, cement plastered, the inter-space filled with M sand up to base level a n d t h e bottom surface shall b e sealed with sealing compound.(Supply of PBT terminals and Fuse blocks is not c o v e r e d i n this schedule)." b)Termination o n P B T fuse block (new location) (Phynolic sheet)(Per Unit = Per Fuse block) | Per Unit 20.00 | — | 209.93 | 4,198.6 |
| 91 | Termination of main, tail, Signaling and power cables and internal wiring b y fixing additional terminals/ fuse blocks on the existing terminal boards of apparatus cases, cable termination boxes etc. The work includes fixing of all new cables by teakwood clamp o n teakwood base plank, varnishing all teakwood items, fixing of terminals/ fuse blocks, on the existing terminal boards, drilling of necessary holes, termination of cables, wiring, identification of cables using aluminium tags with letters punched neatly, a s p e r approved circuit diagram a n d cable plan, painting o f particulars o n sleeves and also on the inner side of the doors of apparatus cases. After terminations are over, t h e side openings of apparatus case foundation shall be closed with brick work, cement plastered, the inter-space filled with M sand up to base level a n d t h e bottom surface shall b e sealed with sealing compound. a)Termination of cables on 25/60mm PBT terminals (existing location)(Per Unit = Per Terminal block) | Per Unit 300.00 | — | 151.09 | 45,327 |
| 92 | Termination of main, tail, Signaling and power cables and internal wiring b y fixing additional terminals/ fuse blocks on the existing terminal boards of apparatus cases, cable termination boxes etc. The work includes fixing of all new cables by teakwood clamp o n teakwood base plank, varnishing all teakwood items, fixing of terminals/ fuse blocks, on the existing terminal boards, drilling of necessary holes, termination of cables, wiring, identification of cables using aluminium tags with letters punched neatly, a s p e r approved circuit diagram a n d cable plan, painting o f particulars o n sleeves and also on the inner side of the doors of apparatus cases. After terminations are over, t h e side openings of apparatus case foundation shall be closed with brick work, cement plastered, the inter-space filled with M sand up to base level a n d t h e bottom surface shall b e sealed with sealing compound. b)Termination of cables on P B T fuse block (existing location)(Per Unit = Per Fuse block) | Per Unit 10.00 | — | 188.86 | 1,888.6 |
| 93 | Installation of charged secondary cells of the f o l l o w i n g c a p a c i t i e s i n a p p a r a t u s cases, connecting them with strips, wiring with wire PVC 3/0.75mm copper and termination. This work also includes charging of cells through reputed agencies. The details of the batteries shall be written on the inside of the doors of the apparatus cases.(Supply of secondary cells is not included in this schedule).[Wire PVC 3/0.75mm copper, connecting strips, paint a n d a l l other miscellaneous materials required for the work shall be supplied by the Contractor]. b)Installation of 2V-40/80AH cells in apparatus cases(Per Unit = Per Cell) | Per Unit 28.00 | — | 491.59 | 13,764.52 |
| 94 | Carrying out alterations to the existing SM's control panel. T h e w o r k includes drilling of holes o n t h e To p p l a t e wherever required, fixing and wiring o f knobs, buttons, counters, LEDs with holder, closing of unwanted holes, carrying out painting alterations on the panel, termination of additional cables and carrying out alteration to the existing wiring as per approved circuit diagram, releasing of unused wires, and painting of particulars as per the instructions of Railway representative at site. (Supply of knobs, buttons and counters is not included in the scope of this schedule). [LED lamps with holder, paint, soldering materials and all other miscellaneous materials required f o r t h e w o r k s h a l l be supplied by the Contractor]. | Lumpsum 1.00 | — | 15,967.35 | 15,967.35 |
| 95 | Painting, erection a n d concreting o f Goods warning boards on rails as per the Signalling p l a n . T h e w o r k includes manufacturing of clamps and fixing the board to the rails, supply and fixing of scotch lite reflectors and concreting the rail post to a size of 600mm x 600mmx900mm. (Supply o f g o o d s warning boards are not covered in this schedule. Rails o f different lengths will be supplied by Railways and the Contractor has t o c u t them t o t h e required lengths).[Stone jelly o f size 2 0 /2 5 m m d i a , M sand, cement, M.S.flats, scotch lite strips (14 Nos) for e a c h board, fi x i n g b o l t s a n d n u t s , paint and a l l other miscellaneous materials shall be supplied by the Contractor]. | Numbers 1.00 | — | 5,398.39 | 5,398.39 |
| 96 | Provision of HDPE Pipe of dia 40/33 mm | Metre 1000.00 | — | 26.11 | 26,110 |
| 97 | "Breaking of concrete and releasing of STOP board/Warning board/ LEGEND boards along w i t h r a i l s , accounting a n d stacking them neatly a t a place a s instructed b y Railway representative at site. Also the resultant pits s h a l l b e re-surfaced a n d consolidating by ramming and levelling" | Numbers 3.00 | — | 1,580.36 | 4,741.08 |
| 98 | Releasing o f existing apparatus cases (Full/ H a l f / Q u a r t e r s i z e ) w i t h o u t d a m a g e after releasing the shelf planks, Terminal blocks, Fu s e Blocks, Terminal Boards, Relays o f all t y p e s E K T s , S e c o n d a r y Cells, power equipments, 'E' type locks, etc., and breaking t h e concrete foundation. After releasing, the resultant pits are to be closed and consolidated by ramming and levelling. The released materials s h a l l b e accounted and stacked a t a place a s instructed by Railway representative at site. | Numbers 13.00 | — | 3,006.71 | 39,087.23 |
| 99 | Breaking of concrete and releasing the existing cable termination boxes, after releasing the b a s e p l a n k , Terminal blocks, Fuse Blocks, Terminal Boards, cut rails, pipes, etc., closing t h e resultant p i t s and consolidating i t by ramming and levelling. The released materials shall b e accounted and stacked neatly at a place as instructed by Railway representative at site. | Numbers 4.00 | — | 2,004.94 | 8,019.76 |
| 100 | Dismantling and releasing of existing Colour light Signals complete (upto 4 aspects) with or without Route Indicators, calling on signals, shunt signals etc., carefully without any damage to the gadgets, accounting and stacking them neatly at a place as instructed by Railway representative at site. The work i n c l u d e s b r e a k i n g t h e concrete foundation,closing t h e r e s u l t a n t p i t and resurfacing it by ramming and levelling. | Numbers 4.00 | — | 3,083.03 | 12,332.12 |
| 101 | Dismantling a n d releasing o f existing Point m a c h i n e s ( a l l t y p e s ) i n c l u d i n g ground connections a n d other accessories available complete without any damage to the gadgets, accounting a n d stacking them neatly a t a place a s instructed b y Railway representative at site. | Numbers 4.00 | — | 2,698.69 | 10,794.76 |
| 102 | "Releasing o f existing g r o u n d t y p e shunt signals along with surface base, signal post etc carefully without any damage, accounting a n d stacking t h e m n e a t l y a t a place as instructed b y Railway representative a t site. The work also includes breaking and removal o f concrete foundation a n d refilling o f the resultant pit by ramming and levelling." | Numbers 2.00 | — | 2,196.41 | 4,392.82 |
| 103 | Releasing of existing TLD boxes with stumps a n d terminals a f t e r releasing a l l t h e bond w i r e s . T h e r e l e a s e d m a t e r i a l s s h a l l be accounted and stacked neatly at a place as instructed by Railway representative at site. | Numbers 24.00 | — | 159.29 | 3,822.96 |
| Schedule total | ₹81,33,401.7 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC2022.pdf
ATTACHMENT
GCCCorrectionslip1-5.pdf
ATTACHMENT
GCCCorrectionslip6-11.pdf
ATTACHMENT
SOR2022BOOKLET.pdf
ATTACHMENT
LetterPoliceVerification.pdf
ATTACHMENT
CableCutpenaltyLetter.pdf
ATTACHMENT
ModelformofBankGuarantee.pdf Model form of Bank Guarantee
ATTACHMENT
SCOPEOFWORKANDATC.pdf
ATTACHMENT
ModelformofBankGuarantee.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .