Loading
Loading…
Loading…
Tender Value
₹10.9 Cr
EMD Value
₹10.9 L
Closing Date
21 Sept 2026, 6:00 pm
Executive Engineer’s office, Valsad (R&B) Division,
Construction Of Government Girls’ Hostel, Manekpore, Taluka Umargam, District Valsad
336251
18 of 2026-27
Open
Civil - All
Works
Valsad
19 documents required · 19 mandatory
₹18,000
Executive Engineer,Valsad (R&B) Division, Valsad
₹10.9 L
18 Aug 2026
18 Aug 2026
18 Aug 2026
21 Sept 2026
18 Aug 2026
No figures
1 Excavation for foundation upto 1.5 m depth including 4826.00 Cumt 117.08
sorting out and stacking of useful materials and
disposing off the excavated stuff upto 50 Meter lead.(A)
Loose or soft soil
2 Excavation for foundation for depth from 1.5 m to 3.0 2225.00 Cumt 162.56
m including sorting out and stacking of useful
materials and disposing off the excavated stuff upto
50 Meter lead.(B) Dense or Hard soil
3 Excavation for foundation for depth from 3.0 m to 5.0 35.00 Cumt 175.97
m including sorting out and stacking of useful
materials and disposing off the excavated stuff upto
50 Meter lead. (B) Dense or Hard soil
4 Filling in foundation and plinth with sand in layers of 20 411.00 Cumt 460.19
cm. Thickness including watering ramming and
consolidating etc. comp.
5 Filling available excavated Earth (Excluding Rock) in 1942.00 Cumt 130.39
trench plinth side of foundation . in layer not excluding
20 cm in depth consolidation each deposited layer by
ramming and watering etc. complete
soil in layer of 20 cm in thickness including ramming
watering and consolidating etc. complete
Item Rate In
Description of Item Quantity Unit Amount
No figures
7 Anti-Termite System: Providing and laying of permanent 1173.00 Sqmt 134.33
piping technology anti-termite treatment before flooring
work by installing LLDP (Low linear density
polyethylene) tube of 8 mm O.D. & 6.4 mm 1.D. with
inbuilt pressure compensation chip every 30 cm interval
in the tube, having working pressure of 2 Kg/cm2 and
release rate of 1.9 Itr/hour fixed by P-clips and nails. The
LLDP pipe shall be installed at the entire periphery of the
building and at internal network of building at a depth of
20 to 200 mm under floor at every 2 to 3 mtr. c/c
distance (adjusted as per building layout ) & Ends of loop
pass through a PVC elbow of minimum 32 mm ID at
junction box of wall and floor level, entering into a steel
reinforced grooved flexible pipe of minimum 22 mm ID
leading into junction box and the loops shall terminate in
junction boxes & test every junction during injecting
chemicals for termite control treatment. The anti termite
chemical Imidacloprid 30.5% SC mix as per IS-
6313 (part III) shall be injected by the pressure pump
diluted with water @ 10.5 ml/5 ltr of water at the rate of
2 Kg/sq.cm @ 5 Ltr/SMT. The contractor shall submit
approved line plan for piping system and junction boxes
dully approved by Engineer-in-Charge with bond of
year warranty.(i)Anti Termite chemical injected area
(Chemical injecting incl. labour cost)
8 Providing and laying cement concrete 1:3:6 (1-Cement : 292.00 Cumt 3005.76
3- coarse sand : 6- machine cut stone aggregates 40 mm
nominal size) and curing complete excluding cost of
formwork in (A) Foundation and Plinth
9 Providing and laying controlled cement concrete M150 466.00 Cumt 4101.61
for curing complete including cost of formwork but
excluding the cost of reinforcement for reinforced
concrete work in (A) Foundations, footings,Base of
columns, Plinth Slab and Mass concrete.
10 Providing and laying controlled cement concrete M250 1192.95 Cumt 4502.58
and curing complete including the cost of formwork and
excluding reinforcement for reinforced concrete work in
(A) Foundations, footings and Mass concrete.
11 Providing and laying controlled cement concrete M250 38.00 Cumt 7131.61
and curing complete including the cost of form work but
excluding the cost of reinforcement for reinforced
concrete work in Columns, pillars posts and struts
Column Up to Plinth Level
Item Rate In
Description of Item Quantity Unit Amount
No figures
12 Providing and laying controlled cement concrete M200 91.00 Cumt 7086.16
and curing complete including the cost of form work but
excluding the cost of reinforcement for reinforced
concrete work in Columns, pillars posts and struts
Ground Floor
13 Providing and laying controlled cement concrete M200 41.00 Cumt 7086.16
and curing complete including the cost of form work but
excluding the cost of reinforcement for reinforced
concrete work in Columns, pillars posts and struts First
14 Providing and laying controlled cement concrete M200 41.00 Cumt 7126.26
and curing complete including the cost of form work but
excluding the cost of reinforcement for reinforced
concrete work in Columns, pillars posts and struts
Second Floor
15 Providing and laying controlled cement concrete M200 17.00 Cumt 7166.35
and curing complete including the cost of form work but
excluding the cost of reinforcement for reinforced
concrete work in Columns, pillars posts and struts Third
16 Providing and laying controlled cement concrete M250 278.00 Cumt 6058.99
and curing complete including the cost of form work but
excluding the cost of reinforcement for reinforced
concrete work in Ground & Plinth BEAMS
17 Providing and laying controlled cement concrete M150 195.00 Cumt 5160.09
and curing complete including the cost of formwork and
excluding reinforcement for reinforced concrete work in
(C) Plinth Slabs
18 Providing and laying controlled cement concrete M200 151.00 Cumt 6022.67
and curing complete including the cost of formwork and
excluding reinforcement for reinforced concrete work in
(C) Ground Floor Beams
19 Providing and laying controlled cement concrete M200 135.00 Cumt 6022.67
and curing complete including the cost of formwork and
excluding reinforcement for reinforced concrete work in
(C) First Floor Beams
20 Providing and laying controlled cement concrete M200 135.00 Cumt 6062.77
and curing complete including the cost of formwork and
excluding reinforcement for reinforced concrete work in
(C) Second Floor Beams
21 Providing and laying controlled cement concrete M200 8.00 Cumt 6102.87
and curing complete including the cost of formwork and
excluding reinforcement for reinforced concrete work in
(C) Third Floor Beams
22 Providing and laying controlled cement concrete M200 6.00 Cumt 6331.13
and curing etc. complete including the cost of form work
and reinforcement for reinforced concrete work in (C)
Chhajja for Ground Floor
Item Rate In
Description of Item Quantity Unit Amount
No figures
23 Providing and laying controlled cement concrete M200 5.00 Cumt 6331.13
and curing etc. complete including the cost of form work
and reinforcement for reinforced concrete work in (C)
Chhajja for First Floor
24 Providing and laying controlled cement concrete M200 5.00 Cumt 6371.23
and curing etc. complete including the cost of form work
and reinforcement for reinforced concrete work in (C)
Chhajja for Second Floor
25 Providing and laying controlled cement concrete M200 1.00 Cumt 6411.32
and curing etc. complete including the cost of form work
and reinforcement for reinforced concrete work in (C)
Chhajja for Third Floor
26 Providing and laying controlled cement concrete M200 7.00 Cumt 7279.32
and curing etc. complete including the cost of form work
and reinforcement for reinforced concrete work in (C)
Lintal for Ground Floor
27 Providing and laying controlled cement concrete M200 5.00 Cumt 7279.32
and curing etc. complete including the cost of form work
and reinforcement for reinforced concrete work in (C)
Lintal for First Floor
28 Providing and laying controlled cement concrete M200 5.00 Cumt 7319.42
and curing etc. complete including the cost of form work
and reinforcement for reinforced concrete work in (C)
Lintal for Second Floor
29 Providing and laying controlled cement concrete M200 1.00 Cumt 7359.52
and curing etc. complete including the cost of form work
and reinforcement for reinforced concrete work in (C)
Lintal for Third Floor
30 Providing and laying controlled cement concrete M200 192.00 Cumt 6502.04
and curing complete including the cost of formwork and
excluding reinforcement for reinforced concrete work in
(C) Ground Floor Slab
31 Providing and laying controlled cement concrete M200 172.00 Cumt 6502.04
and curing complete including the cost of formwork and
excluding reinforcement for reinforced concrete work in
(C) First Floor Slab
32 Providing and laying controlled cement concrete M200 172.00 Cumt 6542.13
and curing complete including the cost of formwork and
excluding reinforcement for reinforced concrete work in
(C) Second Floor Slab
33 Providing and laying controlled cement concrete M200 8.00 Cumt 6582.23
and curing complete including the cost of formwork and
excluding reinforcement for reinforced concrete work in
(C) Third Floor Slab
34 Providing and laying controlled cement concrete M200 16.00 Cumt 8125.07
and curing etc. complete including the cost of form work
and excluding the cost of reinforcement etc. complete in
(E) Stair case for Ground Floor to First floor
Item Rate In
Description of Item Quantity Unit Amount
No figures
35 Providing and laying controlled cement concrete M200 10.00 Cumt 8125.07
and curing etc. complete including the cost of form work
and excluding the cost of reinforcement etc. complete in
(E) Stair case for First Floor to Second Floor
36 Providing and laying controlled cement concrete M200 10.00 Cumt 8165.17
and curing etc. complete including the cost of form work
and excluding the cost of reinforcement etc. complete in
(E) Stair case for Second Floor to Third Floor
37 Providing and laying controlled cement concrete M200 39.00 Cumt 10124.80
and curing etc. complete including the cost of form work
and excluding the cost of reinforcement etc. complete in
RCC Vertical and Horizontal wall for Ground Floor
38 Providing and laying controlled cement concrete M200 13.00 Cumt 10124.80
and curing etc. complete including the cost of form work
and excluding the cost of reinforcement etc. complete in
RCC Vertical and Horizontal wall for First Floor
39 Providing and laying controlled cement concrete M200 13.00 Cumt 10164.90
and curing etc. complete including the cost of form work
and excluding the cost of reinforcement etc. complete in
RCC Vertical and Horizontal wall for Second Floor
40 Providing and laying controlled cement concrete M200 19.00 Cumt 10205.00
and curing etc. complete including the cost of form work
and excluding the cost of reinforcement etc. complete in
RCC Vertical and Horizontal wall for Third Floor
41 Providing and laying controlled cement concrete M200 26.80 Cumt 6252.33
for RCC work and curing complete including the cost of
form work but excluding the cost of reinforced concrete
work in Coping on Ground Floor
42 Providing and laying controlled cement concrete M200 2.80 Cumt 6252.33
for RCC work and curing complete including the cost of
form work but excluding the cost of reinforced concrete
work in Coping on First Floor
43 Providing and laying controlled cement concrete M200 2.80 Cumt 6292.43
for RCC work and curing complete including the cost of
form work but excluding the cost of reinforced concrete
work in Coping on Second Floor
44 Providing and laying controlled cement concrete M200 7.20 Cumt 6332.53
for RCC work and curing complete including the cost of
form work but excluding the cost of reinforced concrete
work in Coping on Third Floor
Item Rate In
Description of Item Quantity Unit Amount
No figures
45 Providing and laying controlled cement concrete M200 4.90 Cumt 6372.62
for RCC work and curing complete including the cost of
form work but excluding the cost of reinforced concrete
work in Coping on Fourth Floor
46 Providing TMT Bar FE 550D reinforcement for R.C.C. 376574.25 Kg 95.45
work including bending, binding and placing in position
complete upto floor two level
47 Providing and fixing 90 cm Height Stainless Steel Railing 168.00 Rmt 3626.91
made from anticorrocive 304 grade S S pipe of 50 mm
dia (16 Gauge) as hand rail with S S 304 grade Baluster of
38 mm dia (16 Gauge) as a vertical support fixed in RCC
slab at 1.2m c/c including three horizontal S S pipes of
25 mm dia (16 Gauge) at eqal distance fixed by 18.75 mm
dia (16 Gauge) S S pipe with baluster including
accessories as per detailed drawing as directed etc.
48 Providing, laying and fixing 45 cm Height MS Railing 597.00 Rmt 642.36
made from anticorrocive up of RCC Perapet Wall on
fixing Hand Railing 50 mm dia (16 Gauge) MS Round
Hollow pipe horizontal 2 Nos and 35mm dia vertical
connection pipe 4 No with all material , laboure charges
and accessories as per requirement as directed by
Engineer-in-charge etc. complete.
49 Brick work using common burnt clay building bricks 235.00 Cumt 4021.02
having crushing strength not less than 35 kg./Sq.Cm. in
foundation and plinth in Cement Mortar 1:5. (1- Cement :
5 -fine sand) (B) Conventional below plinth
50 Brick work using common burnt clay building bricks 395.00 Cumt 4295.99
having crushing strength not less than 35 kg./Sq.Cm. in
foundation and plinth in Cement Mortar 1:5. (1- Cement :
5 -fine sand) (B) Conventional Ground FLoor
51 Brick work using common burnt clay building bricks 191.00 Cumt 4295.99
having crushing strength not less than 35 kg./Sq.Cm. in
super structure in Cement Mortar 1:5. (1- Cement : 5 -
fine sand) (B) Conventional First FLoor
52 Brick work using common burnt clay building bricks 191.00 Cumt 4336.49
having crushing strength not less than 35 kg./Sq.Cm. in
super structure in Cement Mortar 1:5. (1- Cement : 5 -
fine sand) (B) Conventional Second FLoor
53 Brick work using common burnt clay building bricks 50.00 Cumt 4376.98
having crushing strength not less than 35 kg./Sq.Cm. in
super structure in Cement Mortar 1:5. (1- Cement : 5 -
fine sand) (B) Conventional Third FLoor
Item Rate In
Description of Item Quantity Unit Amount
No figures
54 Half Brick masonry in common brunt clay building bricks 394.00 Sqmt 653.01
having crushing strength not less than 35 Kg/Sq.Cm. in
Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in
foundation and plinth (B) Conventional in super
structure. for Ground Floor.
55 Half Brick masonry in common brunt clay building bricks 314.00 Sqmt 653.01
having crushing strength not less than 35 Kg/Sq.Cm. in
Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in
foundation and plinth (B) Conventional in super
structure. for First Floor.
56 Half Brick masonry in common brunt clay building bricks 314.00 Sqmt 659.00
having crushing strength not less than 35 Kg/Sq.Cm. in
Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in
foundation and plinth (B) Conventional in super
structure. for Second Floor.
57 Providing and fixing 150 mm wide, approved quality 1104.00 Sqmt 295.93
chicken wire mesh at junction of brick work and RCC
work or two dissimilar surfaces, at all heights fixed by
nails, rowal plugs or tag by cement mortar 1:3 before
applying the plaster, including curing, scaffolding all
complete as directed.
58 Providing 20 mm thick double coat mala cement plaster 2510.00 Sqmt 278.54
on interior brick / concrete work for plastering
comprising of base coat of 12 mm thick cement plaster in
cement mortar (1 Cement : 4 coarse sand) in rough
finishing and 8 mm thick top coat of cement mortar 1:2
(1 Cement : 2 Coarse sand) finished with trovel including
scaffolding curing, 10x10 mm grooves etc. complete. For
Ground Floor
59 Providing 20 mm thick double coat mala cement plaster 2052.00 Sqmt 278.54
on interior brick / concrete work for plastering
comprising of base coat of 12 mm thick cement plaster in
cement mortar (1 Cement : 4 coarse sand) in rough
finishing and 8 mm thick top coat of cement mortar 1:2
(1 Cement : 2 Coarse sand) finished with trovel including
scaffolding curing, 10x10 mm grooves etc. complete. For
First Floor
60 Providing 20 mm thick double coat mala cement plaster 1970.00 Sqmt 305.26
on interior brick / concrete work for plastering
comprising of base coat of 12 mm thick cement plaster in
cement mortar (1 Cement : 4 coarse sand) in rough
finishing and 8 mm thick top coat of cement mortar 1:2
(1 Cement : 2 Coarse sand) finished with trovel including
scaffolding curing, 10x10 mm grooves etc. complete. For
Second Floor
Item Rate In
Description of Item Quantity Unit Amount
No figures
61 Providing 20 mm thick double coat mala cement plaster 432.00 Sqmt 331.99
on interior brick / concrete work for plastering
comprising of base coat of 12 mm thick cement plaster in
cement mortar (1 Cement : 4 coarse sand) in rough
finishing and 8 mm thick top coat of cement mortar 1:2
(1 Cement : 2 Coarse sand) finished with trovel including
scaffolding curing, 10x10 mm grooves etc. complete. For
Third Floor
62 Providing 10 mm. Thick cement plaster in single coat for 1408.00 Sqmt 140.95
plastering on ceiling and soffits of stairs and finished
even and smooth in : (I) Cement mortar 1:4 (1 cement :
sand) including Mala troveled finish etc. complete.
Ground Floor
63 Providing 10 mm. Thick cement plaster in single coat for 1301.00 Sqmt 140.95
plastering on ceiling and soffits of stairs and finished
even and smooth in : (I) Cement mortar 1:4 (1 cement :
sand) including Mala troveled finish etc. complete. First
64 Providing 10 mm. Thick cement plaster in single coat for 1301.00 Sqmt 164.34
plastering on ceiling and soffits of stairs and finished
even and smooth in : (I) Cement mortar 1:4 (1 cement :
sand) including Mala troveled finish etc. complete.
Second Floor
65 Providing 10 mm. Thick cement plaster in single coat for 59.00 Sqmt 187.73
plastering on ceiling and soffits of stairs and finished
even and smooth in : (I) Cement mortar 1:4 (1 cement :
sand) including Mala troveled finish etc. complete. Third
66 20 mm thick Sand faced cement plaster with 10x10 mm 5524.00 Sqmt 352.49
grooves as suggested by this office consisting of 12 mm
thick backing coat of C.M. 1:3 ( 1 cement : 3 coarse sand )
and 8 mm thick finishing coat of C.M. 1:1 ( 1 cement :
coarse sand) for all heights as directed etc. complete.
and as per pattern sample aprroved by the architect or
directed engineer in-charge
67 Providing throating or plaster drip and moulding to 278.00 Rmt 42.17
R.C.C. Chhajja.
Item Rate In
Description of Item Quantity Unit Amount
No figures
68 Providing and fixing eco-friendly light weight calcium 110.00 Sqmt 1648.96
silicate false ceiling tiles having Tegular edge & 15 mm
Thick Densified edges on the Tile Periphery for Extra
Strength The Light weight calcium silicate ceiling tiles
shall have, light reflection 85% non-combustible as per
B.S. 476 part IV, 100% humidity resistance and also
having thermal conductivity0.043° w/m KC.for the best
thermal Insulation. The Light weight calcium Silicate tile
shall be of approved texture Fine fissured/ Spintone/
Cosmos having NRC value of 0.5 & Globe having NRC
value of 0.75 NRC or equivalent of size 595 X 595 mm to
be laid on true horizontal level suspended inter locking
metal grid of hot dipped galvanized steel sections
(galvanizing @120 grams per sqm including both side)
consisting of main ‘T’ runner suitably spaced at joints to
get required length and size of 24 X 38mm made from
0.30 mm thick (minimum) sheet, 1200mm centre to
centre, and cross ‘T’ of size 24 X 28mm made out of
0.33mm (Minimum) sheet spaced 1200mm along spaced
between main 'T' at 600mm centre to centre to form
agrid of 1200x600mm and size 24x48mm made of
0.30mm thick (Minimum) sheet to be interlocked at
middle of the 1200x600mm panel to form grid of size
600x600mm resting on periphery walls/partitions on a
perimeter wall angle pre-coated steel of size
(24x24x3000mm made of 0.40mm thick (minimum)
sheet with the help of rawl plugs at 450mm centre to
centre with 25mm long dry wall screws @ 230mm
interval and laying 15mm thick densified edges light
69 Applying two coats of Acrylic lapy (putty) & two coats of 10797.00 Sqmt 40.59
primer of approved brand and manufacture on new wall
surface to give an even shade including thoroughly
brushing the surface free from mortar dropping and
other foreign matter and sand papered smooth.
70 Wall painting (two coats) with plastic emulsion paint of 6732.00 Sqmt 80.35
approved brand and manufacture on undecorated wall
surface to give an even shade including throughly
brushing the surface free from mortar droppings and
other foreign matter and sand papered smooth.
71 Painting (two coats) with plastic emulsion paint of 4065.00 Sqmt 85.76
approved brand and manufacture on undecorated ceiling
surface to give an even shade including throughly
brushing the surface free from mortar droppings and
other foreign matter and sand papered smooth.
Item Rate In
Description of Item Quantity Unit Amount
No figures
72 Wall Painting (Two coats) with weather proof acraylic 5518.00 Sqmt 114.53
emulsion paint of approved brand and manufacture and
of required shade on exterior wall surface to give an even
shade over and including primery coat with Alkaly
resistance primer of approved brand after thoroughly
brushing surface to remove all dust and remains of
loose powdered material etc. copm. for all height
73 Providing And filling with good quality cinder (steam 41.00 Cumt 519.14
coal) as directed by engineer in charge in sunks in layers
of 15 cm thick,including watering,placing ,ramming well
etc as directed, for all floor.
74 Providing Water proofing Treatment on Sunk Slab 200.00 Sqmt 341.38
including cement concrete flooring 1:2:4 (1-cement : 2-
coarse sand : 4-graded stone aggregate 20mm nominal
size) laid in one layer and finished with a floating coat of
neat cement average 50mm thick to Prepare slope
including water proofing chemical etc. Complete for
Sunk Slab All Floor.
75 Providing and laying water proofing treatment with 1203.00 Sqmt 1099.89
china mosaic tiles flooring over avg 50 mm C.C. 1:2:4
bedding for maintaining slope for plain and curve surface
& 12 mm to 20 mm of broken piece not more than 2.5CM
of ceramic / glazed tiles ( one for more colour as directed
) to be laid over cement mortar bedding of C M 1:3 (1
cement : 3 sand ) contain water proofing materials per
bag of cement useas specified by manufactured and slops
to be tempered to bring mortar up to surface with using
white cement and colour pigment including rounding of
junctions and extending them up to 15 cm along the wall
and curing with bends any patens or design as per
drawing and cleaning by using oxalic acid etc. complete.
Item Rate In
Description of Item Quantity Unit Amount
No figures
76 Providing Plinth Protection to Building including 236.00 Sqmt 1398.85
excavation in ordinary soil and laying cement concrete
1:3:6 using stone aggregates of 40mm nominal size in
foundation layer 100 mm thick below pre-cast Rubber
Dye inter locking concrete block 60mm thick with grade
of concrete M200 pneumatic compressed by
mechanically pressed and as per approved design
including 75mm Sand layer for levelling and filling the
joint with sand in proper line and level etc. complete,
Including Providing and fixing pre-cast concrete kerb
stone of grey cement based concrete block 30cm length,
30cm height and 15cm thick of M250 grade concrete as
per approved design and including excavation for fixing
in proper line and level, filling the joint with C:M 1:3
(1cement:3 fine sand) etc. complete.
77 Providing and fixing 3 shutter 3 track window having 141.00 Sqmt 3305.73
extruded aluminum Colour anodized section frame main
outer size 95mm x 24.10mm x 1.17mm @ wt.of
Kg/mt , horizontal two track member size 92mm x
31.75mm x 1.50mm,@ Wt.1.07 Kg/mt , vertical member
of size 92mm x 31.75mm x 1.50mm @ Wt. 1.07 Kg/mt
with sliding shutters of horizontal member size
mmx18mm x1.29mm @ wt.of 0.547 Kg/mt, vertical
member of size 40mm x 18mm x 1.29 mm @ wt.of
0.547Kg/mt, Beading clip 19mmx 17.30mmx0.90mm @
wt. of 0.124 Kg/mt with 5 mm thick transparent bronze
colour tinted float glass with powder coated aluminum
fittings and fixtures and transparent silicon sealant glass
fixing to frame as per details etc
78 Providing and fixing 2 shutter 2 track window having 83.00 Sqmt 3098.68
extruded aluminum Colour anodized section frame main
outer size 95mm x 24.10mm x 1.17mm @ wt.of
Kg/mt , horizontal two track member size 92mm x
31.75mm x 1.50mm,@ Wt.1.07 Kg/mt , vertical member
of size 92mm x 31.75mm x 1.50mm @ Wt. 1.07 Kg/mt
with sliding shutters of horizontal member size
mmx18mm x1.29mm @ wt.of 0.547 Kg/mt, vertical
member of size 40mm x 18mm x 1.29 mm @ wt.of
0.547Kg/mt, Beading clip 19mmx 17.30mmx0.90mm @
wt. of 0.124 Kg/mt with 5 mm thick transparent bronze
colour tinted float glass with powder coated aluminum
fittings and fixtures and transparent silicon sealant glass
fixing to frame as per details etc
Item Rate In
Description of Item Quantity Unit Amount
No figures
79 Providing and fixing 4 shutter 2 track window having 16.00 Sqmt 2900.72
extruded aluminum Colour anodized section frame main
outer size 95mm x 24.10mm x 1.17mm @ wt.of
Kg/mt , horizontal two track member size 92mm x
31.75mm x 1.50mm,@ Wt.1.07 Kg/mt , vertical member
of size 92mm x 31.75mm x 1.50mm @ Wt. 1.07 Kg/mt
with sliding shutters of horizontal member size
mmx18mm x1.29mm @ wt.of 0.547 Kg/mt, vertical
member of size 40mm x 18mm x 1.29 mm @ wt.of
0.547Kg/mt, Beading clip 19mmx 17.30mmx0.90mm @
wt. of 0.124 Kg/mt with 5 mm thick transparent bronze
colour tinted float glass with powder coated aluminum
fittings and fixtures and transparent silicon sealant glass
fixing to frame as per details etc
80 Providing & Fixing in position standard extruded 36.00 Sqmt 2724.98
approved colour anodised Aluminum Ventilation with
outer frame 65 x 25 x 1.50 mm Stander Box Frame @ Wt
0.833 kg/Rmt with 5mm thick fixed ground glass and
Mosquito net jali fixed to alluminium strip blade fixed or
adjestable ventilation including all required materials,
fixtures, fastenning, labours and equipments as per
detailed drawing as directed. For Ventilators
81 Providing and fixing Double shuttered door having green 14.70 Sqmt 5201.50
marble frame with all open edges machine cut &
machine polished, fixed by zinc coated hinges with
double shutter of factory made & stamped I.S
grade one, type one 35 mm thick solid core, melamine
faced, three layered resin, flushed door , having
decorative lamination on both sides & 12 mm thick teak
wood beading fixed around the door, Durable Grip shall
be providing with both side 15cm long stainless steel
handle and necessary Locking system, S.S. fixtures &
fastenings etc. directed by engineer in charge.
82 Providing and fixing Single shuttered door having green 95.00 Sqmt 3524.90
marble frame with all open edges machine cut &
machine polished, fixed by zinc coated hinges with
double shutter of factory made & stamped I.S
grade one, type one 35 mm thick solid core, melamine
faced, three layered resin, flushed door , having
decorative lamination on both sides & 12 mm thick teak
wood beading fixed around the door, Durable Grip shall
be providing with both side 15cm long stainless steel
handle and necessary Locking system, S.S. fixtures &
fastenings etc. directed by engineer in charge.
Item Rate In
Description of Item Quantity Unit Amount
No figures
83 Providing and fixing FRP frame size 100 x 50 mm and 35 154.00 Sqmt 2363.40
mm thick ( Fiber Glass with PUF Injection ) FRP depress
panel Single or Double shutter having extra
reinforcement on sides & edges in Gel coat finish.The
core of the both shutter & frame is to be filed up with
injected fire retradat grade polyurethene foam done in
situ along with embeded wooden pieces for stiffening &
also taking hinges & fintures.The whole FRP frame &
single or double shutter is to be waterproof,
weatherproof, termite proof & resistance to mild
acid/alkali. Rates are to be inclusive of S.S hinges with
necessary screws & alluminum fixtures & fastenings &
fartener sleeve.Colour and Shade approved by Engineer-
In-Charge.
84 Providing and laying 60 x 60 cm Machine polished 2648.00 Sqmt 1029.22
Machine cut Blue Kota Stone slab flooring over 20 mm
(average)thick base of cement mortar 1:6 (1-cement 6-
coarse sand) or L.M 1:1.5 (1 Lime putty : 1.5 coarse sand
laid over and jointed with grey cement slurry mixed with
pigment to match the shade of slab including rubbing and
polishing etc.complete (A) 30mm thick
85 Providing and laying 60 x 60 cm Machine polished Blue 146.00 Sqmt 1089.67
Kota Stone slab 30 mm thick in riser of steps,skirting
dedo and pillars laid on 10 mm thick cement mortar 1:3
(1-cement 3-coarse sand) and jointed with grey cement
slurry mixed with pigment to match the shade of slab
including rubbing and polishing etc.complete (30 mm
86 Providing and laying Matt finished ceramic tiles 60 x 60 185.00 Sqmt 1463.49
cm size 6 mm thick in flooring treads of steps and
landing laid on a bed of 12 mm thick cement mortar
1:3(1-cement:3-coarse sand)finishing with flush pointing
in white cement
87 Providing and laying antiskid ceramic tiles 30 x 30 cm 365.50 Sqmt 970.07
size 6 mm thick in flooring treads of steps and landing
laid on a bed of 12 mm thick cement mortar 1:3(1-
cement:3-coarse sand)finishing with flush pointing in
white cement
88 Providing and laying coloured glazed tiles of the size 300 1300.00 Sqmt 1441.22
skirting, risers of steps and dedo on 10 mm. thick cement
plaster 1:3 (1 cement : 3 coarse sand) & jointed with
white cement slurry.
Item Rate In
Description of Item Quantity Unit Amount
No figures
89 Providing and laying machine cut free edge machine 171.00 Sqmt 2018.99
polished granite stone 18mm thick finished treads and
risers in with 1cm projecting, nozing rounded moulding
in tread laid over 12 mm (av.) thick bases of cement
mortar 1:6 (1-cement : 6-coarse sand) jointed with grey
or colour cement slurry including rubbing and polishing
incl. making Three No.s of grooves of size 3mm X 3mm
along the length of treads etc. complete
90 Providing and fixing polished 18 mm thick black granite 1.00 Sqmt 2651.25
with full round edge and double side polished of
approved quality in between urinal and fixing with
cement slurry & adhesive including moulding of both
exposed edges as directed by engineering in charge etc.
91 Providing and fixing mirror polished 18 mm thick Green 498.00 Sqmt 2004.85
Marble stone with full round edge and polished of
approved quality in clading on sill and around the doors/
windows/ ventilation with 12 mm thick cement mortor
CM (1:4) and fixing with cement slurry & adhesive
including moulding of exposed edges as directed by
engineering in charge etc. complete.
92 Providing and fixing pre-cast Rubber Dye / steel Dye 1207.00 Sqmt 686.90
inter locking concrete block 60mm thick with grade of
concrete M300 pnumatic compressed / vibrated
mechanically and as per approved design Confirming to
IS 15658 : 2006 including 35 mm Sand layer for levelling
and filling the joint with sand in proper line and level as
per guidlines of IRC : SP 63-2018 etc. Complete
93 Providinfg and fixing Safty grills of required pattern for 8496.00 Kg 99.99
windows/ Door using necessary 16x16 mm M.S. Square
bar, M.S flats and other structural steel at required
spacing including cutting, welding and fabriction etc.
including one coat of primer of approved quality and two
coats of oil painting as per detail drawing etc complete.
94 Providing erecting and fixing double coated Syntex PVC. 20000.00 Litre 3.95
(ISI) water tank of required capacity each with all
necessary fittings and connection etc. complete on
95 Providing laying and jointing in true line and level 50mm 280.00 Rmt 195.67
dia. U.P.V.C. Pipe ( SCH- 40) for cold water including
fittings as approved by Engineer In Charge. Pipe shall be
fixed on the wall with the help of clamp at every two
metre C/C or shall be concelled as directed including
necessary fittings etc. including testing of pipe and joints
and fixing the same with adhesive solvent, including cost
of all materials.
Item Rate In
Description of Item Quantity Unit Amount
No figures
96 Providing laying and jointing in true line and level 40mm 200.00 Rmt 148.12
dia. U.P.V.C. Pipe ( SCH- 40) for cold water including
fittings as approved by Engineer In Charge. Pipe shall be
fixed on the wall with the help of clamp at every two
metre C/C or shall be concelled as directed including
necessary fittings etc. including testing of pipe and joints
and fixing the same with adhesive solvent, including cost
of all materials.
97 Providing laying and jointing in true line and level 25mm 255.00 Rmt 91.84
dia. U.P.V.C. Pipe ( SCH- 40) for cold water including
fittings as approved by Engineer In Charge. Pipe shall be
fixed on the wall with the help of clamp at every two
metre C/C or shall be concelled as directed including
necessary fittings etc. including testing of pipe and joints
and fixing the same with adhesive solvent, including cost
of all materials.
98 Providing laying and jointing in true line and level 15mm 225.00 Rmt 72.65
dia. U.P.V.C. Pipe ( SCH- 40) for cold water including
fittings as approved by Engineer In Charge. Pipe shall be
fixed on the wall with the help of clamp at every two
metre C/C or shall be concelled as directed including
necessary fittings etc. including testing of pipe and joints
and fixing the same with adhesive solvent, including cost
of all materials.
99 Providing, laying and jointing in true line and level 160 105.00 Rmt 831.22
diametre U.P.V.C (Type B) conforming to IS 13592-1992
with one end plain and other end socketed with rubber
ring, & fittings conforming to ISI 14735-1999 of
approved make for drainage system pipe line, pipe shall
be jointed with each other with rubber lubricant, pipe
shall be fixed on wall using of PVC clamp of the size
mm diametre x 210 mm length x 196 mm heigh at every
2000 mm center to center or shall be concealed in walls
as directed including necessary fittings such as bends,
shoes etc. including testing of pipes and joints and
jointed with adhesive solvent cement including cost of all
materials.
Item Rate In
Description of Item Quantity Unit Amount
No figures
100 Providing, laying and jointing in true line and level 110 695.60 Rmt 836.73
diametre U.P.V.C (Type B) conforming to IS 13592-1992
with one end plain and other end socketed with rubber
ring, & fittings conforming to ISI 14735-1999 of
approved make for drainage system pipe line, pipe shall
be jointed with each other with rubber lubricant, pipe
shall be fixed on wall using of PVC clamp of the size
mm diametre x 149 mm length x 145 mm heigh at every
2000 mm center to center or shall be concealed in walls
as directed including necessary fittings such as bends,
shoes etc. including testing of pipes and joints and
jointed with adhesive solvent cement including cost of all
materials.
101 Providing, laying and jointing in true line and level 75 60.00 Rmt 293.91
mm dia. UPVC SWRType B pipe conforming to IS 13592-
1992 with one end plain and other end socketed with
rubbering and fitting conforming to ISI 14735-1999 of
approved make for drainage system pipe line, pipe shall
be jointed with each other with rubber lubricant, pipe
shall be fixed on wall using of PVC clamp at every
mm c/c or shall be conceled in walss as directed
including necessary fittings such as bends, shoes etc.
including testing of pipes and joints and jointed with
adhesive solvent cement including cost of all materials.
102 Providing and fixing in PVC SWR cowel went 75mm dia 4.00 No 16.16
to pipes.(B) 75mm dia.
103 Providing and fixing in PVC SWR cowel went 110mm dia 22.00 No 29.29
to pipes.(B) 110mm dia.
104 Providing and fixing PVC SWR Nahni trap IS 14735 for 105.00 No 571.08
drain - 100 mm diameter with jali of the following
nominal diameter of self cleansing design with C.I scread
down or hinged grating including the cost of cutting and
making good the walls.
Item Rate In
Description of Item Quantity Unit Amount
No figures
105 Providing and fixing wash down water closet (European 41.00 No 3001.72
type W C pan) with integral P and S trap including
jointing the trap with soil pipe in cement mortar 1:1 (1
cement five sand) including providing and fixing plastic
seat cover for wash down WC with CP brass hinges and
rubber buffers back plastic seat and including providing
and fixing PVC flushing tank with a pair of C I or MS
bracket with complete fitting such as lead valve siphon
15 mm dia brass ball valve with polythene float CP brass
handle unions and couplings for connection with inlet
out let and over flow pipes 40 mm dia porcelain
enameled flush bend including cutting holes in walls and
making good the same connection the flush bend with
cistern and closet vitreous china.
106 Providing and fixing stainless steel grab 22 cm x 60 cm 2.00 No 1492.78
for handicapped toilet
107 Providing and fixing brass screw down stop tap.(A) 82.00 No 205.83
108 Providing and fixing ball cock of approved. quality as 4.00 No 189.84
directed.(A) Copper Metal (ii) 50mm dia.
109 Providing and fixing washbasin with single hole for pillar 29.00 No 1670.26
tap with C.I. or M.S. brackets painted white including
Rubber plug, sutting holes and making good the same but
excluding fittings and also including rate of C.P. brass
waste for washbasin or sink (A) 32mm dia. and M.I.
fisher union for washbasin or sink. (A) 32mm dia.; (A)
Vitreous China:(ii) Flat Back washbasin 550 mm x v
400mm size. (i) In white colour.
110 Providing and fixing 600mm x 450mm bevelled edge 25.00 No 833.73
mirrror of superior glass mounted on 6mm thick A.C.
sheet or plywood sheet and fixing to wooden pluge with
C.P. brass screws and washers.
111 Providing and fixing C.P. brass towel rail comlete with 40.00 No 603.19
C.P. brass brackets fixed to wooden plugs with C.P. brass
scews (B) 600mm x 20mm size.
112 Providing and fixing screw down bib taps of following 156.00 No 214.81
size.(A) Brass screw down bib tap polished bright. (i)
113 Providing and fixing pillar tap, capstan head, screw down 29.00 No 308.73
high pressure with screws, shanks and back nuts. (i)
114 Providing and fixing chromium plated brass half trun 41.00 No 263.77
flush cock of approved quality including fixing in pipe
line etc. complete (ii) 25mm dia.
Item Rate In
Description of Item Quantity Unit Amount
No figures
115 Providing laying (to level or slopes) and jointing 380.00 Rmt 665.48
reinforced concrete Light duty non-pressure pipes I.S.
class NP2 of the following internal diameter with collars
and butt ends prepared for collar joints including testing
of joints complete. (D)
116 Providing and laying (two level or slopes) and jointing 300.00 Rmt 518.84
with stiff mixture of Cement Mortar in proportion 1:1,
Salt glazed stone ware pipes of pipes 150mm laying lime
concrete 1:2:4 (1-Lime putty :2-Fine samd : 4-Graded
brick aggregates 40mm nominal size) bedding for
stoneware pipes of following internal diameters with
necessary formwork and curing complete.
117 Providing and fixing S.W. gully trap with C.I. grating brick 14.00 No 1246.92
masonry chamber and water tight C.I. cover with frame
of 300mm x 300mm size (inside) with standard weight
(i) Square mouth traps (B) 150mm x 100mm size P or R
118 Constructing brick masonry chamber for underground 30.00 No 3223.92
C.I. Inspection chamber and bends with briocks having
croshing strength not less than 35Kg. Cm2 in C.M. 1:5
precast RCC cover 455mm x 610mm intenal dimensions
with frame (R.C.C. top slabe with 1:2:4 mix (1-cement :2-
coarse sand :4-graded stone aggregate 20mm size)
foundation concrete 1:5:10 inside plaster 15mm thick
with cement mortar 1:3 finished smooth with a floating
coat of neat cement on walls and bed concrete etc.
complete (i) Inside dimensions 455mmx 610mm and
450mm deep for single pipe line.
119 Constructing brick masonry chamber for underground 30.00 No 3933.95
C.I. Inspection C.I. Inspection chamber and bends with
briocks having croshing strength not less than 35Kg. Cm2
in C.M. 1:5 precast RCC cover 500mmx 700mm intenal
dimensions with frame (R.C.C. top slabe with 1:2:4 mix (1-
cement :2- coarse sand :4-graded stone aggregate 20mm
size) foundation concrete 1:5:10 inside plaster 15mm
thick with cement mortar 1:3 finished smooth with a
floating coat of neat cement on walls and bed concrete
etc. complete (i) Inside dimensions 500mmx 700mm and
450mm deep for single pipe line.
Item Rate In
Description of Item Quantity Unit Amount
No figures
120 Constructing brick masonry chamber for underground 20.00 Each 242.39
C.I. Inspection chamber and bends with briocks having
croshing strength not less than 35Kg. Cm2 in C.M. 1:5
precast RCC cover 455mm x 610mm intenal dimensions
with frame (R.C.C. top slabe with 1:2:4 mix (1-cement :2-
coarse sand :4-graded stone aggregate 20mm size)
foundation concrete 1:5:10 inside plaster 15mm thick
with cement mortar 1:3 finished smooth with a floating
coat of neat cement on walls and bed concrete etc.
complete (i) Inside dimensions 455mmx 610mm and
450mm deep for single pipe line.
Extra over items for every additional depth of 0.1M. of
part thereof beyond 450mm depth for Brick masonry
chamber.(i) for 455mm x 610mm size.
121 Constructing brick masonry chamber for underground 20.00 Each 264.86
C.I. Inspection C.I. Inspection chamber and bends with
briocks having croshing strength not less than 35Kg. Cm2
in C.M. 1:5 precast RCC cover 500mmx 700mm intenal
dimensions with frame (R.C.C. top slabe with 1:2:4 mix (1-
cement :2- coarse sand :4-graded stone aggregate 20mm
size) foundation concrete 1:5:10 inside plaster 15mm
thick with cement mortar 1:3 finished smooth with a
floating coat of neat cement on walls and bed concrete
etc. complete (i) Inside dimensions 500mmx 700mm and
450mm deep for single pipe line.
Extra over items for every additional depth of 0.1M. of
part thereof beyond 450mm depth for Brick masonry
chamber.(i) for 500mm x 700mm size.
122 Providing and fixing GI Ladder of required pattern with 600.00 Kg 94.94
GI flats(30x3mm) or round or square bars (12mm) at
required spacing & with round headed bolts and nuts or
screws or welding including primer coat of approved
quality and two coats of oil paintas as directed by
engineer in charge
123 Constructing Kitchen Platform of 18 mm thick Polished 11.00 Sqmt 4193.52
Black Granite at top and 25 mm thick Kota stone slab
one side polished at bottom with cementing Materials /
adhsives including makeing necessary grooves in walls
with Vertical sandwich two Kotastone 25 mm support
every 60 cm centre to centre or as required including all
labour material of approved quality incl. full moulded
round front edge granite strip of one side polished and
jointed with grey cement slurry including rubbing and
polishing etc. complete for all floors
Item Rate In
Description of Item Quantity Unit Amount
No figures
124 Providing and fixing 25 mm thick polished kota stone 23.00 Sqmt 667.61
Shalve with full round edge and double side polished of
any required and fixing with cement slurry & adhesive
including both exposed edges cut and Smooth Finished
as directed by engineering in charge etc. complete.
125 Providing and fixing Kitchen sink with C.I. or M.S. 3.00 No 3586.51
brackets, painted white including cutting holes in walls
and making good the same but excluding fittings. (C)
Vitreous China Sink.(i) 600mm x 450mm x 150mm size
126 Providing and fixing Kitchen platform trolley having 11.00 Sqmt 12664.39
three drawers of SS (IS 304) of required size like thali,
katleri, perforated, partition, cupsosar type in kitchen
platform having drawer front side and backside by using
19mm thick all proof plywood of ISI quality all side
laminated etc. as directed. The size of SS (IS 304) basket
of size 4" to 18" for thali, dish, katleri, perforated,
partition, cupsosar type as directed including necessary
S.S. fittings, handles, nobs, telescopic channels, etc. as
127 Providing and fixing 0.75 meter wide sand which type 16.00 Sqmt 7232.61
counter platform including supplying and fixing granite
stone of Z black or equivalant quality 18 mm thick
mirror polished on top and side posiition and vertical
strip at front with cement slurry & adhesive including
moulding of both exposed edges over 25 mm thick
kotah stone platform fixing in top and sides and
itermediates supports fixing with cement mortar and
adhesive and finishing all material and labour and
assessories and 3 no flat back wash with necessary fitting
MI Fisher , Waste pipe and coupling , 15 mm pillar cock
etc. complete etc.
128 Providing and fixing 0.45 meter wide sand which type 49.00 Sqmt 3413.80
platform including supplying and fixing granite stone of
Z black or equivalant quality 18 mm thick mirror
polished on top and side posiition and vertical strip at
front with cement slurry & adhesive including moulding
of both exposed edges over 25 mm thick kotah stone
platform fixing in top and sides and itermediates
supports fixing with cement mortar and adhesive and
finishing all material and labour complete etc.
129 Providing and fixing in position 300 mm high, 150 mm 100.00 No 707.00
wide English letters made from 1.0 mm thick stainless
steel sheet as directed by Engineer in charge with all
necessary tools & plants etc. complete.
Item Rate In
Description of Item Quantity Unit Amount
No figures
130 Providing and fixing in position 150 mm high, English 150.00 No 404.00
letters made from 1.0 mm thick stainless steel sheet as
directed by Engineer in charge with all necessary tools &
plants etc. complete.
131 Providing and laying and fixing 50 mm thick expansion 78.00 Sqmt 1491.03
joint by hydro cell semi rigid UV resistance with high
performance laminated closed cell polythene foam joint
filler in sheet foam as directed, etc. complete.
132 Applying and providing Expansion joint sealing System 78.00 Sqmt 4772.00
on 100 mm vide joint including cleaning of exansion joint
by mechanical means provision of adhesive and flexible
membrane with required bond length as per
menufracturer specification and 4mm thick alluminium
strip covering with one side sloted and bolted with
suitable system, inclusive of all manpower, machinery
and material as per specification and as directed.
133 Providing and filling the expansion joint by Thioflex 600 78.00 Sqmt 515.39
polymer or equivalent confirm to BS 4254-1983 as per
required shade and manufactured specifi-cation by
making groove of 50 mm x 12.5 mm lather by cutting or
by repairing groove and removing mortar drop or any
other foreign materials including applying primer and
filling required size (oversize of joint PU foam etc.
134 Providing and fixing 25 cm Wide & 3mm thick exterior 78.00 Sqmt 1054.34
composite panel on existing expansion joint horizontally
& vertically with all material, hardware, acessories &
fittings etc completed.
135 Providing & Fixing 114mm wide G.I. Sheets lovers having 169.00 Sqmt 4537.93
weight not less than 490 Gm/m roll formed to create
84mm wide louver snap fixed on special shaped GI
channel. Fix louvers & channels shall finished with
powder coating of 55 micron (1) 0.55mm thick sheet.etc.
complet as per detail drawing as directed.
136 Providing and fixing coloured self adhesive PU-Tactile 18.00 Sqmt 5540.86
tile, ground surface indicators of Polyurethane) of size
300mm x 300mm for guiding/warning to the visually
visitors in the centre/side of the pedestrian/approach
pathway as per specification and guidelines complete in
all respect to the entire satisfaction of in charge.
Item Rate In
Description of Item Quantity Unit Amount
No figures
137 Providing and fixing acrylic multilingual Braille (raised 20.00 Nos 2041.72
dots) DIRECTIONAL SIGNBOARDS of size 225 x 150mm
designed as per accessibility standards and having
3.5mm thick acrylic base plate with Upper Case San Serif
words made of white acrylic non glare cut out letters of
height 15mm raised not less than 0.8mm above base
plate and the equivalent word written in Hindi with
Devanagari non glare acrylic letters of height 15mm
raised not less than 0.8mm above base plate and having a
non-glare acrylic cut arrow pointing in the required
direction. Each signboard to be fixed as per
manufacturers specifications on the wall at the approved
location and at a height of 1200mm from FFL complete
as per design / specifications and guidelines as per the
entire satisfaction of the Engineer-in-charge
138 Providing & Fixing Braile Indicator Of Size 170 Mm X 30.00 Rmt 1093.83
35mm For Handrails Of The Approved Design And Make
Have Braile Dots Raised 0.5 Mm Above Base Plate To Be
Installed At Specific Locations As Per Direction Of
Engineer In Charge
139 Providing and fixing of conspectus tape 50mm width on 35.00 Rmt 2557.83
of treads in staircase including cutting pasting etc. As per
harmonised guidelines complete in all respect to the
entire satisfaction of engineer in charge.
140 Providing and fixing to wall ceiling and floor 10.0 Kg. 280.00 Rmt 336.24
F/Cm2 working pressure poluthene pipes of the
following outside Dia. Low densidy, complete with
special falnge compression type fittings, wall clipsetc.
including making good the wall ceiling and floor.(G)110
141 Providing and fixing to wall ceiling and floor 10.0 Kg. 40.00 Rmt 696.90
F/Cm2 working pressure poluthene pipes of the
following outside Dia. Low densidy, complete with
special falnge compression type fittings, wall clipsetc.
including making good the wall ceiling and floor.(G)160
142 Providing junction for rain water juncton chamber of size 14.00 No 8603.18
0.60x0.60x0.75m with excavation of size 1.96x1.96 m &
0.15m thick c.c.1:2:4 bed concrete including brick
masonary wall in CM 1:6 of 0.75m height & 0.23m thick
with 15mm thick cement plaster inside & outside &
1.06x1.06 RCC (1:2:4) slab of thickness 0.15m with CRS
steel and 0.60mx0.45m cast iron manhole cover with
frame weight not less than 35 kg as per directed by
Engineer-in-charge
Item Rate In
Description of Item Quantity Unit Amount
No figures
143 Providing Filter chamber of Brick work in C:M 1:6 of size 2.00 No 15477.24
2.06mx1.20m x1.20m & excavation dimension of 2.66mx
1.81x1.35m including C.C 1:2:4 bed concrete of 0.15m
thick including brick work in c.m 1:6 for 23cm thick wall
including 15mm thick cement plaster inside & outside
with cement slurry & 10cm thick RCC 1:2:4 top cover
with frame of minimum weight of 35 kg & filling filter
material kapchi in layers (25-40mm & 10-20mm) & BT
metal 40mm & sand as per directed by Engineer-in-
144 Providing Recharging pit of size 2.0m Dia.& 2.0m depth 1.00 No 13913.76
of water logging with excavation filling the pit with
gravel & sand in layers including making 300mm dia
bore depth of 4.5mt & above concrete with kapchi in
layers (25-40mm & 10-20mm) & BT metal 40mm &
filling brick as directed by Engineer-in-charge.
145 Providing and laying cement concrete 1:2:4 (1- Cement : 105.00 Cumt 3683.34
2- Coarse sand : 4- graded stone aggregates 20 mm
nominal size) and curing complete excluding cost of
formwork in (A) Foundation and Plinth
146 Constructing brick masonry chamber for underground 10.00 No. 7180.44
C.I. Inspection chamber and bends with briocks having
croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I.
cover with frame (Light duty) 455mm x 610mm intenal
dimensions, total weight of cover with frame to be not
less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame
15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2-
coarse sand :4-graded stone aggregate 20mm size)
foundation concrete 1:5:10 inside plaster 15mm thick
with cement mortar 1:3 finished smooth with a floating
coat of neat cement on walls and bed concrete etc.
complete.(iii) Inside dimensions 600mm x 850 mm and
450mm deep for pipe lines with three or more inlets.
147 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. 2.00 Nos 958.17
size having weight not less than 35Kg.
148 Providing & erecting open well horizontal mono block 2.00 Nos 36107.50
pump set with cast iron body, complete for three phase
submersible motor having
[H]For 15 H.P,3 phase open well horizontal mono block
pump set suitable for 1600 LPM to 1025 LPM @ 33 to
MTR head suitable for 65/80 mm dia delivery pipe
Item Rate In
Description of Item Quantity Unit Amount
No figures
149 Supplying & erecting approvedmake 3 phase motor 2.00 Nos 19695.00
control cubicalpanel (Star-Delta) made from 16G.CRCA
sheet duty painted with epoxy powder painted inside
and outside with hinged doors and locking arrangement,
consisting suitable size of ON-OFF isolator (AC-
3/23duty) main fuses,single phasing preventer cum
water level, Guard(Compe unit), Toggle switch to by pass
Single phase preventercum WLG,indicating lamps forR-Y-
Bphases, over load relay.Automatic water level
controller, Ammeter &Voltmeter each with two way
Crimped,Panel to be erected on angle iron frame grouted
on wall as overload relay,thermal/Electronics star delta
cutoff timer,start-stop push buttons.The isolator
overload relay &cntractors ofL&T,Siemens or Cuttler
Hamer make only.Panel to be erected on angle iron frame
ground on wall (e)S/D upto 2.5 H.P.
150 Providing and fixing rolling shutters of approved make 10.00 Sqmt 3503.41
made of 80 mm wide M.S laths inter-locked together
through heir entire length and jointed together at the
ends by end locks mounted on specially designed pipe
shaft with bracket plates,guide channels and
arrangement for inside and outside locking with push-
pull operation including the cost of hood cover and sprig
etc.complete(A) Shutters having width below 3.5M
151 Drilling of 165 mm dia bare in over burden strata and 130.00 Rmt 196.95
further drilling of 165mm dia bore in all typs of strata
with DTH ring including lowering of casing pipe up to
requied length and testing etc. including testing with ben
152 Providing and lowering of 165mm FVPVC pipe zero to 100.00 Rmt 536.57
overburden strata
153 Providing and lowering 165 mm dia PVC pipe etc 30.00 Rmt 252.50
154 Providing and fixing M. S. cap –plug hinge type with 2.00 No. 165.64
frame of required design for 150mm dia Bore casing
155 Suppling and installing submersible pumping set 7.50 HP 4.00 Set 26300.40
manufactured as per IS standard including non return
valve sluice valve flexible cable ( asrequired 70 mtr
length ) volt meter, panel board, capacitor,starter,switch,
pressure guage with accessories of approved
manufacture tools of 50 Hours power capacity.
156 Providing and fixing check or non return pully wheel 4.00 No. 1111.00
valve of 50 mm diameter.
Item Rate In
Description of Item Quantity Unit Amount
No figures
157 Providing and fixing to wall,ceiliing and floor galvanised 130.00 Rmt 787.40
mild steel tubes ( Medium grade ) of the following
nominal bore, tube, fittings and clamps included making
good the wall, ceilling and floor (F) 50 mm
158 Box cutting the road surface to proper slope and camber 771.00 Cum. 104.04
for making a base for road work including removing the
excavated stuff and depositing on the road side slope as
directed upto 50Mt.lead.
159 Filling in plinth with sand under floors including 101.00 Cum. 493.89
watering ramming, consolidating and dressing complete
for road work
160 Construction of granular sub-base 150 mm thick by 151.00 Cum. 1409.96
providing coarse graded machine crushed B.T. material
satisfying MOST specification of grading I (B.T. stone
aggregate 53 mm to 26.5 mm 35 %, 26.5 to 4.75 mm -
% and 2.36 mm below - 20 % )including spreading in
uniform layer with motor grader on prepared surface,
mixing by mix in place method with rotavator at OMC
and compacting with vibratory roller to achieve the
desired density etc. complete.
161 Providing and laying wet mix macadam base course 250 178.00 Cum. 1487.73
mm thick using machine crushed B.T. chips as per
required gradation mixing with required optimum
quantity of water, conveying the mix to site of work,
spreading in to grade and camber with mechanical paver
and consolidation each layer with vibratory roller
including cost of material labour plant and equipment
etc. complete.
162 Compaction and finishing of cement concrete road by 711.00 Sqm 63.63
trimix M.250 process providing extra Labour charges for
the trimix vacume dewatering service process on cement
concrete road sutface by using vacuum dewatering pump
floater surface vibrator including making groves and
rough finish to surface including leveling etc complete.
163 Providing and Laying homoginious Grey cement based 278.00 Rmt 361.64
concrete kerbing of size 30 cm x 30 cm x 10 cm size as
per detailed drawing having grade of concrete M25
grade, including necessary excavation, BBCC 1:5:10
cm as per ddetailed drawing fixing in line and level,
filling joints in CM 1:3 with smooth finished, white
washing three coats etc. complete as directed by
Engineer in charge.
Item Rate In
Description of Item Quantity Unit Amount
No figures
164 Supply. installation, testing & commissioning of ISI 1.00 No. 325000.00
approved Horizontal Split-Case type electrical motor
driven main fire pump set having 97 m3/hr. @ 70 m
head. Kirloskar make, Horizontal end suction, back
pullout, top discharge centrifugal pump with gland
packed, with all standard accessories base frame,
coupling & coupling guard and foundation bolts.The
pump unit shall be a horizontal direct mounted motor.
Motor speed shall be 3000 rpm. Unit shall comprise the
following minimum requirements:
a) Pump, b) Electric motor IE 2 type, c) Foundation bolts,
d) Air release valve, e) Mating flanges with gasket and
fasteners, f) Discharge gauges, etc. complete in all
respect. Model DB 80/26. R Motor 40H.P. / 2900 rpm.
with labour, with GST.
165 Supply. installation, testing & commissioning of ISI 1.00 No. 525000.00
approved Horizontal Split-case type diesel engine driven
stand-by fire pump set having 97 m3/hr. @ 70 m head.
The pump unit shall be a horizontallly mounted, coupled
with diesel engine. Unit shall comprise the following
minimum requirements:
a) Pump, b) Diesel Engine, c) Coupling, d) Air release
valve, i) Mating flanges with gasket and fasteners, k)
Discharge gauges, etc. complete in all respect.
Pump shall be coupled with suitable diesel engine with
heat exchanger cooled/water cooled (radiator type)
complete with base frame, anti-vibration rubber pad,
coupling with coupling guard and foundation bolts, etc.
engine shall have have a speed of 1800-2000 rpm.
Engine shall be complete with flywheel, spider coupling,
air cleaners, corrosion resistor, oil sump with lube at
pump, governor, fuel filter, starting motor, battery
charging alternator & instrument panel suitable for
volt DC including starting switches, lead acid batteries of
24V & 180 amp-harrating with termination, diesel engine
controller with supply cable from main panel to DEC,
suitable capacity of diesel oil tank (including first fill)
with all accessories, lube oil temperature gauge, lube oil
pressure, level gauge & high water temperature, flexible
exhaust connection & exhaust pipe with silencer
(insulated with asbestos rope), etc., with all complete.
with labour, with GST.
Item Rate In
Description of Item Quantity Unit Amount
No figures
166 Supply. installation, testing & commissioning of ISI 1.00 No. 94660.00
approved Vertical In-line type electrical motor driven
jockey pump set having 10.8 m3/hr. @ 70m head. The
pump unit shall be a vertically direct mounted motor.
Unit shall comprise the following minimum
requirements:
a) Pump, b) Electric motor IE2, c) Foundation bolts, d)
Mating flanges with gasket and fasteners, e) Discharge
gauges, etc. complete in all respect, with labour, with
167 Suppy, Installing, Testing and Commissioning of Normax 2.00 No. 13936.00
make C.I. Heavy duty foot valve with flangs, Nut bolts,
Gaskets etc. with necessary complete accessories.
168 Suppy, Installing, Testing and Commissioning of Normax 1.00 No. 4500.00
make C.I. Heavy duty foot valve with flangs, Nut bolts,
Gaskets etc. with necessary complete accessories. 80 mm
169 Supply, installation, testing & commissioning of common 1.00 No. 235000.00
control panel suitable for for main electrical motor
driven fire pump (1no.), Auto start of diesel engine
driven standby fire pump, & jockey electrical motor (1
no.) Auto start of Main and jockey pump, fire red powder
coated Motor Control Center with Aluminium busbar and
weather proof enclosure (IP 54) motor control center
(MCC). MCC enclosure shall be facbricated from CRCA
sheet, door & partition shall be 14 SWG complete with
incomer, Star Delta/DOL starter bus bar, protective fuses,
indicating lamps with interlock facility with bottom/top
entry with foot mounting (on channel frame) type
complete with all accessories.(all componenets of L&T &
Schneider/siemens make). With battery charger
tricle/booster arrangement for diesel battery charging.
FRLS Power & control cable for main electric pump
including earthing from motor control centre (MCC
panel) to pump & all instruments (pressure switchs) with
all complete. Power cabling & control cabling including
earthing from MCC panel to all pumps & all instruments
(pressure switches) inside pump house.
170 Providing and erecting XLPE (IS:7098)(I)88 ISI marked 50.00 No. 336.00
armoured cable multistrand Aluminium conductor for
1.1 KV to be laid with necessary clamps or in existing
cable trench / trays from Fire panel to the motors.
Item Rate In
Description of Item Quantity Unit Amount
No figures
171 Supply, installation, testing & commissioning of Priming 1.00 No 55000.00
tank,HDPE type, min. 1000 litres, necessary piping for
priming the pumps of 100 mm size, butterfly valves for
isolation, NRV 100 mm to prevent back flow, Water
Filling piping min. 50 mm size, to priming tank ,with all
172 Supply, installation, testing & commissioning of 1.00 set 70000.00
Manifold( surge vessel,)for fire hydrant system, min.
mm diameter, made from M.S plate, hydro tested to
kg./cm2. with ball valves, header with couplings for
fitting pressure switches, pressure gauges etc.with
necessary isolation valves with all complete.
173 Supply, installation, testing & commissioning of 1.00 Job 20000.00
instrumentation for automatic operation of all pump sets
including 3 nos. pressure switches and 4 nos. 150 mm
dia. dial Burdon Type Glycerine Filled pressure gauges
with SS syphon & isolation ball valve arrangements with
necessary isolation valves with all complete.
174 Supply, fabrication & erection of aboveground G.I. ERW 30.00 Mtr. 3258.00
piping, conforming to IS:1239, part-I, Heavy C class up
to 150 mm dia. and IS:3589, for size 200 mm dia. &
above, thickness. G.I. pipe fitting's as per IS: 1239, part-
II, Heavy C class for size 150 mm dia. & below & IS:
3589, min. 6.35 mm, for size 200 mm dia. above, flanges,
nuts bolts & washers, 3 mm thick gasket, pipe hangers,
Hydrostatic testing for 2 hour's at 150% of the system
pressure, hook-up etc.
Painting for piping, fittings & structural pipe support,
shall be two coat of zinc primer and two coats of fire red
conf. to IS: 5, Shade 536. Complete with all accessories as
per approved drawings, specicification and direction of
the Engineer-in-Charge, with all complete. 200 mm dia.
Item Rate In
Description of Item Quantity Unit Amount
No figures
175 Supply, fabrication & erection of aboveground G.I. ERW 30.00 Mtr. 2431.00
piping, conforming to IS:1239, part-I, Heavy C class up
to 150 mm dia. and IS:3589, for size 200 mm dia. &
above, thickness. G.I. pipe fitting's as per IS: 1239, part-
II, Heavy C class for size 150 mm dia. & below & IS:
3589, min. 6.35 mm, for size 200 mm dia. above, flanges,
nuts bolts & washers, 3 mm thick gasket, pipe hangers,
Hydrostatic testing for 2 hour's at 150% of the system
pressure, hook-up etc.
Painting for piping, fittings & structural pipe support,
shall be two coat of zinc primer and two coats of fire red
conf. to IS: 5, Shade 536. Complete with all accessories as
per approved drawings, specicification and direction of
the Engineer-in-Charge, with all complete. 150 mm dia.
176 Supply, fabrication & erection of aboveground G.I. ERW 20.00 Mtr. 1567.00
piping, conforming to IS:1239, part-I, Heavy C class up
to 150 mm dia. and IS:3589, for size 200 mm dia. &
above, thickness. G.I. pipe fitting's as per IS: 1239, part-
II, Heavy C class for size 150 mm dia. & below & IS:
3589, min. 6.35 mm, for size 200 mm dia. above, flanges,
nuts bolts & washers, 3 mm thick gasket, pipe hangers,
Hydrostatic testing for 2 hour's at 150% of the system
pressure, hook-up etc.
Painting for piping, fittings & structural pipe support,
shall be two coat of zinc primer and two coats of fire red
conf. to IS: 5, Shade 536. Complete with all accessories as
per approved drawings, specicification and direction of
the Engineer-in-Charge, with all complete. 100 mm dia.
177 Supply, fabrication & erection of aboveground G.I. ERW 20.00 Mtr. 1131.00
piping, conforming to IS:1239, part-I, Heavy C class up
to 150 mm dia. and IS:3589, for size 200 mm dia. &
above, thickness. G.I. pipe fitting's as per IS: 1239, part-
II, Heavy C class for size 150 mm dia. & below & IS:
3589, min. 6.35 mm, for size 200 mm dia. above, flanges,
nuts bolts & washers, 3 mm thick gasket, pipe hangers,
Hydrostatic testing for 2 hour's at 150% of the system
pressure, hook-up etc.
Painting for piping, fittings & structural pipe support,
shall be two coat of zinc primer and two coats of fire red
conf. to IS: 5, Shade 536. Complete with all accessories as
per approved drawings, specicification and direction of
the Engineer-in-Charge, with all complete. 80 mm dia.
Item Rate In
Description of Item Quantity Unit Amount
No figures
178 Supply, fabrication & erection of aboveground G.I. ERW 50.00 Mtr. 575.00
piping, conforming to IS:1239, part-I, Heavy C class up
to 150 mm dia. and IS:3589, for size 200 mm dia. &
above, thickness. G.I. pipe fitting's as per IS: 1239, part-
II, Heavy C class for size 150 mm dia. & below & IS:
3589, min. 6.35 mm, for size 200 mm dia. above, flanges,
nuts bolts & washers, 3 mm thick gasket, pipe hangers,
Hydrostatic testing for 2 hour's at 150% of the system
pressure, hook-up etc.
Painting for piping, fittings & structural pipe support,
shall be two coat of zinc primer and two coats of fire red
conf. to IS: 5, Shade 536. Complete with all accessories as
per approved drawings, specicification and direction of
the Engineer-in-Charge, with all complete. 50 mm dia.
179 Supply, fabrication & erection of aboveground G.I. ERW 150.00 Mtr. 365.00
piping, conforming to IS:1239, part-I, Heavy C class up
to 150 mm dia. and IS:3589, for size 200 mm dia. &
above, thickness. G.I. pipe fitting's as per IS: 1239, part-
II, Heavy C class for size 150 mm dia. & below & IS:
3589, min. 6.35 mm, for size 200 mm dia. above, flanges,
nuts bolts & washers, 3 mm thick gasket, pipe hangers,
Hydrostatic testing for 2 hour's at 150% of the system
pressure, hook-up etc.
Painting for piping, fittings & structural pipe support,
shall be two coat of zinc primer and two coats of fire red
conf. to IS: 5, Shade 536. Complete with all accessories as
per approved drawings, specicification and direction of
the Engineer-in-Charge, with all complete. 25 mm dia.
Item Rate In
Description of Item Quantity Unit Amount
No figures
180 Supply, installtion, testing & commissioing of 50.00 Mtr 3065.00
Underground GI (ERW) piping conforming to IS:1239,
part-I, Medium class ('B' class) up to 150 mm dia. and
IS:3589 heavy class ('C' class), for 200 mm dia. & above,
min. 6.35mm thickness including Medium class fittings,
anti-corrosive tape of size 150 mm wide x 4 mm thick,
wrapping & coating with 13KV holiday testing . Rates
shall include sand bedding of 75mm dia all around,
backfilling of the excavated including installation of
heavy pipe fitting's, flanges, etc.
10 % of all the welded joints shall be done
radiographically tested and 50% of the joints
radiographed shall be the "Field Joints".
Hydrostatic testing for 2 hours at 150% of the system
pressure, hook-up etc., complete with all accessories as
per approved drawings, specicification and direction of
the Engineer-in-Charge, with all complete. (Road
Crossing) 150 mm dia.
181 Supply, installtion, testing & commissioing of 10.00 Mtr 1995.00
Underground GI (ERW) piping conforming to IS:1239,
part-I, Medium class ('B' class) up to 150 mm dia. and
IS:3589 heavy class ('C' class), for 200 mm dia. & above,
min. 6.35mm thickness including Medium class fittings,
anti-corrosive tape of size 150 mm wide x 4 mm thick,
wrapping & coating with 13KV holiday testing . Rates
shall include sand bedding of 75mm dia all around,
backfilling of the excavated including installation of
heavy pipe fitting's, flanges, etc.
10 % of all the welded joints shall be done
radiographically tested and 50% of the joints
radiographed shall be the "Field Joints".
Hydrostatic testing for 2 hours at 150% of the system
pressure, hook-up etc., complete with all accessories as
per approved drawings, specicification and direction of
the Engineer-in-Charge, with all complete. (Road
Crossing) 100 mm dia
182 Supply, installation, testing & commissioning of Cast iron 2.00 No. 18750.00
body double flanged gate valve conf. to IS: 14846, PN-1.6
with mating flanges, drilling as per IS/ANSI 150# with
mating flanges, galvanized nut, bolts & washers, gasket
mm thick, etc., with all complete. 150 mm dia.
Item Rate In
Description of Item Quantity Unit Amount
No figures
183 Supply, installation, testing & commissioning of Cast iron 2.00 No. 10750.00
body double flanged gate valve conf. to IS: 14846, PN-1.6
with mating flanges, drilling as per IS/ANSI 150# with
mating flanges, galvanized nut, bolts & washers, gasket
mm thick, etc., with all complete. 100 mm dia.
184 Supply, installation, testing & commissioning of Cast iron 1.00 No. 7000.00
body double flanged gate valve conf. to IS: 14846, PN-1.6
with mating flanges, drilling as per IS/ANSI 150# with
mating flanges, galvanized nut, bolts & washers, gasket
mm thick, etc., with all complete. 50 mm dia.
185 Supply, Installation, Testing & Commissioning of Cast 2.00 No. 6750.00
iron body Butterfly valve according to IS: 13095, PN-1.6,
ISI mark, below Lever operated and above 150 mm dia.
Gear operated complete with mating flanges /ANSI class
# 150 with bolts & nuts washers, rubber gaskets 3 mm
thick, etc., with all complete. 150 mm dia.
186 Supply, Installation, Testing & Commissioning of Cast 2.00 No. 5500.00
iron body Butterfly valve according to IS: 13095, PN-1.6,
ISI mark, below Lever operated and above 150 mm dia.
Gear operated complete with mating flanges /ANSI class
# 150 with bolts & nuts washers, rubber gaskets 3 mm
thick, etc., with all complete. 100 mm dia.
187 Supply, Installation, Testing & Commissioning of Cast 1.00 No. 4550.00
iron body Butterfly valve according to IS: 13095, PN-1.6,
ISI mark, below Lever operated and above 150 mm dia.
Gear operated complete with mating flanges /ANSI class
# 150 with bolts & nuts washers, rubber gaskets 3 mm
thick, etc., with all complete. 50 mm dia.
188 Supply, installation, testing & commissioning of Cast iron 2.00 No. 5517.00
body NRV conf. to IS: 5312, PN-1.6, Dual Plate type with
S.S flap, IS mark, complete with mating Flanges/IS/ ANSI
class # 150 with bolts & nuts, washers, gaskets 3 mm
thick, etc., with all complete. 150 mm dia.
189 Supply, installation, testing & commissioning of Cast iron 2.00 No. 3700.00
body NRV conf. to IS: 5312, PN-1.6, Dual Plate type with
S.S flap, IS mark, complete with mating Flanges/IS/ ANSI
class # 150 with bolts & nuts, washers, gaskets 3 mm
thick, etc., with all complete. 100 mm dia.
190 Supply, installation, testing & commissioning of Cast iron 1.00 No. 2500.00
body NRV conf. to IS: 5312, PN-1.6, Dual Plate type with
S.S flap, IS mark, complete with mating Flanges/IS/ ANSI
class # 150 with bolts & nuts, washers, gaskets 3 mm
thick, etc., with all complete. 50 mm dia.
Item Rate In
Description of Item Quantity Unit Amount
No figures
191 Supply, installation, testing & commissioning of Four way 1.00 No. 8000.00
fire brigade Inlet connection with 63 mm dia. stainless
steel (SS304) instantaneous male inlets with built in non
return valve in each inlet with 150 mm dia. header pipe,
suitable rubber cap and GI chain including nuts, bolts,
washers, gasket 3 mm thick, etc. with all complete.As per
IS 903. ISI mark.
192 Supply, installation, testing & commissioning of Oblique 12.00 No. 4345.00
pattern type stainless steel (SS 304) single headed
External Fire Hydrant Valve , ISI, with 63 mm dia. female
instantaneous outlet conf. to IS: 5290, type - A, including
mating flanges, galvanised nuts, galvanised bolts/studs,
washers & gaskets 3 mm thick with all complete.
193 Supply, installation, testing & commissioning of 63 mm 12.00 No. 1409.00
dia., ISI , stainless steel (SS 304) Universal Branch Pipe
conf. to IS:
194 Supply & installation, testing & commissioing of Fire 12.00 No. 4759.00
Fighting Hose - conf. to IS : 636, type - A, ISI, The fire hose
shall be 15 m long with 63 mm dia. stainless steel (SS
304) couplings conf. to IS: 903, at both the ends for
connection with the hydrant valve and the branch pipe.
195 Supply, installation, testing & commissioning of 12.00 No. 2809.00
fabricated from 3 mm CRC sheet, hose boxe of size-750
mm x 600 mm x 250 mm - painted with Fire Redas per
IS: 5, shade no. 536 color from outside & white enamel
from inside , front 3 mm thick transparent glass with key,
handle and brass hinges - to accommodate 2 nos. of
mtr long hose and 1 no. universal branch pipe, including
supporting arrangement with civil work.
196 Supply, Installation, testing & commissioing of Swinging 12.00 No. 5809.00
type mild steel hose reel drum with 20 mm dia. x 30 mtr.
rubber hose as per IS:
The mounting stand shall be of mild steel and the hose
shall be fitted with a SS shut-off nozzle & SS ball valve of
25 mm dia. including supporting arrangement with all
197 Supply & Installation, Testing & Commissioing of 25 mm 4.00 No. 1100.00
dia gun metal Air Release valve with 25 mm dia. stainless
steel ball valve.
Item Rate In
Description of Item Quantity Unit Amount
No figures
198 Supply, Installation, Testing & Commissioning of Fixed 1.00 No. 27500.00
Stand Post Type Water Monitor as per IS: 8442 , monitor
having 100 mm inlet connection with flow of 1750 lpm
with all complete and 100 mm dia. gate valve, IS:
PN-1.6, with mating flanges drilling as per IS: 6392/IS:
1538/B 16.5/ASA 150#, galvanised nuts, bolts/studs &
washers, neoprene rubber gasket 3mm thick., etc. with
all complete.
199 Provide complete demonstration of whole fire system for 1.00 Job 85000.00
three years and obtaining fire NOC from SMC/ Nagar
palika for three years as per Govt. rules & Regulations.
Fees for SMC/ Nagar palika for Fire NOC will be paid by
department and other services included in this items
except Annual maintenance contract.
200 Design , Supply and installation of Safety signage made of 12.00 sq.m 2992.00
Zinc Sulphilde based glow in dark , Rigid sheet with High
Luminous property enclosed in a transperent weather
proof UV stabilized plastic pasted on 3 mm thick clear
acrylic sheet such as EXITS, EMERGENCY EXIT, DO NOT
USE LIFT DURING FIRE, FLOOR MARKINGS, FIRE LIFT,
STAIRCASE EXIT, FIRE ALARM CALL POINT, FIRE HOSE
REEL, FIRE HYDRANT POINT etc.
201 Supply, installation, testing & commissioning of Basket 2.00 No. 35000.00
Type Strainer complete with mating Flanges/IS/ ANSI
class # 150 with bolts & nuts, washers, gaskets 3 mm
thick, etc., with all complete. 150 mm dia.
202 Supply, installation, testing & commissioning of Basket 1.00 No. 13475.00
Type Strainer complete with mating Flanges/IS/ ANSI
class # 150 with bolts & nuts, washers, gaskets 3 mm
thick, etc., with all complete. 80 mm dia.
203 Supply, Installtion, Testing & Commissioing of Standard 30.00 No. 600.00
Response Sprinkler, Pendent Brass Sprinkler, Quartzoid
Bulb type with crome finish, nickel crome platde, K factor
K-80, Temp.- 680C, 1/2" end connection including
resessed escutcheon. (UL Listed).
204 Supplying of 25 mm dia UL Listed SS braided Sprinkler 30.00 No. 750.00
Flexible Hose of having 15mm end connection outlet
with supporting arrangement from false ceiling frame
and having max. test pressure of 60 bar and max.
working pressure of 12 bar at 149 deg.c. maximum
temperature. (UL Listed)
Item Rate In
Description of Item Quantity Unit Amount
No figures
205 Supply, Installation, Testing & Commissioing of UL Listed 1.00 No. 48000.00
Ductile Iron Wet Alarm Control valve, internally and
externally painted, pre-trimmed with bi-pass connection,
test and drain connection, tested to 1.5 times the
working pressure, with pressure gauge, water motor
gong, including matching flanges, galvanised bolts/studs,
nuts, washers & gaskets, with all complete. 100 mm dia.
206 Supply, Installation, Testing & Commissioning of UL 1.00 No. 5500.00
Listed Water Flow Switch, with NO & NC Contacts with
all complete. 100 mm dia.
207 Supply, Installation, Testing, & Commissioning of 8.00 No. 1950.00
Stainless Steel Ball Valve for drain, with all complete.
208 Supply, Installation and commissioning of ABC type fire 12.00 No. 2140.00
extinguisher, capacity 5 kg. as per IS 14609 /
With necessary fittings.
209 Supply, Installation and commissioning of CO2 type fire 12.00 No 6150.00
extinguisher, capacity 4.5 kg. as per IS 15222/15683.
With necessary fittings.
210 Supply, Installation, and commissioning of Fire Alarm 1.00 No. 225000.00
panel , Addressible type, 8 loops, with complete
accessories, Make Honeywell.
211 Supply, Installation, and commissioning of optical smoke 12.00 No. 2300.00
detectors with complete accessories, Make Honeywell.
212 Supply, Installation, and commissioning of Intelligent 12.00 No. 5025.00
Wall Mounted Sounder, Red with Pure White skirt
with complete accessories, Make Honeywell.
213 Supply, Installation, and commissioning of Red Add Call 12.00 No 4030.00
Point, Flush Mounting, Glass with base with complete
accessories, Make Honeywell.
214 Armour Cable for Fire Alarm system, two core, 1.5 mm2, 500.00 Mtr 120.00
FRLS type,
215 Supplying FIRE bucket round bottom of 9 litres capacity 8.00 No. 1480.00
made out of 24 gauge G.I Sheet with extra handle at
bottom duly painted white inside and Red out side with
FIRE mark. Filled with dry-sand and kept on existing
stand provided or hung on wall hook.
216 Supplying and erecting floor mounting Stand for keeping 2.00 No. 4000.00
four nos. of FIRE buckets comprising 1500 mm in length,
900 mm height frame made out of 30mm x 30 mm x
mm angle iron with cross suports legs, welded with
hooks and duly painted with one coat of red lead and two
coats of approved enamelled silver paint.
217 Supplying of well rotted FYM manure with all lead and 4.00 Cum. 378.75
Lift including spreading mixing dressing and rolling with
hand roller etc. complete.
Item Rate In
Description of Item Quantity Unit Amount
No figures
218 Scarifying the surface of Soil including spreading of DAP 135.00 Sqm 26.26
fertilizer mixing with Soil properly levelling gand
dressing of the plot
219 Supplying and planting Dibbing semi carpet lawn at 135.00 Sqm 20.20
distance of abour 15 cm x 15 cm after proper anti termite
teratment amd rolling the seme by hand roller amd
wetering etc complete.
220 Bowing and developing flowering plants grown in nusery 7.00 No. 30.30
having approximate height 4 to 5 ft or Height ad per
Landscaps Plan with natural growith of soil packed in
polithyline bag or Earthern pot. Including organic &
chemical fertilizer Pesticides, fungicides, hormones &
maintaining the plants up to three months as deserted.
Bottol palm.
221 Bowing and developing flowering plants grown in nusery 4.00 No. 60.60
having approximate height 4 to 5 ft or Height ad per
Landscaps Plan with natural growith and nature colour
planted in alump of soil packed in polithyline bag or
Earthern pot. Including organic & chemical fertilizer
pesticides, fungicides hormones & maintaining the plants
uo to three months as deserted Trinagle Plan.
222 Bowing and developing flowering plants grown in nusery 7.00 No. 60.60
having approximate height 4 to 5 ft or Height ad per
Landscaps Plan with natural growith and nature colour
planted in alump of soil packed in polithyline bag or
Earthern pot. Including organic & chemical fertilizer
pesticides, fungicides hormones & maintaining the plants
uo to three months as Jasud
223 Bowing and developing flowering plants grown in nusery 5.00 No. 75.75
having approximate height 4 to 5 ft or Height ad per
Landscaps Plan with natural growith and nature colour
planted in alump of soil packed in polithyline bag or
Earthern pot. Including organic & chemical fertilizer
pesticides, fungicides hormones & maintaining the plants
uo to three months as Croton
224 Bowing and developing flowering plants grown in nusery 5.00 No. 10.10
having approximate height 4 to 5 ft or Height ad per
Landscaps Plan with natural growith and nature colour
planted in alump of soil packed in polithyline bag or
Earthern pot. Including organic & chemical fertilizer
pesticides, fungicides hormones & maintaining the plants
uo to three months as deserted green mahindi
Item Rate In
Description of Item Quantity Unit Amount
No figures
225 Bowing and developing flowering plants grown in nusery 3.00 No. 15.15
having approximate height 4 to 5 ft or Height ad per
Landscaps Plan with natural growith and nature colour
planted in alump of soil packed in polithyline bag or
Earthern pot. Including organic & chemical fertilizer
pesticides, fungicides hormones & maintaining the plants
uo to three months as deserted New block ficus.
226 Labour charges for planting various plantsafter proper 31.00 No. 40.40
anti termite treatment in pits including placing property
and filling the pit with requred prepared mix soil and
wetering and dispporting etc complete.
227 Maintance of the garder for 60 days after Complition of 3 1.00 Job. 10100.00
month stipulated period is completed for plantation o
lawn and plants including applying second round of
proper antitermite tretment.
228 Providnig and fixing to wall ceiling and floor 80 Schedule 40.00 Rmt 442.04
Syntex / Astra (CPCV) or equivalent of the following
nominal bore tube fittings and clamps the wall ceiling
and floor (C) 40 mm
229 Providing and fixing consealed to wall, ceiling and floor 40.00 Rmt 205.00
80 Schedule Syntex / Astral (CPVC) or equivalent brand
of the following nominal bore tube fittings and clamps
including Making goods the wall ceilling and floor (A)
230 Providing and fixing brass screw doen stop cock (A) 15 1.00 Rmt 287.85
231 Rubber Hose pope 15 mm dia of approved brand and 100.00 Rmt 25.25
232 Providnig and fixing G I Nipple as directed. 1.00 No. 20.20
233 Earthwork for embankment including breaking clods, 14928.16 Cum 230.31
dressing with all lead and lift (excluding watering and
consolidation)(E) From Borrow area within 3.0 Km. lead
234 Rolling of Earth work in layers with power roller 14928.17 Cum 22.63
including filling in depressions which occure during the
235 Steel work, welded in built up sections framed work 21725.00 kg 90.48
including cutting, hoisting, fixing in position and applying
a priming coat of read lead paint & two coat oil paint.
(A)In beams and joists, channels angles Tees, flats, with
connecting plates or angle cleats as in main and cross
beams. Hip and jack rafters, purlins conneted to common
rafters and the like..
Item Rate In
Description of Item Quantity Unit Amount
No figures
236 Providing and fixing of Ridge flashing for roof panel shall 600.00 kg 858.67
be made out of 0.5 mm thick pre coated GI sheet . The
Precoated sheet shall be of minimum 240 mpa steel
grade confirming to IS 14246:1995 and shall have zinc
coating of minimum 120 gsm as per IS:277:1992 , 5-7
microns epoxy primer on both side of the sheet and
polyester top coat 15-18 micron. The PPGI Sheet shall
have plastic protective guard film of minimum
microns to avoid scratches during transportation. The
ridge shall be fixed to the steel members by pop rivet or
self drilling/self stitching fastners @ maximum 450 mm
c/c along length of capping/flashing etc complete .
237 Providing and fixing concertina coil fencing with 457.00 Rmt 399.96
punched tape concertina coil 600 mm dia 10 mt openable
length having 50 no rounds per 6 mt length, upto 3mt
height of wall with existing angle iron (50mm x50mm
x5mm )requird shaped As per Directed Engeenier in
charge. placed 2.4mt or 3.00mt apart and with
horizontal R.B.T. reinforced barbed wire(3 mm) , stud
tied with G.I. staples and G.I. clips to retain horizontal,
including necessary bolts or G.I.barbed wire tied to angle
iron, all complete as per direction of Engineer-in-charge,
with reinforced barbed tape (R.B.T.)/Spring core (2.5
mm thick) and weight 43.478 gm/meter at compound
wall for ESR M4/ intakewell.
238 Providing and laying controlled cement concrete M-250 658.08 Cumt 5943.85
and curing complete including the cost of form work but
excluding the cost of reinforcement for reinforced
concrete work in Retaning wall
239 Providing and filter media 600mm thick as directed at 639.80 Sqmt 1248.74
the back of Protection Wall as per detailed specification.
240 Point wiring for Light / Bell with 2-1.5 sq.mm & earth 372.00 Pt. 485.81
wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV
grade FRLS PVC insulated multi strand copper wires up
to 10 mtr length , in below type of pipe erected with 6A
Modular type switch / bell push & accessories and earth
continuity of following type, erected on PVC /
Metallic/Wooden box, single mounting base frame
covered with textured/metallic/white front plate
modules erected on / in wall / ceiling as per pipe
erected, with necessary Lamp holder/ceiling rose /
H.D.Connector as directed. (f) with medium class Rigid
PVC pipe and accessories erected concealed in
wall/ceiling complete Cat. III
Item Rate In
Description of Item Quantity Unit Amount
No figures
241 Point wiring for Light / Bell with 2-1.5 sq.mm & earth 130.00 Pt. 242.91
wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV
grade FRLS PVC insulated multi strand copper wires up
to 10 mtr length , in below type of pipe erected with 6A
Modular type switch / bell push & accessories and earth
continuity of following type, erected on PVC /
Metallic/Wooden box, single mounting base frame
covered with textured/metallic/white front plate
modules erected on / in wall / ceiling as per pipe
erected, with necessary Lamp holder/ceiling rose /
H.D.Connector as directed. (f) with medium class Rigid
PVC pipe and accessories erected concealed in
wall/ceiling complete Cat. III W/C Point
242 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 145.00 Pt. 674.68
1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade
FRLS PVC insulated multi strand copper wires up to
mtr length, in below type of pipe erected with 6A
Modular type switch and hum free EME step type
electronic fan regulator mounted and accessories with
earth continuity of following type erected on PVC /
Metallic/Wooden box, single mounting base frame
covered with textured/metallic/white front plate
modules erected on / in wall / ceiling as per pipe erected.
with necessary ceiling rose / H.D.Connector as directed.
(f) with medium class Rigid PVC pipe and accessories
erected concealed in wall/ceiling complete.Cat. III
243 Point wiring for Individual Plug with & earth wire of 1.5 3.00 Pt. 510.05
sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS
PVC insulated multi strand copper wires up to 10 mtr
length, in below type of pipe erected complete with
Modular type switch & 5 pin Plug erected on PVC /
Metallic/Wooden box covered with appropriate front
plate modules erected on / in wall / ceiling as per pipe
erected with following type of accessories. [I] For 6A Plug
and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby
switchboard/mcb db board (f) with medium class Rigid
PVC pipe and accessories erected concealed in
wall/ceiling complete Cat. III
Item Rate In
Description of Item Quantity Unit Amount
No figures
244 Point wiring for Individual Plug with & earth wire of 1.5 2.00 Pt. 745.38
sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS
PVC insulated multi strand copper wires up to 10 mtr
length, in below type of pipe erected complete with
Modular type switch & 5 pin Plug erected on PVC /
Metallic/Wooden box covered with appropriate front
plate modules erected on / in wall / ceiling as per pipe
erected with following type of accessories. [II] For 16A
Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from
mcb db board.(f) with medium class Rigid PVC pipe and
accessories erected concealed in wall/ceiling complete
245 Point wiring for on board Looped Plug with 6A Modular 122.00 Pt. 257.55
type switch & 5 pin socket erected on PVC /
Metallic/Wooden box, single mounting base frame
covered with textured / metallic/white front plate
modules erected on / in wall / ceiling with following
type accessories Cat. III
246 Providing following type of Modular Type Accessories 225.00 Ea. 151.50
mounted with PVC / metallic/Wooden box, single
mounting base frame covered with textured /
metallic/white front plate , modules erected with
necessary connections as per site situation directed by
Engineer In charge. (1)One No. SP 6 Amp. Cat.III
247 Providing following type of Modular Type Accessories 225.00 Ea. 151.50
mounted with PVC / metallic/Wooden box, single
mounting base frame covered with textured /
metallic/white front plate , modules erected with
necessary connections as per site situation directed by
Engineer In charge. (2) One No 5 pin plug Cat.III
248 Providing following type of Modular Type Accessories 11.00 Ea. 180.79
mounted with PVC / metallic/Wooden box, single
mounting base frame covered with textured /
metallic/white front plate , modules erected with
necessary connections as per site situation directed by
Engineer In charge. (9) 16 Amp. SP one way switch
249 Providing following type of Modular Type Accessories 33.00 Ea. 199.98
mounted with PVC / metallic/Wooden box, single
mounting base frame covered with textured /
metallic/white front plate , modules erected with
necessary connections as per site situation directed by
Engineer In charge. (10) 6/16Amp. Universal socket
Item Rate In
Description of Item Quantity Unit Amount
No figures
250 Providing following type of Modular Type Accessories 22.00 Ea. 410.06
mounted with PVC / metallic/Wooden box, single
mounting base frame covered with textured /
metallic/white front plate , modules erected with
necessary connections as per site situation directed by
Engineer In charge. (14) 6A/ 10A/ 16A/ 20A/ 25A/ 32A
Double Pole Modular MCB Switch
251 Providing and erecting ISI mark Medium class RIGID PVC 1290.00 Mtr. 24.24
PIPES of following size complete to be erected on/in wall
or ceiling erected with necessary PVC fittings & Junction
boxes fixed with adhesive solution & Clamps with
following dia of pipes, in approved manner as directed
252 Supplying and laying UPVC cable trunking system 140.00 Mtr. 277.75
comprising unplasticised polyvinyl, chloride rigid
material with ignition free and flame proof confirming BS
with necessary end caps Internal and external bend, flat
bends, coupler, tee etc..All necessary accessories and
measuring of following sizes (1) 75 mm x 50 mm
253 Providing and erecting Mains with 1.1 KV grade FRLS 4404.00 Mtr. 82.82
PVC insulated ISI marked stranded Copper conductor
wire in following type of pipe to be erected concealed in
/flushed on wall/ceiling, with 1.5 sq. mm copper
conductor FRLS PVC insulated stranded wire of green
colour for earth continuity of following size (A) With
medium class Rigid PVC pipe and accessories (b) 2 wire
254 Providing and erecting Mains with 1.1 KV grade FRLS 440.00 Mtr. 112.11
PVC insulated ISI marked stranded Copper conductor
wire in following type of pipe to be erected in / on wall /
ceiling with 2.5 sq. mm copper conductor FRLS PVC
insulated stranded wire of green colour for earth
continuity of following size (A) with medium class Rigid
PVC pipe and accessories (a) 2 wire 4 sq. mm
255 Providing and erecting Mains with 1.1 KV grade FRLS 360.00 Mtr. 147.46
PVC insulated ISI marked stranded Copper conductor
wire in following type of pipe to be erected in / on wall /
ceiling with 2.5 sq. mm copper conductor FRLS PVC
insulated stranded wire of green colour for earth
continuity of following size (b) 2 wire 6 sq. mm
256 Providing and erecting Mains with 1.1 KV grade FRLS 180.00 Mtr. 260.58
PVC insulated ISI marked stranded Copper conductor
wire in following type of pipe to be erected in / on wall /
ceiling with 2.5 sq. mm copper conductor FRLS PVC
insulated stranded wire of green colour for earth
continuity of following size (h) 4 wire 6 sq. mm
Item Rate In
Description of Item Quantity Unit Amount
No figures
257 Providing and erecting Mains with ISI marked, 1.5KV 176.00 Mtr. 56.56
grade electrolyte multi stranded, annealed copper
conductor with heat resistant PVC insulated conforms to
IS 694, IEC - 227 erected in existing pipe of following
size (Specifically for control panel, relays, power
switchgears, motor starters & control wiring) with
required size of copper lugs, nuts and bolts if required.
(e) One wire 6.00 sq. mm
258 Providing and erecting Mains with ISI marked, 1.5KV 88.00 Mtr. 300.98
grade electrolyte multi stranded, annealed copper
conductor with heat resistant PVC insulated conforms to
IS 694, IEC - 227 erected in existing pipe of following
size (Specifically for control panel, relays, power
switchgears, motor starters & control wiring) with
required size of copper lugs, nuts and bolts if required.
(i) One wire 35.00 sq. mm
259 Supplying and erecting Flexible PVC insulated multi 1290.00 Mtr. 22.22
strand multi core 1.1 kv grade ISI marked copper wires
of following size to be erected as directed. (c) 1.00 Sq.mm
2 core round/ flat PVC sheathed
260 Supplying and erecting Flexible PVC insulated multi 146.00 Mtr. 46.46
strand multi core 1.1 kv grade ISI marked copper wires
of following size to be erected as directed. (e)
Sq.mm 3 core round PVC sheathed
261 Providing & erecting Switch board for Computer or 9.00 Ea. 1133.22
electric apparatus consisting of following modular type
accessories mounted with PVC / Metallic
concealed/open box with single mounting base frame
covered with textured/metallic /white front
plate,modules erected with necessary connections as
1 no. 6A/16A universal plug-switch combined.
3 nos. 6A Switch
3 nos. 6A 5 pin Plug For Modular Type Accessories Cat.
262 Decorative call bell Ting-tong box type 250 volts 1.00 Ea. 71.71
complete erected
Item Rate In
Description of Item Quantity Unit Amount
No figures
263 Supplying and erecting LED indoor fittings with LEDs of 328.00 Ea. 535.30
wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,
with housing used as a heat sink shall be made of thick
sheet Steel conforming to IS: 513/CRCA/ aluminium die
cast powder coated and high U.V. & corrosion resistance
with diffuser with company mark/name 160V to 270V,
Power Factor more than 0.9, THD < 15%, CCT 3000 K to
6500K, Luminaire efficacy> 85 lumens/watt ,LED LED
driver efficiency > 85 %( fitting required LM-79 & LM-80
Certificates)(NOTE: Below description have shown
ranges of Wattage capacity of LED fittings.The Engineer
ranges shown.) (A) Tube Light with integral driver (v) 36-
40 Watts, Surge-2 KV, IP-20, conventional 4 feet Cat-lll
264 Supplying and erecting led lamps with following wattage 130.00 Ea. 112.11
capacity of 220 to 240 voltage, minimum 15000 burning
hours life, 500 V in built-surge protection,Polycarbonate
diffuser, mounting suitable for E14 / E27 / B22 lamp
holders, pf >= 0.5 (A) LED Lamps integral type, with PC
diffuser suitable LAMP holder (ii) 5 to 8 watts Cat-III
265 Supplying and erecting LED street light / Flood light 21.00 Ea. 5976.17
fittings with High power White LEDs wattage of 3 Watt
and above assembled on single MCPCB, efficiency more
than 130 lm/w and corrosion free High pressure die cast
aluminum housing with smooth finish powder coated
and heat sink extruded aluminium with diffuser and
Polycarbonate optics/ lenses, with toughened glass with
company mark/name engraved or embossed 160 to
V,Power Factor more than 0.95, THD < 10 %, CCT
K to 5700K,Uniformity ratio >0.45, Luminaire efficacy>
100 lumens/watt . LED driver efficiency > 85 %.( fittings
required LM-79 & LM-80 certificates)(NOTE: Below
description have shown ranges of Wattage capacity of
wattage capacity between the ranges shown.) (A) Street
Light (IP-65), Surge protection -4KV integral and ,Light
must have 440VAC line supply with over-voltage
protection. (A) Street Light (IP-65), Surge protection -
4KV integral and ,Light must have 440VAC line supply
with over-voltage protection. (iii) Above 60 to 90 watts
Item Rate In
Description of Item Quantity Unit Amount
No figures
266 Supplying and erecting LED street light / Flood light 4.00 Ea. 9647.52
fittings with High power White LEDs wattage of 3 Watt
and above assembled on single MCPCB, efficiency more
than 130 lm/w and corrosion free High pressure die cast
aluminum housing with smooth finish powder coated
and heat sink extruded aluminium with diffuser and
Polycarbonate optics/ lenses, with toughened glass with
company mark/name engraved or embossed 160 to
V,Power Factor more than 0.95, THD < 10 %, CCT
K to 5700K,Uniformity ratio >0.45, Luminaire efficacy>
100 lumens/watt . LED driver efficiency > 85 %.( fittings
required LM-79 & LM-80 certificates)(NOTE: Below
description have shown ranges of Wattage capacity of
wattage capacity between the ranges shown.) (B) Flood
Light (IP-65), Surge protection -4KV integral and ,Light
must have 440VAC line supply with over-voltage
protection. (vii) (vi)above 160 to 200 watts Cat-lll
267 Supplying and erecting LED street light / Flood light 2.00 Ea. 4819.72
fittings with High power White LEDs wattage of 3 Watt
and above assembled on single MCPCB, efficiency more
than 130 lm/w and corrosion free High pressure die cast
aluminum housing with smooth finish powder coated
and heat sink extruded aluminium with diffuser and
Polycarbonate optics/ lenses, with toughened glass with
company mark/name engraved or embossed 160 to
V,Power Factor more than 0.95, THD < 10 %, CCT
K to 5700K,Uniformity ratio >0.45, Luminaire efficacy>
100 lumens/watt . LED driver efficiency > 85 %.( fittings
required LM-79 & LM-80 certificates)(NOTE: Below
description have shown ranges of Wattage capacity of
wattage capacity between the ranges shown.) (C) Post
Top Lantern LED fitting comprises of finish cast
aluminum spigot and spun aluminum canopy fixed with
opal polycarbonate, pipe arrangement for vertical
mounting driver and accessories wired upto terminal
block.IP 65 (ii)32-40W Cat-lll
Item Rate In
Description of Item Quantity Unit Amount
No figures
268 Pproviding and erecting Approved make Four pole 2.00 Ea. 6173.12
moulded case circuit breaker having breaking capacity
ICU of 25 KA. at 415 V,having normal current rating up to
25 A to 100A. with Fixed thermal & magnetic release
suitable to work on A.C. supply 50 c/s. with all internal
connections, spreader tinned copper & complete erected
in existing 16 G.M.S. housing.ICS=100% of ICU only Cat III
269 Providing and erecting Approved make Four pole 8.00 Ea. 8055.76
moulded case circuit breaker having breaking capacity
ICU of 35 KA. at 415 V. having normal current rating
125A. with Fixed thermal & magnetic release suitable to
work on A.C.supply 50 c/s. with all internal connections,
spreader tinned copper & complete erected in existing
16 G.M.S. housing. ICS=100% of ICU only
270 Providing and erecting Approved make Four pole 5.00 Ea. 16221.61
moulded case circuit breaker having breaking capacity
ICU of 35 KA. at 415 V. having Normal current rating
200A.with variable Thermal & magnetic release suitable
to work on A.C.supply 50 c/s. with all internal
connections, spreader tinned copper & complete erected
in existing 16 G.M.S.housing ICS=100% of ICU only
271 Providing and erecting Approved make Four pole 3.00 Ea. 20946.39
moulded case circuit breaker having breaking capacity
ICU of 35 KA. and above at 415 V . having normal current
rating 250A. with variable thermal & magnetic release
suitable to work on A.C.supply 50 c/s. with all internal
connections, spreader tinned copper & complete erected
in existing 16 G.M.S. housing. ICS=100% of ICU only
272 Supplying & erecting approved make Four Pole 415V 1.00 Ea. 13353.21
change over switch interior for panel mounting with
operating mechanism A.C.23 duty confirming to IS for
(E)250A / 320A Cat-lll
273 Supplying and erecting triple pole & neutral 440V / 500V 4.00 Rn.Mtr 1961.42
panel mounting Copper Busbars with four equal Nos. of
electrolyte bus having current density not more than
Amp. / sq.mm (Rated current / cross section area) duly
wrapped with colour insulating tape for phase sequence
of following current carrying capacity, erected with
necessary bus bar supports /insulators, main cable
socket to each bar, erected in existing cubical panel with
necessary connections. (A) Suitable for 100 Amp.
Item Rate In
Description of Item Quantity Unit Amount
No figures
274 Supplying and erecting triple pole & neutral 440V / 500V 2.00 Rn.Mtr 3202.71
panel mounting Copper Busbars with four equal Nos. of
electrolyte bus having current density not more than
Amp. / sq.mm (Rated current / cross section area) duly
wrapped with colour insulating tape for phase sequence
of following current carrying capacity, erected with
necessary bus bar supports /insulators, main cable
socket to each bar, erected in existing cubical panel with
necessary connections. (B) Suitable for 200 Amp.
275 Supplying and erecting triple pole & neutral 440V / 500V 1.50 Rn.Mtr 4909.61
panel mounting Copper Busbars with four equal Nos. of
electrolyte bus having current density not more than
Amp. / sq.mm (Rated current / cross section area) duly
wrapped with colour insulating tape for phase sequence
of following current carrying capacity, erected with
necessary bus bar supports /insulators, main cable
socket to each bar, erected in existing cubical panel with
necessary connections. (C) Suitable for 300 Amp.
276 Providing and erecting Miniature circuit breaker single 195.00 Ea. 112.11
pole 6A to 25A suitable to operate on 240 V A.C. system
and having breaking capacity 10 KA to be erected in
existing box. confirming to IS 8828/1996 with ISI Mark
277 Providing & erecting 240 V MCB double pole switch for 15.00 Ea. 278.76
lighting Load (B Curve) having 10 KA breaking capacity &
confirms to IS : 8828 in existing box having following
capacity (A) 6 to 32 Amp. Cat.III
278 Providing & erecting 240 V MCB double pole switch for 36.00 Ea. 295.93
lighting Load (B Curve) having 10 KA breaking capacity &
confirms to IS : 8828 in existing box having following
capacity (B) 40 Amp. Cat.III
279 Providing & erecting 415V MCB Four Pole Switch for 25.00 Ea. 638.32
Lighting Load (B curve) having 10KA breaking capacity &
confirms to IS :8828 in existing box having following
capacity (b)40 Amp. Cat.III
280 Sheets steel powder coated enclosure suitable for 14.00 Ea. 176.75
incorporating One/Two nos. MCB.
281 Providing and erecting Sheet Steel powder coated MCB 14.00 Ea. 1492.78
distribution board - flush / surface mounted fitted with
busbar, neutral link, earth bar and DIN rail, Conforms to
IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house
appropriate nos. of MCBs.(The DBs should be used of
same company of MCB to be used) suitable for (A) single
phase incoming and horizontal single phase outgoing (b)
sheet steel double door (IP-43) (iv)12 way
Item Rate In
Description of Item Quantity Unit Amount
No figures
282 Providing and erecting Sheet Steel powder coated MCB 6.00 Ea. 2339.16
distribution board - flush / surface mounted fitted with
busbar, neutral link, earth bar and DIN rail, Conforms to
IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house
appropriate nos. of MCBs.(The DBs should be used of
same company of MCB to be used) suitable for (B) three
phase incoming and single phase horizontal type
outgoing Per phase isolation type (PPI) (b) sheet steel
double door (i)4 way
283 Providing and erecting Approved make RCCBs 14.00 Ea. 1969.50
conforming to IS: 12640 and having sensitivity of 30 mA
and Short Circuit withstand capacity of 10 KA and
suitable for operation on single phase 240 V,50Hz.
having characteristic of quick action & tripping with all
advance feature & do not incorporate any electronic
component. for following Max. rating erected as directed
(i) 25 Amps.DP Cat. III
284 Providing and erecting Approved make RCCBs 34.00 Ea. 2235.13
conforming to IS: 12640 and having sensitivity of 30 mA
and Short Circuit withstand capacity of 10 KA and
suitable for operation on single phase 240 V,50Hz.
having characteristic of quick action & tripping with all
advance feature & do not incorporate any electronic
component. for following Max. rating erected as directed
(ii) 40Amps. DP Cat. III
285 Providing and erecting Annealed bare Copper wire 8 to 17.00 Kg. 794.87
286 Providing and erecting HOT deep Galvanised iron strip 57.00 Kg. 77.77
wire 8 to 16 SWG.
287 Providing and erecting Pipe type earthing having 150 10.00 Ea. 368.65
cms.long and 2.5 cms. dia. galvanised iron pipe with
coupling and buch buried in specially prepared earth pit
complete with necessary 8 SWG earth wire.
288 For using salt and charcoal / coke as required for pipe 10.00 Ea. 171.70
type earthing.
Item Rate In
Description of Item Quantity Unit Amount
No figures
289 Supplying & erecting earth pit of minimum bore 7.00 Ea. 4591.46
dia.150mm size approved make Earthing Electrode
consisting Pipe-in-Pipe Technology as per IS 3043-1987
made of corrosion free hot dipped G.I.Pipes having Outer
pipe dia of 50mm having 80-200 Micron galvanising,
Inner pipe dia of 25 mm having 200-250 Micron
galvanising, connection terminal dia of 12mm with
constant ohmic value surrounded by highly conductive
compound with high charge dissipation suitable for
following type of applications with chamber and heavy
duty cover. (A)(approved make OEM has to submit test
certificate including value of earth resistance of
installation duly stamped and signed by agency and
officer Incharge has to ensure the value of earthing
resistane mentioned in test Certificate) & having back
filling compound of (B) Inner chemical (CCM Compound)-
Resistivity:- 0.2 ohm / meter testing as per IEC 62561-
2017, Voltage drop:- < 1 volt at no load & dry form,
Sulphar content:- <2%(C) Back fill Compound :- Earthing
compound should be capable to retain moisture for long
time Necessary test report must be submitted by Agency.
(a) For Electrical Installation up to 440V in normal soil
Length of pipe - 1 Mtr
Back filling compound - 1 Nos Bag of 15 Kg.
Item Rate In
Description of Item Quantity Unit Amount
No figures
290 Providing & erecting weather proof, dust & vermin proof, 9.40 Sq.Mtr 10468.65
floor mounted front operated indoor type cubical panel
board necessary IP-42 and above protection as per
approval from engineer incharge made from 14 SWG
thick CRC M.S. sheet for outer body & doors, 16 SWG
thick CRC M.S.sheet for internal partitions with necessary
accesories , supporting angles/ flats channel including
cutting, bending, drilling, welding, riveting with internal
partitions & cable alley as per requirements & instruction
of engineer-in-charge with erection of supplied switch
gears, BUSBARS, suitable size of inter connecting PVC
copper wire / copper-aluminium strips, rubber
grommets, rib, bakelite control fuses/MCB for measuring
instruments, earth bus & earth bolts, foundation flange -
bolts-base Plates, sufficient nos. of hinged doors, handles
with locking arrangement and rubber gasket,heavy duty
end terminal connection,danger notice board,necessary
ventilation,earthing strip complete. The Panel shall be
painted with epoxy powder coating. (The rates excludes
the cost of switchgears, bus bars, inter connecting mains
& Copper Aluminium strips, meters, Fuses etc. The
dimension shall be measured excluding base beams) The
panel shall be supplied with following approved
manufacturers with following size. (A) locally fabricated
panel board (i) with 350mm depth
291 Providing , erecting , fabricating the M.S. structure as per 145.00 Kg. 77.77
requirement on site incorporating proper size of M.S.
angles,square,round, flats, bars, channels, sections
complete with cutting, welding, grinding & finishing duly
painted with one coat of red oxide with erection on site
as per direction of engineer in charge with necessary
grouting, cementing, plastering & finishing complete.
292 Providing and erecting XLPE(IS:7098)(I)-88 ISI 50.00 Mtr. 378.75
armoured cable multistrand Aluminium conductor for
1.1 KV. to be laid on wall with necessary clamps or in
existing trench / pipe of following size of cables (D)
1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)
293 Providing and erecting XLPE(IS:7098)(I)-88 ISI 155.00 Mtr. 490.86
armoured cable multistrand Aluminium conductor for
1.1 KV. to be laid on wall with necessary clamps or in
existing trench / pipe of following size of cables (E)
1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core)
Item Rate In
Description of Item Quantity Unit Amount
No figures
294 Providing and erecting XLPE(IS:7098)(I)-88 ISI 55.00 Mtr. 540.35
armoured cable multistrand Aluminium conductor for
1.1 KV. to be laid on wall with necessary clamps or in
existing trench / pipe of following size of cables (F)
1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core)
295 Providing and erecting XLPE (IS:7098)(I)-88 ISI 646.00 Mtr. 126.25
armoured cable multistrand / Solid Aluminium
conductor for 1.1 KV. to be laid on wall with necessary
clamps or in existing trench / pipe of following size of
cables (B) 4 core 6 Sq. mm
296 Making trench in soft soil of suitable width of 90 cm deep 523.00 Mtr. 55.55
for laying cable or locating the fault all over the run and
back filling the same and making the surface as normal
297 Supplying following size of Light duty “A” Class G.I . Pipe 30.00 Mtr. 300.98
& erecting as directed by Engineer-in-charge. (B) 50 mm
298 Supplying following size of Light duty “A” Class G.I . Pipe 30.00 Mtr. 696.90
& erecting as directed by Engineer-in-charge. (D)
299 Providing & laying approved make Double walled 417.00 Mtr. 62.62
corrugated pipes (DWC) of polyethylene(conforming to
IS 14930 II )with necessary connecting accessories of
same material at required depth in existing trench for
laying of cable. below ground / road surface for
enclosing cable (A)50 mm outer dia
300 Providing & laying approved make Double walled 104.00 Mtr. 137.36
corrugated pipes (DWC) of polyethylene(conforming to
IS 14930 II )with necessary connecting accessories of
same material at required depth in existing trench for
laying of cable. below ground / road surface for
enclosing cable (D)120 mm outer dia.
301 Providing and, fixing heavy duty flange type brass cable 16.00 Ea. 38.38
gland with rubber ring for PVC insulated armoured cable
complete with out going tails, insulating tape etc for
following size of cables. (B) 2 to 4 core 6 Sq. mm
302 Providing and, fixing heavy duty flange type brass double 10.00 Ea. 103.02
compression type cable gland with rubber ring for PVC
insulated armoured cable complete with out going tails,
insulating tape etc for following size of cables. (C) 3 &
1/2 core 70 Sq. mm
Item Rate In
Description of Item Quantity Unit Amount
No figures
303 Providing and, fixing heavy duty flange type brass double 4.00 Ea. 131.30
compression type cable gland with rubber ring for PVC
insulated armoured cable complete with out going tails,
insulating tape etc for following size of cables. (D) 3 &
1/2 core 95 Sq. mm
304 Providing and, fixing heavy duty flange type brass double 6.00 Ea. 140.39
compression type cable gland with rubber ring for PVC
insulated armoured cable complete with out going tails,
insulating tape etc for following size of cables. (E) 3 &
1/2 core 120 Sq. mm
305 Solder less crimping type Aluminium lugs conforming to 14.00 Ea. 20.20
IS suitable for cable of following size evenly crimped with
high pressure tool & connected to switchgear terminals
with brass/cadmium plated nut bolts in an approved
manner. (D) 35/50 Sq.mm.
306 Solder less crimping type Aluminium lugs conforming to 36.00 Ea. 25.25
IS suitable for cable of following size evenly crimped with
high pressure tool & connected to switchgear terminals
with brass/cadmium plated nut bolts in an approved
manner. (E) 70 Sq.mm.
307 Solder less crimping type Aluminium lugs conforming to 6.00 Ea. 40.40
IS suitable for cable of following size evenly crimped with
high pressure tool & connected to switchgear terminals
with brass/cadmium plated nut bolts in an approved
manner. (F) 95 Sq.mm.
308 Solder less crimping type Aluminium lugs conforming to 28.00 Ea. 45.45
IS suitable for cable of following size evenly crimped with
high pressure tool & connected to switchgear terminals
with brass/cadmium plated nut bolts in an approved
manner. (G) 120 Sq.mm.
309 Providing & erecting Approved make Power Saving 50 145.00 Ea. 1948.29
Watt Ceiling Fan with double ball bearing ISI mark with
Condenser 230 volt A.C. 50 Hz 1200 mm sweep
complete having 3blades with aluminium blades with
canopy & 30 cm. down rod erected with earthing.(Make
shall be approved by Engineer in charge))
310 Supplying and erecting 19 / 20 mm. nominal bore 145.00 Mtr. 108.07
Medium Class M.S. Pipe down rod erected duly painted
for fan complete with proper insulation without leakage
and earthing.
Item Rate In
Description of Item Quantity Unit Amount
No figures
311 Supplying & erecting fan hook box of 10 mm M.S. round 145.00 Ea. 108.07
bar bounded to the RCC bars up to 50mm length each
side and pierced through a 16 Gauge M.S. box / Heavy
Duty PVC box complete erected concealed in Ceiling with
necessary finishing.
312 Providing 2.5mm.thick laminated acrylic sheet to cover 145.00 Ea. 18.18
the fan hook or Fan box.
313 Supplying & erecting approved make low noise 5.00 Ea. 1366.53
decorative exhaust fan having square frame ABS body
with inbuilt lowers & square frame. 250mm with
RPM Cat.II
314 Supplying & erecting single phase approved make 38.00 Ea. 2054.34
industrial exhaust fan suitable for medium duty ring
mounted low noise operation suitable for medium duty
having following dia size and maximum speed in RPM [A]
305 mm dia 900 RPM Cat.II
315 Supplying and erecting approved make Octagonal pole 16.00 Ea. 8192.11
made from HR sheet steel. The pole should be made as
per IS. and shall be coated with hot dip galvanizing as per
IS 2629/2633/4759, suitable suspend local wind speed
with integral Junction box consist of terminal plate of min
6mm Hylam sheet, standard profile 35mmX7.5mm Din-
Rail for MCB Mounting, stud type terminal and
arrangement for cable termination to be erected With
Suitable foundation (Included) as per details given by
manufacturer considering site requirement. (D) 6 Mtr.
Long 70 mm Top X 135 mm bottom dia, 3 mm thickness
with 200mmX200mmX12mm base plate, 4-M20 Bolts
and 600mm long J-Bolt.Approx Pole weight 59 kg
316 Supplying & erecting approved make SMC press 6.00 Ea. 515.10
moulded composite FRP. loop-in, loop-out approx. 2mm
thick box complete with Bakelite connector strip
5way(3P+N+E),DIN rail for mounting mob & hinged
doors as per requirement having locking arrangements
with mounting clamp with nuts, bolts & washers suitable
for erection on pole with cable clamps& earth bolt of
following size of box. (B) 250mm x 200mm x 100mm
Item Rate In
Description of Item Quantity Unit Amount
No figures
317 Supplying and erecting Street light pole bracket 11.00 Ea 491.87
comprising main B Class GI pipe of 4.2 cm/require
outside dia. complete with suitable B Class G.I. sleeve
tubing of approx. 45cms.length and suitable for
76.5mm/80mm/require size of pole top having nuts and
bolts for fixing the brackets and having spread of 0.5 mtr.
Length with 110 deg.with vertical plane and suitable
welded stiffener reducer and nipple with check nut
complete painted with one coat.of Red oxide / PU base
primer and two coats of Aluminium / PU paint. paint
with following nos of arms. [A] Single Arm bracket
318 Supplying and erecting Street light pole bracket 5.00 Ea 622.16
comprising main B Class GI pipe of 4.2 cm/require
outside dia. complete with suitable B Class G.I. sleeve
tubing of approx. 45cms.length and suitable for
76.5mm/80mm/require size of pole top having nuts and
bolts for fixing the brackets and having spread of 0.5 mtr.
Length with 110 deg.with vertical plane and suitable
welded stiffener reducer and nipple with check nut
complete painted with one coat.of Red oxide / PU base
primer and two coats of Aluminium / PU paint. paint
with following nos of arms. [B] Double Arm Bracket
319 Supplying & erecting IP 55 grade following size section 1.00 Ea. 3595.60
pillar fabricated from joint less M.S. Sheet with angle iron
legs made from jointless M.S. Angle with cable clamps to
be buried in ground to have appropriate erection to work
uniform until erected with cement concrete foundation
and 45 cm high bricks work finishing with plaster etc.
hinged double door internally supported on both side,
with internal and outside looking arrangement with look
and keys in duplicate 35 x 35 x 5 mm M.S. Angle of Two
Nos. one is welded and other with nut and bolt for
erecting Bakelite sheet. Painting the Section Pillar inside
and out side with three tank powder coated paint.
section pillar roof should be without joint with water
leakage proof & tested as per IP 55 test & followed by IS
2147 of 1962 (B) 75 X 60 X 45 cm section pillar
fabricated from 16 Gauge MS Sheet with angle iron legs
45 cm long made from 35 X 35 X 5 mm thick MS angle.
320 Supplying and erecting HYLAM sheet on existing angle 1.00 sq.mtr 1541.26
iron frame.for following thickness (D) 8mm
321 Supplying and erecting nuwood 12 mm thick on existing 1.00 Sq.Mtr 291.89
angle iron frame.
Item Rate In
Description of Item Quantity Unit Amount
No figures
322 Providing & erecting water cooler having storage 7.00 Ea. 55893.40
capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @
an ambient temp of 45˚ C. The outlet temp. of the water
should drop by 15˚C within a hour, The water cooler
should be comprising of hermetically sealed compressor,
fan motor, condensing unit, water tank surrounded by
evaporating, coil, thermostats, relay etc.complete with
necessary inlet & outlet connection. The body of water
cooler will be made from Stainless Steel.
323 Supplying & erecting reverse osmosis (RO) water 7.00 Ea. 77891.20
purification system with M.S. powder coated pedestal
frame, prefilter housing carbon filter suitable buster DC
pump, auto low & high pressure switches with following
size of LPH capacity & erected as directed [D] 100 LPH
with 1 phase / 3 phase Raw water pump of 500LPH @
2.5kg/cm2 - (1N0 - Kirloskar /CRI/Lubi), Dual media
filter 10"x54" - (1 No), Micron cartridge filter 20" x 2.5" (
1No), High pressure pump 500LPH @ 10kg/cm2 - (1No -
Shimge /CRI /Lubi), RO Membrane housing with RO
membrane of 40*40 - (1No), RO pressure tube 4" x 1E - (
1No), 0 - 1200LPH Rotameter -(2 Nos), with Recovery
324 Supplying and erecting horizontal / vertical mounting 13.00 Ea. 11455.42
type storage water heater with copper container housed
in M.S./S.S./ABS body insulated with glass wool/puff
complete with heating elements,adjustable thermostats
300C to 850C, indicating lamp, safety valve, fusible plug,
etc.complete erected with coach bolts, nuts. washers &
cementation (C)25 Ltr. with 2 KW. heating element
Premium Category
325 Supplying and erecting approved make panel mounting 7.00 Ea. 1275.63
type Digital Voltmeter having 3 digits LED display, 0 to
750 AC Volts range erected on existing panel board with
all connection, wiring etc .with manufacturers calibration
certificate.
326 Supplying and erecting approved make panel mounting 7.00 Ea. 1558.43
type Digital Ammeter having 3 digits LED display,
external CT operated, calibrated for 0 to 1000 Amps
suitable to operate on 500 Volt AC , erected on existing
panel board with all connection, wiring etc .with
manufacturers calibration certificate.
switch for 3 phase AC Supply 500 V on existing panel
board with necessary connections.
Item Rate In
Description of Item Quantity Unit Amount
No figures
328 Providing & erecting L.T. Current Transformer with bar 21.00 Ea. 274.72
primary 50/5 to 1000/5 ratio 15 VA burden erected in
existing CRCA box duly secured with insulating materials
connected to the meter
329 Supplying and erecting approved make suitable panel 21.00 Ea. 43.43
indicator LED type lamp, lens cover, complete erected
with necessary connections.
Supplying and erecting, commissioning and testing of
Diesel Generating set confirming to IS: 4722:1968 &
BS:5514 having continuous rating, 3 phase, 415 volts,
cycles A.C. supply comprising of a totally enclosed
air/water cooled diesel engine with multi-cylinders
developing suitable BHP not less than following capacity
at 1500 RPM with 10% overload for one hour in
hours with standard accessories like fly wheel,
lubricating oil cooler, "A" class governor, heavy duty fuel
wheel and lubricating oil filter, oil bath air filler,
lubricating oil pressure gauge, end exhaust manifold,
standard set of tools with adjustable spanners, screw
drivers, cylinder head to cover, joint cylinder head to
exhaust, element lube oil filter, 12 / 24 volts electric
starting equipment complete with standard heavy duty
battery, dynamo, cut-outs, ammeter, necessary wiring,
pressure gauge, starter etc and heavy duty Residential
type exhaust silencer and vertical hot air duct both
logged with asbestos rope, save oil trays, exhaust piping
of required length, standard wall/floor mounted fuel
with level indicator and piping and drip proof alternator,
self excited, self regulated, screen protected, with
excitation system, capable of delivering the rated system
output at 415 volts, 3 phase, 0.8 PF, 50 Hz, 4 wire,
running at 1500 RPM, conforming to IS-4722- 1968 with
voltage regulation +/- 5% of rated voltage from no
load to full load. Both the engine and alternator fitted on
a common fabricated steel base plate with antivibration
mounting engine and alternator both connected to
each other by flexible flange coupling and with floor/wall
mounted control panel box comprising of voltmeter
adequate capacity,
Item Rate In
Description of Item Quantity Unit Amount
No figures
330 indicator lamps duly wired with HRC fuses. The 1.00 Each 968209.23
alternator & control panel shall be connected with
provided suitable capacity armoured cable and complete
with Acoustic enclosure (canopy) made out of 16 SWG
CRCA Sheet, sound absorbing material Rockwool of
density & 100 mm thick conforming to IS:8183 / PU
Foam of 40 Density - at least 40 mm. The resin bonded
rockwool covered from inside the canopy by perforated
sheet with 3/4 mm holes, sound level not more than
dB at a distance of 1 mtr, as per PVCT norms. Erection,
commissioning and satisfactory testing as per
requirement with first filling of fuel, oil, etc. with
guarantee / Warrantee of complete system for Two
years. & with obtaining all necessary certificate from
Electrical Inspector. The Capacity and Ratings of DG sets
are as below. (L) Continuous rating of 100 KVA ,BHP not
less than 126 BHP
331 Supplying & erecting Amplifier having following 1.00 Ea 11298.87
specification:
Power Output :250W (RMS) (300W Max.)
inputs : 6 Misc. & 2 Aux.
frequency Response :50-1500HZ I3db
Tone Controls :Cut & Boost type
LED Meter :5 LED Arrays
The amplifier suitable to operate 240V A.C.& 24volt D.C.
(Battery) with automatic changeover from AC to Battery
operation, duly protected by wrong Battery Polarity
connections. [[Approved by Competent Authority i.e. not
Below the rank of Executive Engineer ]
332 Supplying & erecting Booster Amplifier having power 1.00 Ea. 9672.77
output of 25OW (RMS,), suitable to obtain combined
power output of two, with 6 mike inputs & suitable to be
used independently as a 250watt amplifier in
combination with mike & mixer. The booster Amplifier
shall be without mike &Aux. input channels, The system
shall be suitable to operate on 24OV. A.C. & 24 Volts D.C.
Battery. [Approved by Competent Authority i.e. not
Below the rank of Executive Engineer ]
333 Supplying & erecting recess wall mounting speaker with 43.00 Ea. 591.86
5W rated input power 3.3 K. Ohms / 3W impedance, 100 -
10000 Hz frequency response with 6 inch dia. cone type
8 ohms speakers duly fitted in ABS plastic cabinet of
colour match with wall or ceiling of following size.
[[Approved by Competent Authority i.e. not Below the
rank of Executive Engineer ] (b)Square shaped 260 x
260mm size speaker
Item Rate In
Description of Item Quantity Unit Amount
No figures
334 Supplying microphones stands with sturdy mechanism, 2.00 Ea 445.41
treble free movement & positioning of microphones, free
from rust with superior quality of chrome plating with
following size. [[Approved by Competent Authority i.e.
not Below the rank of Executive Engineer ] (c)Fixed
height 91 cms. & extendable up to 62 cms. with round
base of dia. 23 cms.
335 Supplying, installing and testing approved make 2.00 Ea. 1284.72
microphone for All purpose, with frequency response of
100 - 11000 Hz, having sensitivity 2.2mv / Pa &
impedance 500 Ohms (LO- Z) supplied with quick
detachable holder, 6 mtr twin core cable & 3 pin XLR
connector. [[Approved by Competent Authority i.e. not
Below the rank of Executive Engineer ]
Total Rs.
I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in figures and
words) of the estimated rate mentioned above. Amount of my /our
Tender works out as under.
Estimated amount put to tender Estimated amount put to tender
Deduct………% below Add………% Above
In words In words
The Contractor shall exhibit a board with detailed specification and details of work as directed by the
1 Engineer-In-Charge for which no extra payment shall be made.
2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.
3 Income tax TDS will be deducted at a source while making payments of bills
In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-
10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where
4 there is a change as per actual mix design the cost of difference of cement consumption have been deducted
from the rate of original item at the rate of input rate mentioned in all the tender.
Deputy Executive Engineer Executive Engineer
Vapi ( R & B ) Sub Division Valsad ( R & B ) Division
Vapi Valsad
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
BOQ.pdf
Building-Specification Booklet.pdf
GRs.pdf
NIIT.pdf
P.Q. ANS Hostel C-200 Manekpur Umargam.pdf
SBD.pdf
SPECIFICATION.pdf
MOU Electrical Work.pdf
NOMINATED ELECTRICAL SUB CONTRACTORS.pdf
SBD Specification (Electrical Work)_compressed.pdf
Special condion Electric.pdf
DWG Manekpur.pdf
CORRIGENDUM
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].