Special repairs to bldg. No RA 22/2 at RA line, Kannur Mily station under AGE (I) Cannanore.

Amount

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) mixed with water proofing compound as per manufactres instructions on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed . Note: water proofing compound shall be measured and paid seperatetly.

M&L for rendering 10mm thick in cement mortar (1:4) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

Supply only water proofing compound.

M&L for rendering 10mm thick in cement mortar (1:3) on ceiling surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for chipping the spelled and old concrete removing loosely adhering particles using wire brushes and make the structure for the application of micro concrete complete complying with standard specification including lead and lift for an average thickness of 50mm including disposal of debris outside MD land complete all as specified and directed. Note: 1. The cleaning of bar shall be in such a way that No rust shall be stick on it. 2. The removal of defective concrete shall be right round the bar, when going behind the necessary thickness

M&L for providing polymer modified mortar using cement motar 1:3 mixed with metorbond cement modifier cum bonding agent @ 5 ltr per bag of cement or using SBR liquid 5% by weight of cement or as per manufactures instructions. The repair shall be carried out in already prepared surface (i.e chipping and reinforcement priming) where the application of Renderoc RG/Emcekrete fluid mico concreting is not possible. The prepared mortar shall be applied for an average thickness of 30 mm after and including application of Nitobond EP, in any case HS epoxy or equivalant bonding agent to the cement concrete mortar complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removing debris outside MD land all as directed.

M&L 25mm thick PCC 1:2:4, Type B1 (using 20mm graded stone aggregate) as in flooring and finished fair and even all as specified and directed.

M&L for vitrified ceramic tiles, polished, 10mm to 12mm thick, area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:4) all as specified and directed.

M&L for coloured joint free non-skid ceramic tiles, 7mm to 8mm thick, area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:4) all as specified and directed.

M&L for coloured glazed ceramic tiles 450x350x7mm thick, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

Demolition of cement concrete (reinforced) in any description, in any position not otherwise specifically provided for, and removing debris outside MD land all as directed.

M&L Reinforced cement concrete (1:1.5:3), type A1, (using 20mm graded stone aggregate) nominal mix as in beams, lintel over 1.5m span all as specified and directed. Note : Reinforcement and form work shall be measured and paid separately.

S&F CRS (TMT) bars 10 mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips all as specified and directed.

S&F CRS (TMT) bars 6 to 8mm dia as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips all as specified and directed.

All as per Sl item No 16 above, but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders all as specified and directed.

M&L for use and waste of form work to sides and soffits of lintel, beams etc rough finished surface of concrete all as specified and directed.

Demolition of brick or stone / boulder masonry built in cement or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris outside MD land all as directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, 10cm thick with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:4) complete all as specified and directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, exc.10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and directed.

Taking up or down steel tubing and connecting including cleaning for removing to store of sizes upto 20mm bore all as directed.

S&F for 15mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings or in floors etc. all as specified and directed.

S&F for 20mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed to wall/ceiling or on floor all as specified and directed.

S&F in repair stainless steel drapery rod 25mm dia incl side caps with brackets fixed to wall with suitable brass screws all as directed.

S&F in repairs bib tap 15mm dia, chromium plated, fancy type, cast copper alloy, screwed down, screwed for iron pipe or ferrule and complete all as directed.

S&F in repair 15mm pillar taps, fancy type, cast copper alloy with capstan heads, chromium plated , screwed down high pressure ,with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed all as specified and directed.

S&F in repairs 15 mm dia angular stop cock fancy type cast copper alloy chromium plated screw down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as directed by Engr-in-Charge.

Supply and fix PVC connecton 60cm long with PTMT nuts for flush tank, wash basin, etc. all as specified and directed

S&F in repairs stainless steel plate rack of 1mm thick (for kitchen), of overall size not less than 90cm x 90cm x 20cm of standard pattern/ design and weight not less than 6.50 Kg each all as specified and directed.

S&F in repair chromium plated brass wall mixer single lever high flow bath and shower mixer (concealed body) wall mounted model fixing to 15mm dia pipe all as specified and directed.

S&F chromium plated brass Health faucet (Jet Spray), 15mm dia with flexible LDPE pipe with jet of 100 mm long on one end and socket joint of 15 mm dia on other end, nozzle of jet shall be chromium plated complete fixed in repairs all as specified and directed.

M&L for 75mm diameter PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed.

S&F PTMT grating square 150mm size , setting and jointing with solvent cement all as specified and directed.

M&L PVC (SWR) pipe type 'B' 75mm bore single socketed with solvent cement joints laid in trenches or in floors all as specified and directed.

S&F 75 mm bore, PVC (SWR) bend with access door any radius all as specified and directed

Dismantling of cast iron or RCC drain pipes, jointed in cement mortar and taking out of trenches all as directed.

S&F in repair Vitreous China Wash basin, white, flat back, size 580 x 450 mm, including CI brackets, (but excl. pillar tap) cutting for and pinning in ends of brackets or erecting stand and fixing of waste pipe etc complete all as specified and directed.

S&F Vitreous China Wash down water closet pan (Pedestal pattern) white, (excluding flushing cistern and flush type) pedestal pan and trap including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc complete including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device as fixed in repairs all as specified and directed.

S&F for PVC valveless, syphonic action type flushing cistern low level, 10 Litre capacity, white, with inlet, ball valve, float and handle including flush pipe all as specified and directed.

S&F prelaminated particle board of 12mm thick exterior grade pre laminated both sides with decorative choice laminations fixed with screws as in kitchen cup board shutters and shelves and pelmet boxes etc including removing old shutters complete all as specified and directed by Engineer-in-charge Make: Eco Board/Greenlam/Century

S&F Continuous (Piano) hinges, mild steel, bright finish or electrogalvanised, 30mm width of flap (when open) all as specified and directed.

Taking down chowkats with shutters exc. 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) and refixing in same opening all as directed.

Taking down chowkats with shutters n exc. 1.5 Sqm each (without taking off shutters from the frame) all as directed.

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

All as per item No 46 here in before but for with transoms and mullions, with double rebated on the solid frame for fixing double shutters all as specified and directed.

M&L for mild steel flat iron of size 25 x 3mm for holdfasts for securing new wooden frames and similar articles conforming to Fe-290 Gde-E-165 all as specified and directed.

M&L for PCC 1:2:4, type B1 using 20mm graded stone aggregate for fixing hold fast, coping, bed block etc including necessary form works all as specified and directed.

M&L for second class hardwood, panelled shutter 30mm thick (two panel) with lock rail and panel of 9mm BWP, 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

S&F 30mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc; (with out sash bars), edges of framing, fitted with cut and mitered beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a) all as specified and directed.

S&F Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge.

Supply and fixing 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge.

S&F cast iron (malleable) Casement stays, size 300mm, with hinged joint and two plates with studs complete all as specified and directed.

S&F stainless steel butt hinges medium weight; 75mm size all as specified.

S&F stainless steel butt hinges medium weight; 100mm size all as specified.

S&F 200mm long aluminum anodized barrel tower bolts of extruded section all as specified.

S&F 100mm long aluminum anodized barrel tower bolts of extruded section all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 150mm size all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 100mm size all as specified.

S&F 4mm thick plain sheet glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane all as specified and directed.

S&F 4mm thick frosted glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

S&F in repairs Netlon wire mesh (Good quality ) for fly proofing complete all as specified and directed.

S&F for second class hard wood, plain fillets, square, rectangular or triangular in section, clean sawn, sectional area exc.6 & n. exc. 13 sqcm secured with nails or brads all as specified and directed.

S&F 1000 litres capacity rotational moulded polthylene water storage tanks(cylindrical vertical with closed top) of make Sintex/Polycon/Plasto hoisted and fixed in position including taking down unserviceable water tank all as specified in SSR Part I,2009 and directed.

M&L for complete removal of existing treatment on surfaces of wall and applying one coat of wall primer (water thinable / solvent thinable) , two coats of acrylic wall putty for making the surface smooth and even including sanding each layer to receive next new layer, one coat of wall primer and applying two coats of tractor emulsion oil emulsion distemper to be applied by approved applicator of the manufacturer of the paint and all as specified and as approved all as specified and as directed.

M&L for preparation of new surfaces of walls and applying two coats of acrylic wall putty for making the surface smooth and even including sanding each layer to receive next new layer and applying one coat of wall primer(water thinnable/solvent thinnable), applying two coats of oil emulsion distemper by approved applicator of the manufacturer of the paint and all as specified and as approved all as specified and directed.

M&L for preparation of new surfaces of ceiling and applying two coats of acrylic wall putty for making the surface smooth and even including sanding each layer to receive next new layer and applying one coat of wall primer(water thinnable/solvent thinnable), applying two coats of oil emulsion distemper by approved applicator of the manufacturer of the paint and all as specified and as approved all as specified and directed.

M&L for complete removal of existing treatment on surfaces of wall and surfaces and applying two coats of cement base paint over a coat of primer on walls surfaces all as specified and directed.

M&L for preparation of new plastered surfaces and applying 2 coat of cement base paint over a coat of primer on walls surfaces all as specified and directed.

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer all as specified and directed.

M&L preparing old wooden surfaces of any description over 10 cm width or girth and applying a coat of synthetic enamel painting all as specified and directed.

M&L for hard core of guage n.exc 63mm broken stone or boulders, deposited, spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface all as specified and directed

M&L 75mm thick PCC 1:3:6 Type C2 (using 40mm graded stone aggregate) as in plinth protection including necessary form works all as specified and directed.

M&L for framed work such as ornamental and intricate design in grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as specified and directed.

Dismantling structural steel work incl doors, gates but excluding framed truss etc complete all as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc complete all as directed.

M&L for structural steel work in tubular trusses including special shaped washer, two coats of synthetic enamel paint over a coat of primer etc, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240 all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

LAKSHMI BUILDERS

T.P.SUNIL KUMAR

JEETH CONSTRUCTION