PROVN OF COVER SHED AND MISC WORK SERVICES AT BRD UNDER GE (AF) MC CHANDIGARH

Amount

Excavating in post holes (or similar holes) each n exc 0.5cum, getting out in soft/loose soil, and removing surplus soil to a distance n exc 50m and making good bottom surface by watering and well ramming, complete all as specified and directed.

Material and labour for plain cement concrete (1:4:8) type D-2 using 40mm graded crushed stone aggregate, as in foundation filling and mass concrete, complete all as specified and directed.

Supply and fixing Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes as in verticle posts, trusses, purlin (beam, tee, angle, channel) conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

S&F Pre painted Coloured Galvalume roofing system sheet 0.50 mm thick, corrugated sheet having Zinc aluminum alloy coating AZ150 shall be as per IS:277/ASTM 1379 150 gsm/ sqm double ribbed trapezoidal profile steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws, complete all as specified and as directed. Note:- (i) The manufacturer's test certificate and individual test certificate for the chemical and mechanical properties of sheet must be submitted for approval by the concerned authority prior to installation. (ii) The contractor shall ensured that no leakages take place from the roof. The roofing shall be Coloured Galvalume roofing system (olive green colour or as approved by GE) with feed material manufactured from 0.50 mm Total coated thickness (TCT), minimum 550 MPa yield strength and shall conform to the physical specifications of IS: 2062 of 2011, coated with hot dip metallic Aluminium / Zinc alloy coating AZ150 as 150 gm/sq.mt total on both sides. (iii) The painting shall be coloured baked enamel polyester with silicon coating of film thickness 25 microns nominal on the exposed face/exterior side and on the reverse side ( interior face) shall be white with 15 microns film thickness, over a coat of 5 micron nominal thickness Primer. (iv) The contractor shall produce purchase vouchers for each lot for verification of Engineer-in-Charge. Make:- M/s Tata Blue scope/Jindal/Bhusan

Material and labour for applying two coats of synthetic enamel paint over and including a coat of red oxide primer, on new steel surfaces over 10cm width or girth, including preparation of steel surface, complete all as specified and directed.

M&L for Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre deep for laying/taking out of cables and foundation of poles etc. and getting out, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in soft/loose soil after construction work in foundation, complete all as specified and directed.

Removal of surplus excavated soil to a distance not exceeding 50metre and depositing where directed at a level not exceeding 1.5metre above the starting point, complete all as specified and directed.

Material and labour for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:4), complete all as specified and directed.

M&L for rendering 15 mm thick on brick/concrete surfaces in cement mortar (1:4) using liquid water proofing compound as per manufaturer instruction finished even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid seperately.

M&L for rendering 15 mm thick on other than fair faces of brick surfaces or concrete surface in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound, ISI marked complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of cement base paint , complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer over a thin layer of wall care putty , complete all as specified and directed.

Material and labour for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed.

Supply and fixing 12mm size wire netting of stainless steel wire 1.4mm dia fixed with tinned tacks of stainless steel wire staples, complete all as specified and directed.

Material and labour for 12mm thick toughened glass door (size 0.76mx2.2m) and glass partition (size 5.74mx2.2m) for squash court back wall with all necessary fittings/supports (No of Support -04 and size 0.30mx2.20m) with using high strength nylon or aluminium as required for international squash court including all necessary civil work as required at site, complete all as specified and directed. (a) Glass top fittings comprises:- Hinges-02 Nos, L- block - 02 Nos, C-block-01 No, Angles - 08 Nos, M-6 Allen Key bolt -42 Nos, Dom nut-42 Nos, PVC cap -42 Nos (b) Glass bottom fittings comprises :- Aluminium Top plate -04 Nos, Aluminium angles- 08 Nos, MS base plate- 04 Nos, washers -24Nos, M-16 Nuts and bolts-12 Nos, Anchor fastener with washer length 6 inch - 16 Nos, rubber bush - 12 Nos, bolts 3/8 inch dia and length 2 inch - 08 Nos, glass, aluminium lock etc. Note:- (i) The work shall be executed by an ISO certified company directly having minimum experience of 3 works similar nature in past three years. (ii) Manufacturer conforming to the world squash court federation (WSF) standard specification. (iii) Tenderers is advised to visit the site for this item before quoting the rates with prior approval of Engineer-in-Charge.

JP ENTERPRISES