C/O fruit processing unit at Dhaulakuan in Tehsil Paonta Sahib, District Sirmour H.P. (SH- C/o Main building portion, boundary wall, water supply and sanitary installation, septic tank with soak pit and rain water harvesting tank)

Amount

Excavation in foundation and trenches in earth work in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the Engineer -in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (To be arranged by the contractor) as per satisfaction of Engineer- in -charge through all modes of transportation including head load ,animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour ( if required ). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation and used /removed as per the direction of the Engineer - in- charge. Any loss to the public and private propriety during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respect including all incidental charges.

Excavation in earth work in drains & channels in all heights & depths in all kinds of soils, including saturated soils comprising of pick work, jumper work & blasting work both in soft & hard & wedging out of rock ( Where blasting work is prohibited ) & their intermediate classification of soils including dewatering wherever required, setting out to required lines, grades, side slopes,trimming bottom & levels as shown on the drawing & as directed by the Engineer-in-Charge at site, according to the HP.PWD. specification of and sorting out useful unuseful materials & stacking the same in all leads,lifts & levelling & disposing of surplus excavated earth in acquired width of road or on approved dumping sites which will be arrang by the contractor at his own level & dumping charges if levied will be born by the contractor through all modes of transportation & used/ removed as direction of Engineer-in-Charge including head load, animal load or mechanical means alongwith its levelling fine dressing & all labour, machineries, materials tools equipments & safet measured & incidential necessary to complete the work by mechanical means and labour ( if required ). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation and used /removed as per the direction of the Engineer - in- charge. Any loss to the public and private propriety during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respect including all incidental charges.

Dressing the ground including cutting & filling upto 15 cm ( fifteen centimetre ) in all kind of soil including carriage of all labour equipments & materials to various location through all leads, lifts & other incidential charfges complete as per entire satisfaction of the Engineer-in-Charge.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including carriage of materials through all modes of transportion with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-charge.

Providing form work with steel plates 3.15mm. (Three point fifteen milimetre) thick welded with angle iron in frame 30X30x5mm.(Thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden/ steel battens and ballies, height of propping and centring below supporting floor to ceiling to any floor height and removal of the same for in situ-reinforced concrete and plain concrete work and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

In foundation, footings, bases of columns etc. and mass concrete.

In flat surfaces such as soffits of suspended floors, roofs, landings and the like of any thickness in all floor level in all heights.

Columns,pillars,posts and struts Square,rectangular or polygonal in plan in all floor level in all heights.

Beams, Cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels in all floor level in all heights.

Stair cases with sloping or stepped soffits excluding landing in all floor level in all heights.

Edges of slabs and break in floors and walls in any width.

Vertical surfaces such as walls ( any thickness ) partations & the like includinbg attached pillasters, buttresses, plinth & string courses & the like.

Providing and laying cement concrete 1:4:8 (One cement: Four sand :Eight graded cursed/broken stone aggregate 40mm (forty millimeters) nominal size) mechanically mixed and curing complete, excluding cost of form work in foundation and plinth including carriage of materials through all modes of transportion with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-charge.

Providing and laying reinforced cement concrete 1:2:4 (1 cement : 2 Sand : 4 graded stone aggregate 20mm nominal size) to give a smooth and even surface including centring and shuttering etc. but excluding cost of reinforcement in string courses, copings, bed plates, anchor blocks, plain windows sills and the like in all floor level in all heights including carriage of materials through all modes of transportion with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-Charge

Providing and laying cement concrete 1:1.5:3 (one cement isto one point five sand isto three crushed stone aggregate 20mm. (Twenty millimeter) nominal size) mechanically mixed and vibrated, curing complete excluding cost of form work and reinforcement for reinforced concrete work and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

In Foundation, footings bases of columns etc. and mass concrete.

In suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto floor all level in all heights.

In stair cases with sloping or stepped soffits excluding landings in all floor level in all heights.

In columns, pillars, posts and struts. Square, rectangular or polygonal in plan, in all floor level in all heights.

Wall ( any thickness but not less than 0.10 mtrs ( Zero point one zero metre ) attached pillasters buttresses, plinth & string courses etc. from top of foundation level upto all floor level.

Providing & laying cement concrete mechnically mixed upto all floor level reinforced cement concrete 1 : 2 : 4 ( one cement : two sand : four graded stone aggregate 20mm ( twenty milimeter ) nominal size ) to give a smooth & even surface including centring & shuttering etc. but excluding cost of reinforcement in moulding as in cornices windows sills etc. not exceeding 15 cm ( fifteen centimetre ) in grith as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & laying cement concrete work mechnically mixed 1: 2 : 4 ( One cement : two approved sand : four graded crushed stone aggregate 20mm ( twenty milimeter ) nominal size ) reinforced concrete chajja of any thickness upto floor all level including finishing the exposed surface with cement mortar 1:3 ( One cement : three approved sand )to give a smooth & even surface centring/form work & curing complete excluding the cost of reinforcement including carriage of materials within all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge as per HP.PWD., specification 1990 Volume- I ( One ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing Tor / TMT steel reinforcement of TATA Tiscon/SAIL/Rashtria Ispat incluiding cost of binding wire for R.C.C. work including cutting, bending, binding and placing in position complete in all floor levels in all heights including carriage of materials through all modes of transportations with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-Charge.

Brick work using common burnt clay building bricks in foundation and plinth in Cement Mortar 1:6 (One cement : Six sand) Second Class Bricks including carriage of materials through all modes of transportion with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-Charge.

Providing and laying brick work using common burnt clay building brick in Cement Mortar 1:6 (One cement:Second sand) Second class bricks in super structure for all floors levels and in all heights including carriage of materials through all modes of transportations with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-Charge.

Providing and laying second classs half brick masonry in common burnt clay building bricks in foundation and plinth level in Cement Mortar 1:4 (One cement: Four sand) including carriage of materials through all modes of transportion with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-charge.

Providing and laying second class half brick masonry in common burnt clay building bricks in cement Mortar 1:4 (One cement: Four sand) in super structure for all floor levels in all heights including carriage of materials through all modes of transportations with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-charge.

Stone soling tightly hand packed under floors, including watering, ramming and consolidating complete and carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing 100 mm ( One hundred milimeter ) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing bright finished hard drawn hooks & eyes 150 mm ( one hundred fifty milimeter ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing 40 mm ( forty milimeter ) thick second class deodar wood work for panelled glazed or panelled & glazed shutters for doors, windows & clerestory windows including black enamelled iron butt hinges with necessary screws as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing 40 mm ( forty milimeter ) thick second class deodar wood work for wire gauge shutters using galvanised mild steel wire gauge of I.S. gauge designation 85G wire pof dia 0.56 mm ( Zero point five six milimeter ) for doors, windows & clerestory windows including bright finished black enamelled iron butt hinges with necessary screws as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing Chamfered edge core fillets beading 40 x 12 mm ( forty into twleve milimeter ) section in doors of first class deodar wood as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing 19 mm ( nineteen milimeter) thick commerical board shutters for shelves/ box for cub board with butt joints & fixing with nails & screws etc. including fixing with nickel plate piano hinges with screws etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing 19 mm ( nineteen milimeter ) thick commerical board water proof shutters for cub board including fixing with nickel plated piano hinges with screws etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing 1.00 mm ( One milimeter ) thick coloured or plain lamination sheet ( Sunmica ) on boards/ ply wood sheet with approved adhesive & nail etc. complete within all leads and lifts, as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing First class Deodar wood for square edges cover fillets ( beading ) 19 mm x 6mm ( nineteen milimeter into six milimeter ) section including mitring at junctions with wood screws & nail complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing bright finished brass furniture handles as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing bright finished brass ball catcher 10 mm ( ten mililmeter ) dia as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing oxidized mild steel sliding door bolts with nuts & screws etc. complete 300 x 16 mm ( three hundred into sixteen milimeter ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing oxidized mild steel sliding door bolts with nuts & screws etc. complete 250 x 16 mm ( two hundred fifty into sixteen milimeter ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing aluminium tower bolts ( barrel type ) anodized transparent or dyed to required shade & colour with necessary screws etc. complete 200 x 10 mm (two hundred into ten milimeter) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing aluminium handles anodized transparent or dyed to required colour shade with necessary screws etc. complete 125 mm (One hundred twenty five milimeter) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing aluminium handles anodized transparent or dyed to required colour shade with necessary screws etc. complete 100 mm (One hundred milimeter) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing anodized aluminium fan light catch with necessary screws complete as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing 300mm ( three hundred milimeter ) long anodized a;uminium chain for fan light catch including necessary screws etc. complete as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing 150 mm ( One hundred fifty milimeter ) size bright finished brass haeps & stapples ( safety type )_ with necessary screws etc. complete as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing over head hydraulic door closer of approved brand & manufacture conforming to IS specification ISI marked ) for door with screws complete as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing mild steel plain grills of required pattern in steel windows frame etc. with mild steel flat 20 x 55 ( twenty intofive milimeter ) and 8 x 8 mm ( eight into eight milimeter ) mild steel square in combination with or by screws distance between bars should be not be more than 150 mm ( one hundred fifty milimeter ) centre to centre total grills unit should be fixed to windows frames as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing 3mm ( three milimeter ) thick Aluminium composite panel ( ACP ) tiles ceiling 600 x 600 mm ( Six hundred into six hundred milimeter ) in flase ceiling upto all height over ready made powder coated metal sheet of approved quality of ISI marked including fixing to alumninium frames 600mm ( six hundred milimeter ) centre to centre grid suspended from truss complete in all respect as per Archetectural drawings as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing 65 x 35 mm ( sixty five into thirty five milimeter ) special quality bright finished brass cub board locks or wardrobe locks with six levers including necessary screws etc. complete ( Indian make of ISI marked/aproved quality ) as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & laying marble work ( Table rubbed and polished ) in flooring 20mm ( twenty milimetre ) thick base in cement mortar 1:3 ( one cement : three approved sand ) including jointing with cement mortar 1:2 ( One cement : two marble dust ) with an admixure of pigment to match the shade of the marble. 20mm ( twenty milimetre ) thick white Makrana marble having grey streaks upto 2.05 mtrs. height as per HP.PWD.,specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

First class white/coloured glazed tiles in skirting,risers & dedo of Nitco, Kajaria / Orient etc. or equilevent of approved shade 12 mm ( tweleve milimeter ) thick cement mortar 1:3 ( One cement : three approved sand ) & jointed with cement slurry finished with flush pointing in white cement as per HP.PWD.,specification 1990 Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & laying Spartic ceremic tiles ( 30 x 30 cm ) ( thirty into thirty milimeter )of approved shade tiles 5.5 mm ( five point five milimeter ) thick in flooring, treads of steps laid on a bed of 12 mm thick cement mortar 1 : 3 ( One cement : three sand ) finished with flush pointing in white cement as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & laying 10 mm ( Ten milimeter ) thick anti skid water proof stain & impect resistant heavy duty vetrified tiles on Nitco or equivalent 600 x 600 x 10 mm ( six hundred into six hundred into ten milimeter ) manufactured of approved shade & colour in flooring, treads of steps and landings laid over 12 mm ( twelve milimeter ) thick cement mortar 1 : 3 ( One cement :three sand ) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & laying red stone slab flooring 40 mm ( forty milimeter ) average thick on 20mm ( twenty milimeter ) average thick base of cement mortar 1 : 4 ( One cement : four sand ) laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & granite polish finish complete as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entiresatisfaction of Engineer-in-Charge.

Providing & laying 50 mm ( fifty milimeter ) thick cement concrete flooring with metallic concrete hardner topping under layer of 35 mm ( thirty five miklimeter ) thick cement concrete 1 : 2 : 4 ( One cement : two sand : four graded stone aggregate 20 mm ( twenty milimeter ) nominal size ) & top layer of 15 mm ( fifteen milimeter ) thick metallic concrete hardner consisting of mix 1 : 2 ( One cement hardner mix : two stone aggregate of 6 mm ( six milimeter ) nominal size ) by volume with which metallic hardening compound of approved quality is mixed in the ratio 4 : 1 ( four parts of cement : one part of metallic floor handening compound of approved quality by weight ) including finishing complete as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entiresatisfaction of Engineer-in-Charge.

40mm ( forty milimeter ) thick cement concrete flooring 1:2:4 ( One cement : two approved sand : four graded stone aggregte 20mm( twenty milimetre ) nominal size ) laid in one layer finished with a floating coat of neat cement in all floor level as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entiresatisfaction of Engineer-in-Charge.

15 mm ( fifteen milimeter ) thick cement plaster skirting ( Upto 30 cm ( thirty centimeter ) height ) with cement mortar 1 : 3 ( One cement : three sand ) finished with a floating coat of neat cement including rounding of junction with floor as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entiresatisfaction of Engineer-in-Charge.

Providing and laying 25 mm (Twenty five milimetre) thick Mirror Polished Kota stone slab flooring with 20mm (twenty milimetre ) thick base of cement mortor 1:4 (one cement is to four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying 25mm (twenty five milimetre ) thick Mirror polished Kota stone slab in risers of steps ,skirting dado and pillars laid on 12 mm (average) thick cement morter 1:3 (one cement isto three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

6mm ( six milimetre ) cement plaster to ceiling with cement mortar 1:3 ( One cement : three approved sand )as per HP.PWD., specification 1990 Volume-I ( one )including carriage of all labourequipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15mm ( fifteen milimetre ) cement plaster in single coat on rough side of brick/ concrete/ stone walls of interior plastering upto floor two level including arrises,internal rounded angles, chamfers & rounded angles not exceeding 80mm in ( eighty milimetre ) grith finished even and smooth in cement mortar 1:6 ( One cement : six approved sand) as per HP.PWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15mm ( fifteen milimetre ) cement plaster in single coat on rough side of brick/ concrete/ stone walls of interior plastering upto floor two level including arrises,internal rounded angles, chamfers & rounded angles not exceeding 80mm in ( eighty milimetre ) grith finished even and smooth in cement mortar 1:5 ( One cement : five approved sand) as per HP.PWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15mm ( fifteen milimetre ) cement plaster in single coat on fair side of brick/ concrete/stone walls of interior plastering upto floor two level including arrises,internal rounded angles, chamfers & rounded angles not exceeding 80mm in ( eighty milimetre ) grith finished even and smooth in cement mortar 1:6 ( One cement : six approved sand) as per HP.PWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15mm ( fifteen milimetre ) cement plaster in single coat on fair side of brick/ concrete/stone walls of interior plastering upto floor two level including arrises,internal rounded angles, chamfers & rounded angles not exceeding 80mm in ( eighty milimetre ) grith finished even and smooth in cement mortar 1:5 ( One cement : five approved sand) as per HP.PWD., specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15mm (fifteen milimetre)cement plaster in single coat on fair side of brick/ concrete/ stone walls of interior plastering upto floor two level including arrises,internal rounded angles, chamfers & rounded angles not exceeding 80mm in (eighty milimetre) grith finished even and smooth in cement mortar 1:4(One cement:four approved sand) as per HP.PWD., specification volume-I (one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing and fixing on wall face150mm ( One hundred fifty milimeter ) dia PVC rain water pipes of working pressure not less than 4.5 Kg ( Four decimal five kilogram ) per square meter including filling the joints with approved adhesive complete as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing on wall face PVC ( D-Plast ) accessories for rain water pipes including filling the joints with approved adhesive complete as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

PVC Plain bend 150 mm ( One hundred fifty milimeter ) dia

PVC conner type bend 150 mm ( One hundred fifty milimeter ) dia

PVC shoe150 mm ( One hundred fifty milimeter ) dia

PVC off set 45 degree 150 mm ( One hundred fifty milimeter ) dia

Providing & fixing PVC clamps ISI marked approved design with steel screws & rawal plugs etc. complete 150 mm ( one hundred fifty milimeter ) dia as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing and fixing 0.60mm ( Zero point six zero milimeter ) thick prepainted steel sheet of TATA DURASHINE in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets of TATA Durashine in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete as per HP.PWD., Specifications of 1990 volume-I includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.

Providing and fixing valley 90 cm overall 0.60mm thick prepainted steel sheet of TATA Durashine in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete as per HP.PWD., Specifications of 1990 volume-I includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.

Providing and fixing flushing 38cm overall with 0.60mm thick prepainted steel sheet of TATA Durashine in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia meter & prepainted G.I. limpet & bitumen washers complete as per HP.PWD., Specifications of 1990 volume-I includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.

Providing & fixing M.S. B.P. sheet 2mm ( Two milimetre ) thick in eaves board/facia/ soffits/ ceiling including cutting fixing & welding to steel roof mambers and applying a coat of red lead primer complete ( Base member of steel work shall be measured & paid for separately ) as per HP.PWD., specification Volume-I ( one ) including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing thiclk 15cm ( fifteen centileter ) wide & minimum 45cm ( forty five centimeter ) over all semicircular plain galvanised iron steel sheet of TATA Durashine gutter with iron bracket 40 x 5 mm ( forty into five milimeter ) size bolts and nuts and washers etc. including making conection with rain water pipe complete as per design 0.63 mm ( Zero point six three milimeter ) including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing angle iron door, windows,clerestory windows frame manufactured from steel iron section of 40x40x6mm(forty into forty into six milimeter ) & Mild steel flat 50x4mm( Fifty into four milimeter ) incombination welded together to make one frame including hinges, jamb,lock jamb,beed and if required angle thrashold of mild steel angle 50x25mm ( Fifty into twenty five milimeter ) welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel butt hinges 2.5mm ( two point five milimeter ) thick with provision of locking arrangement & shock absorber as specified & applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in Charge as per HP.PWD.,specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing in position collapsible steel shutters with vertical channels 20 mm x 10 mm x2 mm ( twenty milimeter into ten milimeter into two milimeter ) and braced with flat iron diagonals 20 mm x5 mm ( twentymilimeter into five milimeter ) size with top & bottom rails of T-iron 40 mm x 40mm x 6 mm ( forty milimeter into forty milimeter into six milimeter ) with 38 mm ( thiorty eight milimeter ) dia steel pulley complete with bolts & nuts locking arrangements, toppers, handles including applying a priming coat of red lead paint as per HP.PWD.,specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Supplying & fixing rolling shutters of approved make made of 80mm x 1.25 mm ( Eighty milimeter into one point two five milimeter ) mild steel laths interlocked together through their entire length & jointed together at the end by end locks mounted on specially designed pipe shaft, with brackets side guides & arrangements for inside & outside locking with push pull operation complete but excluding the cost of the top cover and spring, shutters having width 3.50 mtrs. ( Three point five zero metres )& above as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing 27.5 cm ( Twenty seven point five centimetre ) long wire spring grade No. 2 ( Two ) for rolling shutters as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing top cover for rolling shutters, shutters having width 3.50 mtrs ( Three point five zero metres ) & above as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing Mild steel Channels in doors,windows frames,manufactured from Mild steel channels section of size 75 x 40mm ( Seventy five into forty milimetre ), M.S. flat 75x4mm ( Seventy five into four milimetre ) combination as per design drawing including hinges, Jambs,beed & if required angle thrashold of mild steel angles,lugs with split end tails to each jamb including steel nuts hinges 2.5mm thick with provision of locking arrangement & shock observers & specified and applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in-Charge as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing steel glazed doors,windows & ventilators of standard rolled steel Z section with horizontial & vertical sashbar of angle iron ( 25x25x3mm ) ( Twenty five into twenty five into three milimeter ) T-section ( 25x25x 3mm ) ( Twenty five into twenty five into three milimeter ) in fixed and openable shutters as per standard Architectural drawing,jointed mitred & welded with mild steel Channel framed or with fixing clips or with bolts & nuts as required & iron fitting, including providing & fixing of glass pans with glazing clips & special metal sesh putty of approved make complete including applying a priming coat of red lead paint as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Steel window fixed steel windows.

Steel windows side Hung windows.

Steel ventilators Top hung ventilators

Providing & fixing MS round holding down or anchor bolts with nuts and washers plates complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing angle iron Cup-board frames manufactured from mild steel angle iron section of 25 x25x5mm ( Twenty five into twenty five into five milimeter ) thickness including hinges, jamb, lock jamb, beed and if required angle thrashold of mild steel angle 25x25mm ( twenty five into twenty five milimeter ) welded or rigidly fixed by mechanical means, lugs with fixed by mechanical means, lugs with split end tails to each jamb including steel butt hinges 2.5mm ( two point five milimeter ) thick with provision of locking arrangement and shock absorber as specified & applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in-Charge as per HP.PWD.,specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing moulded hand rail of mild steel hollow pipe 50 mm ( fifty milimeter ) dia welded in stright length over mild steel flat at top of vertical batuster including one coat of red ocide priming coat complete ( mild steel flat & baluster of railing shall be measured & paid for separately ) as per HP.PWD.,specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing steel work of TATA SALT or RASHTRIYA ISPAT welded in built up sections/hollow section in trusses and framed work, including cutting,hoisting , fixing in position and applying a priming coat of red lead paint complete as per HP.PWD., Specifications of 1990 volume-I includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.

In trusses & trussed purlins in building .

In gratings, framed, guards, bars ladders and railing, brackets and similar works.

Providing & fixing mild steel fan clamp type-I of 16 mm ( sixteen milimeter ) dia Mild steel bar bent to shape with hooked end in reinforced cement concrete slab during laying including painting the exposed portion of loop, all as per standard design complete as per specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Painting two coats ( excluding priming coat ) on new wood & wood based surface with enamel paint to give an even shade including cleaning the surface of dirt, dust & other foreign matter sand papering & stopping with enamel paint other than white as per HPPWD specification 1990 Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Applying priming coat over new wood & wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt & other foreign matter, sand papering & knotting ready mixed paint brushing primer pink as per HPPWD specification Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Painting two coats ( excluding priming coat ) on new steel & other metal surface with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust & other foreign matters with enamel paint other then white as per HPPWD specification 1990 Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Applying one coat of Birlawhite wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Applying one coat of Acrylic primer/ Asian primer or its equivelent of superior quality on new concrete/ plastered surfaces after & including preparing the surface by thoroughly brushing the surface free from mortar drops, dust,loose materials and other foreign matter sand papering smooth the surface complete as per HP.PWD., specification Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Finishing wall with weather proof exterior grade premium emulsion of Asian paints/Apex Ultima or its equivelent of approved shade on undecorated wall surface ( two coats ) to give an even shade & final finish after thoroughly cleaning the surface to remove all dirt, dust & other foreign matter etc. including sand papering smooth in all external plastered surfaces as per HP.PWD., specification 1990 Volume-I ( one )including carriage of all labourequipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & applying/ finished with proper treatment of Dr. Fixit ( Pidilite ) as per HP.PWD., specification 1990 Volume-I ( one )including carriage of all labourequipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground completeas per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing plinth protection 50mm (fifty millimetres) thick in cement concrete 1:3:6 (one cement : three sand: six crushed stone aggregate 20mm (twenty millimetres) nominal size) as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Constructing course rubble hammer dressed " U " shape open surface drain with side wall 15x22 cm(fifteen into twenty two centimetre) in cement mortar 1:6 ( one cement : six approved sand ) & inside plastering with cement plaster 1 : 3( One cement : three approved sand ) including earth work & laying 10cm ( ten centimetre ) cement concrete in 1:5:10 ( One cement : five approved sand : ten graded stone aggregate of 40mm( forty milimetre) nominal size ) & 7.5cm ( Seven decimal seven milimeter )cement concrete 1:2:4 ( one cement : two approved sand : four graded stone aggregate of 20mm ( twenty milimetre )nominal size ) & finished with floating coat of neat cement complete as per standard design as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & laying in trenches, galvanised mild steel tubes ( Medium grade ) , tube fitting ( earth work in trenches to be measured & paid for separately ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15 mm ( Fifteen milimetre ) nominal bore

20 mm ( Twenty milimetre ) nominal bore

Providing & fixing to wall ceikling & floor galvanised mild steel tubes ( Medium grade ) tube fitting & clamps including making good the wall & ceiling & floor including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15 mm ( Fifteen milimetre ) nominal bore

20 mm ( Twenty milimetre ) nominal bore

Fixing water metre stop cock in galvanised mild steel tube including necessary fitting such as mild steel galvanised jam nuts,sockets, etc. cutting & making long screws, complete ( Water metre & stop cock to be measured & paid for separately) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15 mm ( Fifteen milimetre ) nominal bore

Providing & fixing PVC water storage tank of ISI 12701 marked,G.I. inlet & outlet connection, 15mm nominal bore ball valve & mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level 1000 litre ( One thousand litre ) net capacity tank as per HP.PWD., Specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing and fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

150mm (One hundred fifty milimetre ) dia

110mm (One hundred ten milimetre ) dia

90mm ( Ninety milimetre ) dia

Providing & fixing PVC door bend with oval access door insertion rubber washers 3mm ( three milimeter ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

150mm (One hundred fifty milimetre ) dia

110mm (One hundred ten milimetre ) dia

90mm ( Ninety milimetre ) dia

Providing & fixing PVC Plain bend ISI marked including fixing with approved adhesive etc. complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

150mm (One hundred fifty milimetre ) dia

110mm (One hundred ten milimetre ) dia

90mm ( Ninety milimetre ) dia

Providing & fixing PVC collars ISI marked including fixing with approved adhesive etc. complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

150mm (One hundred fifty milimetre ) dia

110mm (One hundred ten milimetre ) dia

90mm ( Ninety milimetre ) dia

Providing & fixing PVC double equal branch with oval access door insertion rubber washers 3mm ( three milimeter ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

150mm (One hundred fifty milimetre ) dia

110mm (One hundred ten milimetre ) dia as

90mm ( Ninety milimetre ) dia

Providing & fixing PVC clamps ISI marked including fixing with approved adhesive etc. complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

150mm (One hundred fifty milimetre ) dia

110mm (One hundred ten milimetre ) dia as

90mm ( Ninety milimetre ) dia

Providing & fixing PVC reducer ISI marked including jointing with approved ahesive etc. complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

150mm x 110mm (One hundred fifty milimetre into one hundred ten milimeter ) dia

110mm x 90mm (One hundred ten milimetre into ninety milimeter ) dia

Providing & fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etc. complete as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

110mm x 90 mm dia ( One hundred ten milimeter into seventy five milimeter ) dia

Providing & fixing Vitreous China wash down water closet ( Orrisa pattern ) Orrisa Pan W.C.No. 2071 size 58 x 44cm ( Fifty eight into forty four centimetre ) in white shade of Cera or its equivelent ( Earth work, bed concrete,foot rest & trap to be measured & paid for separtely ) as per HP.PWD., specification Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC " P " or " S " trap for water closet (Squatting pan) ISI marked including jointing the trap with the pan & PVC pipe with approved adhesive etc. complete 110mm ( One hundred ten milimetre ) dia as per HP.PWD.,specification Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing in cement mortar 1 : 3 ( One cement : three sand ), a pair of Vitreous China 250 mm x 130 mm x 30 mm ( Two hundred fifty milimeter into one hundred thirty milimeter into thirty milimeter ) foot rests for long pattern squattingh pan water closet as per HP.PWD.,specification Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing Vitreous China wash down water closet ( European type W.C. pan ) with intergal " P " or " S " trap including jointing the trap with soil pipe in cement mortar 1 : 1 ( One cement : one sand ) ( Seat & cover to be measured & paid for separately ) Angle Indian Universal closet of white shade of Hindware or its equilevent W.C. Pan as per HP.PWD., specification Volume -I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of Engineer-in-Charge.

Providing & fixing PTMT coloured/ white automatic flushing cistern with a pair of PVC/C.I. or M.S. bracket complete with fittings including PVC syphonic apparatus, mosquito proof Lid. PVC union & coupling for connections with inlet, outlet and over flow pipe including cutting holes & making good the same ( Over flow pipe to be measured & paid for separately) 5.00 Litre ( five litre ) net capacity as per HP.PWD., specification Volume -I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of Engineer-in-Charge.

Providing & fixing plastic seat ( solid/Hollow type ) & cover for wash down water closet with C.P. brass hinges & rubber buffers Solid Type white plastic seat & cover as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PTMT Jet spray of approved quality & colour with 1.00 ( One point zero zero ) meter tube as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing vitreous China bowl pattern Urinal including connection the Urinal with waste pipe by means of white lead mixed with chopped hemp ( waste pipe to be measured & paid for separately ) Flat back type size 430mm x 260 mm x 350 mm ( Four hundred thirty milimetre into two hundred sixty milimetre into three hundred fifty milimetre ) size as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixingh Division plate for Uninals 600mm x 300 mm ( Six hundred milimeter into three hundred milimeter ) Vitreous China as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing 5 litre ( Five litre ) capacity first quality Vitreous China auotmatic flushing cistern No. 61002 of white shade of Hindware or its equivelent with a pair of cast iron or mild steel brackets complete with fittingh including cast iron syphonic apparatus, mosquito proof lid, C.P. brass unions & coupling for connection with inlet, outlet & overflow pipes including cutting holes in walls & making good the same & connecting the fulsh bend with cistern & closet ( Over flow pipe to be measured & paid for separately ) as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing Vitreous China wash basin with single hole for pillar tap with C.I. Or M.S. brackets painted white including cutting holes & making good the same but excluding fitting flat back white shade No. 102012 of clear size 580 x 400mm ( five hundred eighty into four hundred milimetre ) with pedestal of Hindware or its equivelent as per HP.PWD.,specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing vitreous China Pedestal for wash basin complete recessed at the back for reception of pipes & fittings as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing stainless steel kitchen sink of approved standard ISI marked No. 1250 D of size 610mm x 460mm x200mm ( Six hundred ten milimeter into four hundred sixty milimeter into two hundred milimeter ) with Double bowl steel Sink ISI Marked 304 grade, of Prayag polymers or its equivelent with cast iron or Mild steel brackets painted white including cutting holes and making good the same but excluding fittings as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing M.I. union for wash basin or sink 32mm ( Thirty two milimetre ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. brass waste for wash basin or sink 32mm ( Thirty two milimeter ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. brass flush pipe/ spreaders for urinal with fitting such as unions, clamps etc. ( all in C.P. brass ) including cutting holes & making good the same 15 mm ( fifteen milimetre )nominal size as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing waste pipe flexible coil type not less than 800mm ( eight hundred milimeter ) in length of 32 mm ( thirty two milimeter ) dia as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing sand C.P. grating for gully, floor or Nahni trap as per HP.PWD., Specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing 600mm x 450mm ( six hundred milimetre into for hundred fifty milimetre ) bevelled edge mirrior of superior glass mounted on 6mm (six milimeter ) thick A.C. sheet or plywood sheet & fixed to wooden plugs with C.P.brass screws & washers as per HP.PWD., specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. brass towel rain complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws 750mmx20mm ( Seven hundred fifty milimetre into twenty milimetre ) as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing 600mm x 120 mm ( Six hundred milimeter into one hundred twenty milimeter ) glass shelf with C.P. brass brackets & Guard rail complete , fixed to wooden plugs with C.P. brass screws as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing Chromium Plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing brass bib tap ( superior or heavy type ) 15mm dia ( fifteen milimetre ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. brass pillar tap with capstan head 15mm dia ( fifteen milimeter ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. stop cock 15mm dia ( fifteen milimetre ) dia as as per HP.PWD., specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. brass angle valve 15mm ( fifteen milimetre ) without nuts & pipe ( fifteen milimetre ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing P.V.C. connection with brass union ( a ) 300 x 450 mm ( Three hundred into four hundred fifty milimeter ) length 15 mm ( fifteen milimeter ) nominal bore as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing G.I. / M.I. Union of following sizes ( Where not included in the items )as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15 mm ( fifteen milimeter ) dia

20 mm ( Twenty milimeter ) dia

Providing & fixing brass full way valve with wheel 15 mm ( fifteen milimeter ) nominal bore as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing brass full way valve with wheel 20 mm ( twenty milimeter ) nominal bore as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Constructing manhole with R.C.C top slab in 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete. Inside size 800mm x 800mm and 500mm deep including precast RCC cover with frame for 455 mmx610mm internal dimensions of man hole complete with 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand) complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & laying brick aggregate ( bats ) ( One size ) 50 mm ( fifty milimeter ) nominal size in soak pit/ as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts

Providing & fixing PVC cowl of 110 mm ( One hundred ten milimeter ) size of ISI marked including fixing with approved adhesive etc. complete as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

LAL SINGH CHAUHAN

H. C. Bansal Engg. & Contt.