Repair to leakage, seepage, joinery, flooring, ceiling, sanitary fittings, plastering, painting, approach path, drain and internal electrification and repair/replacement of sewage line, drain path and other misc works of Offrs and JCO MD accn at Ghun

Amount

M&L brick work with sub class 'B' brick straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6 including demolition of existing old brick work or stone masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

Description same as per Item No. 01 above but except brick complete all as specified and as directed. Note : Old serviceable bricks obtained from demolition shall be reused. The rate quoted against this item is inclusive of necessary cleaning and stacking of bricks before incorporation in the work.

M&L brick work with sub class 'B' brick straight or curved on plan to any radius built in cement mortar 1:4 as in half brick thick wall including demolition of existing brick work or stone masonary built in cement mortar including all quoins, arches, pillars etc. complete all as specified and as directed.

Taking down cement plastering of any description on brick/stone/concrete wall surfaces of any description incl racking out joints hacking for key,scrubbing down with water etc. complete all as specified and as directed.

M & L 15 mm thick rendering on brick work or concrete surface in cement mortar 1:4, using water proofing compound surface finished even and fair complete all as specified and as directed. (Note : Rendering will be done in two layer. 1st layer will be 10-12 mm thick and 2nd layer will be 3-5 mm thick. Water proofing compound will be measured and paid separately)

M & L 15 mm thick rendering in cement mortar 1:6 on brick work or concrete surface, surface finished even and fair complete all as specified and as directed. (Note : Rendering will be done in two layer. 1st layer will be 10-12 mm thick and 2nd layer will be 3-5 mm thick.)

M & L applying 2 to 3 mm thick of JK Wall Putty for preparation of old/new surfaces of wall as per manufacturer’s instruction complete all as specified and as directed. Make : Berger/Asian/JK/Birla

M&L for preparation of wall and applying exterior grade wall care putty 2 to 3mm thick to make the surface smooth as specified and directed by Engr-in-Charge.(Note : The work will be carried out upto tripple storey builing the rate of scafolding is included for this item also) Make : Berger/Asian/JK/Birla

M&L for preparation of old decorated surfaces of walls (plastered) by brooming down with core wire brushing, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and finally clean with sand paper complete all as specified and as directed.

M&L for complete all as specified and as directed removal of existing treatment from wall upto plaster surface by electric sand paper grinder, washing, rubbing down and stopping of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces finally rubbed and smooth with sand paper complete all as specified and as directed.

M&L preparation of old decorated surfaces of ceiling (Plastered) by brooming down or sand paper, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots.complete all as specified and as directed

M&L one coat of oil bound distemper in any tint on already prepared old surfaces of walls complete all as specified and as directed by Engr-in-Charge (Note : OBD shall be applied from approved applicator of manufacturer of paint)

M&L two coat oil bound distemper over a coat of primer any tint on already prepared new surfaces of walls complete all as specified and as directed by Engr-in-Charge. (Note : OBD shall be applied from approved applicator of manufacturer of paint)

M&L two coat of cement base paint on already prepared external wall surfaces new surfaces of walls over a coat of priemer complete all as specified and as directed by Engr-in-Charge.

M&L one coat of cement base paint on external wall surfaces already prepared old wall surfaces complete all as specified and as directed directed by Egnr-in-Charge.

M&L two coats of exterior grade 1st quality weather coat paint over a coat of alkali resistant priming paint on already prepared new surfaces of walls all specified and directed by Engineer-in-Charge. Make : Berger XP advance (long life exterior emulsion paint), Asian Paints (Apex Ultima), Nerolac (Excel total)

M&L one coat of exterior grade 1st quality weather coat paint over a coat of alkali resistant priming paint on already prepared old surfaces of walls all specified and directed by Engineer-in-Charge. Make : Berger XP advance (long life exterior emulsion paint), Asian Paints (Apex Ultima), Nerolac (Excel total)

Preparation of old AC sheets surfaces by brooming down with steel wires brushing and washing with water and applying one coat of Apex paint, complete all as specified and as directed

M & L preparation of old painted STEEL surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Cutting around the pipe 75/100mm bore waste pipe/soil pipe including taking out plant roots up to any depth in brick masonary and rejointing in pipe joint in appoxy mortar (Asian/Berger) and making good to existing surface complete all as specified and as directed. (After the jointing pipe one week to be open for checking of leaking including scaffolding)

Removing of bushes upto root level from the wall upto tripple storey builing and repairing of disturbed surface with appoxy mortar with plaster and making good with existing surface with coloured photograph of before and after complete all as specified and as directed

M & L rendering 15mm thick in patches n exc 3 Sqm in cement mortar 1:4 mixed with water proofing compound of cement finished fair faces of brick/concrete surfaces of wall, even and fair without using extra cement complete all as specified and as directed . (WPC will be measured and paid separately)

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds, chajjas and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc. complete all as specified and as directed

M&L for vitrified ceramic tiles light shade, double charged/ultracharged polished (square/rectangular) of 10 mm thick, area of each tile exceeding 0.36 sqm but noy exc. 0.42 sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of the tile over and including 15mm thick screed bed in cement mortar 1:6 dismantling of existing tiling/ flooring including cement mortar bedding (but not backing) and rubbish off the premisescomplete all as specified and as directed.

M&L non skid / mat finish ceramic colour tiles of size 300 mm x 300 mm and 6- 7 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 and dismantling of existing floor tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed.

M&L non-skid / mat finish designed coloured joint free ceramic tiles of size not less than 400 mm x 400 mm x6- 7 mm thick in floor, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed in cement mortar 1:6 and dismantling of existing tiling including cement mortar bedding (but not backing) and rubbish off the premisescomplete all as specified and as directed.

Description same as per item No 26 above but as in skirting including 10 mm thick rendering in cement mortar 1:4, complete all as specified and as directed.

M&L glazed ceramic colour tiles size 450mm X 350mmX 7mm on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4 and dismantling of existing wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed.

M & L PCC 1:2:4 type B-0 using 12.50 mm graded stone aggregate 25 mm thick as in leveling course to floors complete all as specified and as directed.

M & L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in benching to drain, holdfast, padding to roof/chhajja, coping, bed block etc. and the like edge slightly rounded or chamfered including necessary use and waste of form work and demolition of existing old cement concrete (un-reinforced) complete all as specified and as directed.

M&L 75mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection or similar work/places, laid in alternate bays and filling the joints with & including bitumen and sand 1:3 by weight, surface finished even and fair without using extra cement and demolition of existing old cement concrete of plinth protection in ground floor and paving below or above ground level complete all as specified and as directed.

M & L PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling, mass concrete, sub base or leveling course of floor etc. including demolition of existing old cement concrete (un-reinforced) not exc 15 cm thick in ground floor and paving below or above ground level complete all as specified and as directed.

M&L 18 to 20 mm thick machine cut polished granite 1st quality "black" stone slab over kitchen platform and similar places over and including 15mm thick screed bed in cement mortar 1:4 laid and jointed with grey cement slurry mixed with pigment to match with existing surface including demolition of existing stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar including grinding and moulding of exposed edges of granite complete all as specified and as directed.

Taking down and re-fixing the existing shutter in same opening after & including necessary easing/repair etc. exc. 1 Sqm but n. exc. 2 Sqm each complete all as specified and as directed.

Taking down shutter of any description, n. exc. 1 Sqm each complete all as specified and as directed.

Taking down shutter of any description, exc. 1 Sqm but n. exc. 2 Sqm each complete all as specified and as directed.

Taking down chowkhats or frames n. exc 1.5 sqm each without taking off shutter from the frame complete all as specified and as directed.

Taking down chowkhats or frames exc. 1.5 Sqm but not exceeding 4 Sqm each without taking off shutter from the frame complete all as specified and as directed.

S & F second class hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and as directed.

S & F 35mm thick second class hardwood glazed and Skelton factory made door shutters, open rebated and prepared to receive glass/gauze etc divided into squares with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass/ gauge complete all as specified and as directed and specified in SSR Pt I-2009 section 8 clause 8.24 (a).

S&F 30 mm thick moulded WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side palin with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified and as directed. Make : ECHON/Kumar Tech/Sintex

S&F factory made 100% solid wood plastic composite (WPC) door frame of size 75 mm x 50 mm x 50 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof termite proof fire retardant and having good screw holding capacity all as specification and drawing complete all as specified and as directed by Engr-in-Charge. Make : ECHON/Kumar Tech/Sintex

S&F 24 mm thick moulded WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side palin with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified and as directed. Make : ECHON/Kumar Tech/Sintex

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and as directed.

M&L Rolled sections as in framing or cladding, glazing, door chowkat and the like fixed with angle cleats and connecting plates, etc including dismantling old sectioncomplete all as specified and as directed

S & F factory made steel window with side hung shutters including box hinges with steel handle, steel peg stay,tower bolt etc. complete all as specified and as directed with glazing bars, dovetailed or welded including dismantling old steel window complete all as specified and as directed.

S & F factory made steel window with side hung shutters including box hinges with steel handle, steel peg stay, tower bolt etc.complete all as specified and as directed without glazing bars, dovetailed or welded including dismantling old steel window complete all as specified and as directed .

Taking down existing projected type hings from the steel window carefully with disturbing frame and fix 50 mm long mild steel box type hinge weld to steel frame and shutter with welding and making good including touch with paint and with existing surfaces including scaffolding complete all as specified and as directed.

S&F powder coated aluminium ventilator fixed type half gauzed and half glazed with frame made with aluminium section with and including glass frosted/plain, stanless steel wire mesh and aluminium grill fixed with rubber gasket with aluminium beading as specified below including taking down old window/ventilaor : - Frame: 44.5 x 44.5 mm x 1.80 mm thick Side style/rails of shutter - 44.5 x 44.5 mm x 1.80 mm thick Glazing: 5 mm thick frosted glass fixed with rubber gasket and aluminium beading. Wire gauge : stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with aluminium beading Aluminium grill Rubber gasket with aluminium beading complete all as specified and as directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including wooden beading complete all as specified and as directed.

S&F in repair 4 mm thick sheet glass ordinary quality and glazing with silicon and oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane complete all as specified and as directed.

Taking out old loose sheet glass of any description and refxing in repair with silicon and oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane complete all as specified and as directed.

S&F in repairs 18 mm thick plywood coated with fibre reinforced plastic (FRP) 3mm laminated on both faces (3mm+12mm+3mm) and edges to be sealed with PVC edges binding tape for cubboard shelf and shutter complete as per specifications and as directed by the Engineer - in - charge.Make:-Jayna, Brown crust, PLUSCH

S&F in repairs 12 mm thick plywood coated with fibre reinforced plastic (FRP) 3mm laminated on one face (3mm+9mm) and edges to be sealed with PVC edges binding tape for cubboard shelf and shutter complete as per specifications and as directed by the Engineer - in - charge.Make:-Jayna, Brown crust, PLUSCH

All as per item No 55 above but plain white PVC sheet for cup board self, partition, drawer etc complete all as specified and as directed.

S&F auto closing hinges 35 mm of 0 crank OR 8 crank openable at 110 degree for kitchen cabinet shutters Make :Hexa, Shreeji, Hafele

S&F Ball bearing runners 45 mm, 500 mm long telescopic ball bearing drawer channel full extension load capacity 50 kgs, Make :Hexa, Shreeji, Hafele, Hettich

S&F continious (PIANO) hinges, mild steel, bright finish or electrogalvanised. 30 mm width of flaps (when open) complete all as specified and as directed all as specified as directed.

S&F Hasp and staple 100mm safety type, stainless steel 304 grade with hinge pin including bolt to hinge plate and fixed with screws

S&F 100 mm size stainless steel butt hinges and fixed with stainless steel screws, complete all as specified and as directed by Engr-in-Charge.

S&F 200 mm long, solid in one piece stainless steel barrel tower bolts 10mm dia shoot complete all as specified and as directed by Engr-in-charge.

S&F 150 mm long, solid in one piece stainless steel barrel tower bolts 10mm dia shoot complete all as specified and as directed by Engr-in-charge.

S&F 150mm size solid in one piece stainless steel handles, D type, 304 grade and fixed with stainless steel screws complete all as specified and as directed by Engr-in-Charge.

S&F 125mm size solid in one piece stainless steel handles, D type, 304 grade and fixed with stainless steel screws complete all as specified and as directed by Engr-in-Charge.

S&F magnet catcher for cub board with brass body and striking plate including letting in and fixed complete all as specified and as directed.

S&F stainless steel sliding door bolts 204 grade, hasp and staple type with bright bolt not less than 16mm dia with and incl a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 250mm long complete all as specified and directed.

S&F floor door stopper of stainless steel double legged and tongue, 304 grade anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 15 mm bore GI tubing.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 20 mm bore GI tubing.

S&F 15mm bore pipe medium grade galvanised iron with all fittings fixed to wall and ceiling or laid in floor complete all as specified and directed by Engr-in-Charge.

S&F 20mm bore pipe medium grade galvanised iron with all fittings fixed to wall and ceiling or laid in floor complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC connection 15 mm dia 450 tm long with bras fly nut at both ends complete all as specified and as directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including cantilever brackets of suitable angle iron, stainless steel waste coupling , superior quality PVC waste pipe and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S & F in repair vitreous china squatting pan “ORISSA PATERN” of size 580 mm x 440 mm, white, with integral foot rest (excluding flushing cistern and flush pipe) including single trap spun casted 60 cm long fix in eposy mortar connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and as directed. Make: Hindware/Parryware/Jaquar.

S & F in repair 10 litre capacity PVC low level cistern ‘ white’ with inlet, float valve including bracket with 32 mm dia PVC pipe 600 mm long complete all as specified and as directed. Make: Hindware/Parryware/Jaquar.

S&F in reppairs 550x400mm wash basin, vitreous china (Flat back) including pop up brass waste coupling of requisite size, brass CP bottle trap, fixing and pinning in ends of brackets complete all as specified and as directed. Make: Hindware/Parryware/Jaquar.

S & F in repair 75 mm bore UPVC (SWR) pipe 4 kgf/cm2 single socketed in any length with rubber ring, fixed on wall complete all as specified and as directed. Make : Supreme/Finolex

S & F in repair 110 mm bore UPVC (SWR) pipe 4 kgf/cm2 single socketed in any length with rubber ring, fixed on wall complete all as specified and as directed. Make : Supreme/Finolex

S & F in repair 75 mm bore UPVC (SWR) pipe 4 kgf/cm2 single socketed in any length with rubber ring,joints laid in trenches complete all as specified and as directed. Make : Supreme/Finolex

S & F in repair 110 mm bore UPVC (SWR) pipe 4 kgf/cm2 single socketed in any length with rubber ring,joints laid in trenches complete all as specified and as directed. Make : Supreme/Finolex

S & F in repair 75 mm bore UPVC (SWR) bend,'T'socket reducer etc complete all as specified and as directed. Make : Supreme/Finolex

S & F in repair 110 mm bore UPVC (SWR) bend,'T'socket reducer etc complete all as specified and as directed. Make : Supreme/Finolex

M&L cleaning of water storage tank 500 Ltr capacity mechanically using pressure pump with disinfectant chemical including cleaning & removing all scale & dirt etc from existing tanks, mouths of circulating pipes and outer surface of any description & washing down down including writing CA No. on water tank with date of cleaning with synthetic enamel paint complete all as specified and as directed

S&F in repairs 75mm dia cast iron centrifugally cast (spun) floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

S & F in repairs 20 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S & F in repairs ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (Minimum weight 210 gms) complete all as specified and as directed.

S&F in repair of Aluminium body door cill of length not less than 1 mtr at bottom part of door to stop entry of insect inside the room complete all as specified and as directed.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips (TMT)

M&L for TMT bars 6 to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and as directed.

M&L for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and colums, in floors, roofs, landing balconies, canopies, deck slabs, chajja and in shelves and the like, including demolition of existing RCC complete all as specified and as directed.

M&L for steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete.

M&L for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts and structures etc, complete all as specified and directed.

M & L for steel formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed.

Dismantling fencing wire mesh, any type and removing from site complete all as specified and directed.

Dismantling posts & struts; (wood, steel or R.C.C) any section, embeded in concrete, brick work masonary etc including taking out embedded portion & making good distributed ground complete all as specified and directed.

Supply only Chain link fencing, mesh size 100mmx100mm, 3.15mm dia of wire complete all as specified and as directed by Engineer-in-Charge.

Fixing only Chain link fencing including line wires, any mesh size and type to any type of standards rails straining bolts etc including provision of binding wire any size or type complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) in walls or retaining walls,any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and directed.

S&F mild steel work such as in angle iron, horns for fixing of barbed wire, flat iron and nut bolts etc for securing wire mesh etc.,10mm MS round bars as in tie bars fixed to fencing posts including necessary welding where required, including all necessary cuttings, drilling, bolting or riveting etc and as per site requirement and other similar works complete mild steel, conforming to Fe-290 Gde E-165

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 15cm but not.exc 22.5 cm long,diameter of neck n exc12 mm complete all as specified and as directed.

M&L Mild steel round bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (Annealed) not less than 0.90 mm dia or securing with clips quality conforming to round bar bars. complete all as specified and directed.

Taking down Aluminium window shutter size n.exc 1 Sqm including opening up of the corner junctions and replacement of defective members (matching with existing material) alongwith necessary cleats, butt hinges and refixing in the same opening to make the window functional complete all as specified and as directed all a specified and directed. (Note : - Butt hinges and anodised aluminium section shall be measured and paid seperately)

Taking down Aluminium door shutter size exc 1 Sqm but n.exc 2 Sqm including opening up of the corner junctions and replacement of defective members (matching with existing material) alongwith necessary cleats, pivots, locks and refixing in the same opening to make the door functional complete all as specified and as directed. (Note : - Butt hinge ,Pivot, locks and anodised aluminium section shall be measured and paid seperately)

Taking down Aluminium door shutter size exc 2 Sqm including opening up of the corner junctions and replacement of defective members (matching with existing material) alongwith necessary cleats, pivots and refixing in the same opening to make the door functional complete all as specified and as directed. (Note : - Butt hinge, Pivot, Floor spring and anodised aluminium section shall be measured and paid seperately)

Supply only for repairs aluminium section for doors, windows with one or more rebates including joining cleats for fixing etc, complete all as specified and as directed.

S&F in repair glazing (5.00 mm thick float glass) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket and aluminium snap beading etc. complete all as specified and as directed all as directed by engineer-in-charge . (Note : - Existing serviceable aluminium snap beading and EPDM rubber/ neoprene gasket shall be reused. Extra aluminium snap beading and EPDM rubber/ neoprene gasket if required shall be paid and measured seperately as supply only)

S&F in repairs powder coated aluminium door with frame made and shutter and glazing 5 mm thick tinted glass and 12mm thick prelaminated particle board exterior grade in bottom panel, rubber gasket, aluminium glazing clips, mortice lock, aluminium stopper cleat, iron mongary etc. section of aluminium door shall be of following sizes :- Frame 85x44.5x1.20 mm thick fixed with rawal plugs Top rail :85x44.5x1.20 mm thick Middle rail : 85x44.5x1.20 mm thick Bottom rail: 112x44.5x1.20 mm thick Style : 85x44.5x1.20 mm thick Glazing beading : 0.70 mm thick Aluminium handle 'D' type : 150mm Aluminium tower bolt 9.9 mm dia shoot 200mm long Mortice lock-100 mm 4 lever, Aluminium stopper cleat Note :- (i) Making good of wall surface with matching to existing surface complete all as specified and as directed. (ii) PCC shall be measured and paid seperately.

Dismantling asbestos cement sheet (corrugated, semi corrugated) in roof covering including wooden scantling etc.complete all as specified and as directed.

M&L for 6 mm thick asbestos cement corrugated or semi corrugated sheets in roof fixed with 'L' type or J type or cranked hook bolts of old AC sheet complete all as specified and as directed.

S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified and directe by the Engr-in-Charge.

S&F Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified all directed by the Engr-in-Charge.

S & F of rolled mild steel sections as in roof purlins, cleats, rails fastening (beam TEE, angle or flat sections ) includin distance pieces, cleats etc including cutting welding etc conforming to Fe -410-W (Gde E 250 ) quality B complete all as specified and as directed.

S&F in repairs tiled false ceiling of Designer tile Ivory painted (High PressureSteam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or electra) in true horizental level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and croos 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.

Item No 114.00 Contd/--Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 3mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, all complete all as specified and as directed at all heights as per direction of Engineer-in-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 mm getting out, and removing surfplus soil to a distance n exc 50 m and making good surfaces complete all as specified and as directed by Engr-in-charge.

Cleaning of manholes not exceeding 1.5m depth and removing the sludge and burying the waste material in borrow pits complete all as specified and directed.. Note:-(cost of the borrow pit shall be deemed to be included in the quoted rates of this item).

M&L for cleaning of septic tank by de-sludging, distilling and getting out all silt, sludge, organic and inorganic materials by manually/mechanically (solid contents if not removed by mechanically should be removed by manually) and removing the sludge out side of MOD complete all as specified and as directed all as directed at site. After complete all as specified and as directed cleaning of septic tank the manhole cover shall be re-fixed in same position with CM 1:4 and bleaching powder spread on top surface of septic tank @ 1 Kg per septic tank complete all as specified and as directed at site.

Dewatering of soakwell or sewage pit of any dia and depth manually (solid contents if not removed by mechanically should be removed by manually) or by using pump and removal of sludge out side of MOD land complete all as specified and as directed by Engineer-in-charge.

Excavation in trench in any type of soil not exceeding 1.5M wide and not exceeding 1.5M in depth for sewage line, manhole etc not exceeding 10 sqm on plan and getting out in any type of soil complete all as specified and as directed.

Demolition and breaking drain pipe (salt glazed stoneware) 150 mm Internal dia set in cement mortar complete all as specified and as directed.

Demolition and breaking drain pipe (salt glazed stoneware) 200 mm Internal dia set in cement mortar complete all as specified and as directed.

Supplying, laying, jointing and testing salt glazed stone ware drain pipe 150 mm Internal dia grade ‘A’ confirming to IS–651–1980 laid in trenches and jointed in cement mortar 1:1 including cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate complete all as specified and as directed

Supplying, laying, jointing and testing salt glazed stone ware drain pipe 200 mm Internal dia grade ‘A’ confirming to IS–651–1980 laid in trenches and jointed in cement mortar 1:1 including cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate complete all as specified and as directed

Returning, filling in, including spreading, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified and as directed.

Removing excavated material to a distance n exc 50M and deposited where directed at a level n. exc 1.5M above the starting point complete all as specified and as directed.

M&L for 60 mm thick vibromatic reinforced precast cement concrete 1:1:2 (using 20mm graded stone aggregate) with 1.25mm thick mild steel CR sheet around painted with 2 coats of bituminous paint , as in man hole cover slabs, landings finish fair even and smooth without using extra cement ( Top surface will be chequred finish) including necessary form work, 100 mm long handle of 12mm dia round bar counter sunk by 25mm welded to reinforcement including removing the existing damaged covers complete all as specified and directed by Engr-in-charge (Note : CA No and date will be engraved on covers. Reinforcement shall be measured and paid saperately. Curing will carried out with ponding method)

M & L 15 mm thick rendering on brick work or concrete surface in cement mortar 1:4 surface finished even and smooth complete all as specified and as directed.

M&L Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted built in cement mortar 1:6 including demolition of existing old brick work or stone masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed

Description same as per Item No. 128 above but except stone complete all as specified and as directed. Note : Old serviceable stone obtained from demolition shall be reused. The rate quoted against this item is inclusive of necessary cleaning and stacking of stone before incorporation in the work.

Taking down carefully copper/Aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator etc and removing from site and making good disturbed surfaces of walls/floors etc complete all as specified and directed by Eng-in-charge.

M&L for point wiring with 1.5 Sqmm. (nominal area) FRLS, single core PVC insulated 1100 Volts, grade multistranded copper conductor unsheathed in and including concealed PVC conduit medium duty 20 mm dia or higher and heavy grade conduit fittings and heavy duty accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.6mm thick for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, one green colour FRLS cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of following. Make of PVC Wire: Havells/KEI/Finolex/L&T. Note: The wiring to be done as per IE rule and maintain colour code accordingly.

(a) One light point point /bell buzzer point controlled by one-one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

(e) One light point controlled by two way switch

All as per item No 131 above but one 3 pin socket outlet 15 Amp on independent board with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm.

M&L for point wiring with 1.5 Sqmm. (nominal area) FRLS, single core PVC insulated 1100 Volts, grade multistranded copper conductor unsheathed in existing PVC / Steel, concealed and existing MS boxes, mounting of switches, sockets, fan regulator etc with new 3 mm thick plastic laminated sheet as top cover, one green colour FRLS cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of following Make of PVC Wire: Havells/KEI/Finolex/L&T. Note: The wiring to be done as per IE rule and maintain colour code accordingly

(a) One light point point /bell buzzer point controlled by one-one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

(e) One light point controlled by two way switch

All as per item No 133 above but one 3 pin socket outlet 15 Amp on independent board with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm.

S&F switch piano flush, button type 5 Amp SP 250 V AC complete all as specified & directed.

S&F switch piano flush button type 15 Amps SP 250 V AC complete all as specified & directed.

S&F socket outlet multipurpose 3 Pin 5 Amp and 2 Pin 5 Amps 250 V AC complete all as specified & directed.

S&F socket outlet two in one three pin 5 Amp and 15 Amp 2 module 120 W flush type complete al as specified.

S&F Bell switch paino flush button type 5 Amp complete all as specified.

S&F ding dong bell AC 230 V single pole complete all as specified and directed .

S&F switch paino flush button type 5 Amp SP 2 way complete 250 V AC all as specified and directed.

S&F step type regulator socket type double module 5 step for ceiling fan 1200/1400 mm size 230 volts 6 Ampds 400 watts.

S&F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 250 V AC.

S&F lamp holder,pvc/polycarbonate type with back platesuitable for batten fittings including 9w LED bulb complete all as specified & directed.

M&L sub main wiring with 2 Single core PVC insulated unsheathed FRLS cable 1100 Volts grade heavy duty copper conductor multistranded of size 6 Sq.mm. (nominal area) drawing in and including 20 mm. dia or higher PVC conduit medium duty concealed, conduit heavy duty accessories and fittings. Insulated unsheathed FRLS cable copper conductor multistranded of size 4 Sq. mm. as earth wire upto common earth and connected to earth dolly including taking out existing submain complete all as specified & directed Make of PVC Wire: Havells/KEI/Finolex/L&T.

S&F in repairs sheet metal enclosures 240 volt with 200 Amp rated bus bar for double door 8 way DB,s IP-43 IK 09 metal door suitable for one MCB SPN as incoming and 06 MCB SP as out going complete all as specified and directed Make Legrand/Schneider/ABB..

S&F in repairs sheet metal enclosures Triple pole and neutral double door 415 Volt 4 way DBs IP-43 IK- 09 Vertical type suitable for 200 Ams rated bus bar & one MCCB 100 Amp as incoming and 12 MCB SP as outgoing complete all as specified and directed Make Legrand/Schneider/ABB.

S&F MCB double pole 240 Volt 10 KA 40 Amp 'B' series conforming to ISI marked complete all as specified & directed Make Legrand/Schneider/ABB...

S&F MCB single pole and 240 volt 10 KA 5-32 Amp 'B' series conforming to ISI marked all as specified and directed Make Legrand/Schneider/ABB...

S&F MCCB 415 Volt 16 KA 4 pole 63 Amp magnetic trip release & setting as incoming with fixing arrangement complete all as specified and directed. Make Legrand/Schneider/ABB..

S&F in replacement wall mounted tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make: Philips cat part No TMC 501P1xT LED 22WP-3241(Tube Batten) and MAS LE$D 1200mm 18W-865-T-81 (Tube) / Wipro Cat part No WI0922208 (Tube Batten) LL13-181-65SE (Tube)/ Havells Cat Part No LUMILINEPLUSBS20WLED865SPCSS (Tube Batten)CRYSTAL1213T8DSTL20WLED865SGLASS(TUBE DOUBLE SIDE)

S&F in replacement LED down lighter recessed mounted 2x2 feet36W ultra modern designed LED luminaire which provide soft light and glair free symmetrical illumination suitable for grid ceiling and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on as per Havells Cat Part no: ENDURASLIMPROPLUS2x2PLR28/36WLED 840MOD or equivelent make of PHILIPs/ CROMPTONall as directed by Engineer-in-Charge.

S&F in replacement LED light fitting 1x10 w bulk head fitting complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size Make:WIPRO CAT PART NO-LW07-141-XXX-57XXor equivelent , HAVELLS/CROMPTON

S&F in replacement LED light fitting decorative wall mounting SS brush finish fixture with frosted glass suitable for upto 1x40 watt mini glass lamp with and including one no 12 watt LED lamp. complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable sizeAs per Havells Cat Part NO LHFOAJE1TN1IO60 or equivelent of Bajaj/ Philips.

S&F in replacement mirror light decorative compact luminarious with decorative ends caps 9/10 Watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size . Make Havells Cat No Edgelite or equilent in Philips/Wipro

S & F high efficiency LED bulbs 1 X 12 watt that can be used as a ready replacement for existing GLS ad CFL direct fit in holder complete all as specified and directed.

S&F in replacement Integral LED Street Light Luminaire comprising of pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 40/45 watt with efficiency 100 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours, complete all as specified and directed. Make:- Crompton model No. LSTP-45-CDL/Havells model No. ENDURAPEARLNEOSL 40WLED757PASYTOPC /Philips Cat Part No BRP409LED CW036MRFGIPSUGRand syska SSK-ST-40W including taking out old unserviceable street light.

M&L for service cable 6 sq mm twin core Weather proof aluminium multistranded conductor cable PVC sheathed PVC insulated round suspended with No.8 SWG GI wire and reel insulators at distance of 01 mtr duly connected with earthing and clamp etc from Pole to pole including taking out old unserviceable service cable complete Make of PVC Cable Havells/KEI/Finolex/L&T..

All as per Item No 158 but 10x2 sq mm Make of PVC Cable: Havells/KEI/Finolex/L&T.

S&F in replacement electronic ballast for existing tube light fitting 40/36 Watt complete all as specified and directed. Make: Bajaj/Philips/Havells

S&F in replacement LED tube rod 18/20 Watts single or double sided connections polycarbonate complete incl making connection alteration in existing tube light fitting complete.

Disconnecting electric connection and taking down of ceiling fan / Exhaust fan removing capacitor,split pins of any sweep ceiling fan / Exhaust fans complete carefully for overhauling checking of bearings/bush, cleaning the fan blades with cleaning solution, replacing the unserviceable bearing, bush, capacitor , safety split pin and nuts, bolts, washer etc duly threaded of down rods (bush, bearing, capacitor, down rod, hanging clamps, will be paid under relevant item of the Sch 'A') reassembling the ceiling fan complete after greasing/servicing, oiling testing the same making the fan in serviceable condition ana refixing/ hanging the same complete all as specified and directed by Engineer-in-Charge . Note 1: Cost of Split pins, nut bolts and threading of down rod pipe rates are included in quoted rate

Supply only fan capacitor 2.5 mfd make universal / Asian/Epcos .complete all as specified and directed

Supply only fan capacitor 4 mfd complete all as specified and directed make universal / Asian/Epcos

Dismantling electric and water connection of the 25/50 ltr's geyser, taking down from its original position on ground, opening up and removing apparatus plate from the tank, descaling the geyser inner tank and apparatus plate complete, checking for defects, replacement of unserviceable parts such as heating element, syphon assembly, thermostat, rubber gasket etc., reassembling and installation of the geyser into its original position and connecting all electric and water supply connection and testing on completion all as directed by Engineer-in-Charge.(Notes: (i) Heating element, syphon assembly, thermostat, rubber gasket etc if required to be replaced shall be measured and paid separately. (ii) Nut, bolts and hold fastners if required to be replaced shall be deemed to be included in the quoted rates of this item. (iii) All repairs shall be carried out on complaint basis. (iv) The contractor shall collect the complaint slip from JE E/M by 1100 hrs daily. (v) Payment for a geyser will be made only once through out the contract period irrespective number of repair carried out in same Geyser.

Supply only heating element any type/size as per site requirement of capacity 2 KW ISI Marked. Make:-Theta/Newton/Dasmesh/Bajaj

Supply only thermostat for geyser long type 11" in length as per site requirement temp setting on 60 degree centigrade ISI Marked, long type complete all as specified and directed. Make: Dashmesh/Indofors/Donfoss/Bajaj

S&F in replacement of water supply PVC flexible connection Nylon braided with suitable threaded check nut with washer complete suitable for hot/ cold water 15mm dia alongwith threaded Brass nuts and washers 45 cm long complete all as specified and directed. Make:- POLO/Havells/Prayag

Supply only pressure release valve as per existing make and size geyser spring loaded 15 mm dia complete all as specified and directed.

Supply only rubber Gasket as per existing make/size site requirement suitable for 25/50 Ltr capacity geyser complete all as specified and directed.

S&F in replacement Sheet metal enclosure SPN with a two pin and earth plug and socket complete with one 20 amp single pole MCB complete all as specrified & directed

M/S C S AITHANI