MOE5/Ksmart/2859388/2025 Interior work council hall ,Mayor room,front lobby and allied works at main office building at Marine drive

Amount

INTERIOR WORK

OD71589/2025-2026:Preparation and fixing of custom designed wall panels to be installed over the WPC frame in side walls and WPC board of thickness 12mm, including projected decorative beedings / designs with seasoned hardwood reapers and additional covering with 17mm thick WPC board & router mouldings according to design prescribed by the engineer in charge. the rates for the above work are to be inclusive of all cost material, fabrication, transportation and installation. If the paneling width is less than 1 foot, it will be measured in running feet. (Mayor Room - Inside area)

OD73213/2025-2026:Preparation and fixing of custom designed wall panels to be installed over the WPC frame in side walls and WPC board of thickness 12mm, including projected decorative beedings with seasoned hardwood reapers as per router mouldings according to design prescribed by the engineer in charge. the rates for the above work are to be inclusive of all cost material, fabrication, transportation and installation. If the paneling width is less than 1 foot, it will be measured in running feet.

OD74387/2025-2026:Preparation and fixing of custom designed ceilling to be installed over the steel frame in ceilling with base of WPC board thickness 12mm, including projected decorative designs with seasoned hardwood reapers and additional covering with 32mm thick WPC board or above & router mouldings or CNC works according to design prescribed by the engineer in charge. the rates for the above work are to be inclusive of all cost material, fabrication, transportation and installation. If the paneling width is less than 1 foot, it will be measured in running feet

OD116136/2025-2026::Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: (1) The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. (2) Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. (3) On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. (4) On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer- in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.) Up to 3m height

OD119631/2025-2026::Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: (1) The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. (2) Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. (3) On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. (4) On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer- in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.) Above 3meter

OD74501/2025-2026:Providing and fixing of lettering by using SS material with PVD coating finish using 1mm thick sheet and letters having 2 cm projection and back light including all necessary primers done with the help of screws, anchor fastners, installation charges etc. "LOGO"

OD74576/2025-2026:Providing and fixing of lettering by using SS material with PVD coating finish using 1mm thick sheet and letters having 2 cm projection and back light including all necessary primers done with the help of screws, anchor fastners, installation charges etc. "COCHIN CORPORATION"

OD74631/2025-2026:Supply and installation of WPC / sythetic wood fininsh skirting panels / Beedings of various thickness with matching colour scheme all along the curved falls wall along the bottom touching the carpeted council hall flooring and making grid design in the ceilling area. Fixing has to be done with steel screws of sufficient length.

OD74796/2025-2026:Preparation and fixing of custom designed vertical section, WPC panels of 12mm thick covered the steel vertical strcuture of steel square holow pipe, including painting and polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture according to design prescribed by the engineer in charge. the rates for the above work are to be inclusive of all cost material, fabrication, transportation and installation. Vertical section length : 4.5 to 4.80meter

OD74865/2025-2026:Preparation and fixing of custom designed vertical section, WPC panels of 12mm thick covered the steel vertical strcuture of steel square holow pipe, including painting and polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture according to design prescribed by the engineer in charge. the rates for the above work are to be inclusive of all cost material, fabrication, transportation and installation. Vertical section length : 2.1 to 2.6 Mtr

OD75614/2025-2026:Providing and fixing of lettering by using SS material with Golden coating finish using 1mm thick sheet and letters having 2 cm projection including all necessary primers done with the help of screws, anchor fastners, installation charges etc. "COCHIN CORPORATION"

OD75274/2025-2026:Preparation and fixing of custom designed handrail of height 120cm as per the architectural design by using 30mm x 30mm square steel pipe on top and bottom line covered with WPC board, including designed plates, projected decorative beedings with seasoned hardwood reapers as per router mouldings according to design prescribed by the engineer in charge. the rates for the above work are to be inclusive of all cost material, fabrication, transportation and installation.

OD109363/2025-2026:Providing and fixing of lettering with SS material using 1mm thick sheet and letters having 3cm projection and back light including all necessary primers done with the help of screws, anchor fastners, installation charges etc. "COCHI MUNCIPAL CORPORATION"

OD109384/2025-2026:Providing and fixing of design / Photo with SS material using 1mm thick sheet and letters having pasted on acrylic sheet of 12mm thickness suitable to fix on behind mayors desk and back light including all necessary primers done with the help of screws, anchor fastners, installation charges etc. Photo of Gandhiji.

OD109392/2025-2026:Providing and fixing of design / Photo with SS material using 1mm thick sheet and letters having pasted on acrylic sheet of 12mm thickness suitable to fix on behind mayors desk and back light including all necessary primers done with the help of screws, anchor fastners, installation charges etc. Corporation logo.

OD75390/2025-2026:Providing and applying wall paper on finished walls as per the instruction againist engineer in charge

13.45.1:Finishing walls with textured exterior pint of required shade:New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

P.P.JOB (BID ID -2241363)

Bidder Name

P.P.JOB

Paulson K T