SPL REPAIR OF ESH/ MAG 03 NOS (03,06,17) AT AMN POINT OF CERTAIN MIL UNIT AND SPL REPAIR TO MD ACCN NO 4/N/1 25 AT SUJIT VIAHR OF CERTAIN MIL UNIT UNDER GE (S) BINNAGURI

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified

Demolition of cement concrete (Unreinforced) Concrete of any description and in any position not otherwise specifically provided complete all as specified

Demolition of Reinforced cement concrete of roofs,floors(other than ground floors), beams, staircase, landings, chajjas and similar suspended work complete all as specified

M&L for non skid coloured joint free ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but n. exc. 0.18 Sqm, in floors etc. set and jointed in neat cement slurry over 15mm thick screed bed or bedding layer in CM (1:6) as in floor and pointed in whiter or coloured cement to match as in floor complete all as specified

M&L of coloured Non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floor etc set and jointed in neat cement slurry over 15mm thick screed bed or bedding layer in CM (1:6) as in floor and pointed in whiter or coloured cement to match as in floor complete all as specified

M&L for non skid coloured joint free ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18Sqm but n. exc. 0.38 Sqm, vertical surfaces, in skirting etc. set and jointed in neat cement slurry and pointed in whiter or coloured cement to match as in floor complete all as specified

M&L 15mm thick rendering in cement mortar 1:6 on other than fair face of brick work or concrete surface finished fair and even (without using extra cement) complete all as specified

M & L for glazed ceramic colour tiles 300X 450 X 7 mm thick as on cup board vertical surface of wall such as skirting, dado, riser etc. in Bath, WC and Kitchen set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified

Providing holes to cooking platform of size 25 mm dia for inserting cooking gas pipe in suitable place complete all as specified

Taking down cement plaster on wall & ceiling of any description including racking out joints, hacking for key and scrubbing down with water etc complete all as specified

M&L for 20 mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers (10mm & 10mm) mixed with water proofing compound in top layer 200 ml per beg of cement or as per manufacturer's instructions finishing the surface fair and even without using extra cement complete all as specified . (Note: Water proofing compound shall be measured and paid seperately under relevant item of schedule 'A').

M&L for rendering 5mm thick plastering in CM (1:3) on ceiling, soffits of slabs, chajjas, columns and beams etc and finished the plastered surface even and smooth without using extra cement complete all as specified

M&L for prepartion of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer after applying 2 coats of cement based wall putty 1 mm (average thickness)each to wall surface complete all as specified

M&L preparing newly plastered or unplastered surface of ceiling and applying three coats of white washing complete all as specified

M&L applying two coats of weather proof exterior emulsion paint of standard quality and make ,over a coat of white primer including preparation of new /old wall surfaces complete all as specified

Supply only liquid water proofing compound complete all as specified

Dismantling water tanks and removing from site of capacity exc 250 & n.exc 500 ltrs complete all as specified

Taking up or down GI 15mm bore pipe and connection including cleaning for refixing or removal from site complete all as specified

Taking up or down GI 20mm steel tubing and connections incl cleaning for refixing or removal to store complete all as specified

Material and labour for hoisting and fixing rotational moulded polyethylene(double layer) water storage tanks 500 lit capacity (Cylinderical vertical), ISI marked(IS-12701:1996) hoisted and fixed in position including inlet, oulet, over flow connection, ball valves etc complete all as specified.

S&F 20mm bore Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all complete as specified

S&F 15mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall etc complete all as specified

Refixing old 15mm GI tubing and connections on new or old position (walls, ceilling, floor etc) complete all as specified

Supply and fixed in repairs sinks with drainage board made of stainless steel 1mm thick sheet plugs, washers and waste pipe, including bedding in cement mortar to dwarff wall and connecting union to pipe of overall size 915mmx460mm bowl size 410mm x 330mm x 160mm all complete as specified

S&F in repairs vitreous china wash basin, white, flat back, size 550x400m excluding taps, waste , including chain & plug & porcelain stopper ,brackets, cutting for pinning in ends of bracketes or erecting stand and fixing and supply and waste pipe complete all as specified

S&F 15 mm fancy type pillar taps, cast copper alloy with capston heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore complete all as specified

S&F in repair CP toilet paper holder with flat recessed type stainless steel complete all as specified

S&F in repair 10 ltr capacity dual type PVC flushing cistern low level white colour incl PVC connection PVC flush pipe of reqd length complete all as specified

S&F in repairs Bib taps fancy type cast copper alloy, chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule all complete as specified Make: Marc (Cat part No:F101915 or equivalent in Jaguar)

S&F in repair 15 mm bore angle cock CP with flage complete all as specified Make: Marc (Cat part No:MJN-1060)

S&F in repairs stop valves fancy type cast copper alloy, chromium plated with long shank and cup (concealed type) for 15mm bore pipe, screwed both ends including necessary fittings such as sockets for pipe or for union all complete as specified

S & F in repair 15mm bore PVC Connection with PTMT nut of length 600 mm complete all as specified

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white including connection trap and to flushing pipe, anti-syphnoge pipe etc complete including complete all as specified

S&F in repair PVC seat cover for pedestal pan, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminiumised hanging device complete all as specified

S&F in repair CP health faucet (ABS body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 m long flexible tube and ABS wall hook in cluding making connections and fixed in position complete all as specified Make: Marc (Cat part No:MAC-3051)

S&F in repair for brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chomium plated bracket guard and railing 60 cm long complete all as specified

S & F Soap dish, vitreous China white of approximate size 160 x 160 x 90 mm embeded in the wall all as specified

S&F in repair PTMT towel ring complete all as specified

Taking down eaves gutter ,rain water pipes ,CI/PVC/AC soil pipe with fittings from wall, treches of any description including fittings complete all as specified

Supply and fix PVC (SWR) pipes 110mm dia,type 'A' conforming to IS, single socketed, in any length with rubber ring joints laid in trenches or floor complete all as specified.

S&F 110mm dia PVC bends of any radius acess door complete all as specified

S&F 110mm dia PVC (SWR) branch piece single (single 'Y'/T) equal or unequal with acess door complete all as specified

S&F 110mm dia PVC SWR vent cowl complete all as specified

Taking down chowkat with shutter exc 1.5 sqm and n. exc. 4.00sqm each and removing from site complete all as specified

Taking down shutter of any description but exc 1 sqm and n. exc. 2 sqm each complete all as specified

S&F for pressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 125mm x 60 mm x 1.25mm (thick) complete all as specified

S&F for pressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 105mm x60 mm x 1.25mm (thick)complete all as specified

S&F second class hard wood Glazed and skeleton shutters 35 mm thick open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

M & L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified

S&F 30mm flush shutter, solid core construction, with block board core and plywood face panel, commercial type on both side etc complete all as specified

S&F Solid PVC door frame of size 50x47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, supplied and fixed incl fixing of hold fast as per specification and drawing complete all as Specified.

S& F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 4mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification with Wood free EPS complete all as Specified.

S&F 150 mm long Aluminium anodised barrel tower bolts complete all as specified

S&F aluminium handles 125 mm size cast type anodised complete all as Specified.

S& F of 140 mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified

S&F 100 mm butt hinges stainless steel complete all as specified

S&F for Stainless Steel Sliding door bolt of 300mm long , fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as Specified

M & L for 75mm Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified

S&F Powder coated aluminium window sliding type three track (2 glazed & one gauze shutter ) aluminium sections weighing not less than 1.67kg/m for frame and 0.55 kg/m for shutter including necessary jointing cleats, glazing cleats, rubber packing , screws, handle, locking arrangement and 4 mm thick plain/tinted glass and aluminium mosquito proof gauge including taking down of old existing steel window and making good disturbed surface of wall complete all as specified

S&F Powder coated aluminium louvered ventilators of size n exc 0.50 Sqm area with glass louvers, without sash bars of aluminium sections weighing not less than 0.605kg/m for frame of size 40x20x2mm including necessary jointing cleats, glazing cleats, rubber packing , anodised aluminium snap beading,screws, anodised aluminium fittings and 5.5mm thick tinted glass fixed in panels with suitable locking arrangements including taking down of old existing steel ventilator and making good disturbed surface of wall complete all as specified

S&F Framed work such as grills,gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framedguard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F in repair swivel shower of CP with shower arm 150 mm size for fixing with 15 mm bore GI pipe complete all as specified

S&F in repair 1.00 mm thick stainless steel plate rack of size 31"x30"x10" complete all as specified (Make - Model No BSKPR-314 of Blue Star/Nirali or its equivalent make)

S&F Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed in 15 mm dia GI pipe complete all as specified

M&L for TMT bar 10mm dia and over cut to length,bent to shape required, and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified

M&L for TMT bar 8 mm dia and over, cut to length, bent to shape required, including cranking, and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified

Use and waste of formwork to sides and soffits of, shelves, platform etc rough finished surfeces of concret flat etc complete all as specified

Use and waste of formwork edge of concrte flats,treads breaks in floors,window cill,concrete railing openings in concrete walls floor and roofs n exc 20 cm wide and sids of Rcc/Pcc bands in walls horizontal or sloping and similar work exc10cm but n exc 20cm wide complete all as specified

M&L for 25 mm thick PCC (1:2:4) type B0 ( 12.50 mm graded stone aggregate) , as in under layer levelling course for Bath,WC floor below tiles finished even and rough complete all as specified

S&F in repair MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for grils, rails etc complete all as specified

M&L for salt-glazed stoneware gully traps, square or round mouthed, type `P' 150x100mm complete all as specified

M&L for preparation of new of previously untreated steel and Iron surface of any description, not otherwise described over 10 cm width or girth and applying two coats of Synthetic enamel paint over one coat of red oxide primer complete all as specified

Demolition of brick work built in cement mortar of any description complete all as specified

M&L for brick work with burnt fly ash old size bricks, straight or curved on plan to any radius, built in CM 1:4 as in half brick thick wall complete all as specified

M&L for brickwork with burnt fly ash old size bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete.

Removing building materials and debris (other than excavated earth) to a distance of 5 KM inside MD Land at locations specified including loading and dumping/ leveling at the destination complete all as specified

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified.

M&L for 75mm thick PCC (1:3:6) type C-2 with using 40mm graded stone aggregates as in plinth protection laid in panels and finished even and fair including necessary form work complete all as specified Note: Joints 12mm wide joints to full depth of PCC shall be provided at every 3 meters interval and at every change of direction and shall be filled with mixture of bitumen and sand in 1:3 by weight . Cost of provision shall be deemed to be included in quoted rate of this item.

S&F in repair 0.56 mm thick plain aluminium sheeting bend to shape fixed with pins to door shutter to prevent water splashing,ridges, hips,valley gutters, drip and straight flashings over crumple joints complete all as specified

M&L for RCC nominal mix 1:1.5:3 type A1 using 20mm graged stone agreegate as in chajjas and like complete all as specified

Use and waste of form work to chajjas and like finished rough complete all as specified

Do as above but as in soffits of suspended slabs such as roof slab, floor slab landings and similar work n.exc 200 mm thick complete all as specified

M&L for RCC nominal mix type A1,1:1.5:3 using 20mm gradded aggregate Slabs supported on walls, beams and columns in floors, shelves, platform, lintel, deck slabs and the like complete all as specified

M&L for 10mm thick rendering in CM (1:4) as backing layer in vertical surfaces of skirting dados repairs to steps complete all as specified

M&L for preparation of new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as Specified.

S&F in repair stainless steel curtain rods 20-25 mm dia, anodised aluminium alloy with fixing brackets, stops, and complete fitments all as specified

M&L for complete removal of existing treatment of old plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer after applying 2 coat of cement based wall care putty 1 mm each including complete removal of existing treatment all as specified

Taking down tarfelt with cement plaster from roof surfaces and lowering and removing the same to a distance exc. 500m and n. exc. 900m incl roughening of old concrete suirface of roof by wire brushing and cleaning the surface to remove all loose dust etc complete all as specified

M&L for mild steel rolled sections conforming to Fe - 410 (Gde E-250) as in main and cross beams, hip and jack rafters; verticals , purlins where connected to common rafter and running rails and guides for sliding doors and steel doors any type; fixed with angle cleats or other connecting plates complete all as specified

M&L for MS flat iron bent to shape, holes drilled etc complete as in wind ties etc including one coat of red oxide paint complete all as specified

M&L for MS plate of any size & thickness, holes drilled or without drilled etcc including one coat of red oxide paint complete all as specified

M&L for 75 mm thick cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in path /steps laid/ Hardstanding with and incl use and waste of form work and finishing the surface even and rough to receive the topping layer or tiling complete.

M & L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate as in surface channels/drain including forming fair finished to drain channel.

M&L for preparartion of old surfaces applying two coat of white washing on ceiling surfacecomplete all as specified

Material and labour for applying one coat of synthetic enamel paint on old painted steel and iron surfaces of any description over 10 cm in width or girth including necessary preparation of surfaces.

M& L for two coat of Oil bound distember on new wall surface including preperation of the surface complete all as specified

M & L for preparing new Plastered surfaces of walls and finishing the walls with Acrylic smooth exterior paint of required shade for New work Two or more coats applied over and including priming one coat of exterior primer applied complete all as specified .

Use and waste of formwork to sides of pillars, posts, struts, piers,columns, and stanchions for rough finished surfaces of concrete complete all as specified

Providing and applying Fosroc Brushbond Roof Guard, a single component High build fibre Reinforced Acrylic Waterproofing render for roofing system to be applied by brush, at three coats at a minimum dry film thickness of 1mm, which should cure by reaction with atmospheric moisture to give a tough elastomeric waterproof membrane. Solid Content : 70 % Tensile strength ASTM D 412 : 1.10 Mpa Elongation ASTM D12 : 100% Resistance to ageing due to : 1000 hours UV radiation ASTM D4587 E : No Change Rapid Chloride Penetration ASTM C 1202-03 : Very low Pull off adhesion ASTM D4541 : 0.92 Mpa Resistance to Algae growth ASTM D 5589-97 : Passes, Zero rating Permeability (mm) (BSEN 12390 part 8) : 5.0 Water vapour transmission (ASTM E96) : 6.0g/m² h

M&L for 10mm thick screed bed or bedding layers in cement mortar (1:4) in order to maintain proper slope over existing roof surfaces for applying single component acrylic polymer modified, finished even and smooth without using extra cement mixed with water prrofing compound complete all as specified . (NOTE : Polymeric membrane and WPC shall be measured and paid separately under relevant item of this Schedule 'A').

M&L 25 mm thick PCC 1:2:4 type B0 (Using 12.5 mm graded stone aggregate) mixed with water proofing compound and laid on RCC slab as base layer for roof treatment roughening the top surface of concrete by using broom sticks while the concrete is green complete all as specified .(NOTE : water proofing compound paid separately under relevant item of this Schedule 'A').

M&L for 40mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone agg as in floor finhished surface even and smooth w/o using extra cement complete all as specified

Supply only glass dividing strip 38mm wide and 3mm thick in flooring complete all as specified

Removing & Hacking of existing concrete Carefully by low impact high frequency hammer OR by manual chipping without damaging the existing concrete or control sand blasting including cleaning the surfaces by air jet etc. complete.(Mode of measurement- per sqmt of breaking area of concrete)

For rusted metal (iron base) apply Reebaklens RR or Equivalent with brush for complete wetting of rusted metal surface and allowed to react it for 16-24 hours. After 24 hours, a white layer will appear which will protect further corrosion of metal / steel for about 5-7 days. Before applying protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth complete all as specified

Providing and applying two coats of Nitozinc Primer or Equivalent a two component epoxy zinc rich Primer or equivalent product on the properly cleaned and prepared steel bars after the required chipping and cleaning of the concrete surface as per the manufactures’ specification complete all as specified

Supply and applying a bond of Fosroc Nitobond SBR Latex, or Equivalent SBR Latex based bonding agent admix with cement as per manufacturer recommended ratio complete all as specified

Guniting concrete surface with single component, fibre reinforced shrinkage compensated, polymer modified structural grade repair mortar like Fosroc Renderoc SP 40 or equivalent at a thickness of 25 mm. The repair mortar should have a compressive strength 45 N/mm²,flexture strength 7 N/mm² and tensile strength 2.5 N/mm² at 28 dayscomplete all as specified

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified

M&L for point wiring with 1.5 sqmm single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with multistranded copper conductor with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI Marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI Marked) with proper colour coding as earth continuity conductor connected to common earth dolly, modular sheet steel sunken terminal box of appropriate size suitable for modular switch/ fittings concealed in walls, with modular back plate, top cover fixed flush to wall for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles all as specified for the following :-

One light point controlled by one way switch 5/6 amps.

One ceiling fan/Exhaust fan point controlled by one way switch 5/6 amps.

One socket out let 5/6 amps point on the independent board

One socket out let 5/6 amps point on the same board

One bell point controlled by one way switch 5/6 amps.

All as per item No 114 above but wiring with 2.5 sq mm single core multistranded copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified

S&F switch piano flush type 5/6 amps single pole one way complete all as specified

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified

S&F of socket outlet 2 in 1, 5 Pin, 5/15 amp, multipurpose 230 volt flash type complete all as specified

S&F switch piano flush type 15/16 amps single pole one way complete all as specified

S&F bell push 5 amps single pole one way complete all as specified

S&F call bell pding dong complete all as specified

S&F ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified

S & F lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified

S & F deluxe fan electronic regulator not less than not less than 80 watt, 230 volts, AC, rotary step white/ivory finish complete all as specified

S&F, IP 20, class I, LED tube light fittings 20 W (or nearest next higher wattage) (4feet), wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 5KV or more, luminaire efficacy > 120 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with three core PVC cable of copper conductor of size 23/.0076 and making connection complete all as specified.

Taking down carefully Ceiling fan from its original position and refixing / hanging after B/R plaster work complete all as specified

M&L painting of ceiling fan complete, in situ with synthetic enamel paint by spraying including filling cavities with filler one coat after cleaning all dust etc, all as specified

S&F MCB distribution boards (DBs) with sheet metal enclosure, double door, IP protection 43 amp rating 100 Amp , 240 Volts, 8 way, single pole and neutral, with din rail (as per OEM), neutral link, earth link earthing studs, suitable for fixing MCBs, without MCBs fixed flush to wall/other surface complete including taking down old unsv one all as specified

S&F MCB, Single pole & neutral 32/40 amps, 240 volts, ‘C’ curve, 10KA complete including taking down old unsv one all as specified

S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete with and including taking down old unsv one as specified

Taking out old unserviceable GI Pipe of any size from site complete all as specified . Note : The Excavation and earth work shall be mesured and paid separately under relevant item of Schedule.

Supply and lay pipe galvanized, “Medium class”, including fittings 20 mm fixed complete to walls and ceiling or laid in floor complete all as specified

Supply and lay pipe galvanized, “Medium class”, including fittings 25 mm complete all as specified

Supply and lay pipe galvanized, “Medium class”, including fittings 40 mm complete all as specified

Supply and fix Gun metal ,globe Gate Valves with iron wheel head of 20 mm dia bore complete with all accessories all as specified

Supply and fix Gun metal ,globe Gate Valves with iron wheel head of 25 mm dia bore complete with all accessories all as specified

Supply and fix Gun metal ,globe Gate Valves with iron wheel head of 40 mm dia bore complete with all accessories all as specified

M& L for cutting existing GI pipe alteration or addition of 40/50 mm dia bore for inerstion of reducer Tee complete with all accessories all as specified

Excavation in trenches in soft/loose soil not exc. 1.5 metre wide and not exc. 1.5 metre in depth and getting out for taking up / laying under ground electric cable complete with all accessories all as specified

Returning, filling in, including spreading levelling watering and well rammming in layers not exceeding 25 cms in depth complete with all accessories all as specified .

Removing excavated materials n.exc 50m and depositing were directed at a level n.exc. 1.5m abive the starting level complete all as specified

Taking out old unserviceable cable of any size carefully from trenches ofter disconnecting electric connection, GI pipe protection, with and including separating serviceable bricks & set aside and removing un-serviceable bricks from site complete all as specified Note : The Excavation and earth work shall be mesured and paid separately under relevant item of Schedule.

Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated PVC bedded, galvanized steel strip or wire armoured LT electric power UG cables, heavy duty with stranded aluminium conductor of cross sectional area 25 sqmm 3.5 core with and including all fixing & connecting accessories such as Aluminium cable lugs, cable gland, nut, bolts, washer etc complete as specified (NOTE: Earthwork & Excavation, GI pipe, bricks for protection etc shall be measured and paid separately under relevant items of this schedule 'A').

Supply and lay dry river sand filling for under ground cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified

Supply and laying sub class B bricks of size 25cmx12.5cmx7.5cm (+/-10% tolerance) for protection of UG cable with width equal to length of bricks as mechanical protection laid dry and flat complete all as specified

M & L for horizontal boring across the existing road without disturbing the road surface for inserting GI pipe complete all as specified. Note :- (i) Removal of surplus soil shall be deemed to be include in the unit Rate. (ii) GI pipe will be measured and paid separately under relevant item of Sch 'A'.

M&L for 40 mm bore steel tubing light grade ISI marked for protection of cable including necessary joints complete all as specified

Supply and fix switch flame proof rotary type with termination box in LM6, 16A, single pole 250V all as specified

Supply and fixing LED light fitting 1x16 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size all as specified

Refing Flamproof Tubelight of any wattage under ceiling complete including connecting up with three core flexible copper conductor cable with suitable size all as specified

Fixing only Flamproof light of any wattage under ceiling complete including connecting up with three core flexible copper conductor cable with suitable size all as specified

S & F LED flameproof light fittings 30 Watt ,230 VAC outdoor type, CIMFR-BIS-PESO certified, recommended for gas group IIC, Zone I & II, temperature class T6 toughned glass cover with IP66 protection complete all as spedified . Make-Crompton Cat part No-FWL1318-30-CDL-M, Sudhir or equivalent

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete including taking out the old one complete all as specified

S & F Flameproof weatherproof 8 Way control panel in cast alumiunm alloy LM6 construction for group IIA/IIB considering Incoming -01 Nos of 40A MCB SPN, Outgoing- 06 Nos MCB SP 6 A, concealed in wall complete all as specified

M&L for air termination, single pointed aluminium rod 12 mm dia and 300 mm long with necessary fixing arrangement on roof including taking down old one complete all as specified

M&L for test point terminal block made of gun metal or phosphorus bronze size 75x75x25 mm, drilled and screwed copper/aluminium bi-metal strip including 3 Nos 8 mm dia 25 mm long hex head screw including taking down old one complete all as specified .

M&L Aluminium stip 25 x 3.15 mm fixed on and including saddles, pcc, pvc insulators and fixing screws etc. for roof conductors and down conductors including taking down old unsv strip.

S&F galvanised iron strip of size 32 x 6 mm buried in ground or fixed on wall mounted on suitable sized porcelain insulators ( on floor and wall only) including cutting cavities for fixing of porcelain insulators and finishing with cement plaster on wall /floors and connected to test point including bending, jointing at test points with GI nuts, bolts, with lead washers, jointing strips at all joints incl. making good the disturbed surfaces including taking down old one complete

Refixing Aluminium Strip 25 x 3 mm with saddles & fixing screws etc,for earth continuity conductor main earthing lead , roof conductor & down conductors above ground suitably fixed to wall or concealed in wall , or passing through pipes incl. all necessary fixing arrangement for lightning protection and taking down old unsv strrip complete all as specified

Fixing in repair the existing dislocated/fallen air termination rods 300mm long,12 mm dia fixed on PCC blocks/on GI pipe/ directly on roof including GI pipe etc, complete all as specified

Fabrication and instalation of cubical shape enclosure made of MS/CRCA sheet 2.00mm thick with front detachable cover, anodixed fiexing screw cap, washers 4 Nos to be mounted on wall with wooden plugs & screws 4 Nos duly painted inside and outside by two coats of aluminium paints over a coat of redoxide primer overall dimension of enclosure 150mm x 150 mm x 100 mm (depth) for fixing inside test point terminal block including taking down the old one complete all as specified

M&L for point wiring complet with 1.5 sqmm multistranded copper conductor single core PVC insulated, IS 694 unsheathed FR-ls cabe 1100 volts grade (ISI marked) with proper colour coding drawn through and including steel coduit not less than 20mm dia and conduit accessories (ISI marked) concealed in wall/ fixed to roof, ceiling etc including provision of 1.5Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sunken terminal box made out of GI sheet no less than 1.22 mm thick for boxes duly painted with anticorrosive paint, concealed in walls with bakelite/ plastic laminated sheet top cover fixed with cadmium plated iron screws for housing, switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sunken for boxes and making good to the distrubed surface of wall /floor and matching with existing specification all as specified for the following:- (a) For flame proof point wiring

Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground )earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connected to galvanized earth strip 32x6 mm dia by means of bolts, nuts check nuts and washers of galvanized iron or steel all as shown in electrical plate No 3 connected to earthing test point all as specified or indicated including testing on completion and including taking down the old one complete all as specified

M/S MOHAN KUMAR BANSAL (BID ID -3367587)

M/S SHYAM ENTERPRISE (BID ID -3367600)

ROZI KHAN (BID ID -3367258)

M/S SINHA ENTERPRISE (BID ID -3367363)

SINGH & CO (BID ID -3367294)

ANIL KUMAR SAH (BID ID -3367670)

N K Construction (BID ID -3367711)