68/EDCB/2023-24

Amount

The work of safe carriage of the following material from CB Ganj store center to work site under the jurisdiction of EDD-II Bareilly Approx. distance upto 60 Km. Including safe loading and unloading.

ST Pole 11 Mtr

PCC Pole 8.5 Mtr

ACSR Weasal Conductor

AB Cable 3x120 sqmm

AB Cable 3x95 sqmm

AB Cable 3x50 sqmm

11/0.4 KV 3 Phase 400 KVA T/F

11/0.4 KV 3 Phase 250 KVA T/F

11/0.4 KV 3 Phase 100 KVA T/F

11/0.4 KV 3 Phase 63 KVA T/F

11/0.4 KV 3 Phase 25 KVA T/F

LT Cable 1x120 sqmm

LT Cable 1x240 sqmm

LT Cable 1x400 sqmm

LT Cable 3.5x150 sqmm

LT Cable 3.5x70 sqmm

11 KV Incoming Panel (VCB)

11 KV Outgoing Panel (VCB)

Other Line material

Construction of T/F plinth 1.5x1.5x2 m3 for mounting 250 KVA T/F including foundation work (below ground 0.5 M), Brick work, RCC slab of 4” thickness and plastering in 1:6 ratio with 02 Nos channel pieces of 1.5 mtr long of size 100x50x6 mm compete in all respect

Cage fencing of 250 KVA Plinth mounted transformer in Town areas to avoid electrical human/cattle accidents by fabrication of cage (1 Inch Sq wiremesh) made of 10 No gauge in suitable size angle iron frame of size 7.5'(L)x5'(W)x8’(H) by strenghtening of wire mesh 20x3 mm M.S. flat haorizentally as well as vertically, Grouting the panel with 1:2:4 cement/coorse send/brick ballast. The Frame should be bolted on angles at the four corners so that frame may be un-bolted/bolted at the time of replacement of the transformer. Provision of 1 gate should be there for maintenance of the transformer. Painting (1 coat of red oxide + 2 coat of Bus green enamel paint). The wire mesh should be earthed with 50x6 mm MS earthing strip with existing earthing of Transformer Body. All men, material and T&P provided by the contractor to complete the fabrication, transportation and installation.

Pipe Earthing of Transformer (By boring of 4 inch diameter 20 m deep, 40 mm diameter A class GI pipe is inserted to a depth of 20 m and a holed pipe of 1.5 m length is inserted at the bottom. Tighten one end of the MS strip of size 50x6mm with the nut bolt with the neutral of the converter and weld the other end with the GI pipe inserted in the boring for earthing. Putting a socket on the upper part of the pipe (mouth) so that water can be poured into it to retain moisture. To complete the work Contractor will provide all material, Manpower, T&P, safe carriage of material to worksite. Above work will be carried out under supervision of concerned JE/SDO/EE)

Dismantling and removing of old and used/damaged 11 KV VCB (1 Incoming & Outgoing) in Control room including opening/cutting of power cable connection and earthing strip with dragging/cartage from control room to J.E. Store.

Erection/Installation of following new panel (VCB) in control room including grouting of Anchor bolt of Panel and making/repairing of pocket for cable to insert in panel from trench and fixing, taping of bus bar with wiring for PT. AC, DC connection including providing of AC & DC Supply.

11 KV Incoming Panel (VCB)

11 KV Outgoing Panel (VCB)

Providing cutting, fixing and welding of MS Strip from existing, earthing to new 11 KV VCB Complete in all respect, all material shall be arranged by the Contractor.

Dismentaling of 250 KVA Transformer as per norms complete in all respect

Dismentaling of 100 KVA Transformer as per norms complete in all respect

Dismentaling of 16 KVA Transformer as per norms complete in all respect

Dismentaling of 10 KVA Transformer as per norms complete in all respect

Mounting of 250 KVA T/F Transformers as per norms complete in all respect -

Mounting of 400 KVA T/F Transformers as per norms complete in all respect -

Mounting of 100 KVA T/F Transformers as per norms complete in all respect -

Mounting of 63 KVA T/F Transformers as per norms complete in all respect -

Mounting of 25 KVA T/F Transformers as per norms complete in all respect -

Fabrication & Installation of 11 KV Fuse set unit to be installed on midway of 11 KV Double Pole Structure. Material Detail for complete the work given below :- 1. MS Channel 100x50x2028mm) - 1 Nos (Provided by Contractor) 2. Iron Strip (50x5x305mm) - 3 Nos (Provided by Contractor) 3. 200 mm Fuse wire of required capacity - 3 lenght (Provided by Contractor) 4. Holding Clamps - 2 Nos (Provided by Contractor) 5. Aluminium Lug 70 sqmm - 4 Nos (Provided by Contractor) 6. Off Size Nut & Bolt - As Required (Provided by Contractor) 7- 11 KV Composite Pin Insulator - 6 Nos (Provided by Department) (Manpower & T &P would be provided by the contrator at his own cost)

Erection of Single/Double pole in H.T/L.T lines including fitting of all accessories as per RESSPO Norms

PCC Pole 8.5 Mtr (Single)

ST Pole 11 Mtr long (Double)

PCC Pole 8.5 Mtr (Double)

Grouting of following Pole with 1:4:8 mixture in size(450x450x1500mm.) including cost of cement/BB & sand Required as per RESSPO Norms

PCC Pole 8.5 Mtr (Single)

ST Pole 11 Mtr long (Double)

PCC Pole 8.5 Mtr (Double)

Laying of LT Cable 1x120 sq mm complete in all respect

Laying of LT Cable 1x240 sq mm complete in all respect

Laying of LT Cable 1x400 sq mm complete in all respect

Laying of LT Cable 3.5x150 sq mm complete in all respect

Laying of LT Cable 3.5x70 sq mm complete in all respect

The work of Driving the earthing electrode and making connections with 6 S.W.G. GI wire as per RESSPO Norms

Laying, Stringing & Sagging of Following Conductor complete in all respect

ACSR Weasal Conductor

AB Cable 3x120 sqmm

AB Cable 3x95 sqmm

AB Cable 3x50 sqmm

The work of digging of pits, erection of Stay Clamp, Insulator etc.

Grouting of stays, 1:4:8 cc ratio (600x600x300mm.) as per RESPO norms.

Fixing of 3 Pahse Distribution Box complete in all respect

Fixing of 1 Pahse Distribution Box complete in all respect

Supply and Fixing of Following Material as per RESPO norms complete in all respect (would be Provided by contractor through approved vendors of Discom at his own cost)

Stone Pad 300x300x75 mm

Distribution Box Clamp

Cross Arm Holding Clamp

F Clamp with Nut & Bolt

Danger Board With Clamp

Barbed Wire

Aluminium Lug 120 sqmm with Nut&Bolt

Aluminium Lug 240 sqmm with Nut&Bolt

Aluminium Lug 400 sqmm with Nut&Bolt

Tailless Unit 400 Amp

Tailless Unit 600 Amp

Stay Clamp

Earth wire Clamp

P G Clamp

Holding Clamp for S/s

Holding Clamp for LT T-Off

Holding Clamp for M S Channel

LT Clamp With Nut & Bolt

Stay Insulator

LT Shackle Insulator

Nut & Bolt for Shackle Insulator

Piercing Connector

Safe back carriage of Following item (if any) from work site to C.B. Ganj store Bareilly approx distance upto 60 Km including loading & unloading.

11 KV VCB (Damaged)

11/0.4 KV 3 Phase 250 KVA T/F

11/0.4 KV 3 Phase 100 KVA T/F

11/0.4 KV 3 Phase 16 KVA T/F

11/0.4 KV 3 Phase 10 KVA T/F

M/S SAMAR ELECTRICALS