Providing WSS to SC abadi in village Rajiana under Constituency Kangra

Amount

Excavation in foundation trenches etc. in (pipes and pits ) in all kinds of soil such as pick work, Blasting work,soft/hard rock, blasting by chiesling soft / hard rock where blastng is prohibited in all lifts Stacking the excavated soil not more than 3 metres away from the edge of excavation and then returning the stacked soil in 15 cm layers when required in to plinth and sides of foundations, consolidating each deposited layer by ramming , watering and then disposing of all surplus excavated earth, unusable materials as directed with in all leads/lifts and to the entire satisfaction of Engineer-in-charge

Laying jointing and testing of bevelled ended G.I. pipe (medium class )with circumfernital butt welded joints (94%) by electric arc welding thickness shall be equal to pipe wall thickness )and testing of G.I. pipe of following dia confirming to ISI 1239-1990 (part-III) having wall thickness as specfied below capable of with standing required test pressure including manufacturing and fabrication of reducers/ tapers all short pices required degree of bends etc . as per site requirement made from parent tubes and the laying of pipe with MS flanged of required table including welding of flanges joints of pipe (6%) duly welded including nuts. The welding electrodes shall be as per IS: 814 of Advani oerlikon/L&T of ISI marked make the damaged portion of pipes (if damages during laying and joints operation of pipe). The rates also including entire carriage of material flushing cleaning and hydraulic testing of pipes D.P. test of butt welded joints complete in all respect and to the best satisfaction and direction of Engineer-in-Charge complete within all leads and lifts.

From RD 0.00 to 750Rmt. 100 mm dia of pipe (midium class) flange table -5

From RD 0.00 to 10.50 Rmt. 100 mm dia (midium class) flange table -17

Providing, fixing, MS flanges confirming to IS-6392-1971 (Latest with upto date ammendments) of class /Table -5 specified welding both sides of flanges according to relevant standereds i/c nuts bolts and rubbur sheet washer confirming to IS 1367-1981 and carriage of material with in all leads and lifts.

MS flange 100 mm dia table -5

Providing & supplying of clear water Submersible pump set capable of handling high thread turbidity of KSB/ Kalama/SU/Johnson/Crompto/ make single and open impeller clear water handling pump confirming to latest BIS code.The pump shall be fitted with single vane impeller of suitable alloy for handling clear water as per IS 9283-1979 having oil/ grease packed bearings and stainless steel shaft, wound stator on motor side with shaft protection sleeves on pump side ensuring better life for shaft .The impeller of pump shall be directly mounted on extended submersible square cage motor shaft conforming to BIS-8034-1976 with upto date ammendments of 2900 RPM, totally dust & weather proof with detach able pump casing for easy inspection with double mechanical seal grease/ oil lubricated and provided with stainless steel thrustbearing plate to withstand vertical load with minimum wear & tear .It should be fitted with device to take up expension of water on heating of motor & suitable for operation on 415 +/-10% volts 3 phase 50 C/S AC supply.The power of motor should be at least 10% in excess of maximum power required by the pump in complete operating range with mounting stand/duck foot bend ,steel guide wire with mounting hook lowering chain and standard accessories as supplied by the manufacturers complete and suitable for fulfilling the the following requirements:-

(Discharge=6.64 LPS each set & Total Head= 42.75 mtrs). 100mm Dia of Rising main = 750 mtrs Length. For Stage- I

Supply , Installation, Testing and Commissioning of Fully Automatic LT Panel for Submersible pump made out of 16 Gauge sheet powder coated dust and veremin proof wall mounted and front opering door type switch board with copper insulated wiring suitable to operate 2 nos. pump of required capacities as per data given in 4.1 automatically through Variable Frequency Drive Starter. Starter should be capable to handle all the faults like short circuit, over current, under current, over voltage, under voltage, dry pump protection. It should get on and off command automatically from PLC and HMI. Monitoring and controlling of Pump running and tripping status should be monitored and controlled remotely through IOT enabled device. Access should be given to 3 users. Make: Aarmation Electric Private Limited/MAS/ELLES/Adlec

Variable frequency drive starter of required capacities as per data given in 9.1 of Heavy Duty for smooth start and smooth stop of pumps and for the energy conservation in the system. It Should be capable to control the frequecy of pumps through out the operation and also should be capable to maintain the power factor of the system within acceptable limits. It should have ambient temperature 50 Degree without derating and have conformal coating class 3C2, so that it can work in any harsh environment like moisture etc. Make: Aarmation Electric Private Limited/MAS/ELLES

Multi function meter indicating different parameters like Current, Voltage, KWH, PF, THD etc with RS 485 communication Make L&T/Conserve/Siemens

Main incomer MCB /MCCB suitable capacity of L&T / Standard make on the coming feeder for pumping set confirming to BIS 2516-1985 ( Latest edition) with neutral linked under voltage release.

LED Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 ( Part I & II ) latest with upto date ammendments.

LED On/Off indicator and push button, Control and power wiring,Power capacitor,Cooling fan 230 VAC, Contorl terminal, Buss Bar, i.e.Bolt, insulator, etc.

Slector Switch for Auto and manul Operation

Input Choke of required HP for Energy saving variable frequency Starter which should be installed at the input of Energy saving variable frequency starter, so that there should bo proper protection in case of any voltage surge and distortions.

Control Transformer to safegaurd the control circuit of all the components from the voltage surges and spikes. Make: Aarmation Electric Private Limited/MAS/ELLES

Power and Control wiring and Busbar

Surge suppressor device with isolating MCCB to eliminate the power surges due to lightening and system surges.

Power quality monitoring & controling realy with Control Contactor to safeguard the Electronic & Electric elements

Independent Control panel with swithch fuse unit and fuses of Suitabvle Amperage to eliminate the kitkat fuses of HPSEB Make: Aarmation Siemens/Schneider/L&T

Providing and installation of horizontal spindle casing/end suction(back pull out arrangement) single/double/ multistages Centrifugal pump or combination of pumps in series, parellel of recommended make such as Mather and Platt/KSB/Kirloskar /Crompton/Becon weir/BE/Jyoti as per BIS 1520-1980 with upto date ammendments read with 9542-1980 or latest addition suitable to lift clear water under mentioned characteristics with bronze impellers/priming funnels casing rings and shaft sleeves of bronze, shaft of steel grade EN-8 with cast iron casing coupled directly through a flexible coupling on a common mild steel base plate (base plate to be from the manufacturer of the pumping unit only) to squirrel cage/slipering screen protected drip proof induction motor of standard make such as Kirloskar / Crompton / BHEL/ NGEF / GEC / Siemens / Jyoti / ABB / Lubi suitable for operation on 400(+/-) 10% volts, 50 cycles/second, 3 phase AC electric supply. The power of electric motor should be at least 10% in excess of the maximum power required by the pump in the operation range of (+)10% and (-) 25% of the duty point head. The motor should be as per IS; 325-1978 with upto date ammendments. it should include cost of bearing nuts bolts and pointing etc.and should meet the following requirements:- The pumping machinery shall be installed on a proper designed base plate. The foundation of the machinery should be proper designed and anchored properly.The rate of each set shall be inclusive of all required accessaries of complete automation.

(Discharge=15.18 LPS each set & Total Head= 239.92 mtrs). 150mm Dia For Stage- I centrifugal pump

Supply , Installation, Testing and Commissioning of Fully Automatic LT Panel for Submersible pump made out of 16 Gauge sheet powder coated dust and veremin proof wall mounted and front opering door type switch board with copper insulated wiring suitable to operate 2 nos. pump of required capacities as per data given in 5.1 automatically through Variable Frequency Drive Starter. Starter should be capable to handle all the faults like short circuit, over current, under current, over voltage, under voltage, dry pump protection. It should get on and off command automatically from PLC and HMI. Monitoring and controlling of Pump running and tripping status should be monitored and controlled remotely through IOT enabled device. Access should be given to 3 users. Make: Aarmation Electric Private Limited/MAS/ELLES/Adlec

Variable frequency drive starter of required capacities as per data given in 10.1 of Heavy Duty for smooth start and smooth stop of pumps and for the energy conservation in the system. It Should be capable to control the frequecy of pumps through out the operation and also should be capable to maintain the power factor of the system within acceptable limits. It should have ambient temperature 50 Degree without derating and have conformal coating class 3C2, so that it can work in any harsh environment like moisture etc. Make: Aarmation Electric Private Limited/MAS/ELLES

Multi function meter indicating different parameters like Current, Voltage, KWH, PF, THD etc with RS 485 communication Make L&T/Conserve/Siemens

Main incomer MCB /MCCB suitable capacity of L&T / Standard make on the coming feeder for pumping set confirming to BIS 2516-1985 ( Latest edition) with neutral linked under voltage release.

LED Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 ( Part I & II ) latest with upto date ammendments.

LED On/Off indicator and push button, Control and power wiring,Power capacitor,Cooling fan 230 VAC, Contorl terminal, Buss Bar, i.e.Bolt, insulator, etc.

Slector Switch for Auto and manul Operation

Input Choke of required HP for Energy saving variable frequency Starter which should be installed at the input of Energy saving variable frequency starter, so that there should bo proper protection in case of any voltage surge and distortions.

Control Transformer to safegaurd the control circuit of all the components from the voltage surges and spikes. Make: Aarmation Electric Private Limited/MAS/ELLES

Power and Control wiring and Busbar

Surge suppressor device with isolating MCCB to eliminate the power surges due to lightening and system surges.

Power quality monitoring & controling realy with Control Contactor to safeguard the Electronic & Electric elements

Independent Control panel with swithch fuse unit and fuses of Suitabvle Amperage to eliminate the kitkat fuses of HPSEB Make: Aarmation Siemens/Schneider/L&T

Automation Submrisible and Centrifugal Pumping Machinery)

PLC (Programmable logic controller ) with appropriate digital and anlog inputs and output to give automatic command to Star Delta Starter panel/ Energy saving variable frequency starter Make: Aarmation Bechoff Automation/Rockwell Automation

Electronic realy card 8 channel

SMPS 4.5 Amps to energise PLC system

HMI (Humen Machine Interface) 7" display for Monitoring and Contriling of Submersible pumps Make: Aarmation Bechoff Automation/Rockwell Automation

Control MCB for Automation System

Level Sensor to indicate the water level of tank remotely

Shieldede data Cable for Communication of level Sensor with PLC

Installation and Commissioning and software Development for all above item complete all respect Engineer-in-charge

Supply, Installation Testing & comissioning of str delta starter pannel for centrifugal pump made out of 16 guage sheet, powder coated dust & vermin proof wall/ base mounted and front opening door type with copper insulated wiring suitble to operate 1 no pump of rating required HP through star delta starter mechanism. Starter should be capable enough to handle the following fault like short circuit over current , under current over voltage dry run protection and phase loss with LED ON/OFF & Trip indicator Make Armation Electric/ L & T/ Schinieder.

Star, Delta and Mains Power Contacters of required ratings as per type-2 co-ordination for required HP

Voltage Protection device to protect panel from over voltage and under voltage.

Single phasing and phase reversal protection device to safeguard system from single phasing and phase reversal of the supply voltage.

Muti-function meter indicating different parameters like Current, Voltage, KWH, PF< THD etc with RS 485 communication Make Aarmation/ L&T/ Schneider/ Seimens

Main incomer MCB/MCCB suitable capacity of L&T/ Schneider/ ABB make on the feeder for pumping set confirming to BIS 2516-1985 (Latest edition)

Individual Starter incomer MCCB/MCB of suitable capacity of L&T /Schneider/ABB/make on the feeder for pumping set confirming to BIS 2516-1985(Latest edition)

Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 (Part-I & II) latest with upto date ammendments.

LED On/Off & Trip indicator and push buttons, Control and power wiring, Power capacitor, Cooling fan 230 VAC, Control terminal, Bus bar, i.e. Bolt, insulator, etc.

Surge suppressor device with Isolating MCCB to eliminate the power surges due to lightening and system surges.

Control Transformer to provide a stable control voltage to safeguard the control circuit of all the components from the voltage surges and spikes.

SS ENGINEERING WORKS

dinesh kumar lath

sadeep kumar

MANAHOR LAL SURINDER KUMAR

SG Engineers and Consultants

SANJAY SAINI