SPECIAL REPAIR TO COMMUNITY CENTRE AND BADMINTON COURT AT TBRL RANGE RAMGARH

Amount

Taking down chowkat with shutter n. exc. 1.5sqm each (without taking off shutter from the Frame) etc complete all as specified and directed.

All as per serial item No 1.00 above but exc 1.5 sqm but n exc 4 sqmm each.

Taking down shutter of any description but exc 1 sqm and n. exc. 2 sqm each and refixing in same opening complete all specified and directed.

All as per serial item No 3.00 above but exc 2.0 sqm each.

Supply and fixing for solid PVC door frame of size 50x47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, as per specification complete as directed.

Supply and fixing for factory made solid pannel PVC door shutters 30mm thick (style) consisting of frame made out of MS tube for top and bottom rail, MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside the solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the ms frame welded/sealed to the stiles and rail with suitable pvc sheet beading, and jointed together with solvent cement, at site on per specification complete all as specified and directed.

Supply and fixing for 75mm butt hinges medium weight cold rolled stainless steel.

Supply and fixing for 150 mm long Aluminium anodised barrel tower bolts.

Supply and fixing for 125mm size aluminium anodised door handles.

Supply and fixing for 35mm flush shutter, solid coare construction, with block board core and plywood face panel, commercial type on both side etc complete all as specified and directed.

Supply and fixing for 200mm long Aluminium anodised barrel tower bolts.

Supply and fixing for 150mm size aluminium anodised door handles.

Supply and fixing for sliding door bolt of 300mm long plate Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy all as specified and directed.

Material and labour for preparation of new wooden surface of any description n. exc. 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer all as specified and directed.

Material and labour for pressed steel frames of size 105x60 mm for door with one or more rebates incl necessary fittings, lugs, hinges, lock strike plate, flat iron hold fast etc complete as specified and directed.

All as per serial item No 15.00 above but size 125 x 60mm

Material and labour for 2nd class soft wood plain fillets square, rectangular or triangular in section, clean sawn, exc 13 and n exc 25 sq cm , se-cured with nails, complete all as specified.

Material and labour for cement concrete (1:2:4), type B-1, using 20mm graded mechanically crushed stone aggregate as in coping, bed block benching, kerbs stone, mud stop, rounded or chamferred on edges including necessary form work/moulds complete all as specified and directed.

Taking down cement plaster of any description racking out joints hacking for key scrubbing down with water etc to receive plaster complete all as specified.

Material and labour for 15mm thick rendering on fair faces of brick wall or concrete surface in CM 1:4, surfaces finished even and fair with out using extra cement all as specified.

Material and labour for 15mm thick rendering on fair faces of brick wall or concrete surface in CM 1:6, surfaces finished even and fair with out using extra cement on walls, all as specified.

Material and labour for 5mm thick rendering on fair faces of brick wall or concrete surface in CM 1:3, surfaces finished even and fair with out using extra cement on ceiling, chajjas, fasicas, soffits etc , all as specified.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of smooth interior plastic acrylic emulsion paint over one coat of primer Including one coat wall putty to smoothen the surface to obtain smooth regular/even finish using sand paper etc. complete all as specified and complete all as specified and directed by Engr-in -Charge. (Tint and shade as approved by the GE)

Material and labour for preparation of new plastered surfaces of walls applying one coat of primer using necessary filling compound of white cement wall putty to obtain smooth regular/even finish using sand paper etc. complete all as specefied and applying two coats of smooth exterior acrylic emulsion paint on new surface complete all as specefied and directed by Engr-in -Charge.

Material and labour for preparation of new plastered surfaces of ceiling and applying two coats of oil emulsion distemper over a coat of primer including putty to celing surface etc complete all as specified and directed by Engr-in-Charge.

Material and labour for for preparation of old surfaces of wall including complete removal of existing treatment of plaster or unplastered surfaces washing, rubbing down by wire brushes, stopping of surfaces and levelling/ edging the disturbed places/edges using necessary filling compound of white cement wall putty to obtain smooth regular/even finish, using sand paper and applying two coats of interior plastic acrylic emulsion paint over a priming paint plaster coat complete all as specified and directed by Engr-in-Charge (Tint and shade as approved by the GE)

Material and labour for preparation of plastered or unplastered old distempered surfaces of ceiling including pilasters and cornices and applying one coat of oil emulsion distemper (any tint) on ceiling complete all as specified and directed by Engr-in-charge. (Including of one coat wall putty wherever necessary to smoothen the surface

Material and labour for complete removal of existing treatment from external surfaces of walls by wire brushes&stopping of surfaces & levelling/edging the disturbed places /edges using necessary filling compound of altek putty to obtain smooth regular/even finish using sand paper and applying two coats of exterior acrylic emulsion(Apex Ultima) over one coat of primer complete all as specefied and directed. Note: The tint and shade shall be as approved by the GE. the treatment shall be carried out by the authorised applicator of the firm complete all as specefied and directed by Engr-in-Charge.

Material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width and applying one coat of synthetic enamel paint (1st quality) complete all as specified.

Material and labour for preparation of old painted wood/wood base surfaces of any description not otherwise described over 10cm width and applying one coat of synthetic enamel paint (1st quality) complete all as specified.

Material and labour for two coat of synethic enamal painting to steel surfaces any descrtiption over 10 cm in width or girth not otherwise described incl preparation of surfaces.

Demolition of brick work built in cement mortar of any specification and in any position complete all as specified and directed.

Material and labour for brick work with sub class 'B' old size bricks built in CM (1:6) all as specified.

Dismantling floor/hearth or wall tiles including cement mortar bedding (but not backing) and removing the rubbish off the premises complete all as specified and directed.

Material and labour for 40mm thick cement concrete type B-0 1:2:4 (using 12.5mm graded aggregate) as in floor complete all as specefied and directed.

Material and labour for 9-10mm thick vitrified ceramic coloured tiles, light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match shade of tiles, over and including screed bed 15mm thick in cement motar 1:6 complete all as specified and directed.

Material and labour for glazed ceramic tiles in vertical surface 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in colour cement to match over 15mm thick rendering cm (1:6) complete all as specified

Material and labour for non - skid ceramic coloured tiles 7 to 8 mm thick, (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles, over and including screed bed 15mm thick in cement motar 1:6 complete all as specified and directed.

Material and labour for glazed ceramic tiles (coloured) 300X 200 X 6-7mm thick on vertical surfaces set, jointed in neat cement slurry and pointed with white cement mixed with pigment to match over 15mm thick rendering cement motar 1:4 all as specified and directed.

Material and labour for machine cut Granite stone slab 20mm thick laid over 20mm thick screed bed in CM(1:6) as in counter platform set complete and jointed with grey cement slurry mixed with pigment to match the shade of slab including grinding and polishing complete all as specified and directed.

Material and labour for machine cut granite stone slab 20mm thick, in skirting/dado laid over 15mm thick rendering and jointed with grey cement slurry and pointed with white cemetn with admixture of pigment to match the shade of granite stone including grinding and polishing etc complete

Material and labour for, Marble tiles 30cmx20cmx20mm thick machine cut, bedded jointed and pointed/joints with wihite cement slurry including cutting and polishing types etc complete all as specified. (Make : Black Zebra Bhainsalana)

Material and labour for 20mm thick marble tiles machine cut in skirting/dado laid over cement screed and jointed with grey cement slurry including cutting and polishing to type, etc complete. Make : Black Zebra Bhainsalana

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified.

Material and labour for 75mm thick CC type D-2 1:4:8 (40mm Agg) as in subbase.

Supply only sand for screed bed min 25mm thick for paving flooring

Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade over watering and consolidating complete . Note: sand will be measured separately.

Material and labour for 75mm thick PCC 1:3:6 type C2 (using 40mm graded aggregate) as in hardstanding and plinth protection etc complete all as specified.

Material and labour for grinding and bee-wax polish to kota stone as in floor, steps etc complete

Supply and fixing for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 etc complerte all as specified.

Demolition of RCC of any description and in any postion not otherwise specifically provided for etc complete.

Material and labour for formwork to chullah hoods, chajjas troughs and similar items including edges etc complete

Material and labour for RCC 1:2:4 type B0 (using 12.5mm graded aggregate ) as in chajjas etc complete

Material and labour for mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips .Fe-410-W (Gde.E-250) Part- I quality-A or Fe 290 (Gde -E-165) etc complete

Supply and fixing in repairs rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) capacity 500 litres, hoisted and fixed in position complete all as specified.

Supply and fixing for ball valve brass 20mm bore, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

Taking up or down steel tubing 15mm bore and connections, including cleaning for refixing or removal to store complete all as specified.

Taking up or down steel tubing 20mm bore and connections, including cleaning for refixing or removal to store complete all as specified.

Supply and fixing for 15mm bore tubes, medium grade, galvanised, with all fittings & fixed complete to walls & ceilings or laid in floors complete all as specified.

Supply and fixing for 20mm bore tubes, medium grade, galvanised, with all fittings & fixed complete to walls & ceilings or laid in floors complete all as specified.

Refixing 15mm dia old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified.

Refixing 20mm dia old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified.

Supply and fixing in repair 10 ltr capacity PVC flushing cistern low level white colour incl PVC connection PVC flush pipe of reqd length CI brackets in lieu of old unservisable push button flushing system

Supply and fixing for vitreous china wash basin, white, counter top, size 550x400m excluding taps, waste , chain & plug & porcelain stopper but exclusive of fixing of supply and waste pipe incl dismantling old wash basin any description.

Supply and fixing in repair vitreous china squating pane orissa pattern size 580x440mm white with internal footrest (excluding fixing bolts flushing cistern and flush pipe

Supply and fixing in repair PVC seat cover for pedestal pan, black closed pattern with flat bottom and cover and mild steel chromium plated or aluminiumised hanging device complete all as directed.

Supply and fixing in repair vitreous china wash down water closet pan (Pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe, complete all as specified and directed.

Supply and fixing in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

Supply and fixing for sink with drainage board made out of stainless steel sheet 1.0mm thick with plug, washers and wastes, overall size 915 x 460mm, bowl size 410x330x160mm etc incl taking down old sink complete all as specified and directed.

Supply and fixing in repair cast copper alloy chromium plated Bib taps long body fancy type 15mm bore, with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed.

Supply and fixing in repair 15mm bore long body fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply and fixing in repair 15mm cast copper alloy chromium plated angle cock etc complete all as specified and directed.

Supply and fixing for shelf of PTMT fixed with and including CP brass screws and wooden plastic cleats (min wt 300 gms) etc complete

Supply and fixing for high density polyethylene (HDPE) 32mm pipe pressure seating 6 kgf/sq cm. etc complete

Supply and fixing in repair vitreous china urinal, full stall type, bowl type or half stall pattern, basin only including connections to flushing pipe and out going pipes etc (ex

Supply and fixing for Vitreous china urinal partition white of size 310x700 mm, terminating about 40 cm above floor line, fixed in repairs etc complete

Supply and fixing for urinal spreader of PTMT white for fixing with 15mm dia pupe (minium weight 60 gms) etc complete

Supply and fixing in repair stop valve, cast copper alloy, 15mm bore, screwed done, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed etc complete.

Supply and fixing in repair stop valve, cast copper alloy, 20mm bore, screwed done, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed etc complete.

Supply and fixing in repairs stop valves fancy type cast copper alloy, chromium plated with long shank and cup (concealed type) for 15mm bore pipe, screwed both ends including necessary fittings such as sockets for pipe or for union all complete as specified and directed.

Supply and fixing in repairs PVC connection 15 mm bore with PTMT nuts of length 450 mm long.

Supply and fixing for 25mm dia mild steel MS power coating fancy type curtain rods with fixing brackets, knobs etc complete

Supply and fixing in repair 32mm brass CP bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing,union and cap and fixed.

Supply and fixing for 150mm length floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor etc

Dismantling of 100mm dia cast iron or reinforced concrete drain pipes, jointed inn cement mortar and taking out of trenches, if required etc complete

Supply and fixing for 100mm dia cast iron floor trap with grating including jointing to water pipe fixed in cement concrete type B1 (1:2:4) etc complete

Supply and fixing for 100mm dia cast iron soil, waste and vent pipes in any length with or without ears, with cement joints laid in trenches or in floors

Material and labour for french polishing on surface of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on old works with two or more coat

Supply and fixing for 110mm PVC(SWR) pipes single socketed, in any length with rubber joints, laid in trenches or in floors etc complete

Supply and fixing for 110mm PVC(SWR) single, (single T) equal or unequal etc complete

Hackingout old borken glass (any thickness size, quality or description) from wooden frme or stone concrete or brick surrounds, glaze with putty or fixed with beads complete all as specified.

Supply and fixing for 3 mm thick frosted glass and glazing with oil putty/beads in square n,exc. 0.50sqm in each pane complete all as specified and directed.

Supply and fixing for 5.5mm thick sheet glass ordinary quality and glazing with oil putty/beads in square exc 0.5 sqm.

Supply and fixing in repair aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aparture 1.40mm and fixed with aluminium wire staples; etc complete

Material and labour for anodised aluminium standard section of size 101.60x44.45x2mm thick for door/window frame including joiniting aluminium cleats of suitable size and lugs etc complete all as specified.

Material and labour for anodised aluminium door shutters single/double leaf, side hung type, with top and lock rail of size 83x44.45x2mm thick bottom rail 150x44.45x2mm thick, styles/meeting styles shall be of size 83x44.45x2mm thick including jointing cleats, rubber beading snap fit clips, alumnium screws etc, panels fitted with prelaminated particle board/glass including builders hardware ie aluminium tower bolt 150mm long 2 nos to each shutter, aluminium door handle 200mm long 2 nos to each shutter complete all as specified. (glass to be measured and paid separately).

Supply and fixing for aluminium anodised window shutters, powder coated, side hung type without sash bars, aluminium section 83x44.45x2mm thick including necessary jointing cleasts, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium builders hardware such as peg stage 150mm long 01 no, aluminium handle of size 100mm-01 no as in each shutter, window shutter to be fitted with glass panes etc complete (Glass panes to be measured and paid separately)

Supply and fixing for double action floor spring hydraulically regulated made up of miniumum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed.

Supply and fixing for aluminium(extruded section) door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed etc complete

Supply and fixing for 100mm size mortice locks of brass body, 4 levers suitable to aluminium door shutters etc complete all as specified.

Material and labour for aluminium anodised section of 101.60x44.45x2mm for aluminium partitions, powder coated fixed in postion etc complete all as specified.

Supply and fixing for powder coating anodised aluminium grills, 7.5mm wide, 6mm thick fixed to aluminium windows/partitions/door frames including all fixing arrangements like aluminium channels, screws etc complete all as specified & directed by Engr-in-charge.

Material and labour for 21mm thick wood Imported Maple flooring as in floor, 50 to 85mm width, ramdom length in tongue and groove shape. The edges of the boards will have a finger lock grove and the bottom side with air pass groove; above pine wood runners of size 70mm x 45mm treated with anti-termite solution and fixed on the bottom side with 10mm thick EPDM air cushioning pads by nails through the two wings at 350mm c/c etc including Game line marking of suitable colour as approved by GE and 02 Nos movable Net poles as recommended by BWF etc complete all as specified and directed.

Material and labour for 75mm thick cement concrete type B-2 1:2:4 (using 40mm graded aggregate) as in floor complete all as specefied and directed.

Supply and fixing for suspended false ceiling includes GI angle of size 0.5mm thick having two equal flanges of 25mm along perimeter of ceiling, screws fixed to brick wall with the help of nylon sleeves and screws at 610mm centre to centre. Suspended HD tube section of size 18mm x 40mm x 0.8mm thick with the help of level adjuster made of zinc alloy 50mm x 25mm from soffit at 1220mm centre to centre with ms flat 25mmx3mm thick fixed to offit with GI cleat and metal expansion fastner. HDU section of 0.56mm thickness having knurled web of 40mm and two equal flanges of 35mm with lips of 8.5mm fixed to the HD tube section with help of connecting clips and in direction prepenciular to the main section at 610mm centre to centre 12.5mm thick tapered edge Gyp board shall be fixed to HDU section with 25mm drywall screws at 230mm centre to centre (Gyp Board shall be measured & paid for separately).

Supply and fixing for 12.5mm Gypsum board to frame work including jointing taping complete all as specified and directed.

Taking down carefully copper /aluminium surface/conceled point wiring (Light, fan, socket, or power) complete including fittings and fixture such as switches, ceiling roses pendents, regulators sockets / DBs / main switches include boards etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately), removing material, from site and making good the disturbed surfaces of walls, floor complete all as specifed and directed.

Taking down the existing unserviceable main switches/DB's any type including boards from its position and making the good of disturbed surface complete all as directed.

Taking down carefully by sub main wiring/service connection of any type complete all as specifed and directed.

Point wiring with 2 single core 1.5 Sqmm (nominal area) PVC (FRLS) insulated sheathed copper stranded conductor cable run in and including concealed in wall/floor PVC conduit not less than 20 mm as per IS with all fittings such as bends, tee, junction boxes of suitable size including 1.5 Sqmm PVC(FRLS) insulated copper earth continuity conductor connected to common earth dolly and including MS/GI sunken boxes with modular inner & surface plate suitable for housing modular switches, sockets, fan regulators etc including all necessary wall cutting chases and making good disturbed surfaces in cement mortar 1:3 and as per existing colour of white wash / paint / OBD / cement base paint complete all as specified and as directed. Note :- GI steel box and modular cover frame with plate shall deemed to be included in quoted rate against this item. For one light point controlled by one switch complete.

All as per serial item No 111.00 above but for one fan point controlled by one switch complete.

All as per serial item No 111.00 above but for one light point controlled by two way switchs complete.

All as per serial item No 111.00 above but for 3 pin 5 Amp socket outlet on the same board with other switch, sockets.

All as per serial item No 111.00 above but for 3 pin 5 Amp socket outlet independent complete.

All as per serial item No 111.00 above but for 3 pin 15 Amp socket outlet independent with 2.5 Sqmm copper conductor complete.

Modular switch one way 6 Amp,1 Modulecomplete all as specified.

Supplying and fixing for modular socket, 6 amps-2/3 pin combined, 2 Module complete all as specified.

Supplying and fixing for modular switch , one way, 16 amps, one Module complete all as specified.

Supplying and fixing for modular socket 16 amps-6 pin multipin, 2 Module complete all as specified.

Supply and fixing for modular switch 2 way 6 Amp,1 Modulecomplete all as specified.

Supply and fixing for modular Fan regulator electronic step type 230 V 2 Module complete all as specified.

Supply and fix in repairs Ceiling rose surface type, PVC/Polycarbonate islated body size 50x28 mm two to three terminalscomplete all as specified.

Supplying and fixing in repairs Modular white cover plate with frame, 2 Modulecomplete all as specified.

Supplying and fixing in repairs Modular white cover plate with frame, 4 Module complete all as specified.

Supply and fix for metal fiush mounting box 1/2 module complete all as specified.

Supply and fix for metal fiush mounting box 4 module complete all as specified.

Material and labour for wiring for circuit/ sub main wiring alongwith earth wire with the size of 2x1.5 Sqmm+1x1.5 Sqmm earth wire, PVC (FRLS) insulated copper conductor, single core, 1100 v grade cable in Concealed as required using following sizes of cables inciuding in PVC conduit.

All as per serial item No 123.00 above but 2x2.5 Sqmm+1x2.5 Sqmm earth wire.

All as per serial item No 123.00 above but 2x4.0 Sqmm+1x4 Sqmm earth wire.

All as per serial item No 123.00 above but 2x10 sqmm+1x10 Sqmm earth wire.

Supply and fixing for lamp holder insulated body with back plate for batten fitting complete all as specified.

Supply and fix for surface and wall mounted LED Batten 10W light fitting with decorative end caps LED lighting fixture delivers high brightness & excillent illumination with extruded Aluminium housing provided for heat resistant acrylic diffuser for glare free uniform light distribution powered by a external electronic constant current driver with no UV & IR radiation, energy efficient ready to use pack 10W LED complete with tube, & duly pre-wired and connecting up with 0.5 Sqmm 3 core flexible Copper cable cord from fitting to ceiling rose all as specified and directed by Engr-in-charge.

Supply and fix for surface and wall mounted LED Batten 20/24W light fitting with decorative end caps LED lighting fixture delivers high brightness & excillent illumination with extruded Aluminium housing provided for heat resistant acrylic diffuser for glare free uniform light distribution powered by a external electronic constant current driver with no UV & IR radiation, energy efficient ready to use pack 20/24 W LED complete with tube, & duly pre-wired and connecting up with 0.5 Sqmm 3 core flexible Copper cable cord from fitting to ceiling rose all as specified and directed by Engr-in-charge.

Supply and fix for 2'x2' 36W LED suitable for armstrong/grid/POP ceiling, 2x2 LED flat panel delivers high brightness & excillent illumination with extruded Aluminium housing provided for heat resistant frosted diffuser for glare free uniform light distribution powered by a external electronic constant current driver with no UV & IR radiation complete with seprate electronic driver & high brightness SMD LEDs, complete with connecting accesseries & Driver duly pre-wired and connecting up with 0.5 Sqmm 3 core flexible Copper cable cord from fitting complete all as specified and directed by Engr-in-charge.

Supply and fix for nero Surface mounted (Round) LED 18W downlighter with white powder coated aluminium die cast housing delivers high brightness & excillent illumination even in high ceiling areas with CRCA White powder coated provided for frosted heat resistant polycarbonate diffuser for glare free uniform light distribution powered by a separate electronic constant current driver with no UV & IR radiation, energy efficent surface mounted ready to use pack 18W LED, complete with connecting accesseries duly pre-wired and connecting up with 0.5 Sqmm 3 core flexible Copper cable cord from fitting complete all as specified and directed by Engr-in-Charge.

Supply and fix for LED Highway luminare 150 W -IP65 decorative oval edge LED lighting fixture comprising of pressure die cast housing with acrylic diffuser IP 65 protection, frosted heat resistant polycarbonate diffuser for glare free uniform light distribution powered by a inbuilt electronic constant current driver with no UV & IR radiation,energy efficent surface mounted ready to use pack 150W LED, complete with connecting accesseries duly pre-wired and connecting up with 0.5 Sqmm 3 core flexible Copper cable cord from fitting complete all as specified and directed by Engr-in-Charge.

Supply and fixing for freedom plus LED Street light 45 W made up of Pressure die cast aluminium housing with toughned glass and individual high power LEDs with secondary optics, IP65 protection complete with connecting accesseries duly pre-wired and connecting up with 0.5 Sqmm 3 core flexible Copper cable cord from fitting complete all as specified and directed by Engr-in-Charge.

Supply and fix for street light bracket 40mm bore GI pipe/tubing light grade 1.5 Mtr long band to shape with MS flat iron 50 x 5 mm for clamps nuts, bolts and washers etc and applying two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed.

Supply and fixing for sheet metal enclosure for DBs when MCBs to be used single pole and neutral single door, 240 volt without bus bar 2 way complete all as specified and directed.

Supply and fixing for sheet metal enclosure for DBs when MCBs to be used single pole and neutral with acrylic door IP 43 protection, 240 volt with 200 amps rated bus bar bar 4 way complete all as specified and directed.

Supply and fixing for sheet metal enclosure for DBs when MCBs to be used single pole and neutral with acrylic door IP 43 protection, 240 volt with 200 amps rated bus bar bar 8 way complete all as specified and directed.

Supply and fixing for sheet metal enclosure for DBs when MCBs to be used single pole and neutral with acrylic door IP 54 protection, 240 volt with 200 amps rated bus bar bar 12 way complete all as specified and directed.

Supply and fix for sheet metal enclouser distribution board 415volt,Vertical TPN 4 Way with provision for MCCB FP as incomer & MCBs as out going as per IS including compact insulated bus bar and rounded neutral bar, door earthing complete double door (Glazed) surface/reccess mounting IP-43 protection, , including connection with the existing sub circutis, electric meter etc with proper size new copper cable, lugs,connectors etc complete all as specified and directed.

Supply and fix for MCB SP 6 to 32 Amps 240 volts 10 KA C series complete all as specified and directed.

Supplying and fixing for MCB SPN 6 TO 32 Amps 240 volts complete all as specified and directed. .

Supplying and fixing for MCB SPN 40 to 63 Amps 240 volts 10 KA complete all as specified and directed.

Supplying and fixing for MCB SP 40 to 63 Amps 240 volts complete all as specified and directed.

Supply and fix for MCCB, 4 Pole ,breacking capacity 25 KA ,415 volts ,100 Amp including taking down unservicable one complete all as specified and directed.

Material and labour for down rod for ceilling fan of any make and sweep made out of medium grade GI tubing 15 mm dia with machine work duly painted with two coats of enamel paint and provision of holes for electric wire at top and bottom also arrangements for fittment of ceiling fan motor, clamp assembly and capacitor all specified and directed by Engineer-in-charge.

Disconnect and insulate electric supply wire and taking down carefully ceilling fan 1200mm/exhaust fan 380/300mm of any make dismantlling blades, servicing opening up of fan, motor, cleaning stator, rotor, cleaning of all parts greasing oiling of bushes and bearing reassembling and testing for smooth functioning for celling fan/exhaust fan, including replacement of 0.5 sqmm 3 core copper conductor flexible cable connected from celling rose to fan complete all as specified and directed by Engineer-in-Charge.

Material and labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick,burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level) with top edge of the plate not less than 1.5 Mtr below normal ground level,connected to galvanized iron wire of 4 mm dia earth lead by means of bolts,nuts ,washer and check nut of galvanized steel, earth wire protected by and including GI pipe 15 mm bore (light grade) and connected to main switch / MCB DBs box point as directed and including cement concret pit with CI cover 10 mm thick hinged to CI frame all as shown under electrical plate No 3 SSR Pt - I 2009 including painting the external surface of chamber & cover with enamel paint in diffrent colour as directed and writing earth results & date of test carried out with white paint on black painted background, wiremesh funnel, 20mm bore GI Pipe (Medium grade) for watering, charcoal and salt in alternative layers of 15cm thick all arround the electrode, including necessary excavation and earth work in any type of soil complete all as shown in electrical plate of SSR part -I and testing on completion all as directed.

shree balaji builders

D.N.Gupta and Sons

KUKREJA ENGINEERS