Loading
Loading…
Loading…
Tender Value
₹3.9 Cr
EMD Value
₹7.9 L
Closing Date
12 Oct 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
WORKS 2
14 conditions · 3 needing a document upload
Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or "V" whichever is less; Where V=Advertised value of the tender in crores of Rupees, N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Electrical contractor license: - The contractor should have valid electrical contractor license issued by government and submit along with tender document. If valid electrical contractor license is not submitted along with tender document, then offer will be summarily rejected
Technical Eligibility Criteria: (a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender. The Definition of similar nature in this tender means "Any Electrical work related to HT/LT installations". (Authority: PCEE / NWR / JP letter No EL/50/0/SNW/Vol.I Dtd. 08.01.2016).
3 conditions · 1 needing a document upload
Bidder / Tenderer should submit GST registration certificate along with PAN card & Bank mandate while bidding / uploading tender documents
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
I / We have visited the works site and I / We am / are aware of the site conditions.
Electric Work in connection with (i)Provision of additional new platform no. 4 & 5, Extension of existing FOB & Second entry at Jaisalmer station.(ii) Provision of two running line cover shed & cat walk on both pit line at Jaisalmer Station. (iii) Construction of 01 no. pit line with associated facilities at JSM.
GSUELECTG-11Rof2026-27~NWR
GSUELECTG-11Rof2026-27
Open
Works - General
12 Months
Jodhpur, Rajasthan
₹0
₹7.9 L
18 Sept 2026
18 Sept 2026
28 Sept 2026
239 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 3,93,63,514.19 | ||
| — | 2.00 | — | — | ||
| Supply, erection, testing and commissioning of 1000KVA11/0.440 V 3 Phase 50HZ transformer and specification(Inspection: RITES, Inspection Charges: To be borne by Contractor) | — | — | — | 38,51,520 | |
| — | 2.00 | — | — | ||
| Supply of material, fabrication &erection of 'H' pole (Double pole)with I section M.S. beam ISHB150, size150mmx150mm of length 10.0 Mtrs. with required foundation and painting etc. (As per specification)(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 89,177.62 | |
| — | 6.00 | — | — | ||
| Supply and fixing of Isolator11KV, 400A without EB & with Post insulator (G/O Switch, Horizontal type) on existing H-Pole. (As per specification(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 1,55,724.12 | |
| — | 6.00 | — | — | ||
| Supply & fixing of 11KV Horn gap fuse hardware with post insulators (D/O fuse). (As per specification)(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 49,402.38 | |
| — | 5.00 | — | — | ||
| Supply, fixing, testing and commissioning of Lighting arrestors. (As per specification) (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 30,316.15 | |
| — | 6.00 | — | — | ||
| Supply, erection, testing and commissioning of 33/11KV,Disc/Pin insulator on SP/DP. (As per specification)(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 3,450.78 | |
| — | 32.00 | — | — | ||
| Supply, fixing and commissioning HT 11 KV XLPE heat shrinkable HT Cable end box indoor type Suitable for Cable Size 70/95 sq.mm. As per specification(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 3,21,804.8 | |
| — | 32.00 | — | — | ||
| Supply, fixing and commissioning HT 11 KV XLPE heat shrinkable HT Cable end box outdoor type Suitable for Cable Size 70/95 sq.mm. As per specification(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 4,11,661.44 | |
| — | 30.00 | — | — | ||
| Rubber Mat (ISI Mark) non-stick type suitable for 11KV AC Supply of size :2000x1000x25mm. (As per specification)(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 34,286.1 | |
| — | 4.00 | — | — | ||
| Supply, installation & erection of stay rod/sturt complete. (As per specification) (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 5,035.68 | |
| — | 10.00 | — | — | ||
| Supplying & erection of shock Restoration Chart in glass frame.(As per specification) (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 930.4 | |
| — | 50.00 | — | — | ||
| Supply, fixing of LT Heat shrinkable Straight through Joint size (35 sq mm to 185 sq mm)as per specification(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 1,11,700 | |
| — | 15.00 | — | — | ||
| Supply, fixing and commissioning HT 11 KV XLPE heat shrinkable HT Cable end box outdoor type Suitable for Cable Size 185 sq.mm. as per specification.(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 1,26,325.2 | |
| — | 4.00 | — | — | ||
| Supply, fixing and commissioning HT 11KV XLPE heat shrinkable HT cable end box outdoor type suitable for cable size 120sqmm(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 32,693.04 | |
| — | 15.00 | — | — | ||
| Supply fixing and commissioning of HT XLPE heat shrinkable type cable end box indoor type size50 to 185 sqmm as per specification(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 95,083.35 | |
| — | 1.00 | — | — | ||
| Supply, erection, testing and commissioning of one set of 3panel vacuum circuit breaker630/800 Amp for 11 KV System as per specification(IInspection-RITES , Inspection Charges - To be borne by Railway)) | — | — | — | 13,17,208.62 | |
| — | 5.00 | — | — | ||
| L.T. Panel-I Manufacturing, supplying, testing and commissioning of wall/floor mounted (as per site requirement) LT Distribution board with 01 No. 200 Amp. 4pole 415 Volt, 50 Hz, thermal magnetic MCCB as incoming and02 No.100 Amp. 4 pole MCCB,03 Nos. 40 Amp. 4 pole MCCB as outgoing. (As per Specification attached)Inspection-RITES , Inspection Charges - To be borne by Railway) | — | — | — | 5,93,033.7 | |
| — | 1.00 | — | — | ||
| Manufacturing, supplying, testing and commissioning of LT Panel with incomer 1250 Amp. ACBs 2 Nos., outgoing ACB1250A 01no, 400A MCCB 2nos.,250A MCCB 4 nos, 125A MCCB 2nos as per specification.Inspection-RITES ,( Inspection Charges - To be borne by Railway) | — | — | — | 18,87,000 | |
| — | 2.00 | — | — | ||
| L.T. Panel-III Manufacturing, supplying, testing and commissioning of LT Panel with incomer 800 Amp. ACBs 1 no. and outgoing 400A MCCBs 4nos., 250A MCCBs 4 nos & 100AMCCBs 3 nos as per specification (Inspection-RITES , Inspection Charges - To be borne by Railway) | — | — | — | 11,42,489.62 | |
| — | 1.00 | — | — | ||
| Supply, installation, testing &commissioning of MDB with three phase electronic Energy meter, digital ampere meter with CT, selector switch, suitable digital voltmeter and indication lamp with following incoming &outgoing Incoming MCCB 4 pole400A,35KA 2 Nos. Outgoing MCCB 4 pole 250A, 35KA06Nos.(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 3,36,900.09 | |
| — | 180.00 | — | — | ||
| Supply of material & wiring of sub-main with 2x6 sq mm PVC insulated multi-strand ( 84 /.30 mm ) copper conductor cable in existing laid ( surface / recessed ) PVC conduit pipe and continuous running of PVC insulated copper earth wire of 1 Sq.mm. as per specifications attached as required(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 22,611.6 | |
| — | 720.00 | — | — | ||
| Supply of material & wiring of sub-main with 2x4 sq mm PVC insulated multi-strand ( 56 /0.3 mm ) copper conductor cable in existing laid ( surface / recessed ) PVC conduit pipe and continuous running of PVC insulated copper earth wire of 1 Sq.mm as per specifications attached as required (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 64,008 | |
| — | 100.00 | — | — | ||
| Wiring of main (for individual qtr.) with 2x4 sq mm 56/.30 PVC insulated multi-strand copper cable in 19/20 mm dia MS conduit pipe to be fixed properly with saddles, gutties & other fixtures and continuous running of PVC insulated copper earth wire as per specifications attached. Including supply of material as required.(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 13,017 | |
| — | 2700.00 | — | — | ||
| Supply of material & wiring of sub-main with 2x2.5 sq mm PVC insulated ( 36 /0.3 mm ) multi-strand copper conductor cable in existing laid ( surface / recessed ) PVC conduit pipe and continuous running of PVC insulated copper earth wire of 1 Sq.mm. as per specifications attached as required(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 1,88,514 | |
| — | 3300.00 | — | — | ||
| Supply and Fixing of 20 mm dia medium class P.V.C. Pipe along with accessories as required in recess on walls/roof properly including cutting of wall /roof and making good the damages as per specifications attached (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 2,68,257 | |
| — | 450.00 | — | — | ||
| Supply and Fixing of 20 mm dia medium class PVC Pipe along with accessories as required in surface on walls/roof properly with saddles and wooden gutties etc. complete as per specifications attached (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 23,967 | |
| — | 150.00 | — | — | ||
| Supply of material & commissioning of PVC casing caping 25X12 mm with accessories for surface wiring as per specification (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 3,673.5 | |
| — | 450.00 | — | — | ||
| Supply of material and wiring of LP/TP/FP/Ex. Fan point with 1.5sqmm PVC single core multi-stranded copper wire insulated concealed in stone/brick masonry wall in19/20 mm PVC conduit with1.5sqmm PVC wire insulated copper for earth wire 1-way /2-way switch 5/6A as required and good quality ceiling rose including connection. This item includes modular switch, modular ceiling rose, PVC conduit and required chase as per site requirement.(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 1,73,758.5 | |
| — | 30.00 | — | — | ||
| Supply and fixing 2 module modular switch board plate for fixing of modular switches -plug with sheet metal box of good quality concealed fixing of MS/PVCas per site requirement(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 4,262.7 | |
| — | 30.00 | — | — | ||
| Supply and fixing 3 module modular switch board plate for fixing of modular switches -plug with sheet metal box of good quality concealed fixing of MS/PVC as per site requirement (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 6,187.5 | |
| — | 30.00 | — | — | ||
| Supply and fixing 4 module modular switch board plate for fixing of modular switches -plug with sheet metal box of good quality concealed fixing of MS/PVC as per site requirement (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 6,518.7 | |
| — | 40.00 | — | — | ||
| Supply and fixing 6 module modular switch board plate for fixing of modular switches -plug with sheet metal box of good quality concealed fixing of MS/PVC as per site requirement(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 9,485.2 | |
| — | 30.00 | — | — | ||
| Supply and fixing 8 module modular switch board plate for fixing of modular switches -plug with sheet metal box of good quality concealed fixing of MS/PVC as per site requirement (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 9,910.5 | |
| — | 20.00 | — | — | ||
| Supply and fixing 12 module modular switch board plate for fixing of modular switches -plug with sheet metal box of good quality concealed fixing of MS/PVC as per site requirement(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 6,977.2 | |
| — | 20.00 | — | — | ||
| Supply and fixing ceiling of modular (2 module) fan regulator electronic type 5-step (suitable for BLDC fan)as per specification (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 8,903.4 | |
| — | 85.00 | — | — | ||
| Supply and fixing 5/6A plug, modular 3/5-pin 230Vincluding modular switch in the modular board and connection as per site requirement (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 23,160.8 | |
| — | 30.00 | — | — | ||
| Supply and fixing 15/16Aplug, modular 6-pin 230Vincluding modular switch in the modular board and connection as per site requirement (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 9,200.4 | |
| — | 215.00 | — | — | ||
| Supply, install, test & commission of Modular blank plate as per specification (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 2,719.75 | |
| — | 520.00 | — | — | ||
| Wiring of shed LP/TP in covered shed with 1.5sqmm copper wire PVC insulated & multi-stranded in PVC conduit, ISI mark 1.5mm thick, size19/20mm dia and 1.5sqmm PVC insulated multi stranded copper earth wire with ceiling rose fixed with saddles or tied properly and junction box as per spec. (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 97,723.6 | |
| — | 40.00 | — | — | ||
| Supply, fixing and connecting modular type exhaust fan 225/250mm as per spec (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 33,216.4 | |
| — | 30.00 | — | — | ||
| Supply, install, test & commission of Ray roll plug socket 20amp SPN Ray Roll Plug socket including connection /wiring of "C" series 32 amps SP-MCB as per specification. (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 26,876.7 | |
| — | 40.00 | — | — | ||
| Supply of Phenolic top sheet wooden board size 7'' x 4'' with one no. 5x15 amp switch socket combined & one nos. 5 amp switch ISI mark make-Anchor/Vinay/ABB/Cona/Legrand as per specification (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 5,400 | |
| — | 20.00 | — | — | ||
| Supply of Phenolic top mobile charging wooden board size 6''x15'' fitted with 4 nos. switch & 4 nos. socket of 6 amps with internal wiring of 1.5 sq. mm with base plate of both side particle board for mobile with hanging clip as per specification (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 6,960 | |
| — | 160.00 | — | — | ||
| Supply, Fixing of MCB to be provided in the MCBDB given above including supply of material as required & as per specifications attached-MCB (SP-) 6-32 A (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 38,464 | |
| — | 25.00 | — | — | ||
| Supply, Fixing of MCB to be provided in the MCBDB given above including supply of material as required & as per specifications attached-RCCB - 25 A/30mA (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 63,363 | |
| — | 40.00 | — | — | ||
| Supply. fixing, testing and commissioning of SPN DB 8-way with provision of incoming MCB of 63A,IP 43/IK09, double door at suitable locations. (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 1,02,508 | |
| — | 9.00 | — | — | ||
| Supply, Fixing, testing and commissioning of TPN DB 8-way with provision of incoming MCCB of 125A, IP43/IK09, double door at suitable locations (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 1,38,770.82 | |
| — | 8.00 | — | — | ||
| Supply, Fixing of MCB to be provided in the MCBDB given above including supply of material as required & as per specifications attached- MCCB 4-pole 100/125A, 25 KA (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 1,11,071.2 | |
| — | 20.00 | — | — | ||
| Supply, fixing, testing and commissioning of fabricated Feeder Pillar distribution box made of MS sheet 1.6mmthick size 600x300x600mmwith suitable MS stand Copper bus bar of 200Acapacity and 2x63A MCB 4pole as per spec (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 1,16,812.8 | |
| — | 40.00 | — | — | ||
| J' type cable route marker made of cast iron as per approved Railway drawing (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 8,692.8 | |
| — | 2.00 | — | — | ||
| Supply, installation, testing & commissioning of VTPN type metal double door type 8 way DB with having 01 No. 250Amp., 4 pole MCCB, 36 KA as incomer & 8 Nos. TP MCB, 10KA'C' curves, 40-63 Amp. Cap. As outgoing having suitable IP-54,IK-09protection (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 1,04,231.3 | |
| — | 36.00 | — | — | ||
| "B" Class 50 mm dia GI pipe earth Station with digging pit & refilling with charcoal & salt as per specification. (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 49,879.08 | |
| — | 36.00 | — | — | ||
| Inspection Chamber with cover as per specification (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 13,911.84 | |
| — | 360.00 | — | — | ||
| Supply & laying of earth connection from earth electrode with 4 mm GI wire properly fixed on wall with wooden gutties etc. as required (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 4,222.8 | |
| — | 9.00 | — | — | ||
| Supply and providing copperplate earthing 4.0 m deep size600x600x3mm with 3.5m longG.I. "B" class pipe 38 mm for pouring water with 50 Kg charcoal and 10 Kg salt including RCC/masonry earth enclosure with pull out handle and 25x3mm copper flat earth strip 4.0mtrs long from earth pit bottom riveted to earth top . The earth value to be measured and marked on earth pit and as per specification attached (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 78,900.75 | |
| — | 240.00 | — | — | ||
| Supply and fixing copper earth strip 25x3 mm and as per specification attached (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 1,01,726.4 | |
| — | 2000.00 | — | — | ||
| Supply of cable 3Cx185sqmm, HT 11KV XLPE HT Cable as per specification (Inspection-RITES , Inspection Charges - To be borne by Railway) | — | — | — | 27,11,640 | |
| — | 1000.00 | — | — | ||
| Supply of cable 4Cx300 sqmm, LT XLPE Cable as per specification (Inspection-RITES , Inspection Charges - To be borne by Railway) | — | — | — | 17,26,940 | |
| — | 1000.00 | — | — | ||
| Supply of cable 4Cx240 sqmm, LT XLPE Cable as per specification (Inspection-RITES , Inspection Charges - To be borne by Railway) | — | — | — | 13,96,000 | |
| — | 500.00 | — | — | ||
| 3 Core 2.5 sq. mm PVC Copper Circular Sheathed Cable with Rigid Conductor (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 57,735 | |
| — | 3000.00 | — | — | ||
| Supply of cable 4Cx70 sqmm, LT XLPE Cable as per specification (Inspection-RITES , Inspection Charges - To be borne by Railway) | — | — | — | 13,50,000 | |
| — | 1000.00 | — | — | ||
| Supply of XLPE insulated, PVC sheathed armoured Aluminium multistrand conductor cable 1100V grade, as per specification attached. 4 Core 35 sq mm(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 2,70,000 | |
| — | 3000.00 | — | — | ||
| Supply of XLPE insulated, PVC sheathed armoured Aluminium multistrand conductor cable 1100V grade, as per specification attached. 4 Core 16 sq mm (Inspection-RITES , Inspection Charges - To be borne by Railway) | — | — | — | 5,40,000 | |
| — | 3500.00 | — | — | ||
| Supply of XLPE insulated, PVC sheathed armoured Aluminium multistrand conductor cable 1100V grade, as per specification attached. 4 Core120 sq mm (Inspection-RITES , Inspection Charges - To be borne by Railway) | — | — | — | 23,27,500 | |
| — | 5000.00 | — | — | ||
| Digging and filling of trench size 0.4 x 0.8 mtr as per spec ( trench work may be on kuchcha/ pucca land and all type of soil as per site requirement and without protective layer of brick). Surface of trench shall be made good in all respect and satisfaction of site engineer. (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 2,03,450 | |
| — | 1000.00 | — | — | ||
| laying cable in Air/Wall/Pole with fixture(02 nos. per mtrs) as per specification (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 24,320 | |
| — | 100.00 | — | — | ||
| Supplying., laying of GI pipe size 50 mm dia. B class as per IS1239 for cable use as per specification enclosed (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 34,426 | |
| — | 30.00 | — | — | ||
| Supplying., laying of GI pipe size 100 mm dia. B class as per IS1239 for cable use as per specification enclosed (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 20,251.8 | |
| — | 4000.00 | — | — | ||
| Supply &laying of HDPE pipe of75/80mm dia, wall thickness3mm. The work involveslaying of HDPE pipe & laying cable in HDPE pipe. As per specification (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 4,11,120 | |
| — | 1020.00 | — | — | ||
| Drilling of horizontal bore below track/road by pushing method for laying of RCC/HDPE/DWC pipe of various sizes (As per specifications) (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 14,52,888 | |
| — | 1300.00 | — | — | ||
| Supply & laying of HDPE pipe, dia 160 mm under road/ground/floor/railway track or as per site requirement in already excavated trench. (As per specification)(Inspection-RITES , Inspection Charges - To be borne by Railway) | — | — | — | 10,27,208 | |
| — | 1300.00 | — | — | ||
| Laying, connecting & commissioning of cable in pipe/trench etc. with complete lug, glands & transportation of cable etc. as per specification (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 3,14,743 | |
| — | 1.00 | — | — | ||
| Supply, install, test & commissioning of load change over switch in steel sheet enclosure 250 Amp. (as per specification)(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 12,350.65 | |
| — | 1.00 | — | — | ||
| Supply, install, test & commissioning of load change over switch in steel sheet enclosure 630 Amp. (as per specification) (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 24,726.08 | |
| — | 20.00 | — | — | ||
| Supply, fixing, testing and connecting of wall mounted heavy duty Air Circulator of 24''(600mm) size with built in 3 speed regulator, delivers Air 280Cu.m/min, similar to M/s Almonard make with all accessories complete confirming to IS specification with latest amendments. The Air Circulator is to be fixed by suitable MS clamps of size 50x50x6mm / flats of size 40x6mm with bolts and nuts etc., complete as desired by site engineer (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 2,01,962.2 | |
| — | 35.00 | — | — | ||
| Supply, Testing & Fixing of wall mounted cabin fan with regulator three speed, suitable for 220- 230 volt ,50HZ AC supply .Model No-Media BW 04 of Bajaj or similar to Usha/ Crompton Greaves /Philips .(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 68,828.9 | |
| — | 22.00 | — | — | ||
| Installation & commissioning of 1.5 Ton split AC including supply & fixing of 3 meter copper pipe, stand suitable for outdoor unit, drilling hole & necessary accessories as per site requirement. (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 96,032.2 | |
| — | 95.00 | — | — | ||
| Supply and provide MS flat of iron size40x3mm with spacers and fixing clamps as per spec (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 14,003 | |
| — | 50.00 | — | — | ||
| Fixing of ceiling fan with clamp, hooks and down rod as per requirement and connection as per spec (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 9,268.5 | |
| — | 8.00 | — | — | ||
| Supply, fixing, testing and commissioning of Distribution Board double door, 3-phase and neutral with incoming 63A 4-pole MCB and outgoing 12Nos. MCB 6-32A single pole as per spec. (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 40,431.44 | |
| — | 300.00 | — | — | ||
| Supply and fixing casing caping of PVC size 75x75mm and 2mm thick with suitable nut bolts for fixing or tied with copper wire 14swg for 5/7 nos.of copper wire & earth wire as per spec.(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 41,748 | |
| — | 1000.00 | — | — | ||
| Supply, laying and fixing five wire of PVC copper cable size10sqmm flame retardant, low smoke single core insulated unsheathed multi-stranded copper conductor, voltage grade 1.1KV(1100 v) conf to IS694-1990or latest in five with one no 8SWG copper earth wire as per spec (Inspection-RITES , Inspection Charges - To be borne by Railway) | — | — | — | 5,56,430 | |
| — | 100.00 | — | — | ||
| Supply of material with excavation & commission of foundation for pole/panel (C.C. Platform ) etc . As per specification (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 2,51,087 | |
| — | 5.00 | — | — | ||
| Erection of 7 mtrs high single arm hot dip galvanized Steel Octagonal "Smart poles" with galvanized base plate of 220 x 220 x 12 mm Foundation PCD 205 & Bolt size (4x20 mm dia X 700 mm) length in position including excavation of pit and filling the same with concrete 50 cm ground level from base plate mounting including supply of material as required The pole shall be galvanized internally & externally by single dipping method .Make BAJAJ Model BOP -7030, GE, Crompton Greaves, Philips or similar to this model.(Inspection- Consignee , Inspection Charges - None ) | — | — | — | 61,576.3 | |
| — | 40.00 | — | — | ||
| Supply fabrication, erection, testing and commissioning of G.I. octagonal pole 5 mtrs. long double arm suitable for street light fixture, 2 x 14w/4 x 14 w including digging of pit, making foundation and muffing with cement, concrete 1:2:6. As per specification (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 4,16,945.6 | |
| — | 2.00 | — | — | ||
| Supplying, fixing ,testing & commissioning Automatic operation street light timing switch box having lighting control (on-off) through astronomical calculation and pre-wired with suitable size of contactors, copper conductor etc. at specified locations as per specification attached and Similar to model no 04764 of LEGRAND make or similar of Siemens/ABB (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 41,803.2 | |
| — | 300.00 | — | — | ||
| Assembling, fixing, hanging and making connection of Surface pendent mounted box type tube light fitting/street light fitting as per specification (Inspection- Consignee , Inspection Charges - None ) | — | — | — | 21,957 | |
| — | 200.00 | — | — | ||
| Design, manufacture, display of wall /hanging / floor mounting type LED illuminated sign / direction boards in half elliptical shape. The display sheet shall be of unbreakable 040 translucent polycarbonate sheet of 2 mm thickness. The text / graphics matter visibility shall not be less than 160 deg. The approved colour text and graphics shall be printed / router cut on monomeric calendared vinyl of 70 um thickness and shall be firmly pasted on display sheets. The mounting arrangement shall be hanging, wall mounting, ceiling mounting, pole mounting or floor mounting and as per site requirement. The signage shall have the integral mounting arrangements with sturdy structural frame and ACP cladding on the back side of the signage to avoid rusting and entry of dust. The LED board shall have uniform illumination with 4-8 W / sq. ft and with brightness more than ambient light. Suitable size end cap of 1.5 (Inspection-RITES , Inspection Charges - To be borne by Railway) | — | — | — | 6,74,736 | |
| — | 200.00 | — | — | ||
| Erection and installation of wall /hanging / floor mounting type LED illuminated sign / direction boards in half elliptical shape. The display sheet shall be of unbreakable 040 translucent polycarbonate sheet of 2 mm thickness. The text / graphics matter visibility shall not be less than 160 deg. The approved colour text and graphics shall be printed / router cut on monomeric calendared vinyl of 70 um thickness and shall be firmly pasted on display sheets. The mounting arrangement shall be hanging, wall mounting, ceiling mounting, pole mounting or floor mounting and as per site requirement. The signage shall have the integral mounting arrangements with sturdy structural frame and ACP cladding on the back side of the signage to avoid rusting and entry of dust. The LED board shall have uniform illumination with 4-8 W / sq. ft and with brightness more than ambient light. Suitable size end cap of 1.5 mm thick SS 304 should be provided (Inspection: Consignee, Inspection Charges: None) | — | — | — | 67,472 | |
| — | 2.00 | — | — | ||
| Supply, erection, testing & commissioning of 12.50 Mtrs. high mast shaft totally hot dip galvanized and suitable for wind velocity as per IS 875 PART 3. The mast shaft shall be in two finished section. it shall also include accessories for 12.5 Mtrs. high mast including head frame, steel wire rope 6 mm dia. (7/19 construction ) double drum winch, galvanized lantern carriage arrangement suitable for 6 luminaries symmetrically and its control gear boxes and lighting finial with integral power tool. The work also include design and casting of suitable foundation bolts with M-15 Concrete for high mast considering the safe soil bearing capacity at site as 10T per Sq. mm at 2 Mtrs. depth. the foundation should be casted with foundation bolt manufactured with special steel along with nuts, washers, anchors plates and templates as required make: BAJAJ/PHILIPS. The mast shall have one longitudinal weld and single dipping (hot dip galvanized) per section (as per specification attached).(Inspection: Consignee, Inspection Charges: None) | — | — | — | 3,18,450.3 | |
| — | 2.00 | — | — | ||
| Supply & installation of control panel housing suitable timer contactor circuit for Automatic switch ON & switch OFF of the mast at a preset time. (Inspection: Consignee, Inspection Charges: None) | — | — | — | 36,161.96 | |
| — | 4.00 | — | — | ||
| Supply and fixing of aviation light luminaires of BGAV 302 LED of Bajaj or similar comprising of aluminium housing with polycarbonate enclosure (1 fitting per mast is necessary if no taller structures are in the vicinity). Fitting should be of reputed make and as per tech. spec. (Inspection: Consignee, Inspection Charges: None) | — | — | — | 17,094.28 | |
| — | 1700.00 | — | — | ||
| Supply, erection and commissioning of auxiliary cable tray made from angle 35x35x5 mm and MS plate 35x5 mm to be fixed on already grouted MS bolts on the pillar/ platform or washing line of 260 mm vide & (as per technical specification attached.) (Inspection: RITES, Inspection Charges: To be borne by Railways) | — | — | — | 15,49,771 | |
| — | 1000.00 | — | — | ||
| Supply of XLPE insulated, PVC sheathed armoured Aluminium multistrand conductor cable 1100V grade, as per specification attached.2 Core 120 sq mm (Inspection: Consignee, Inspection Charges: None) | — | — | — | 3,41,700 | |
| — | 1.00 | — | — | ||
| Design, manufacture, supply, testing and commissioning of constant currently constant voltage charger for VRLA as per Spec (Inspection: Consignee, Inspection Charges: None) | — | — | — | 4,89,700 | |
| — | 55.00 | — | — | ||
| Fabrication, supply, fixing and commissioning of Battery charging board /box emergency terminal box two ways outdoor type as per RDSO Drg. No. SKE-3929 as per specifications attached. (Inspection: Consignee, Inspection Charges: None) | — | — | — | 46,788.5 | |
| — | 38.00 | — | — | ||
| Supply, erection, testing and commissioning of pre-cooling points having BCH 500 volt 63 A plug switch unit combined set (male-female both) including aluminium four pole bus bar chamber of 250 Amps capacity complete inside MS enclosure having suitable design for incoming and outgoing 3.5 or 4 core 120 sq. mm XLPE cable with earthing of the pre-cooling point as per the detailed technical specification and site requirement this item includes the supply of 63 amp. MCCB 4pole. size of MS box (70 x40x30mm)as per site requirement and drawing Inspection: RITES, Inspection Charges: To be borne by Railways) | — | — | — | 6,77,959.14 | |
| — | 200.00 | — | — | ||
| Unbranded 2 mtr Cable ducting system, Model- Cable Trunking and Ducting system for Electrical Installations 75x75 (Inspection: Consignee, Inspection Charges: None) | — | — | — | 94,100 | |
| — | 200.00 | — | — | ||
| CABLE DUCT A45(H)X45(W) ALONG WITH DUCT COVER A45 IN LENGTH OF 1 METERSTANDARD SLOT GREY OF M/S L&T, PHONEIX, PANDUIT MAKE or similar(Inspection: Consignee, Inspection Charges: None) | — | — | — | 27,600 | |
| — | 40.00 | — | — | ||
| Supply, installation, testing & commissioning of (150 mm width x 50 mm depth x 1.6 mmthickness) perforated Hot Dipped Galvanized Iron Cable Tray (Galvanization thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections fixed with MS Angle frame duly painted of 35 mm x 5 mm thick and all hardware complete in all respect.(Inspection: Consignee, Inspection Charges: None) | — | — | — | 27,999.6 | |
| — | 40.00 | — | — | ||
| Supply, installation, testing & commissioning of (100 mm width x 50 mm depth x 1.6 mmthickness) perforated Hot Dipped Galvanized Iron Cable Tray (Galvanization thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections fixed with MS Angle frame duly painted of 35 mm x 5 mm thick and all hardware complete in all respect (Inspection: Consignee, Inspection Charges: None) | — | — | — | 25,960 | |
| — | 1000.00 | — | — | ||
| supply of XLPE Cable 10 sq. mm 4 Cores copper cable (Inspection: RITES, Inspection Charges: To be borne by Railways) | — | — | — | 8,75,600 | |
| — | 500.00 | — | — | ||
| Digging of pacci (Pakki) trench as per specification (Inspection: Consignee, Inspection Charges: None) | — | — | — | 1,46,375 | |
| — | 6.00 | — | — | ||
| Supply, fixing, testing and commissioning of RCBO 25A,RCBOdouble pole, 30mA with Earth leakage, overload and short circuit protection as per spec (Inspection: Consignee, Inspection Charges: None) | — | — | — | 12,753.18 | |
| — | 2.00 | — | — | ||
| Supply, fixing, testing and commissioning of RCBO 63A,RCBO Four pole, 30mA with Earth leakage, overload and short circuit protection as per spec (Inspection: Consignee, Inspection Charges: None) | — | — | — | 6,701.72 | |
| — | 6.00 | — | — | ||
| Supply. fixing, testing and commissioning of SPN DB 12-way with provision of incoming MCB of 63A,IP 43/IK09, double door at suitable locations. (Inspection: Consignee, Inspection Charges: None) | — | — | — | 8,384.46 | |
| — | 402.00 | — | — | ||
| Supply installation testing commissioning of LED based pit lights (3 directional type) fitting16/20W suitable for 48V-72V, Single phase AC supply ingress protectionIP-67, as per spec attached. (Inspection: RITES, Inspection Charges: To be borne by Railways) | — | — | — | 14,55,131.46 | |
| — | 250.00 | — | — | ||
| Supply installation testing commissioning of 22 Watt catwalk LED light fittings as per the following description/specification/dimensions. i) Dimension of the fitting (in mm approx.): L-290 X B-210 X H-75 ii)Housing: PDC aluminium iii)Mounting: Surface/recessed iv)Voltage: 48volt AC +/- 10% v)Wattage:22 watt+/-10% vi)IP-67vii) IK-10 viii) LED type: SMD ix)Protection: Reverse polarity protection, Short circuit protection, Open circuit protection. MAKE-GOLDWYN OR SIMILAR as per spec (Inspection: RITES, Inspection Charges: To be borne by Railways) | — | — | — | 8,91,292.5 | |
| — | 35.00 | — | — | ||
| Supply, installation, testing &commissioning of cable junction boxes IP 65 of various cable sizes with metric knockouts for cable entry Box dimensions (LxBxH)(mm): 200x160x98 with 100 Amp copper bus bar including other required materials for fixing, mounting & masonry work if required. (Inspection: Consignee, Inspection Charges: None) | — | — | — | 1,32,682.9 | |
| — | 9.00 | — | — | ||
| Supply, installation, testing &commissioning of 02 kVA step down transformer i/p 230V, o/p-40-72 Volt AC , 50HZ outdoor type. As per specification (Inspection: Consignee, Inspection Charges: None) | — | — | — | 67,977.54 | |
| — | 182.00 | — | — | ||
| Supply, fabrication, installation &commissioning of junction box for through cable & tapping of fittings with gland & 25x3mm strip. As per specification (Inspection: Consignee, Inspection Charges: None) | — | — | — | 50,554.14 | |
| — | 20.00 | — | — | ||
| Supply, fabrication, installation & commissioning of junction box with "B series MCB and RCCB for incoming supply control. As per specification (Inspection: Consignee, Inspection Charges: None) | — | — | — | 36,584 | |
| — | 300.00 | — | — | ||
| Supply, fixing of PVC cable duct40X60 (W X H) 1M STD slot grenish gray of standard make. As per specification (Inspection: Consignee, Inspection Charges: None) | — | — | — | 29,520 | |
| — | 1.00 | — | — | ||
| Supply, installation. Testing &commissioning of 1000KVA outdoor type 11KV/750VDYN 11. ONAN connected transformer on suitable foundation and with fencing 4Mtr x 4 Mtr ( approx.) as per spec (Inspection: RITES, Inspection Charges: To be borne by Contractor) | — | — | — | 15,99,967.08 | |
| — | 20.00 | — | — | ||
| Terminating of cable of size 120sqmmsingle core copper XLPE sheathed cable with lugs and PVC cable gland as per spec.(Inspection: Consignee, Inspection Charges: None) | — | — | — | 10,803.2 | |
| — | 2.00 | — | — | ||
| Supply installation, testing and commissioning of double ended jumper plug assembly with 10Mtr Polyamide conduit and 120sqmm cable for phase and 95sqmm cable for neutral suitable for LHB type coupler 400Amps/ 750Volts capacity MCCB with enclosure as per spec (Inspection: Consignee, Inspection Charges: None) | — | — | — | 4,06,228.44 | |
| — | 2.00 | — | — | ||
| Supply ,Installation , Testing and Commissioning of LHB type Socket Assembly 500AmpHoused in stainless steel housing of size 3feet x 2feetx 2feet (approx.) with one contractor AF/750- 415coil volt, One Aux contactor 16Amp- 110VDC coil voltage, 16 pin UIC coupler socket assembly , 100VA750/110VAC Transformer and 5Amp 110V AC to110VDC AC to DC converter and ON/OFF push button set with fixing stand to be fixed in cement concrete foundation as per technical specification (Inspection: RITES, Inspection Charges: To be borne by Railways | — | — | — | 7,19,452.56 | |
| — | 1.00 | — | — | ||
| Battery Charging rectifier set complete with all accessories having, earthing connection and masonry works e.t.c. as required. at site. The Rectifier set shall have 2 set of Knife Switches as outgoing as per specifications attached Input- 3 phase 415 Volts A.C. Output -110 volt to 150 volt 200 Amp. D.C. (Inspection: Consignee, Inspection Charges: None) | — | — | — | 2,23,389.43 | |
| — | 4.00 | — | — | ||
| Supply of material, fabrication, installation and commissioning of Rolling in Examination lighting MS box of suitable dimensions as per specifications attached at specified locations (Inspection: Consignee, Inspection Charges: None) | — | — | — | 23,644.6 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
ACS1TO12newCOMPRESSED.pdf
ATTACHMENT
SORTECHNICALSPEC GSU11Rof202627
ATTACHMENT
TDGSU11Rof25-26.pdf
ATTACHMENT
SORTECHSPECJSMworkGSU11Rof26-27.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .