SPECIAL REPAIR TO OR MD ACCN BLDG NO P 252 OF ABDUL HAMID VIHAR AT MIL STN GANDHINAGAR

Amount

Removing rubbish to a distance exc. 1.5 Km but not exc. 5.0 Km out side MD land complete all as specified and directed.

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate precast cement concrete kerb stone jointed in CM 1:4 complete all as specified and directed.

M&L for pre cast cement concrete 1:2:4 type B0 using 12.50mm graded stone aggregate as in loures and jallies, 35mm thick (measured solid) including all moulding but excluding frame, set in cement mortar 1:4 complete all as specified and directed.

M & L for reinforced cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. Note:- Reinforcement shall be measured and paid separately under respective item of BoQ.

Supply only, liquid water proofing compound mixed as per manufacturer instructon mixed in cement concreter or cement mortar complete all as specified and directed.

M&L for old size fly ash Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for fly ash Brick work with old size, sub class 'B' bricks, straight or curved on plan any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

Cutting chases, pinning in, for brick walls, making good to facings for concealed water tubing etc. cutting exceeding 10cm but not exceeding 20cm girth complete all as specified and directed.

M&L for cutting holes into or through brick walls built in cement mortar or cement lime mortar and making good in cement mortar 1:3 or cement concrete 1:2:4, type B-l as required, superficial area not exceeding 150 sq. cm including necessary scaffolding, if required complete all as specified and directed.

Rough finished flat form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exce 200 mm thick.

S&F, 35 mm thick, 2nd class hard wood, factory made, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed.

M & L For 35 mm thick factory made 2nd class HW rail and style Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5 sq.m but not exc. 4 sq.m each complete all as specified and directed.

Taking down old shutters of any description exc. 1 sqm but not exc. 2 sqm each complete all as specified and directed.

Resecuring or easing & adusting without taking down of shutters exc 1.0 Sqm and n.exc 2.0sqm and adjusting with out taking down complete all as specified and directed.

Taking down steel window/ventilator including grills of any description, n. exc 1.5 Sqm each including making good disturbed surface of Jamb, soffit etc complete all as specified and directed.

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications complete all as specified and directed.

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed.

S&F, in repair, aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed.

S&F, in repair, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 250 mm and fixed complete all as specified and directed.

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 250 mm and fixed complete all as specified and directed.

S&F, butt hinges, medium weight, cold rolled, mild steel of size 75mm complete all as specified and directed.

S&F, butt hinges, medium weight, cold rolled, mild steel of size 100mm complete all as specified and directed.

S&F, in repair, butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified and directed.

S&F, single action spring hinges (ISI MarK), mild steel with steel wire spring, stove enameled black, size of spring hinge 125mm all as specified and directed.

S&F, in repair, single action spring hinges (ISI MarK), mild steel with steel wire spring, stove enameled black, size of spring hinge 125mm all as specified and directed.

S&F, brass handles, cast type of size 100mm suitable for cupboard etc complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

S&F, 100 mm aluminium anodised hasp and staple complete all as specified and directed.

S&F in repairs, brass chromium plated, tubular towel rail 20mm dia, D type, 60 cm long between flange, complete all as specified and directed.

S&F 140mm overall length floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor complete all as specified and directed.

S&F in repair 140mm overall length floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F, stainless steel butt hinges, medium weight, of size 100 mm complete all as specified and directed.

S&F framed work such as grills, grating etc with ends of bars shoulderd or rivetted or forcged into spikes ,framed guard bars, barred iron doors congirming to FE 290 Gde E-165 complete all as specified.

S&F, Mild Steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking , bending, hooking etc and binding with MS wire 0.9mm dia(annealed).

M&L Rolled mild steel sections conforming to Gde Fe-410-0 or Fe-310-0 as in framing for cladding, glazing and the like including door frames/ chowkats, coolerstand etc fixed with angle cleats and connecting plates, etc complete all specified and directed.

S&F mild steel work in weather shed posts, main and cross beams, hip and jack rafters, purlins, including special shaped washer etc. complete using ERW or induction butt welded tubes, conforming to IS 1161-1979, Gde St-240 complete all as specified and directed.

S&F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

M&L for cutting uneven surfaces of concrete & cutting reinforcement from drops of fins & facias (thickness not exceeding 50mm) using necessary scaffolding and making good the disturbed portion with 5mm thick rendering in CM 1:3 finished even and smooth without using extra cement etc. complete all as specifeid and directed.

Removing existing water proffing /black top treatment from parapet wall, removing material to a distance exc. 1.5 Km but not exc. 5.0 KM out side MD land complete all as specified and directed.

M&L for water proofing treatment to non accessible roof slabs by applying one coat of cold bituminous primer @ 0.30 litre/sqm and conforming to IS-3384, laying APP based polyster modified membrane reinforced non wooven polyster of 3.50 Kg/Sqm (minimum), 3mm thick with plain polythene finished and sealing all the overlap 75mm in length side and 100mm in width side of membrane by torching including applying one coat of bituminous aluminium paint over membrane all as specified and directed .

M & L Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour (as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed.

S&F, 18/19mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice laminations and other side balanceing white lamination, including necessary side liping fixed with screws to timber frame work in cup boards, rebated or flat edged complete all as specified and directed.

M&L for machine cut kota stone slab 18-20mm thick as in flooring laid over and including cement mortar screed bed of 15mm thick in CM (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for machine cut kota stone slab 15-16 mm thick as in riser of steps, skirting, dado and pillar laid over and including rendering 10mm thick in cement mortar (1:4), jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L 16 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms over 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as steps, cooking platform, and other similar situations complete all as specified and directed.

M&L for mirror polishing on granite/ Kota stone work where ever required to give high glosss finish complete all as specified and direted.

M&L for 75mm thick cement concrete 1:3:6 type C1, using 40mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L 75 mm thick cement concrete type D2, 1:4:8 (40mm graded aggregate) in sub-floors, sub-bases, floors and pavings etc complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in flooring finished fair and even to receive floor finishes complete all as specified and directed.

M&L for 40 mm thick (average consolidated thickness) PCC (1:2:4) type B-1 using 20 mm graded stone aggregate mixed with liquid water proofing compound as per manufacturer instruction, laid in slope 1:30 on roof as in padding, finished even and fair complete all as specified and directed.

M&L for non skid coloured tiles any colour 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 Sqm and not exceeding 0.18 Sqm each in skirting etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size 350x250x7mm / 450x350x7mm thick on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match over 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L, for machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 of 60mm thickness, M-35 grade including 25mm thick (compacted thickness) sand cushion below paver blocks complete all as specified and directed.

M&L for rendering cement plaster 15mm thick 1:4 on brick work of concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick on on fair faces of concrete surfaces as on PCC padding in CM 1:3 mixed with liquid water proofing compound as per manufacturer instruction and finish the surface even and smooth without using extra cement for laying APP membrane at non-accessible roof (mumty) all as directed. (Note :- water proofing compound shall be measured and paid sepretally)

M&L for rendering cement plaster 10mm thick in cement mortar (1:6) on brick work or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar 1:3 on fair faces of concrete in ceilings, chajjas, fins facia etc. finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for water proofing of sunken portion consisting under mentioned items :- (i) 15 mm thick plastering in C:M 1:3 with liquid WPC at all around and base of sunken floor with proper slope. (ii) Applying a coat of bitminous primer @ 0.30 litre/sqm (WPC included) and conforming to IS-3384, laying APP based polyster modified membrane reinforced non wooven polyster of 3.50 Kg/Sqm (minimum), sealed by torching including demolition and removal of old concrete and provn of new lean cement concrete 1:5:10 type E 2 using 40 mm graded stone aggregate specified complete all as specified and directed

M&L Aluminium powder coated (powder coated of requried colour) three track sliding windows frame top & sides of size 92x31.75x1.30mm (section No 20621), bottom size 92x31.75x1.30mm (section No-20620) and shutter top & bottom of size 40x18x1.29 mm (section No-20844) and sides (handle) of size 40x18x1.29mm (section No-20846) and lock side shutter frame of size 40x18x1.29 mm (Section No 20845) with rubber gasket, beading and locking arrangement and rollers etc including stainless steel wire mesh 0.36mm nominal dia of wire with 1.40mm average aperture and fixed with stainless steel wire staples and fixing 4mm thick glass (any shade) with necessary rubber beading gasket etc all as specified. Make:-Indal/ Jindal/ Hindalco.

M&L Aluminium powder coated (powder coated of requried colour) two track sliding windows frame top & sides of size 68.85x31.75x1.30mm (section No 20681), bottom size 68.85x31.75x1.20mm (section No 20619) and shutter top & bottom of size 40x18x1.29 mm (section No-20844) and sides (handle) of size 40x18x1.29mm (section No-20846) and lock side shutter frame of size 40x18x1.29 mm (Section No 20845) with rubber gasket, beading and locking arrangement and rollers etc including making good to the disturbed portion complete including 4mm thick glass any shade with necessary rubber beading gasket etc all as specified. Make:-Indal/ Jindal/ Hindalco.

S&F 18mm thick, PVC sheet one side prelaminated of approved texture ("Celuca Ply of Rajshree make or equivalent in "Sintex" as approved by GE) as in Kitchen cabinet/cupboard (with shelves and partitions) including necessary fittings & fixtures like auto closing concealed hinges, 75mm long fancy type SS Handle, magnet catch etc as per manufacturer's instructions complete and taking out old board of cabinat all as specified and directed.

M&L for complete removal of existing treatment if wall/roof projections including facia, cornices etc by scraping with mechnnical sander (having mechnical vaccum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust, loose paint etc by skilled labour incl necessary acaffolding complete all as specified and directed.

M&L for two coats of Acrylic distempe over one coat of 1mm thick wall care putty ( Make : Birla/JK White) base on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for complete removal of existing treatment (any no of layer) of wall and applying two coats of Acrylic distemper over and including one coat of minimum 1mm thick wall care putty (Make : Birla/JK White) base on old treated surface including preparation of surfaces complete all as specified and directed.

M&L for preparing new plastered or un-plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for preparing old plastered or un-plastered surfaces and applying one coat of white wash on ceilings complete all as specified and directed.

Material and Labour for applying Two or more coats of 100% Premium exterior acrylic emulsion paint latex based having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm. Note- (i) contractor shall furnished guarantee of four years against service rendered) (ii) primer and emulsion to be carred out through air less spray machine (Mechanical means)

S&F 3mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq.m in each pane

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of old wooden surface of any description, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old steel surface of any description exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

M&L for writing letters or figures (block, roman, Italic or Indian) not exc. 30cm high with synthetic enamel paint complete all as specified and directed.

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 25mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 25mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 15mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 20mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 25mm bore of pipe complete all as specified and directed.

S&F 40mm bore low density polythene pipe (LDPE) of pressure rating 6 kg/sq cm fixed to walls, celling or in floors etc complete all asspecified and directed.

Supplying and laying of 20mm outer dia CPVC pipes SDR 13.5 fittings on walls/ceiling or laying in floors including connection to old GI Pipe (if requried) complete all as specified and directed.

S&F of 20 mm outer dia CPVC elbow (3/4x 1/2) with brass thread at one end for fixing of taps etc and other end plain complete all as specified

S&F of 20mm outer dia CPVC Tee with brass thread at one end for fixing of taps etc and other end plain complete all as specified

Disconnecting, setting aside (or lowering if required) and Cleaning & removing all scale and dirt etc from HDPE water tanks of 500 litres capacity (Tanks placed on top of roof) and from mouths of circulating pipes etc including washing the tank with bleaching powder and hoisting, reconnecting and re-fixing in position including writing the date of cleaning of tank with synthetic enamel (black/white) paint of size not less than 10cm of each letter complete, all as specified and directed.

Supply, hoisting and fixing in position in repairs, 500 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top) including dismantling of old PVC/AC water storage tank of 500 liter capacity complete all as specified and directed.

S&F, in repairs, 15mm brass chromium plated fancy type bib cock with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed.

Supply only pillar taps fancy type cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed 15 mm bore dia complete all as specified and directed.

S&F, in repairs, 15mm stop valves, fancy type brass chromium plated for iron pipe or for unions and fixed to 15mm bore pipe, complete all as specified and directed.

S&F, in repairs chromium plated with long shank and cup (concealed type) 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as directed.

S&F, in repair, Gun metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe for 20 mm bore of pipe complete all as specified and directed.

S&F, in repair, Gun metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe for 25 mm bore of pipe complete all as specified and directed.

Supply only, 32mm, waste fittings, brass chromium plated for glazed ware sink, basins, etc. with long screw shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight -210 Gms) complete, all as specified and directed.

S&F in repair 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight -210 Gms) complete, all as specified and directed.

Supply only PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F, 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including stack 'Z' clamp complete all as specified and directed.

S&F, 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including 'Z' clamp complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bend, any radius complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radiuscomplete all as specified and directed.

S&F 75mm bore PVC (SWR) Tee equal or unequal any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) Tee equal or unequal any radius complete all as specified and directed.

S&F, 110mm PVC (SWR) vent cowl complete all as specified and directed.

S&F PVC (SWR) nahani trap, with chromium plated grating including jointing with solvent cement, dia of outlet 75mm complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, fixed complete all as specified and directed.

S&F in repair vitreous China squatting pan 'Orissa pattern' size 580x440 mm, white with integral foot rest including 'P' or 'S' trap front or back inlet excluding flushing cistern and flush pipe including connection to trap and flushing pipe etc and making good to floor complete all as specified and directed.

S&F, in repair, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S&F, in repair, vitreous china wash basin, white, flat back of size 450mm x300mm including brackets grouted in cement mortar 1:2 in wall complete all as specified and directed. Note :- Supply only pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately.

S&F, in repair, brass chromium plated shower rose with or without swivel joint, 125mm size complete all as specified and directed.

S&F, in repair, corner glass shelf with CP brackets and with decorative railing fixed to wall complete all as specified and directed.

S&F, in repair, 25mm dia, 1mm wall thickness stainless steel fancy type heavy duty curtain rod with decorative ball type side brackets (as per sample) fix with wooden gutties complete all as specified and directed.

Supply only PVC waste pipe 32mm bore of size 450mm to 600mm long complete all as specified and directed.

S&F, in repair, 0.63 mm thick, heavy duty stainless steel plate rack of size 24x30x10 inch complete all as specified and directed.

S&F, in repair kitchen sink without drainage board made of stainless steel 1mm thick including supply and fix 32mm CP waste coupling, plug, washer, 32 mm bore and 60cm long PVC waste pipe including cantilever brackets made of mild steel angle iron 30x30x4mm and flat iron 25x3mm both duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, cutting for and pinning in ends of brackets to errecting stand into wall and making good disturbed portion in cement mortar 1:2 or in PCC 1:2:4, type B-1 using 20mm graded stone aggregate and connecting union to pipe, over all size 45mmx420mm bowl size 410mmx330mmx160mm complete all as specified and directed.

S & F in repair Soap dish, stainless steel, standard size Soap dish, any type, fixed to plugs with chromium plated brass screws complete.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

Demolition of stone slabs and stone tiles laid dry andpointed complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc. 15cm thickness (below or above ground level) all as specified and directed.

Demolition of reinforced cement concrete as in manhole covers, etc complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed

Dismantling of cast iron, PVC or reinforced concrete drain pipes jointed in cement mortar for 110mm and 75mm bore of pipe from wall/floors etc complete all as specified and directed.

Taking down carefully copper/Aluminium point wiring (Light, fan, socket or power) complete including fitting such as switches, socket, bell pushes, ceiling roses, pendants/batten holder, call bell, regulators etc all as specified and directed by Engr-in-charge.

M&L for wiring with and including multi stranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with valid CML number, drawing through in and including, rigid non metallic, PVC concealed conduit of 20mm bore and including cutting chases for conduits and sinkings for boxes, its accessories & including with multi stranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with valid CML number as continuity earth wire terminating with provision sunken concealed terminal boxes complete all as specified and directed for the followings :-

(a) One light/fan /Exhaust point controlled by one switch

(b) One multi purpose socket 5 Amps, on the same board.

(c) One multi purpose socket 5 Amps, Independent board.

(d) One bell buzzer point controlled by one push buttons independent board.

(e) One light point controlled by two way switch.

M&L for wiring with and including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including medium grade PVC concealed conduit of 20mm bore fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box complete all as specified and directed.

S&F, in repairs, LED light fitting, 1 x 20 watt 220V, AC, decorative box type with driver , holder , including LED tube light complete set flexible three core copper conductor cable of suitable size and testing on completion all as specified and directed.

S&F, lamp holder insulated body with back plate for battern fittings complete all as specified and directed.

S&F Switch piano, flush type 5 Amps One Way 230 volts complete all as specified.

S&F, in repair, Switch piano one way 15 Amps flush type 230 volts complete all as specified.

S&F, in repair, Switch piano two way 5 Amps flush type 230 volts complete all as specified.

M&L, in repair, bell push, flush type single pole, 5 Amps complete all as specified and directed.

S&F Socket outlet 2-in-1 3 pin 6 & 16 Amps flush type 230 volts complete all as specified.

S&F, in repair, socket outlet 2 in1, 3 pin, 5 Amps, flush type complete all as specified and directed.

S&F Sheet metal enclosure single door for DB's SPN 8 way 240 V having 200 A rated bus bar complete all as specified and directed by Engr-Incharge.

S&F Ceiling rose 3 terminal size 50x65mm surface type 230 volts complete all as specified.

S&F, in repair, LED light decorative ultra slim round profile LED lightning with extured polycarbonate environmental friendly energy efficient ready to use pack 2 feet 9 watt 220 V AC including connecting up with three core flexible copper conductor cable of suitable size complete all as sepcified and directed.

Supply and fix LED light fitting 1 x 10 W bulk head luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size

Taking down existing exhaust geyser and keeping safe custody and re-installation the same after completion of work completed all as specified and directed.

Taking down existing Electric meter and keeping safe custody and re-installation the same after completion of work completed all as specified and directed.

Taking down existing exhaust fan and keeping in safe custody and re-installation the same after completion of work complete all as specified and directed.

M&L for ceiling rose, PVC/poly carbonate, isolated body three terminals complete all as sepcified and directed.

S&F MCB SP 6-32A, 240 V -10 KA all as specified and as directed by Engineer-in-charge.

S&F, in repair, MCB’s SPN 40 Amps 240 volts with ‘C’ curve, fixed in sheet metal board complete including connecting.

M&L in replacement sub-main wiring with 2 single core 4 Sqmm PVC insulated, unsheathed, 1100Volts grade, copper multi stranded conductor drawn in and including PVC concealed conduit and conduit assessories including drawing a run of PVC insulated, unsheathed, 650/1100Volts grade, copper conductor multi stranded 4 Sqmm size as continuous earth wire drawn through and connected to main switch/ DB and testing on completion. Note: (i). 2 run of main conductor and one run of earth conductor shall be measured as one length. (ii) Rates quoted shall be inclusive of cutting wall for concealing conduit and making good the same in cement mortar 1:3.

SNEH TRADERS

Shree Builders

ALBA AC AND REF SERVICES

TECH SERVE SOLUTIONS