PROVISION OF WEATHER PROOF EXTERIOR PAINT AFTER REMOVING EXISTING TREATMENT ON EXTERNAL SURFACES OF MES COVER BLDGS (PHASE-I), PROVISION OF ROLLER TYPE VENETIAN BLINDS TO CERTAIN ROOMS OF A BLOCK AT DESIDOC, CONSTRUCTION OF SINGLE STORY QRT GUARD LIV

Amount

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Removing excavated soil to a distance exc 3 Km but not exc 5.00 Km out side MoD land in low lying area and depositing complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, in trenches including spreading leveling, watering and well ramming in layers n.exc 25cm thick in soft/loose soil complete all as specified and as directed.

Removing excavated material to a distance n.exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed.

M&L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed. Make-CHLOROPYRIPHOS 20 EC or LINDANE 20 EC

M&L for treating the backfill in contact with foundation at the rate of 7.5 liters of emulsion per square metre of vertical surface (Area of the substructure in contact with back fill to be measured) complete all as specified and as directed. Make-CHLOROPYRIPHOS 20 EC or LINDANE 20 EC

Filling in, of excavated earth as in plinth/in floor including spreading leveling, watering and well ramming in layers n.exc 25cm in soft/loose soil complete all as specified and as directed.

M&L PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed..

M&L RCC M-25 design mix (using 20 mm graded crushed stone aggregates) as in Foundations, including rafts, footings, Foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed. Note: Reinforcement shall be measured and paid separately.

M&L RCC M-25 design mix (using 20 mm graded crushed stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and as directed. Note: Reinforcement shall be measured and paid separately.

M&L RCC M-25 design mix (using 20 mm graded crushed stone aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed. Note: Reinforment shall be measured and paid separately.

M&L RCC M-25 design mix (using 20 mm graded crushed stone aggregates) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. Note: Reinforcement shall be measured and paid separately.

M&L RCC M-25 design mix (using 20 mm graded crushed stone aggregates) as in Chajjas complete all as specified. Note: Reinforcement shall be measured and paid separately.

M&L mild steel 10 mm dia and over TMT bar cut to length, bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and as directed.

All as per item No 15.00 above but 5 mm dia and over up to 10 mm dia in stirrups, spacers and binders.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams,complete all as specified and as directed.

Form work to soffits of suspended slab such as roof slab, floor slab, landings and similar work not exceeding 20cm thick (horizontal or slopping) for fair finished surfaces complete all as specified and as directed.

Use and waste of form work to sides & soffits of plinth bands , lintel band, Shelves etc including, shelves etc. complete all as specified and as directed.

Use and waste of form work to chajjas and similar work for fair finish surfaces complete all as specified and as directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and as directed.

M&L for Brick work with sub class ‘B’ bricks, old size bricks , straight or curved on plan exceeding 6 mtr mean radius built in cement mortar (1:6) complete all as specified and as directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

M&L for 15 mm thick rendering on brick work or concrete surfaces in CM 1:4 mixed with WPC @3% by weight of cement or as per manufacturers instruction finished even and smooth without using extra cement complete all as specified and as directed. Note: WPC shall be measured and paid separately.

M&L for 15mm thick rendering in cement mortar 1:6 on brick or concrete wall surfaces of any description finished even and smooth without using extra cement complete all as specified and as directed.

M&L 5mm thick cement plaster in CM 1:3 as in soffits of slabs complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed. Make- CHLOROPYRIPHOS 20 EC or LINDANE 20 EC

M&L 18-20mm thick machine cut kota stone slab (table rubbed and polished) as in flooring laid over and including 15 mm thick screed bed or bedding layer in CM (1:6), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including, cutting, rubbing, grinding and mirror polishing complete

M&L machine cut kota stone slab 18-20mm thick as in skirting,risers of steps laid over and including 10 mm thick rendering in CM (1:6), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including cutting, rubbing, grinding and mirror polishing complete

M&L non skid ceremic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles and laid over and including 15mm thick screed bed and bedding layer of CM (1:6) complete all as specified and as directed.

M&L for Glazed coloured ceramic tiles in vertical surface as in dado of size 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick rendering in CM (1:4) complete all as specified and as directed .

M&L for 18 to 20mm thick granite stone slab as in shelves over cooking platform,machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing and beveling half round edges of stones fixed over and laid over 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for 18 to 20mm thick granite stone slab on vertical surfaces such as skirting/dado etc set and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone and beveling half round edges of stones fixed over and incl rendering 10 mm thick CM 1:3 complete all as specified and as directed.

M&L two coat of distempeer oil emulsion over a coat of primer on plastered or un-plastered surfaces of walls over two coat of wall care putty including preparation of surfaces, complete all as specified and as directed.

All as per item No 37.00 above but on ceiling.

M&L for preparation of new external plaster surfaces and including applying two coat of Exterior acrylic paint (weather proof / dust proof) over a coat of primer complete all as specified and as directed.

M&L for Aluminum window double shutter Glazed & gauged of Galvanized mild steel wire cloth nominal dia of wire 0.56 mm and average width of aperture 1.18 mm along with aluminum grill, size of frame 150 mm x 44.5 mm x 2.00mm aluminium section with 50 micron anodizing size of shutter side & top rail 83.00x44.5x1.60mm, lock & bottom rail 83.00x44.5x2.00mm thick reflector sole sheet glass to be fixed in glazed portion and stainless steel hooks & eye to be provided as stay of shutter etc complete including necessary jointing cleats, glazing clips, rubber packing , anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stay 150 mm long (01 No for each leaf) , stainless steel hinges type B-21, 100 mm long (02 Nos for each leaf), Aluminium Handle 75mm long D type (01 No for each leaf ) and 100 mm aluminium tower bolt (2 Nos in each leaf ) complete all as specified and as directed.

M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed. Make- CHLOROPYRIPHOS 20 EC or LINDANE 20 EC

M&L PCC (1:3:6) Type C-2 (40 mm graded aggregate) as in plinth protection/path 75 mm thick laid in bays incl finishing the concrete surface even and smooth without using extra cement complete all as specified. (Note: The unit rate quoted shall be deemed to include for providing the concrete in alternate bays n exc 3 mtr long with 12 mm wide and 50 mm deep joint between the bays which shall be filled with mastic filling with hot bitumen VG-10 and 1:2 mix by volume.) complete all as specified and as directed.

M&L hard core of broken stone gauge not exceeding 63mm deposited and leveled in layer not exceeding 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M&L for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall

S&F Fancy type stainless steel curtain rod / rail with fancy type bracket of SS. Bracket to be fixed with (0.075x0.075x0.075) mm to wall with cement mortar 1:3 all as specified & directed

Supply and fix 32 mm dia 3-layer PP-R Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and as directed. Make : SMFC, SAFE, WETFLOW Note:- Cutting chases for concealing the pipes & fittings etc and making good, disturbed surface in Cement mortar 1:3 complete shall be included in the quoted rate.

All as per item No 46.00 above but 20 mm dia complete all as specified and directed.

S&F PVC (SWR) pipes 110mm single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S&F PVC (SWR) 110mm bends any radius complete all as specified and as directed.

S&F PVC P or S Trap 100/110 mm dia complete all as specified and as directed.

S&F for PVC (SWR) 75 mm bore pipe in any length with rubber ring joints fixed to walls as in vent pipe incl. PVC cowl complete all as specified and as directed.

S&F 15mm bore brass chromium plated fency type concealed stop cock reduced body etc complete all as specified and directed.

S&F vitreous china urinal, Half stall type, white with CP grating, union for discharge pipe, flush pipe and waste pipe, CP urinal Spreader fixed to water supply pipe etc complete all as specified and directed. Make : Hindware, Parryware, CERA

S&F grating of size 125 mm CP for out let of water etc complete all as specified and as directed.

S&F Stainless steel towel Rail of size 600 mm with lower hanger fixed to wall complete all as specified and directed. Make - Jaquar or equivalent in PARKO,GEM,Essess

S&F for WC Orissa pattern size 580 x 440 mm of vitreous china (white) fixed with all including accessories including integral footrest etc complete all as specified and directed.

S&F vitreous china wash down water closet pedstal pattern white excluding flushing cistern complete but including fixing bolts, flush pipe, PVC seat cover with aluminium hinging devices & EWC Jet chromium plated with 1.00 mtr long PVC connection pipe etc complete all as specified and directed.

S&F PVC low level flushing cistern valveless syphonic action type 10 litres capacity with inlet ball valve, float and handle including PVC flush pipe 32 mm dia with bend and a pair of mild steel angle iron brackets of suitable size including making necessary connections to water supply pipe line and WC complete all as specified and as directed.

S&F 15mm bore pillar taps fancy type, half turn CP brass with capstan heads, scewed down high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nut, screwed for iron pipes and fixed complete all as specified.

S&F bib taps 15 mm bore chromium plated, long body fancy type, half turn cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F vitreous china wash basin white flat back size 550x 400mm excluding taps but including CP waste fitting and PVC waste pipe 25mm dia 610mm long and brackets of angle size 35x35x6mm complete all as specified and directed.

S&F half turn stop valves/angle valves cast copper alloy CP concealed fancy type screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe 15mm dia complete all as specified and as directed.

S & F PVC connections 15mm dia 450 mm long with PTMT nut on both ends and washers complete all as specified and as directed.

S&F PTMT ball valve high pressure with polylethylene float ball and fly nut complete screwed for iron pipe and fixed ,20 mm bore ,fixed in repairs complete all as specified and directed.

S&F toilet paper holder Chromium Platedcomplete all as specified and directed. Make - Jaquar, GEM, PARKO or equivalent approved make.

S&F chromium plated soap dish fixed to wall with CP brass screws etc complete all as specified and directed.

S&F overhead Shower 200x200mm Square Shape Single Flow (Body & Face Plate Brass with Chrome Plated with grey face plate) with Rubit Cleaning System suitable for 15mm bore GI pipe complete all as specified and directed. Make: Jaguar, GEM, PARKO or equivalent approved make.

S&F rotational moulded polythene water storage tank (Cylindrical vertical with closed top) 3 layered hoisted and fixed in position of 1000 ltrs capacity fixed with and incliuding PVC tank cover nipples (Minimum weight 20mm-45gms) and necessary connections complete all as specified and directed.

S&F UPVC Floor / Nahani Trap of self cleaning design with CP jalie complete in all respects of size (110x 90mm) complete all as specified and as directed.

S&F UPVC Gully traps of self cleaning design with CP jalie complete in all respects of size (160x 110mm) Single / double size as per site complete all as specified and as directed.

S&F glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, guard and railing 60cm long complete all as specified and directed.

S&F 125mm to 175mm hat pegs of aluminium, solid body fixed with screws complete all as specified and as directed.

S&F 32mm dia of bore, 3-layer PP-R Polypropylene random copolymer gate valves, with wheel head, screwed both ends for PVC pipe, complete all as specified and directed.

All as per item No.74.00 above but for 20 mm.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube as specification and drawing in SSR complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

S&F Pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (20 mm graded crushed agg as in filling pressed steel frame or hold fast blocks complete all as specified and directed.

S&F 35 mm thick factory made Plain framed, panelled shutter of 2nd class HW rail and style (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35 mm thick Glazed and skeleton shutters of 2nd class hardwood open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mi-tred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.20 (a); complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 300mm, ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F butt hinges, 100mm size extruded brass, with mild steel hinge pin, bright polished and fixed, type B-21 complete all as specified and directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 250mm size aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F 150mm size aluminium handles, cast type anodised complete all as specified and directed.

M&L for preparation of new wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer all as specified.

S&F mild steel framed work such as grills, grating, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars, barred iron doors, ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as directed.

M&L for applying two coat of synthetic enamel paint one a coat of red oxide primer on new decorated steel surfaces exc 10 cm width or girth including preparation of surfaces, complete all as specified and directed.

M&L Water proofing treatmentover roof at any height consisting evenly applied primer coat @ 0.30 litre/ Sq. m on surfaces, overlaps, joints etc and a layer of APP polymer 3 mm thick even membrane weight not less than 3.00 Kg/ Sq.m duly sealed at over laps joints with flame (complete by torch application) all as per manufacturer's instructions, over and including 15 mm thick screed bed of cement mortar (1:4) mixed with water proofing compound @ 2% by weight of cement, complete all as specified and directed by Engineer-in-Charge. Make: Polymod AP of M/S Chokesy chemicals/ Hyperplas Polyester of M/S IWL Ltd / Super Thermolay of M/S STP Ltd . Note:- (i) Water proofing compound shall be measured and paid separately. (ii) Application of polymeric membrane shall be by torch application. (iii) The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (iv) Primer shall be applied after preparing & cleaning of fully dried cement plastered surface. (v) Applying a coat of solar reflective bituminous aluminium paint @ 0.15 Kg per Sqm over the membrane complete.

M&L for Plain cement concrete (1:2:4) type B-0, (using 12.5 mm graded mechanically crushed stone aggregates) as in roof kerbs, benching and the like, etc complete all as specified and directed.

M&L 75mm th PCC 1:3:6 type C-2 (using 40 mm graded machire stone aggregate) as in sub base, Floors, Paving, plinth protection, finished even and fair complete all as specified.

M&L for rolling and consolidating formation surfaces in cutting exc 8 tonne & nexc 12 tonne power roller complete all as specified and directed.

M&L 25mm th PCC 1:2:4 type B-1 using 20mm graded aggregate as in flooring, finished fair and even complete all as specified and directed.

M&L sand filling under floor or in foundations including watering and consolidation complete all as specified and directed.

M&L for 80 mm thick rubber moulded polished double glossy designer interlocking tiles madeof M-40 design mix concrete of approved design and shape with a crushing strength not less than 250 Kg/sqcm complete all as specified and directed

M&L PCC 1:2:4 type B-1 as in bounding of edges of interlocking tiles and the like including watering & lightly rounded or chamfered angles and throating as directed

M&L for coping type C 1 (1:3:6) using 20mm graded stone aggregate including water troughs and the like including weathring slightly rounded or chamfered angles and throating, as directed.

M&L for precast manhole cover type B-1 (1:2:4) using 20mm graded stone aggregate including water troughs and the like including formwork weathring slightly rounded or chamfered angles and throating, as directed. Note: Reinforcement shall be measured and paid separately).

Supply and lay pipe galvanized, "Medium Class" including fittings 25 mm (1") dia bore.

M&L for mild steel deformed /twisted steel bar 8mm dia and above cut to length, bent to shape required including cranking, bending or spirally hooping etc and with and including binding with MS wire annealed of dia not less than 0.9mm complete all as specified and directed.

M&L for mild steel rungs, handle complete all as directed.

M&L for plain Cement Concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore SGSW pipe.

S&F stop valves of 25 mm dia cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both end for iron pipe or for union and fixed complete all as specified and directed.

M&L Salt glazed stoneware drain pipes 150 mm bore laid in trenches and jointed complete all as specified and directed.

Supply and laying dry fine sand for cushioning of underground cable laid in trenches/duct complete all as specified and directed.

M&L Cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 150 mm bore drain pipe.

M&L plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified.

M&L Plain cement concrete 1:2:4 Type B1 (using 20 mm graded stone aggregate) as in copings, kneelers, apex stones, bed plates, kerbs, water troughs,and the like including weathering, slightly rounded or chamfered angles and throating incl use of formwork (straight or curved) as directed.

M&L cement concrete 1:3:6 (Type - C-2 40mm graded agg) in surface channel & drain all as specified and directed.

M&L extra for forming fair finished drains or channels 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

Taking down cement plaster from brick or stone wall or concrete surfaces etc including racking out joint, hacking for key scrubing down with water complete all as specified and directed.

Material and labour for Rough cast plaster including 15mm thick rendering in CM (1:6) on brick work or concrete surfaces complete as specifed in SSR pat -I clause 14.22 complete all as specified and directed. Note :- Rough cast finish to be as below :- After applying the under coat of cement mortar (1:3) and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (which is generallly of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of (1:1:1) shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered.

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand: 2 stone chipping 10mm nominal size) in panels with and including groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified (Payment for providing grooves shall be made separately) Note: 1. Rate also includes necessary scaffolding to carry out stone grit plaster work upto a height G+6 floor.

Complete removal of existing treatment from internal / external plastered or unplastered surfaces of walls complete all as specified and directed. Note: 1. Firstly the complete removal of exisiting tratement, cleaing the surface with emery paper 180 at a height G+6 floor to remove loose cracked or flanked paint, paint dust dirt grease, wipe clean. 2. Preparation of old decorated surfaces shall include brooming down or steel wire brushing scrabing down smoke soot, moulds, moss and efforescent salts and trading oil and greasy spots

M&L for applying two coat of wall care putty on wall including preparation of surfaces by emery papar 800 and wipe clean complete all as specified and directed.

Material and labour for applying two coats of acrylic exterior emulision weather and dust proof of any tint including one coat of priming with alkali resistant primary paint ) on external cement plastered surfaces complete all specified and directed. Make : Apex ultima of Asian Brand or equivalent in Berger, Jhonson etc Note:for item No 114.00 to 119.00 1. Rate also includes necessary scaffolding to carry out work upto a height G+6 floor. 2. Rate also includes necessary cleaing of dots of painting on floor, door & window and special care shall be taken when removing any dots of paint from glass and joinery, etc. to avoid damaging their surface.

M&L for chipping of spalled and loose concrete and cleaning rust from reinforcement by sand blasting scrubbing down concrete surface with wire brushes cleaning with water allowed to dry and applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bounding coat of approved epoxy adhesive on complete exposed surfaces of concrete to be gunited all as specified and applying two layers of guniting over steel welded mesh 2mm dia of wire and aperture 75mm, total thickness of gunite n.exc 40mm thick (average thickness) in cement mortar (1:2) using OPC 53 grade cement mixed with polycrete admixture @ 2% by weight of cement or as per manufacturer instructions and finally applying cement plaster over gunite surface of required thickness to give even uniform and smooth finish conforming to proper geometrics in cement mortar (1:3) to match the existing surface as in sides and soffits etc of slabs, chajjas, fins, facias,parapets, lintels, columns and beams etc complete including necessary scaffolding, shuttering, necessary chases to brick work or RCC members at any height upto 6 storey building including removing of small trees shrubs etc all as specified and as directed.

M&L for complete removal of existing treatment and applying two coat of synthetic enamel paint over old painted steel surfaces of any descripition over 10cm width or girth over one coat of red oxide primer complete all as specified and as directed.

M&L for removal of exsiting treatment and applying two coat of synthetic enamel paint on old decorated wooden surfaces exc 10 cm width or girth over a coat of pink primer, complete all as specified and directed.

M&L for clearing away all grass,vegetation, saplings, shrubs, brushwood, undergrowth, digging out roots, filling holes and levelling ground, stacking of serviceable material and trees not exceeding 30 cm girth and removing rubbish outside the MoD periphery of the area under clearance complete all as specified and directed. Notes :- (a) The cleaning of vegitable/brushed growing to be cleaned upto 6 (Six) storey and making good with PCC 1:2:4 type B1 with injecting of chemical and finishing the surface to match the exisitng surface complete all as spceified and directed. (b) Rate also includes necessary scaffolding, tools & plants to carry out the job upto a height G+6 floor.

S&F manually opening and closing roller type blinds of approved make with characteristic composition 100% polyster (translucent), weight 230 gm/Sqm complete all as per manufactuer instruction all as specified and as directed. Make:- VISTA or Equivalent.

S&F Vertical Veniation blind consisting of aluminium head rail, vanes/louvers 4” wide of approved tint and traverse cord complete all as per manufactuer instruction fixed in position complete all as specified and directed. Make: VISTA or Equivalent.

S&F double rolling vertical veniation blind consisting of alum head rail, with flip cover of approved tint and traverse cord complete all as per manufactuer instruction fixed in position complete all as specified and directed. Make: VISTA or Equivalent.

Cutting openings, through brick walls for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m

S&F Floor door stopper of aluminium alloy body and tonge anodised with hard drawn steel spring with overall length of cover plate 150mm all as specified.

S&F 50 micron thick powder coated alum section swing door shutters partly panelled and partly glazed comprising top rail 85.00mmX44.45mmX2.70mm (Jindal Alum section No 19563), bottom rail 150mmX44.45mmX2.20mm (Jindal Alum section No 19517), lock rail 150X44.45mmX3.00mm (Jindal Alum section No 19596) and styles 47.62mmX44.45mmX1.62mm (Jindal Alum section No 19526) And including jointing cleats,alum snap beading (Jindal Alum section 19360), rubber gasket glazing clips and two Nos disc type handles and one nos alum tower bolt 200mm long for each leaf on one side and 01 no 6 lever dead lock of brass for each leaf fixed in position complete all as spd and as directed.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty complete all as specified and directed.

S&F 50micron thick powder coated aluminium section partly glazed / partly panelled partitions and fixed glazing frame made out of alum frmae of section 63.50mmX38.10mmX1.60mm thick incl necessary jointing cleats, glazing clips, rubber packing anodised alum snap beading screws etc frame work fixed to walls, floors and ceiling with rawl plug wherever required complete for each leaf complete all as specified and as directed.

M&L 12 mm thick Prelaminated particle board, interior grade, prelaminated on both side with decorative choice laminations, fixed to aluminium frame work anodised aluminium beading complete all as specified and directed.

S&F 4.8 mm thick Sheet glass, ordinary quality of any colour, fixed with aluminium glazing clips, rubber beading / gaskets in area exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 100 mm long brass Mortice lock, 4 lever, vertical type, size 100 mm complete all as specified and directed.

Supply and fixing in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs Grating round 140 mm size of PTMT (Minimum weight 50gms) complete all as specified and directed.

S&F in repair 15mm bib tap cast copper alloy crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed but fancy type and chromium plated all as specified and directed.

M&L for 25mm thick PCC 1:2:4, type B-1, using 20mm graded stone aggregate, with spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified and directed.

M&L for 50 mm thick cement concrete type D-2 1:4:8 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed. Note: Glass shall be measured and paid separately.

M&L for RCC (Nominal Mix) type 1:2:4 (20mm aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.

S&F 50 micron thick powder coated coloured anodised aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified and as directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or with tinned tacks to aluminium frame work complete all as specified and as directed.

S&F in repair PVC water tanks of capacity 500 litre HDPE triple layered , cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 20 mm - 210 gms etc complete all as specified and directed. Note :GI inlet, outlet & wash out pipe will be measured paid for separately.

S&F nipple suitable for HDPE water tank. (Minimum weight 15 mm 38gms/20mm- 45gms /25mm- 65gms) complete all as specified and directed.

S&F 20mm bore dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 15mm bore tube medium grade galvanized with all fitting and fixed complete to walls and ceilling or laid in floors of any length complete all as specified and directed.

M&L for sub class 'B' burnt birkc flate across the cable, for protection of cable laid in trenches complete all as specified and directed.

Supply and fixing in repair Grating doom 125 mm dia with waste hole of PTMT (minimum weight 40gms) etc complete all as specified and directed.

Supply laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armourred, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.00 Sqmm 2 core complete all as specified and directed.

M&L for point wiring of any length as per site requirment with PVC insulated FRLS unsheathed copper conductor cable of size 1.5 sqmm including earth wire of size 1.5 Sqmm in and including rigid PVC concealed conduit of suitable size excluding MS sheet box and modular top sheet top cover, One light point or one fan point controlled by one 5 Amps switch complete all as specified and directed.

All as per ser item No. 151.00 above but one 3 pin socket out let 5 Amps board independent.

All as per ser item No. 151.00 above but one 3 pin socket out let 5 Amps on same board.

M&L for three pin socket outlet 15 Amp independent point wiring controlled by one switch , of any length as per site requirment with PVC FRLS insulated unsheathed copper conductor cable of size 4.0 sqmm including earth wire of size 4.0 Sqmm in and including rigid PVC concealed conduit complete with removable internal /external angle , junctions etc complete excluding MS sheet box and modular top sheet cover, for socket out let 15 Amp complete all as specified and directed.

S&F modular switch single pole one way 6 Amps 1 module complete all as specified and directed

S&F modular switch single pole one way 16 Amps 1 module complete all as specified and directed

S&F modular socket 6 amp-2/3 pin combined 2 module complete all as specified and directed.

S&F of modular socket 6 A/16 amp -2/3 pin combined 2 module complete all as specified and directed.

S&F SPN DB 8 ways with 200 amps rated busbar 230 volt double door complete all as specified and directed.

S&F SPN DB 4 ways with 200 amps rated busbar 230 volt double door complete all as specified and directed.

S&F MCB SP, C-curve, 230 Volts 6-32 Amps 10 KA complete all as specified and directed.

S&F MCB SPN, C-curve, 230 Volts 6-32 Amps 10 KA complete all as specified and directed.

S&F metal flush box 8 module complete all as specified and directed.

S&F metal flush box 3 module complete all as specified and directed.

S&F metal flush box 6 module complete all as specified and directed.

S&F white cover plate with frame (inner plate) 3 module complete all as specified and directed.

S&F white cover plate with frame (inner plate) 8 module complete all as specified and directed.

S&F white cover plate with frame (inner plate) 6 module complete all as specified and directed.

S&F ceiling rose, 3 Phase/PVC/Polycarbonate, isolated body complete all as specified and directed.

S&F LED trica batten 230 volt, 50 Hz, 20 watt including 20 W tube and cable for connecting to ceiling rose complete all as specified and directed. Make C&S Cat part No-LT4F20WLEDT8/WD or equivalent in havells/phillips.

S&F linear & compact LED mirror light 10 watt, 6000K incluing cable for making circuit and 10 watt LED tube complete all as specified and directed. Make- Cat Part No.-LTDC01210WLED/WD of C&S or in havells/phillips.

S&F of ceiling fan 1200 mm sweep, metal body type star rated single phase 240 volts AC, including making all electric connections & flexible 3 core copper cable complete all as specified and directed. Make- Havells Cat No. ES-50 Preminum or equivalent make of ORIENT/CROMPTON.

S&F of exhaust fan 250 mm sweep including louver, non metal body type single phase 240 volts AC, including making all electric connections & flexible 3 core copper cable complete all as specified and directed. Make- Havells Cat No.Ventil Air - DX White or equivalent make of ORIENT/CROMPTON.

S&F hot water appliances of capacity 25 Ltrs complete with PVC (heavy duty) pipe connection and control star rated complete all as specified and directed. Make- Havells/bajaj/crompton

M&L for earthing complete with galvanised steel earth plate electrode 60x60cmx6.0mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level ) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanised earthwire 4mm dia by means of nuts bolts, check nut and washers of galvanised iron protected by 15 mm bore GI pipe (medium grade) and connected to main switch board as directed including concrete pit in PCC (1:3:6) type C1 precast RCC (1:2:4) type B1 cover slab 40x40 Cm x 40mm reinforced with 8 mm dia deformed bar @ 5 cm c/c with one handle for lifting made out of 8 mm dia MS bar, funnle, wire mesh, 20 mm bore GI pipe (medium grade) for watering including charcoal and salt in alternative layers necessary excavation and earth work in any type of soil and testing complete all as shown on electrical plate No-3 of SSR Part-I.

S&F street light with LED Street light fitting with aluminum PDC housing and toughened glass cover with IP 66 Protection 45watt including all accessories and wiring including suitable GI braket made with GI Pipe light grade 40mm dia not less than 1.5 mtr length, in 135 degree angle including weldeing, nut bolts & clamps complete complete all as specified and directed. Make : C&S Cat No. LTESSI45WLED or equivalent in Bajaj/ Philips/ Havells

M&L of Wiring for circuit/submain wiring alongwith earth wire of FRLS PVC insulated copper conductor,single core cable in surface/recessed of size 2X6 sq mm + 1X4.0 Sqmm earth wire including suitable size of PVC conduit and lugs/thimble with nuts,bollts and washers etc complete all as specified and directed.

DP COMPLEX

V.V CONSTRUCTIONS