Fabrication and erection of new shutters at Thalachira in Cherikkonam in Mukhathala Block Panchayath, Kollam

Amount

Fabrication, painting and erection of new shutter and hoisting mechnanism of well no:1 in Thalachira

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

od21099/2020_2021/MH : Providing temporary platform for dismantling concrete and fixing embedded parts in the wellincluding cost of all materials, labours etc. complete

od21375/2020_2021/MH : Demolishing old cement concrete in the well for fixing embedded parts manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.

5.8 : Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with 1:11/2:3 (1 cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

od1430/2020_2021/MH : Fabrication and errection of Embedded parts for canal shutters ( up to 2 tonne weight ) and accessories asper approved specifications, drawings and directions of deptl officer at site including cost of labour,machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of materialalready supplied

od1431/2020_2021/MH : :Fabrication, Supply, erection and assembling of wheel track, sill seat and seal trackin correct position and alignment by welding SS Embedded parts in 304L Grade as per approvedspecifications, drawings and directions of deptl officer at site including cost of all materials, labour,welding,shearing, grinding etc,lead and lift, conveyance, incidental and handling etc complete

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

od62821/2019_2020/MH : :Supply of MS Bolts and Nuts

od62822/2019_2020/MH : Supply of Bolts and nuts above 300 mm in length

od64019/2019_2020/MH : Supply of 32 mm GIpipe

od1432/2020_2021/MH : Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight ) /Hoisting Bridge /Platform and accessories etc. for the same as per approved specifications, drawings and directions ofdeptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handlingcharges etc complete but excluding cost of material already supplied

85.118 : Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings

85.116 : Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od1433/2020_2021/MH : Providing of worm and pinion having a lifting speed of around 5.00 cm/min for hand operation including costof all materials, labor, hire charges and conveyance

od1434/2020_2021/MH : Providing EN 8 screw rod 7.50 tonn capacity 4.00M lift screw hoist having one number of EN 8 screw shaft having a lifting speed of around 5cm/ min for 24 rpm of hand operation including cost of all materials, hire charges and conveyance

od21388/2020_2021/MH : Machining of shaft 67mm outer dia , Including cost of all material, labour,tools etc. complete

od63252/2019_2020/MH : Fixing of Screwed flange coupling including cost of labour, hirecharges etc

od21381/2020_2021/MH : Fabrication of screwed MS flanges for connecting rod(65mm NB) including cost of material, labour , machinery, conveyance, painting, incidental and handling charges etccomplete.

85.115 : Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od64050/2019_2020/MH : Supplying and fixing of plummer block to support interconnecting MS Rod including cost of labour , hirecharges, materials etc

od1435/2020_2021/MH : Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Bridge / Platformincluding hand rails , lader etc. for the same including . alignment correcting and settingcomplete including cost of all labour, machinery, incidental and conveyance , lead and liftcharges etc complete but excluding cost of materials already supplied

od1474/2020_2021/MH : Conveying manually the fabricated shutter and its accessories from road side to site

od1475/2020_2021/MH : Trial run the gates with its hoisting mechanism etc. including cost of all materials,machinery , labour, all lift and lead, incidental and conveyance charges etc. As per instruction ofdepartmental officers in charge.

Fabrication, painting and erection of new shutter and hoisting mechanism of well no:2 in Thalachira

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

od21375/2020_2021/MH : Demolishing old cement concrete in the well for fixing embedded parts manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.

od21099/2020_2021/MH : Providing temporary platform for dismantling concrete and fixing embedded parts in the wellincluding cost of all materials, labours etc. complete

5.8 : Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with 1:11/2:3 (1 cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

od1431/2020_2021/MH : :Fabrication, Supply, erection and assembling of wheel track, sill seat and seal trackin correct position and alignment by welding SS Embedded parts in 304L Grade as per approvedspecifications, drawings and directions of deptl officer at site including cost of all materials, labour,welding,shearing, grinding etc,lead and lift, conveyance, incidental and handling etc complete

od1430/2020_2021/MH : Fabrication and errection of Embedded parts for canal shutters ( up to 2 tonne weight ) and accessories asper approved specifications, drawings and directions of deptl officer at site including cost of labour,machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of materialalready supplied

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

od62821/2019_2020/MH : :Supply of MS Bolts and Nuts

od62822/2019_2020/MH : Supply of Bolts and nuts above 300 mm in length

od64019/2019_2020/MH : Supply of 32 mm GIpipe

od1432/2020_2021/MH : Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight ) /Hoisting Bridge /Platform and accessories etc. for the same as per approved specifications, drawings and directions ofdeptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handlingcharges etc complete but excluding cost of material already supplied

85.118 : Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings

85.116 : Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od1434/2020_2021/MH : Providing EN 8 screw rod 7.50 tonn capacity 4.00M lift screw hoist having one number of EN 8 screw shaft having a lifting speed of around 5cm/ min for 24 rpm of hand operation including cost of all materials, hire charges and conveyance

od21388/2020_2021/MH : Machining of shaft 67mm outer dia , Including cost of all material, labour,tools etc. complete

od1433/2020_2021/MH : Providing of worm and pinion having a lifting speed of around 5.00 cm/min for hand operation including costof all materials, labor, hire charges and conveyance

od64103/2019_2020/MH : Fixing of Screwed flange coupling including cost of labour,hirecharges etc in well no. 2

od21381/2020_2021/MH : Fabrication of screwed MS flanges for connecting rod(65mm NB) including cost of material, labour , machinery, conveyance, painting, incidental and handling charges etccomplete.

85.115 : Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od64050/2019_2020/MH : Supplying and fixing of plummer block to support interconnecting MS Rod including cost of labour , hirecharges, materials etc

od1435/2020_2021/MH : Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Bridge / Platformincluding hand rails , lader etc. for the same including . alignment correcting and settingcomplete including cost of all labour, machinery, incidental and conveyance , lead and liftcharges etc complete but excluding cost of materials already supplied

od64064/2019_2020/MH : Conveying manually the fabricated shutter and its accessories from road side to site

od1475/2020_2021/MH : Trial run the gates with its hoisting mechanism etc. including cost of all materials,machinery , labour, all lift and lead, incidental and conveyance charges etc. As per instruction ofdepartmental officers in charge.

Fabrication, erection and painting of shutters(3nos) and hoisting mechanism of Spillway gate

15.2.1 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

od64285/2019_2020/MH : Dismantling the existing wooden shutter , screw rod and its accessories, stacking these shutter at convenient place .Including the cost of all material ,labor,hire charges.energy charges,conveyance and all leads and lifts etc.complete.

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.8 : Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with 1:11/2:3 (1 cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

od1430/2020_2021/MH : Fabrication and errection of Embedded parts for canal shutters ( up to 2 tonne weight ) and accessories asper approved specifications, drawings and directions of deptl officer at site including cost of labour,machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of materialalready supplied

od1431/2020_2021/MH : :Fabrication, Supply, erection and assembling of wheel track, sill seat and seal trackin correct position and alignment by welding SS Embedded parts in 304L Grade as per approvedspecifications, drawings and directions of deptl officer at site including cost of all materials, labour,welding,shearing, grinding etc,lead and lift, conveyance, incidental and handling etc complete

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

od62822/2019_2020/MH : Supply of Bolts and nuts above 300 mm in length

od62821/2019_2020/MH : :Supply of MS Bolts and Nuts

od64019/2019_2020/MH : Supply of 32 mm GIpipe

od1447/2020_2021/MH : Supply of GI pipe 40 mm dia

od1432/2020_2021/MH : Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight ) /Hoisting Bridge /Platform and accessories etc. for the same as per approved specifications, drawings and directions ofdeptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handlingcharges etc complete but excluding cost of material already supplied

85.116 : Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing

85.118 : Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od1434/2020_2021/MH : Providing EN 8 screw rod 7.50 tonn capacity 4.00M lift screw hoist having one number of EN 8 screw shaft having a lifting speed of around 5cm/ min for 24 rpm of hand operation including cost of all materials, hire charges and conveyance

od1433/2020_2021/MH : Providing of worm and pinion having a lifting speed of around 5.00 cm/min for hand operation including costof all materials, labor, hire charges and conveyance

od64284/2019_2020/MH : SUPPLYING and FIXING CAST STEEL THRUST ROLLER ASSEMBLY forVERTICALLIFT GATE having 110mm Dia, 80mm tread width, SS(304) shaft with bronze Bush and accessoriesas per approved specifications and drawings including cost of all materials,machineries, labour , all lift andlead, incidental and conveyance charges etc complete.

85.115 : Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od1435/2020_2021/MH : Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Bridge / Platformincluding hand rails , lader etc. for the same including . alignment correcting and settingcomplete including cost of all labour, machinery, incidental and conveyance , lead and liftcharges etc complete but excluding cost of materials already supplied

od64132/2019_2020/MH : Conveying manually the fabricated shutter and its accessories from road side to site

od1475/2020_2021/MH : Trial run the gates with its hoisting mechanism etc. including cost of all materials,machinery , labour, all lift and lead, incidental and conveyance charges etc. As per instruction ofdepartmental officers in charge.

K.K.Sivan

Bidder Name

GANGADETHAN

K.K.Sivan