Construction of Admin Cum Academic Block in Vallabh Degree College Mandi HP Phase-1

Amount

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m (one point five metre) in width or 10 sqm (ten square metre) on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m (one point five metre), including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m (fifty metre) . Ordinary rock including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and laying damp-proof course 40mm (forty millimetre) thick with cement concrete 1:2:4 (one cement : two coarse sand: four graded stone aggregate 12.5mm (twelve point five millimetre) nominal size) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (One Cement : Four coarse sand :Eight graded stone aggregate 40 mm (forty millimetre) nominal size) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (One cement : Five fine sand : Ten graded stone aggregate 40 mm (forty millimetre) nominal size) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 (ten) of approved quality using 1.7kg (one point seven kilogram) per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Making plinth protection 50mm (fifty millimetre) thick of cement concrete 1:3:6 (One cement : Three coarse sand (zone - III) : Six graded stone aggregate 20 mm (twenty millimetre) nominal size) over 75mm (seventy five millimetre) thick bed of dry brick ballast 40 mm (forty millimetre) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm (fifteen into twenty two centimetre) in cement mortar 1:6 (One Cement : Six Sand) and inside plastring with cement plaster 1:3 (One Cement: Three Sand) including earth work and laying 10 cm (ten centimetre) cement concrete in 1:5:10 (One Cement : Five Sand : Ten graded stone aggregate) of 40 mm (forty millimetre) nominal size) and 7.5 cm (seven point five centimetre) cement concrete 1:2:4 (One Cement : Two Sand : Four Graded stone aggregate of 20 mm (twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns etc. for mass concrete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and acceess platform including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Centering and shuttering including strutting, propping etc. and removal of form for : Stairs, (excluding landings) except spiral- staircases including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Edges of slabs and breaks in floors and walls : Under 20 cm (twenty centimetre) wide

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in mouldings as in cornices, windows sills etc, including setting in cement mortar 1:3 (One cement : Three coarse sand) cost of required centering, shuttering but, excluding the cost of reinforcement, with 1:1.5:3 (One cement : One point Five coarse sand) : Three graded stone aggregate 20 mm (twenty millimetre) nominal size) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Encasing Rolled Steel Sections in beams and columns with machine batched and machine mixed design mix M-30 (Thirty) grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability including centring and shuttering complete but excluding cost of reinforcement as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and including cost of binding wire binding all complete upto all floor level. Thermo-Mechanically Treated bars of grade Fe-500D or more including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and laying in position machine batched and machine mixed design mix M-25 (twenty five) grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum.(three hundred thirty kilogram per cubic metre) Excess/ less cement used as per design mix is payable/recoverable separately). (I) All works upto plnth level including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying in position machine batched and machine mixed design mix M-25 (twenty five) grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. (three hundred thirty kilogram per cubic metre) Excess/ less cement used as per design mix is payable/recoverable separately). (I) All works above plinth level upto all floor level including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm (one point zero millimetre) thick as per design for expansion joints.: 200 mm (two hundred millimetre) wide including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall confirm to ASTM 6063). Floor Joint of 100 mm (one hundred millimetre) gap including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063). : Wall Joint of 100 mm (one hundred millimetre) gap including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221- 02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063.) Roof Joint of 100mm (one hundred millimetre) gap including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level up to floor any level in all shapes and sizes in : Cement mortar 1:6 (One cement : Six coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level up to floor any level. Cement mortar 1:4 (One cement :Four coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and laying autoclaved aerated cement blocks masonry with 150mm (one hundred fifty millimetre)/230mm (two hundred thirty millimetre)/300 mm (three hundred millimetre) thick AAC blocks in super structure above plinth level up to floor any level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement :Six sand : Twelve graded stone aggregate 20mm (twenty millimetre) nominal size) at plinth level in including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Coursed rubble masonry (second sort) with hard stone in foundation & plinth with : Cement mortar 1:6 (One cement : Six coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Boulder filling under floors tightly hand packed including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing 18 mm (eighteen millimetre) thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm (twenty millimetre) thick base cement mortar 1:4 (One cement : Four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade : Area of slab over 0.50 sqm (zero point five square metre) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing edge moulding to 18 mm (eighteen millimetre) thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing ISI marked decorative flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 (three) ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm (thirty five millimetre) thick including ISI marked Stainless sqm Steel butt hinges with necessary screws including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Extra for providing lipping with 2nd class teak wood battens 25 mm (twenty five millimetre) minimum depth on all edges of flush door shutters (over all area of door shutter to be measured) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Extra for providing vision panel not exceeding 0.1 sqm (zero point one square metre) in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or square including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing 18 mm (eighteen millimetre) thick, 150 mm (one hundred fifty millimetre) wide pelmet of coir veneer board ISI marked IS : 14842, including top cover of 6 mm (six millimetre)coir veneer board, nickle plated M.S. Pipe 20 mm (twenty millimetre) dia. (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm (twenty five into three millimetre) M.S. Flat 10 cm (ten centimetre) long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm (one hundred millimetre into forty millimetre into forty millimetre) on both inner side of pelmet and rawl plugs 75 mm (seventy five millimetre) long etc. all complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing 40x5 mm (forty into five millimetre) flat iron hold fast 40 cm (forty centimetre) long including fixing to frame with 10 mm (ten millimetre) diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm (thirty into ten into fifteen centimetre) 1:3:6 mix (One cement : Three coarse sand : Six graded stone aggregate 20mm (twenty millimetre) nominal size) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing oxidised M.S. double acting spring hinges with necessary screws etc. complete. 150mm (one hundred fifty millimetre) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing Cromium plated brass 100 mm (one hundred millimetre) mortice latch and lock with 6 (six) levers and a pair of lever handles of approved quality with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm (one point sixty ± zero point two millimetre) thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm (one hundred into eight millimetre) size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single/double Toughten glass panes 6mm (six millimetre) thick and silicon sealant shall be paid separately) Casement window double panels with S.S. friction hinges 350 x 19 x 1.9 mm (three hundred fifty into nineteen into one point nine millimetre) made of (big series)frame 67 x 60 mm (sixty seven into sixty millimetre) & sash / mullion 67 x 80 mm (sixty seven int eighty millimetre) both having wall thickness of 2.3 ± 0.2 mm (two point three ± zero point two millimetre) and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm (one point fifty square metre)) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing frame work for HPL pannelling/ partitions/ wall lining etc. made of 50x50x1.6 mm (fifty into fifty into one point six millimetre) hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm (sixty centimetre) centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm (eight millimetre) dia, 75 mm (seventy five millimetre) long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing ,supplying and fixing HPL Pannels of approved brand and manufacture on aluminium extruded tubuiar and other aluminium sections including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. ( The Aluminium frame work as for /NCL frame work IGUs shal be paid for separately) including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing fire resistant door frame of section 50 x 60 mm (fifty into sixty millimetre) on horizontal side & 35 x 60 mm (thirty five into sixty millimetre) on vertical sides having built in rebate made out of 1.6 mm (one point six millimetre) thick GI sheet ( Zinc coating not less than 120gm/ m2 (one hundred twenty gram per metre square) suitable for mounting 120 min (one hundred twenty minimum) Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m3 (ninety six kilogram per cubic metre). The frame will have a provision of G.I. Anchor fastners 14 nos (fourteen number) ( 5 (five) each on vertical style & 4 (four) on horizontal style of size M10 x 80 (M ten into eighty) ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm (one hundred into eighty nine into three millimetre) for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 (thirty) micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded) including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 60 mm (sixty millimetre) thick glazed fire resistant door shutters of 120 min (one hundred twenty minimum) Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm (sixty millimetre int sixty millimetre) wide and bottom rail of 110 mm x 60 mm (one hundred ten millimetre into sixty millimetre) made out of 1.6mm (one point six millimetre) thick G.I. sheet (zinc coating not less than 120gm/m2 (one hundred twenty gram per square metre)) duly filled mineral wool insulation having density min 96 kg/ m3 (ninety six kilogram per cubic metre) and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm (one hundred into eighty nine into three millimetre) of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 (thirty) micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately) including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete including carriage of materials with in all leads, lifts and other incidentals. :

125mm (one hundred twenty five millimetre)

100mm (one hundred millimetre)

Providing and fixing corrosion resistant AISI-Grade stainless steel sliding door bolts with nuts and screws etc. complete including carriage of materials with in all leads, lifts and other incidentals.

300x16 mm (three hundred into sixteen millimetre)

250x16 mm (two hundred fifty into sixteen millimetre)

Providing and fixing corrosion resistant AISI-Grade stainless steel Tower bolts with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals.

200x10 mm (two hundred into ten millimetre)

150x10 mm (one hundred fifty into ten millimetre)

Providing and fixing Acoustic Wood wool Perforated Desigener tiles in combination with calcium sillicate tile Ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (one hundred twenty grams per square metre) (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm (twenty five millimetre wide into one point six millimetre) thick with flanges of 27 mm and 37mm (twenty seven millimetre and thirty seven millimetre), at 1200 mm (one thousand two hundred millimetre) centre to centre, one flange som fixed to the ceiling with dash fastener 12.5 mm dia x 50mm (twelve point five millimetre diametre into fifty millimetre) long with Omm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm (twenty five into ten into zero point five zero millimetre) of required length with nuts & bolts of required size all complete as per drawings, specification and direction of the Engineer in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Wooden perforated accoustical panel over 50mm (fifty millimetre) thick absorb wool insulation in combination with stretch fabric aphony Fibrette 600X600 mm (six hundred into six hundred millimetre) of approved shade tiles false Ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (one hundred twenty grams per square metre) (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm (twenty five millimetre wide into one point six millimetre) thick with flanges of 27 mm and 37mm (twenty seven millimetre and thirty seven millimetre), at 1200 min (one thousand two hundred minimum ) centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm (twelve point into five millimetre into fifty millimetre) long with 6mm (six millimetre) dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm (twenty five into ten into zero point fifty millimetre) of required length with nuts & bolts of required size all complete as per drawings. specification and direction of the Engineer in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 120X60X12 mm (one hundred twenty int sixty into twelve millimetre) thick ply finished with 4mm (four millimetre) vaneer of delux prolad/Himalian with Rai wood borders, laid over absorb wool 50mm (fifty millimetre) thick insulation, polished in natural approvd shade false Ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (one hundred twenty grams per square metre) (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm (twenty five millimetre wide into one point six millimetre) thick with flanges of 27 mm and 37mm (twenty seven millimetre and thirty seven millimetre) , at 1200 min (one thousand two hundred minimum) centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm (twelve point five millimetre diametre into fifty millimetre) long with 6mm (six millimetre) dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm (twenty five into ten into zero point five millimetre) of required length with nuts & bolts of required size all complete as per drawings. specification and direction of the Engineer in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing of Wooden slats of approved shade 2440mm x128mm x 16mm (two thousand four hundred forty millimetre into one hundred twenty eight millimetre into sixteen millimetre) made MDF backed with acoustical fleece to be installed with 15mm (fifteen millimetre) GI and Lock in Clips on the back of tongue and groove system to be installed with 2400x50mm (two thousand four hundred into fifty millimetre) web flenges 15 and 50mm (fifteen and fifty millimetre) fully with backing of 50mm (fifty millimetre) thick absorb wool/insulation knurled hot depped galavanised steel with 120 GSM Zink coating of Prolad/ Himalayan/ Armstrong. The high grade MDF panels shall be melamine laminate of size 2440mm x128mm x 18mm (two thousand four hundred forty millimetre into one hundred twenty eight millimetre into eighteen millimetre) with 2mm (two millimetre) groove at 14mm (fourteen millimetre) pitch, Tongue and Groove edges for seamless mounting having density of 800kg/m3 (eight hundred kilogram per cubic metre) (base panel confirming to IS 12406 and laminated panel confirming to IS 14587). The back of the panels are perforated with a nonwoven fabric covering of 0.2mm ( zero point two millimetre) for providing Sound absorption via the acoustic impedance method. Panel is fixed by using GI Framework 2400mmx50mmx0.50mm (two thousand four hundred millimetre into fifty millimetre into zero point fifty millimetre) spaced at 600mmx600 (six hundred millimetre into six hundred millimetre) c/c & 16 mm (sixteen millimetre) WPC framework spaced at 400mm (four hundred millimetre) centers with suitable brackets and the system is backline with 50 mm (fifty millimetre) Rockwool insulation@48kg density and along with all accessories or Screw the aluminum extruded profile for channeled woodworks provided by manufacture over the lowest and second wooden batten at an on- center distance of 600mm (six hundred millimetre). Install the first set of wooden panels by inserting the clips for border channeled woodworks and insert the groove of the panel into the projecting flange of the aluminum clip. Continue installing rows of panels by inserting the tongue into the groove of the earlier inserted panel and progressively installing clips for inside channeled woodworks into the next keel till the actual height is achieved. Use clips for border channeled woodworks to finish off the installation. MAKE: PROLAD/ ECOPHONE/ HERADESIGN including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and Fixing Fabric Acoustical Panels in combination with wood fiber cement composite slats 20mm (twenty millimetre) thick with colours of approved shade size 2400x50mm (two thousand four hundred into fifty millimetre) web Flenges 15mm and 50mm (fifteen millimetre and fifty millimetre) fully with backing of 50mm (fifty millimetre) thick absorb wool/insulation above of Himalayan/Prolad/Armstrong or its Equivalent. Including required framework complete in all respect. The Grid should be 24 mm (twenty four millimetre) wide T sections i.e. the Main Runner 3000mm (three thousand millimetre) in web height of 32 mm (thirty two millimetre), 1200 mm & 600 mm (one thousand two hundred millimetre and six hundred millimetre) Cross Tees in web height of 26mm (twenty six millimetre) to comprise main runner spaced at 1200mm (one thousand two hundred millimetre) centers securely fixed to the structural soffit using suspension system at 1200mm (one thousand two hundred millimetre) maximum centre. The First/Last suspension system at the end of each main runner should not be greater than 450mm (four hundred fifty millimetre) from the adjacent wall. Flush fitting 1200mm (one thousand two hundred millimetre) long cross tees to be interlocked between main runners at 600mm (six hundred millimetre) centre to form 1200 x 600 mm (one thousand two hundred into six hundred millimetre) module. Cut cross tees longer than 600mm (six hundred millimetre) require independent support. 600 x 600mm (six hundred into six hundred millimetre) module to be formed by fitting 600mm (six hundred millimetre) long flush fitting cross tees centrally between the 1200 mm (one thousand two hundred millimetre) cross tees. Perimeter trim to be wall angles of size 3000x19x19mm (three thousand into nineteen into nineteen millimetre), secured to walls at 450 mm (four hundred fifty millimetre) maximum centers and as per the drawing and the work complete in all respects to the satisfaction of Engineer in-charge. MAKE: HERADESIGN/PROLAD/ECOPHON including carriage of materials with in all leads, lifts and other incidentals.

Providing and Fixing 10mm (ten millimetre) wall/partitions of Interior Grde High Pressure Laminate 6mm (six millimetre)/8mm (eight millimetre)/10mm (ten millimetre) thick upto 2.1 cm (two point one centimetre) height with fire resistant chimical resistant,boiling water resistant,envoirnment frendly green DNA with no uria content to be installed with stainless steelfittings,of GREENLAM/MERINO complete as per drawings. specification and direction of the Engineer in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 19 mm (nineteen millimetre) thick water proof termite resistant commercial board box including shelves and shutters, the back side cup board / cabinet shall be 8 mm (eight millimetre) thick ply and all the cut portions of shelves shall be finished with 6 mm (six millimetre) thick hard wood edging. The cut portion of shutters from all sides shall also be finished with 12 mm (twelve millimetre) thick hard wood edging. The shutter from out side shall be finished with 4 mm (four millimetre) thick vaneer Ply of approved shade to match with panelling including stainless steel hinges hinges and magnetic catcher with in all accessories etc. complete as per detailed drawing as per direction of Engineer-in-charge including all leads, lifts and carriage of material and other incidental.

Providing and fixing 75mm x60mm (seventy five millimetre into sixty millimetre) moulded hand rails in straight length complete in 1st class Indian Teak wood including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and Fixing 8mm (eight millimetre) thick wooden Laminated flooring made in superior water Resistant High Density hard wood fibre board make action tesa of approved shade including fixing with all accessories as per drawing and direction of Engineer in charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L- Type sections, made of 2.50 mm (two point five millimetre) thick M.S. Hollow steel Frame Member having single rebate of size 100X50 mm (one hundred into fifty millimetre) and double rebate of size 130X65 mm (one hundred thirty into sixty five millimetre) made of galvanised sheet of Zinc coat 120 gm/sqm (one hundred twenty grams per square metre) of Apollo chaukhat/TATA Parivesh/NCL Secoolar or its equivalent, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm (fifteen into three millimetre) lugs 10 cm (ten centimetre) long kg embedded in cement concrete block 15x10x10 cm (fifteen into ten into ten centimetre) of C.C. 1:3:6 (One Cement : Three coarse sand : Six graded stone aggregate 20 (twenty) mm nominal size) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, kg railings, brackets, gates and similar works including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm (one point sixty six millimetre to two millimetre) thick in eaves board / facia / soffits / ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) including carriage of materials with in all leads, lifts and other incidentals.

2) Providing and fixing in positioning of high strength structural bolts (Property class 8.8/10.9 as per IS:1367 and product grade ‘C’ as per IS:1363) confirming to IS:3757 and high strength structural hardened and tempered nuts (Property class ‘8’/10 as per IS:1367) confirming to IS:6623 with hardened and tempered washers as per IS 6649 etc., up to and inclusive of 39 mm (thirty nine millimetre) diameter and 300 mm (three hundred millimetre) long including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing roofing consist of 0.8 mm (zero point eight millimetre) thick galvanized steel deck sheet confirming to IS 277:1992 used as permanent shuttering over which MS wire mesh 3mm (three millimetre) laid at 100x100 mm (one hundred into one hundred millimetre) grid including edge trim covered with concrete. This metal deck will be supported on structural steel beam with shear studs. (Structural steel like Beam, column, joists etc. & concrete of different grade as per design will be paid separately) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Cement concrete flooring 1:2:4 (One cement : Two coarse sand : Four graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm (forty millimetre) thick with 20 mm (twenty millimetre) nominal size stone sqm aggregate including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm (eighteen millimetre) thick stone slab over 20 mm(twenty millimetre) (average) thick base of cement mortar 1:4 (One cement : Four coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, sqm Cherry Red, Elite Brown, Cat Eye or equivalent including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Stone tile (polished) work for wall lining over 12 mm (twelve millimetre) thick bed of cement mortar 1:3 (One cement : Three coarse sand) and cement slurry @ 3.3 kg/sqm (three point three kilogram per square metre) including pointing in white cement complete. Granite of any colour and shade including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (three hundred into three hundred millimetre) (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm (twenty millimetre) thick cement mortar 1:4 (One Cement : Four Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm (three point three kilogram per square metre) including pointing the joints with white cement and matching pigment etc., complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing And fixing glazed Digital tiles 300x600 x 8 mm (three hundred into six hundred into eight millimetre) thick of approved Shade and manufacturer in skirting risers of steps and dado 12 mm (twelve millimetre) thick cement mortar 1:3(One cement :Three sand) and jointed with cement slurry including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and laying anti skid matt finish full body vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (twenty millimetre) thick cement mortar 1:4 (One cement : Four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete : Tile size 600 X 600 mm (six hundred into six hundred millimetre) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % (zero point zero eight) and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm (twelve millimetre) thick bed of cement mortar 1:3 (One cement: Three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete : Size of tile 600x600 mm (six hundred into six hundred millimetre) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing GRC clading of Unistone/NTC tiles 10 mm (ten millimetre) thick of approved shade on R.C.C.surface side as on faces of Arches, masonry walls etc on 12mm (twelve millimetre) thick cement 1:3 (One cement: Three sand) and jointed with cement slurry including scafolding etc as per approved drawing/pattern and directions of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 0.60mm (zero point sixty millimetre) thick prepainted insulated steel sheet sand-wich puf roofing, with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating to back coat of polyster of 5 (Five) microns over 5 (five) microns primer coating,the thickness of puff should not be less than 5 mm (five millimetre) and wt.of puff shoud be 35-37 kg (thirty five to thirty seven kilogram) per cubic metre including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 15 cm (fifteen centimetre) wide, 45 cm (forty five centimetre) overall semi- circular plain G.S. sheet gutter with iron brackets 40x3mm (forty into three millimetre) size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. : 0.80 mm (zero point eighty millimetre) thick with zinc coating not less than 275 gm/m2 (two hundred seventy five grams per square metre) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately) : 6 mm (six millimetre) thick Cement bonded wood particle board as per IS:14276 including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimetre) gap for thermal expansion, Single socketed pipes. : 110 mm (one hundred ten millimetre) diameter including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimetre) gap for thermal expansion including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Coupler :110 mm (one hundred ten millimetre)

Single tee without door :110x110x110 mm (one hundred ten into one hundred ten into one hundred ten millimetre)

Bend 87.5° 110 mm (eighty seven point five degree one hundred ten millimetre) bend

110 mm (one hundred ten millimetre) Shoe

Providing and fixing 110mm (one hundred ten millimetre) unplasticised -PVC pipe clips of design to unplasticised - PVC rain water pipes by means of 50x50x50 mm (fifty into fifty into fifty millimetre) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 ( One cement: Four coarse sand) and making good the wall etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm (six hundred into six hundred millimetre) module which includes providing and fixing 'C' wall angle of size 20x30x20 mm (twenty into thirty into twenty millimetre) made of 0.5 mm (zero point five millimetre) thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm (three hundred millimetre) center to centre, suspending the main C carrier of size 10x38x10 mm (ten into thirty eight into ten millimetre) made of G.I steel 0.7 mm (zero point seven millimetre) thick from the soffit with help of soffit cleat 37x27x25x1.6 mm (thirty seven into twenty seven into twenty five into one point six millimetre), rawl plugs of size 38x12 mm (thirty eight into twelve millimetre) and C carrier suspension clip and main carrier bracket at 1000 mm (one thousand millimetre) c/c. Inverted triangle shaped Spring Tee having height of 24 mm (twenty four millimetre) and width of 34 mm (thirty four millimetre) made of Gl steel 0.45 mm (zero point five millimetre) thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm (six hundred millimetre) centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (one hundred twenty grams per square metre) (both side inclusive), fixing with clip in tiles into spring T with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 (six hundred into six hundred and 0.5 mm (zero point five millimetre) thick with 25 mm (twenty five millimetre) height, made of G I sheet having galvanizing of 100 gms/ sqm (one hundred grams per square metre) (both sides inclusive) and electro statically polyester powder coated of thickness 60 (sixty) microns (minimum), including factory painted after bending including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing ridges or hips 60 cm (sixty centimetre) overall with 0.60mm (zero point sixty millimetre) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6mm (six millimetre) dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing valley 90 cm (ninety centimetre) overall 0.60mm (zero point sixty millimetre) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing flushing 38cm (Thirty eight centimetre) overall with 0.60mm (zero point sixty millimetre) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia meter & prepainted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing, supplying and installation of Microcell Polycarbonate 20mm (twenty millimetre) thick (minimum). UV protected panel system which shall be uniform in colour with an integral microcell core. They should be manufactured with vertical standing seam with standing seam height of 10 to 20 mm (ten to twenty millimetre) at both sides of the panel. Panels shall be fixed on MS/trusses, purlins with continuous structural aluminium double wall I-profile spacer together with snap-on connector. These connectors to interlock the panel shall have to 2-4 (two to four) tooth grip-lock locking mechanism to ensure maximum uplift capability and shall pass a pull-out load of minimum 4000 N (4kN) when tested as per ISO 6892:1998 and IS 1608:2005. Panel shall be with additional End-Cap/ aluminium U-profile (mill finish) for ends including glass wool 100 mm (one hundred millimetre) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

15 mm (fifteen millimetre) cement plaster on rough side of single or half brick wall of mix: 1:6 (One cement: Six coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

15 mm (fifteen millimetre) cement plaster on rough sides of brick wall finished with a floating coat of neat cement of mix : 1:3 (One cement: Three fine sand) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Finishing walls with 100% (one hundred percent) Premium acrylic emulsion paint having VOC less than 50 gm/litre (fifty grams per litre) and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.: New work (Two or more coats applied @ 1.43 litre/ 10 sqm (one point forty three litre per ten square metre). Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm (zero point ninety litre per ten square metre) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm (zero point ninety litre per ten square metre) over an under coat of primer applied @ 0.80 ltr/ 10 sqm (zero point eighty litre per ten square metre) of approved brand and manufacture including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

French spirit polishing : Two or more coats on new works including a coat of wood filler including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and applying white cement based putty of average thickness 1 mm (one millimetre), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Wall painting two coats with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre (fifty grams per litre) of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and laying matt finished vitrified tile of size 100x100x16mm (one hundred into one hundred into sixteen millimetre /300X300X16 mm (three hundred into three hundred into sixteen millimetre) having water absorption less than 0.5% (zero point five percent) and conforming to IS: 15622 of approved make in all colours and shades in out door floors such as footpath, court yard multi models etc., laid on 20mm (twenty millimetre) thick base of cement mortar 1:4 (One cement : Four coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying matt finished vitrified tile of size 300x300 x 9.8mm (three hundred into three hundred into nine point eight millimetre) having with water absorption less than 0.5% (zero point five percent) and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm (twenty millimetre) thick base of cement mortar 1:4 (One cement : Four coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in- Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm (three hundred into three hundred into nine point eight millimetre) having with water absorption less than 0.5% (zero point five percent) and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm (twenty millimetre) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm (fifty millimetre) thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in- Charge including carriage of materials with in all leads, lifts and other incidentals.

60mm (sixty millimetre) thick cement concrete paver block of M-35 (Thirty five) grade with ii. approved colour, design and pattern

80mm (eighty millimetre) thick cement paver block of M-30 (thirty) grade with approved color design and pattern.

Providing and fixing 10x10x7.50 cm (ten into ten into seven point five centimetre) Granite stone block hand cut and chisel dressed on top, for paving in floors,drains etc. laid over 20mm (twenty millimetre) thick base mortar 1:4 (One cement : Four coarse sand) with joints 10mm (ten millimetre) wide filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and placing in position 100 mm (One hundred millimetre) thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 (twenty five) grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm (eight millimetre) dia TMT bars of Fe 500 (five hundred) grade @ maximum 100mm (one hundred millimetre) center to center on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm (one point six millimetre) thick , 100 mm (one hundred millimetre) wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 (two) Nos. 12 mm (twelve millimetre) dia bar for hooks etc. including cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and Fixing Structural Glazing fabricated from Roll formed sections made of Pre-painted Steel / Powder coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 Gm/Sqm) with total coated thickness of 0.72mm (zero point seventy two millimetre). The glass holding section made of 304 grade stainless steel of 0.58mm (zero point fifty eight) thick. Galvanized steel sections are to be sued as stiffeners inside the colour coated steel/powder coated sections as per the design requirement. Design calculations are made of suit wind pressures as given in IS 875. Paint Specifications:- Coated sections should be with Primer coat with epoxy primer of 5 – 7 (five to seven) microns thick, finish painted with a polyester paint of 12-16 (twelve to sixteen) microns thick and back coated with Alkyd backer of 5-7 (five to seven) microns or powder coated with pure polyester powder up to 50-60 (fifty to sixty) microns thick. Dimensions of Sections: The vertical section should be of 50mm x100mm x 0.72mm (fifty millimetre into one hundred millimetre into zero point seventy two millimetre), 33mm x 58mm x 0.72mm (thirty three millimetre into fifty eight millimetre into zero point seventy two millimetre) for frame horizontal section, stiffener section should be 48mm x 98mm x 1mm (forty eight into ninety eight into one millimetre), cover profiles sections should be of 20mm x 58mm x 0.58mm (twenty into fifty eight into zero point fifty eight millimetre), Glass holding section should be of 37mm x 37mm & 37mm x 18mm (thirty seven into thirty seven and thirty seven into eighteen millimetre). Fixing Details: Brackets made of CRCA powder coated/Electroplated should be used to connect vertical to horizontal, vertical to slab, to fix verticals at top & bottom as per site requirement. Gasket made of Ethyl Propylene Diamine Monomer. Natural cure, with Good U.V. Resistance Silicon to be used. Wall fixing of sections to concrete/masonry wall should be with self-expanding cap & screws.

Providing, assembling and supplying vision glass panels (IGUS) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified,comprising of an outer heat strengthened float glass 6mm thick, ofapproved colour and shade with reflective soft coating on surface #2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm (twelve millimetre) wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as sqm directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor."(Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No. )"For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant)provided and fixed in position, shall be measured in sqm."(i) Coloured tinted float glass 6mm (six millimetre) thick substrate with reflective soft coating on face # 2, + 12mm (twelve millimetre) Airgap + 6mm (six millimetre) Heat Strengthened clear Glass of lapproved make having pronerties as visible Light transmittance (VLT) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and Fixing Top Hung shutters in Structural Glazing fabricated from Roll formed sections made of Pre-painted Steel / Powder coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 (one hundred twenty grams) Gm/Sqm) with total coated thickness of 0.72mm (zero point seventy two millimetre). The glass holding section made of 304 grade stainless steel of 0.58mm (zero point fifty eight) thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel/powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS 875. Primer coat with epoxy primer of 5-7 (five to seven) microns thick and back coated with Alkyd backer of 5-7 (five to seven) microns or powder coated with pure polyester powder up to 50-60 (fifty to sixty) microns thick. The outer frame should be of 20mm x 58mm x 0.58mm (twenty into fifty eight into zero point fifty eight millimetre), Shutter section should be of 58mm x 33mm x 0.72 mm (fifty eight into thirty three into zero point seventy two millimetre), stiffener section should be 55mm x 31mm x 1mm (fifty five into thirty one into one millimetre). EARL Bihari Hinges – 2 (two) Nos for each shutter and Aluminum Stays – 2 (two) Nos. for each shutter, Aluminum Handle – 1(one) no. for each shutter including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto any lead including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm (twenty centimetre) in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within all lead : All kinds of soil Pipes, cables etc, not exceeding 80 mm (eighty millimetre) dia including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm (five centimetre to twenty centimetre) in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. including carriage of materials with in all leads, lifts and other incidentals.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm (one point five millimetre to two millimetre) in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in- charge. including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing in position pre-cast reinforced cement concrete manhole cover and frame of required shape and approved quality : Rectangular shape 600x450 mm (six hundred into four hundred fifty millimetre) internal each dimensions including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Water Supply & Sanitary installation Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

20 mm (twenty millimetre) nominal bore

32mm (thirty two millimetre) nominal bore

15 mm (fifteen millimetre) nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :. 25 to 40 mm (twenty five to forty millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing Polyethelene-Aluminium Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 (one metre) metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge. Concealed work, including cutting chases and making good the wall etc. including carriage of materials with in all leads, lifts and other incidentals.

2532 (twenty thousand five hundred thirty two) (32 mm OD) (thirty two millimetre) pipe

2025 (two thousand twenty five) (25 mm OD) ( twenty five millimetre) pipe

1620 (one thousand six hundred twenty) (20 mm OD) (twenty millimetre) pipe

1216 (one thousand two hundred sixteen) (16 mm OD) (sixteen millimetre) pipe

Providing and fixing white vitreous china Angel C8915 wall mounting water closet of size 455x355x355 mm (four hundred fifty five into three hundred fifty five into three hundred fifty five millimetre) of approved shape including seat cover, and cistern fittings, nuts,bolts and gasket etc of Perryware , Cera,Jaquar, Hindware or equivelent complete as per direction Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing white vitreous china CURSE SET WC cat No. S1021114P extended wall mounting water closet of size 780x370x810 mm (seven hundred eighty into three hundred seventy into eight hundred ten millimetre) of approved shape including providing & fixing white vitreous china cistern Cat No. S1060106 with dual flush fitting, of flushing capacity 3 (three) litre/ 6 (six) litre (adjustable to 4(four) litre/ 8(eight) litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc of Perryware , Cera,Jaquar, Hindware or equivelent complete as per direction Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing viterous China CASCADE NXT C0207 Wall Hung Closet 540x365x395 (five hundred forty into three hundred sixty five into three hundred ninety five) White Shade Wall hung WC with soft close seat cover, hinges, accessories set size mm of /Jaquar or equivalent complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing Single piece slim concealed cistern with floor mounting frame installation kit and S-type Drain pipe conection set for wall hung WC (without flush control Plate) JCS-WHT-2400FS of Jaquar or equivalent including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing Flushing Plate Control palate vignette prime (JCP-CHR-812415) Jaquar or equavalent including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing viterous China wash basin C8863(505x405x155) (five hundred five into four hundred five into one hundred fifty five) Basin (half Pedestal) In White Shade of Perryware /jaquar/ Hindware/ Cera or equivalent including cutting holes & making good the same and carriage of materials within all leads and lifts :- Of Superior quality as per direction of Engineer-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing viterous China wash basin CRUSE SET CAT NO S2040101 Wash Basin 510 x 400mm (five hundred ten into four hundred millimetre) and pedestal cat no. S2090101 of perryware /jaquar/ Hindware/ Cera or equivalent including cutting holes & making good the same and carriage of materials within all leads and lifts :- Of Superior quality as per direction of Engineer-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing viterous China wash basin CASCADE NXT C0404 Basin With Half Pedastal C0379 In White Shade of Perryware /jaquar/ Hindware/ Cera or equivalent including cutting holes & making good the same and carriage of materials within all leads and lifts :- Of Superior quality as per direction of Engineer-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous China Flat back urinal ASTUTE C 0586 ASTUTE water less Urinal 345 x365x 655 (three hundred forty five into three hundred sixty five into six hundred fifty five) In White Shadeof Perryware /jaquar/ Hindware/ Cera or equivalent including cutting holes & making good the same and carriage of materials within all leads and lifts :- Of Superior quality as per direction of Engineer-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm ( forty millimetre), including painting of fittings and brackets, cutting and making good the walls wherever required 510x1040 mm (five hundred ten into one thousand forty millimetre) bowl depth 250 (two hundred fifty) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40mm (forty millimetre) dia including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm (forty five centimetre) length 15 mm (fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete New work 40mm (forty millimetre) dia including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing 600x450 mm (six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing C.P. brass long nose bib cock Cat no.CON 107KN Jaquar or equivalent single control of approved quality conforming to IS standards. 15 mm (fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing C.P. brass long nose bib cock Cat no.OPP -15037PM Jaquar or equivalent single control of approved quality conforming to IS standards. 15 mm (fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and Fixing Swan neck pillar tap with left hand operating knob single control CON-CHR-123BKN of Jaquar or equivalent complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and Fixing OPP-15001PM Pillar cock Jaquar or equivalent as per direction of Engineer-in- charge. complete including carriage of materials with in all leads, lifts and other incidentals

Providing and Fixing Angular stop cock with wall flange of opel prime no. CON 150083KN Stop Cock of jaquar or equavalent complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and Fixing Concealed stop cock with wall flange of opel prime no. CON 083FTK Stop Cock PM single control of jaquar or equavalent complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and Fixing Angular stop cock with wall flange of opel prime no. OPP-15053PM jaquar or equavalent complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and Fixing Angular stop cock with wall flange of opel prime no. CON 053KN of jaquar or equavalent single control complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing C.P.Mixer for kitchen sink with casted swinging CON 309KN jaquar or equavalent complete In all respect including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and Fixing Soap dish recessed type stainless steel AHS-1531 of Jaquar or equivalent complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and Fixing Soap dish stainless steel CAN -1131N of Jaquar or equivalent complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing Towel Rack with lower hanger No. AHS-1581H of hotelier series of JAQUAR, or equivalent of superior quality as per direction of Engineer-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Corner glass self with bract No.ACN-1173 of hotelier series of JAQUAR, ESS-ESS or equivalent of superior quality as per direction of Engineer-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Glass shelf 550 mm (five hundred fifty millimetre) long with C.P. Brass bracket and guard rail no. AQN-7771 of Jaquar or equivalent fixed with C.P. Brass screws etc complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing U Shaped wall mounted rail with hinges 600 x 100mm (six hundred into one hundred millimetre)Cat No. B2210107 and Wall Mounted Grab Bar 600mm (six hundred millimetre) Long CAT No. B2210106 jaquar or equivalent Superior quality as per direction of Engineer-Charge. Jaquar including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 8 mm (eight millimetre) dia C.P. / S.S. Jet with flexible tube upto 1 (one) metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

25mm (twenty five millimetre)

20mm (twenty millimetre)

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

15mm (fifteen millimetre)

20mm (twenty millimetre)

32mm (thirty two millimetre)

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 15 mm (fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing 110 mm (one hundred ten millimetre) high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing 150 mm (one hundred fifty millimetre) high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing 110 mm X 90 mm (one hundred ten millimetre into ninety millimetre) PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing PVC door bend with ovalaccess door, insertion rubber washer 3 mm (three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

110 mm (one hundred ten millimetre) dia

150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

110 mm (one hundred ten millimetre) dia

150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC plain double equal branch ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

110 mm (one hundred ten millimetre) dia

150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

110 mm (one hundred ten millimetre) dia

150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc.complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

110 mm (one hundred ten millimetre) dia

150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

110 mm (one hundred ten millimetre) dia

150 mm (one hundred fifty millimetre) dia

Constructing brick masonry manhole in cement mortar 1:4 ( One cement : Four coarse sand ) with R.C.C. top slabwith 1:1.5:3 mix (One cement : 1.5 (One point five coarse sand (zone- III) : Three graded stone aggregate 20 mm (twenty millimetre) nominal size), foundation concrete 1:4:8 mix (One cement : Four coarse sand (zone- III) : eight graded stone aggregate 40 mm (forty millimetre) nominal size), inside plastering 12 mm (twelve millimetre) thick with cement mortar 1:3 (One cement : Three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement : Two coarse sand : Four graded stone aggregate 20 mm (twenty millimetre) nominal size) finished with a floating coat of neat cement complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.Inside size 120x90 cm (one hundred twenty into ninety centimetre) and 90 cm (ninety centimetre) deep including C.I. cover with frame (medium duty) 500 mm (five hundred millimetre) internal diameter, total weight of cover and frame to be not less than 116 kg (one hundred sixteen killogram) (weight of cover 58 kg (fifty eight killogram) and weight of frame 58 kg (fifty eight killogram)) :With Sewer bricks conforming to IS : 4885

Constructing soak pit 1.20x1.20x1.20 m (one point twenty into one point twenty into one point twenty metre) filled with brickbats including S.W. drain pipe 100 mm (one hundred millimetre) diameter and 1.20 m (one point twenty metre) long complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Constructing masonry Chamber 90x90x100 cm (ninety into ninety into one hundred centimetre) inside, inbrick work in cement mortar 1:4 (One cement : Four coarse sand) for sluice valve, with C.I. surface box 100 mm (one hundred millimetre) top diameter, 160 mm (one hundred sixty millimetre) bottom diameter and 180 mm (one hundred eighty millimetre) deep (inside) with chained lid and RCC top slab 1:2:4 mix (One cement : Two coarse sand : Four graded stone aggregate 20 mm (twenty millimetre) nominal size ), including necessary excavation, foundation concrete 1:5:10 (One cement : Five fine sand : Ten graded stone aggregate 40 mm (forty millimetre) nominal size ) and inside plastering with cement mortar 1:3 (One cement : Three coarse sand) 12 mm (twenty millimetre) thick, finished with a floating coat of neat cement complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (One cement : Two fine sand) including testing of joints etc. complete 450 mm (four hundred fifty millimetre) dia RCC pipes including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Electrical installation and Yard Lighting Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq.(one point five square) mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit with modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq. (one point five square)mm. HRFRLS/PVC insulated single core copper conductor cable as required complete in all respect. Cable Make: PLAZA / FINOLEX / UNITECH / BONTON / KEI / BIYANI / GEMSCAB / CMI . including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Wiring for twin control light point with 1.5 Sq. (one point five square) mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit with 2-way, 5/6 amps. modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq. (one point five square)mm. HRFRLS/PVC insulated single core copper conductor cable as required complete in all respect.Cable Make: PLAZA / FINOLEX / UNITECH / BONTON / KEI / BIYANI / GEMSCAB / CMI . including carriage of materials with in all leads, lifts and other incidentals. as per direction of Engineer-in- charge.

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 1 No.HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required complete in all respect.Cable Make: PLAZA / FINOLEX / UNITECH / BONTON / KEI / BIYANI / GEMSCAB / CMI . including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

2x1.5 Sq. mm. (two into one point five square millimetre)

2x4.0 Sq. mm. (two into four square millimetre)

2x6.0 Sq. mm. (two into six square millimetre)

2x10 Sq. mm (two into ten square millimetre)

Wiring for power plug with 4x4 Sq. mm (four into four square millimetre). PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 2 (two) No.4 Sq.mm (four square millimetre) HRFRLS/PVC insulated single core copper conductor cable for earthing as required complete in all respect.Cable Make: PLAZA / FINOLEX / UNITECH / BONTON / KEI / BIYANI / GEMSCAB / CMI . including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Wiring for circuit / sub-main with 4x10 Sq. mm (four into ten square millimetre) PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 2 (two) No.10 Sq.mm (ten square millimetre) (4x10+2x10) HRFRLS/PVC insulated single core copper conductor cable for earthing as required complete in all respect.Cable Make: PLAZA / FINOLEX / UNITECH / BONTON / KEI / BIYANI / GEMSCAB / CMI . including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Wiring for circuit / sub-main with 4x16 Sq. mm.(four into sixteen square millimetre) PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 2 No.16 Sq.mm. (4x16+2x16) HRFRLS/PVC insulated single core copper conductor cable for earthing as required complete in all respect.Cable Make: PLAZA / FINOLEX / UNITECH / BONTON / KEI / BIYANI / GEMSCAB / CMI .including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Wiring for circuit / sub-main with 3x25+1x16 Sq. mm.(three into twenty five plus one into sixteen square millimetre) PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 2 No.16 Sq.mm. (3x25+3x16) HRFRLS/PVC insulated single core copper conductor cable for earthing as required complete in all respect.Cable Make: PLAZA / FINOLEX / UNITECH / BONTON / KEI / BIYANI / GEMSCAB / CMI . including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Supplying and drawing following size of PVC insulated, heat resistant, flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in existing surface / recessed, Steel/PVC conduit as required complete in all respect.Cable Make: PLAZA / FINOLEX / UNITECH / BONTON / KEI / BIYANI / GEMSCAB / CMI . including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. 3x1.5 Sq. mm.(three into one point five square millimetre)

Providing, laying and fixing of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade on surface etc. of the required size complete in all respect.Cable Make: PLAZA / FINOLEX / UNITECH / BONTON / KEI / BIYANI / GEMSCAB / CMI . including carriage of materials with in all leads, lifts and other incidentals Armoured cable 185 sq. mm (one hundred eighty five square millimetre) (3.5 core) (three point five)

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1(one) meter below the ground level including excavation sand cushioning, protective covering and refilling the trench etc. of the required size complete in all respect as per entire satisfaction of Engineer- in- Charge. Cable Make : CCI/ Universal/ Finolex / Polycab / Rallison / Grandlay / KEI. including carriage of materials with in all leads, lifts and other incidentals.

Armoured cable 25 sq. mm (twenty five square millimetre) (twin core)

Armoured cable 50 sq. mm (fifty square millimetre) (twin core)

Armoured cable 6 sq. mm (six square millimetre) (twin core)

Supplying and drawing following pair of Fire Retardant, PVC insulated 0.5 sq.mm. (zero point five square millimetre) (FR-Flexible) copper conductor, flat, unarmoured, telephone cable in existing surface / recessed, steel / PVC conduit as required complete in all respect as per entire satisfaction of Engineer- in- Charge. including carriage of materials with in all leads, lifts and other incidentals .2 (two) Pair

Supplying and fixing of following sizes of PVC conduit along with the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as requiredcomplete in all respect MAKE:-AKG / BEC / NIC / DIPLAST including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. 25 mm. dia (twenty five millimetre dia meter)

Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required complete in all respect as per entire satisfaction of Engineer- in- Charge. Make : Legrand (Myriu) / L&T ( Entice) / Anchor /SSK / ABB (Similar Class). including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

S.P. 5/ 6 Amps one way Modular switch.

5 pin, 5/ 6 Amps Modular socket outlet.

Telephone socket outlet, Modular.

Supplying & fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required complete in all respect as per entire satisfaction of Engineer- in- Charge. including carriage of materials with in all leads, lifts and other incidentals 2 modules (78mmx78mmx50mm) (seventy eight millimetre into seventy eighty eight millimetre into fifty millimetre)

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) (one hundred forty millimetre into seventy eight millimetre into fifty millimetre) size with modular plate and cover in recess including providing and fixing 5 pin 5/6 amps modular socket outlet and 5/6 amps, modular switch, connections etc. as required complete in all respect as per entire satisfaction of Engineer- in- Charge. Make : Legrand (Myriu) / L&T ( Entice) / Anchor /SSK / ABB (Similar Class). including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) (one hundred forty millimetre into seventy eight millimetre into fifty millimetre) size with modular plate and cover in recess including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps, modular switch, connections etc. as required complete in all respect as per entire satisfaction of Engineer- in- Charge. Make : Legrand (Myriu) / L&T ( Entice) / Anchor /SSK / ABB (Similar Class). including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Supplying and fixing 20 (twenty) Amps, 240 (two hundred forty) volts, SPN industrial socket outlet, 2(two)-pole & earth, metal enclosed plug top, sheet steel enclosure, suitable to accommodate a 20 (twenty) Amp SPN-MCB/DP, on surface or in recess, with chained metal cover for the socket outlet, complete with connections, testing and commissioning etc. as required complete in all respect.Make : L&T / Legrand / ABB / SIEMENS. including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and fixing of Non-return valve, Dead weight safety valve, 2 (two)No C.P. connection rods 18" (eighteen inches) long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. as required complete in all respect as per entire satisfaction of Engineer- in- Charge. (Make : Racold / Bajaj / Usha.) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. 15 (fifteen) Litre capacity water heater (Cat-A)

Supplying and erection of 6 (six) amps. to 32 (thirty two) amps. rating, 10 (ten) KA breaking capacity, 240 (two hundred forty) volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required. MAKE :- LEGRAND / L&T/C&S/GE including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. Single pole. Cat-A.

Supplying and erection of 40/50/63 (forty/fifty/ sixty three)amps rating, 10 (ten) KA breaking capacity, 240 (two hundred forty) volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required complete in all respect. Make : L&T / Legrand / Siemens. including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. Double pole. Cat-A.

Supplying and fixing following rating, double pole (single phase & neutral) 240 (two hundred forty) volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required complete in all respect. Make : L&T / Legrand / Siemens. including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. 63 Amps. (sixty three ampere) Cat-A.

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 (two hundred forty) volts, on surface / recess, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required complete in all respect. Make : L&T / Legrand / Siemens. including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Double door-12 way (twelve way)

Double door-16 way (sixteen way)

Supplying and fixing sheet metal bus-bar chamber suitable for 63 (sixty three) Amp. 415 (four hundred fifteen) volts capacity with 4 (four) No. copper strip bus-bars each of length 300mm (three hundred millimetre) & cross-sectional area (16mmx3.17mm) (sixteen millimetre into three point seventeen millimetre), enclosure made from 1.6 mm(one point six millimetre) thick M.S. sheet having overall dimensions (380mmx350mmx150mm) (three hundred eighty millimetre into three hundred fifty millimetre into one hundred fifty millimetre) nominal with all accessories including connections, earthing the body etc. as required complete in all respect.Make : L&T / Legrand / ABB / SIEMENS. including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Supplying and fixing sheet metal bus-bar chamber suitable for 100 (one hundred) Amp. 415 (four hundred fifteen) volts capacity with 4 (four) No. copper strip bus-bars each of length 450mm (four hundred fifty millimetre) & cross-sectional area (25.4mmx3.17mm) (twenty five point four into three point seventeen millimetre), enclosure made from 1.6 mm (one point six millimetre) thick M.S. sheet having overall dimensions (530mmx400mmx150mm) (five hundred thirty into four hundred into one hundred fifty millimetre) nominal with all accessories including connections, earthing the body etc. as required complete in all respect.Make : L&T / Legrand / ABB / SIEMENS. including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Supplying and erection of wall mounted metal boards for switch gear mounting of suitable size, with permissible variation in size of plus minus 5mm (five millimetre), welded frame work made of M.S. angle iron 50 mm x 50 mm x 6 mm (fifty millimetre into fifty millimetre into six millimetre)thick duly welded complete with 3mm (three millimetre) thick M.S. sheet fixed with hinges as open able front, complete with locking arrangement including painting and bonding to the existing earth as required complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Earthing with copper earth plate 600 mmx600 mmx 3 mm (six hundred millimetre into six hundred millimetre into three millimetre) thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Supplying and laying 8 (eight) SWG Copper wire at 0.50 mtr. (zero point five zero metre) below ground level for earth electrode conductor, including soldering etc. as required complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing of lighting conductor finial, made of 25 mm dia. 300 mm (twenty five millimete diameter three hundred millimetre) long copper tube, having single prong at top, with 85 mm dia 3 mm (eighty five millimetre diameter three millimetre) thick copper base plate including holes etc. complete as required complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Riveting, sweating and soldering of copper/ G.I. tape ( with another copper/G.I. tape, base of the finial or any other metallic object) as required complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Supplying and fixing copper tape 20mmx3mm (twenty millimetre into three millimetre) thick on parapet or surface of wall for lightning conductor as required complete in all respect. ( for horizontal run) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Supplying and fixing copper tape 20mmx3mm (twenty millimetre into three millimetre) thick on parapet or surface of wall for lightning conductor as required complete in all respect. ( for vertical run) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Supplying and fixing stepped type Modular fan regulator on the existing modular box including making connections etc. as required complete in all respect as per entire satisfaction of Engineer- in- Charge. Make : Usha / Bajaj / Anchor Panasonic. including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) (thirty centimetre) with 16/0.20 mm (sixteen/zero point two zero millimetre) twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required complete in all respect. Make : Usha Ultimate / Bajaj Ultima / Anchor Panasonic. including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. Ceiling Fan 1200 mm (one thousand two hundred millimetre) sweep, Category-A

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required complete in all respect. Make: Bajaj , Usha, Anchor including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. Exhaust Fan, Light duty, (Domestic) 300 mm (three hundred millimetre) sweep

Supplying and fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required complete in all respect. Make :- ESS ESS KAY / Cona / Anchor including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Supplying and fixing of fancy wall bracket containing thread type CFL lamp holder (s) of all sizes and shapes, complete with all accessories but excluding CFL lamp including making connections, testing etc. as required complete in all respect. Make : Wipro / Bajaj / Phillips / Jaquar / (Twinkle) Lux Max including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. Fixed type wall bracket 150 dia (one hundred fifty millimetre diameter), single lamp.(Category-A)

Supplying and fixing of fancy wall bracket containing thread type CFL lamp holder (s) of all sizes and shapes, complete with all accessories but excluding CFL lamp including making connections, testing etc. as required complete in all respect. Make : Wipro / Bajaj / Phillips / Jaquar / (Twinkle) Lux Max including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. Mirror light 460 mm (four hundred sixty millimetre) , single lamp.(Category-A)

Supplying and erection of Galvanized Iron (G.I.) pipe pole 'A' quality of suitable length and dia. 4.47 mm (four point forty seven millimetre)thickness, including fixing up to a given depth below G/L.The hole of excavation about 30 (thirty) cm dia. and given depth to be filled in up to 15 (fifteen) cm below G/L with 1:3:6 (one cement : three sand : six aggregate) cement concrete and there above plinth with 1:2:4 (one cement : two sand : four aggregate) cement concrete up to a height of 45 (forty five) cm from G/L. The radial thickness of the plinth above G/L should not be less than 6.35 cm and sufficient to completely flush a 180 mmx100 mmx 45 mm (one hundred eighty into one hundred into forty five millimetre) deep, glass filled Nylan F.R. grade box for housing a 16 (sixteen) Amp. MCB, the outer surface of the plinth to be finished with 1:3 (one cement :three sand) cement plaster 6 mm (six millimetre) thick, the fuse-box shall have a water tight cover, including painting of pole with two coats of approved color, brand and manufacture of paint over a priming coat complete in all respects as required complete with all respect as per entire satisfcation of engineer in charge Bajaj / Twinkle/ K-Lite etc. including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge .4 (four) Meter long having nominal bore dia. 65 mm (sixty five millimetre) planting depth 80 cm (eighty centimetre) with pit depth 95 cm (ninety five centimetre)

Providing and fixing Energy efficient wall mounted LED Bulk Head luminaire made of pressure die cast aluminium housing and enclosed with poly carbonate cover IP65 complete with connection,testing and commissioning etc. as required complete in all respect as per entire satisfaction of Engineer- in- Charge Make : Wipro / Bajaj / Phillips / Jaquar / (Twinkle) Lux Max . including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing & fixing Glazed LED 20 (twenty) watt Batten High quality design aluminium extruded with decorative end caps complete with Connection,testing commissioning as required complete in all respect as per entire satisfaction of the Engineer in charge. Make : Wipro / Bajaj / Phillips / Jaquar / (Twinkle) Lux Max including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing & fixing Surface mounted Square LED downlight 15 (fifteen) Watt with Al die-cast body finish with drop down PC diffuser to deliver low glare illumination with optimized heat sink for efficient heat dissipation complete with Connection,testing commissioning etc as required in all respect as per entire satisfaction of the Engineer in charge. Make : Wipro / Bajaj / Phillips / Jaquar / (Twinkle) Lux Max including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and fixing LED recess / pendant 1x1 20 (twenty) watt Square pannel with aluminium die cast housing of superior quality complete with Connection,testing commissioning as required complete in all respect as per entire satisfaction of the Engineer in charge. Make : Wipro / Bajaj / Phillips / Jaquar / (Twinkle) Lux Max including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing & fixing LED Surface mounted 2x2 36 (thirty six) watt Square pannel with aluminium die cast housing of superior quality complete with Connection,testing commissioning as required complete in all respect as per entire satisfaction of the Engineer in charge. Make : Wipro / Bajaj / Phillips / Jaquar / (Twinkle) Lux Max including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Supplying and fixing 01 RJ-45 single for Cat-6 cable including connections, etc. as required complete in all respect as per entire satisfaction of Engineer- in- Charge including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Supplying and laying of Cat-6 cable of approved make as required complete in all respect and as directed by the Engineer in charge including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Supplying and fixing G I modular Box of 205 mm x78mmx50mm (two hundred five into seventy eight into fifty millimetre) size with modular plate and cover in recess including providing and fixing 3 Nos 5 pin 5/6 Amps modular socket outlet, 3 Nos 5/6 Amps modular switch, as required etc. as required complete in all respect complete in all respect as per entire satisfaction of Engineer- in- Charge. Make : Legrand (Myriu) / L&T ( Entice) / Anchor /SSK / ABB (Similar Class) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

MCCB63 Amp. With spread linker @ 405 per set =405 +4930= 5335 ( With Under volatage & over volatage protection) of thermal relaese range 63-80 of L& T make Cat No. CM90518 OOJO type DU 100D breaking capacity 18 KA or Legrand make including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

MCCB 100 (one hundred) Amp. With spread link = 1(one) set @ 405 (four hundred five) per set =405 +10490 (ten thousand four hundred ninety) = 10895 (ten thousand eight hundred ninety five) ( With Under voltage & over voltage protection) of thermal relaese range 100-120 of L& T make Cat No. CM90642 OONO type DU 250Cbreaking capacity 25 (twenty five) KA or Legrand make including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

Providing and Fixing Post top Lantern 25 (twenty five) watt Small LED Post top Fixture are made of dia. cast aluminium baase and spun aluminium round top, LED's are mounted directly on the 5 (five) wt. aluminium, heat sink . A thermoformed P.C. diffuser is provided in clear opal adn Prismatic finish as option complete with all accessories including making connections, testing etc as required complete in all respect Make:- Bajaj / (Twinkle) Lux Max / Anchor Panasonic / k-lite including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge.

KDN Infrastructure Pvt. Ltd.