PROVISION OF MEDITATION/ YOGA ROOM, CHAIN LINK FENCING AROUND TECHNICAL COMPLEX AND SPECIAL REPAIRS TO PARADE GROUND AND DRILL SHED AT NAVAL BASE PORBANDAR UNDER GE NAVY PORBANDAR

Amount

Surface dressing n exc 15 cm deep in hard/dense soil.

Surface excavation n. exc. 30 cm deep and averaging 15cm deep and getting out in hard/dense intrgrated rocks including cutting of bushes,saplings and cutting trees not exe 30m girth etc complete.

Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All as per Item No. 03.00 above but soft / disintegrated rock

All as per Item No. 03.00 above but hard rock

Excavation in trenches,n.exc. 1.5m wide and n.exc. 1.5m in depth for foundations etc. n.exc. 10 Sqm on plan and getting out in Hard / Dense soil.

Excavation in trenches,n.exc. 1.5m wide and n.exc. 1.5m in depth for foundations etc. n.exc. 10 Sqm on plan and getting out in soft / disintegrated rock.

All as above item no. 7.00 but depth 1.50m to 3.00m depth.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,in hard/dense soil including removing & disposal of soil outside MoD land all as specified & directed by Engr-in-charge.

Returning,filling in,including spreading,levelling,watering and well ramming in layers not exc 25cm in soil.

Returning,filling in,including spreading,levelling,watering and well ramming in layers not exc 25cm in Soft/disintegrated rock.

Removing excavated material soil exc 250 m but n exc 500m and depositing where directed at a leval n exc 1.5m above the starting point.

Removing excavated material (soil) exc. 500m but n exc. 1.5km and depositing where directed.

Removing excavated material rock exc 250 m but n exc 500m and depositing where directed at a leval n exc 1.5m above the starting point.

M&L Removing excavated rocks not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point.

M & L for Removing excavated soil to a distance not exc 50 mtr and depositing where directed at a level n exc 1.5 m above the starting point complete all as specified by the Engineer-in-charge.

M&L for form work to sides of concrete foundations, footings, bases of columns and plinth beams and similar work, complete all as specified and directed .

M&L for form work to sides of columns, square, rectangular, complete all as specified and directed .

M&L for form work to sides and soffits of roof beams, lintel beams etc. including supports, overhangs, etc. also splays between floors and beams, etc. fair finished complete all as specified and directed.

M&L for form work to sides and soffits of suspended slabs such as roof slabs, floor slabs and similar work N exc 200 mm thick (horizontal or sloping) fair finished complete all as specified and directed.

M&L for form work to chajjas including edges etc fair finished, complete all as specified and directed.

M&L for RCC type M-30 (20 mm graded aggregate) as in foundations,including rafts,footing plinth beams, bases for column etc. complete all as specified and directed.

M&L for RCC type M-30 (20 mm graded aggregate) as in column etc. complete all as specified and directed.

M&L for RCC type M-30 (20 mm graded aggregate) as in lintel beams, roof beams etc. complete all as specified and directed .

M&L for RCC type M-30 (20 mm graded aggregate) as in roof slab supported on walls, beams and columns in roofs etc. complete all as specified and directed .

M&L for RCC type M-30 (20 mm graded aggregate) as in chajjas etc. complete all as specified and directed .

M&L for providing RCC type B-1 1:2:4 (20mm graded aggr) in CM 1:4 in precast fencing post straining or terminal post strut etc for fencing average sectional area exe 100 sqcm but n exe 250 sqcm with or without chamferred angles and flat splayed rounded or metered tops complete all as specified

M & L for precast RCC cover slab for manholes in 1:2:4,Type B1 (20mm graded aggregate) set in cement mortar 1:6 including necessary form work and set in CM 1:6.

M&L for PCC type D2, 1:4:8 by using 40 mm graded aggregate as in foundations, filling and mass concrete or as in sub base complete all as specified and directed .

M&L 75mm thick PCC 1:3:6 type C2 as in plinth protection finished even & smooth without using extra cement complete all as specified and directed.

M&L 75mm thick PCC type D2 1:4:8 (40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for PCC 1:2:4 type B1(using 20mm graded stone aggregate) as in coping,bed plates, kerb not provided for etc complete all as specified and directed by Engr-in-Charge

M&L for PCC concrete 1:5:10 type E2 using 40 mm graded stone aggregate as in foundations, filling and mass concrete or as in sub base complete all as specified and directed.

M&L for PCC concrete 1:3:6 type C1 using 20 mm graded stone for coping of poles including formwork complete all as specified and directed.

M & L for Cutting the existing PCC floor/road/foot path not exeeding 15cm width,30 cm depth for laying of UG cable/protection of pipe all as directed.

M & L for PCC type B1,1:2:4 using 20 mm graded stone aggregate all as specified and directed.

M & L for cement concrete 1:3:6 Type C2 (using 40mm graded stone aggregate), as in foundations, filling and mass concrete complete all as specified and directed.

S&F Mild steel TMT (CRS) bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed .

S&F Mild steel TMT (CRS) bars 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed .

S&F Mild steel TMT (CRS) bars 8 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed .

M&L for Framed work as in doors, gates, trusses, sheds, posts etc of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete (Fe 410 -W (Gde- E- 250) quality- A)

S&F for posts and struts (angle) in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe0290 Gde E-165 complete all as specified and directed

S&F for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exe 5cm but n ece 10cm long and dia of neck 11 to 15 mm complete all as specified and directed.

S&F powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

M&L for preparation of old decorative steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint on old steel surfaces complete all as specified and directed.

S&F of factory made, 35mm thick, 2nd class hard wood (Hollock), plain framed, panelled shutters, any number of panels, panels shall be of 12mm thick BWR glade veneered particle board medium density, wood particle board with commercial face veneers, size of members as specified in clause 8.20(a) of MES Schedule Part-I section -8 complete all as specified.

Supply only integral water proofing compound.

M&L for Hardcore of broken stone or boulders of guage N. exc. 63 mm, deposited, spread and levelled in layeres N. exc. 150 mm thick, watered and rammed to a true surface, as in below sub base, plinth protection and ramp complete all as specified and directed.

M&L for Moorum / red bajri filling in floors or pavings, laid in layeres n. exc. 150 mm thick, spread, levelled and reammed including watering, complete all as specified and directed.

M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured)

M&L for treating the top surface of filled earth with anti termite emulsion at the rate of 5 litres per square metre of surface area,complete all as specified and as directed.

M&L for treating the soil under plinth protection / ramp with anti termite emulsion at the rate of 5 litres per square metre of surface area,complete all as specified and as directed.

M&L for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall

M&L Screed bed or bedding layer or mortar 15mm thick for laying floor tiles in cement mortar 1:6 finished rough to receive floor tiles Complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premisess complete all as specified and as directed

M&L Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L Joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match Complete all as specified and directed.

M&L coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L Machine cut Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed withwith grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite

M & L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with CM 1:4 , 15mm tk cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified & directed by Engr-in-charge.

M & L for 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over CM 1:3 , 10 mm tk cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified & directed by Engr-in-charge.

M&L for rendering 5 mm thick on fair faces of concrete surfaces as on ceiling surface, facia and projection of slabs, finished surfaces even and smooth without using extra cement, in CM (1:3) complete all as specified and directed.

M&L 10 mm thick rendering in CM (1:4) on brick or concrete surfaces for fixing of tiles in wall etc complete all as specified and directed by Engineer - in - Charge.

M&L rendering 10 mm thick on fair faces of stone masonry surfaces or concrete surfaces on wall in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed .

M & L rendering 20 mm thick in two layers (15mm+5mm) ,on fair faces of stone masonry surfaces or concrete surfaces in cement mortar 1:4 finished even & smooth with out using extra cement including use of water proofing compound in outer layer, complete all as specified and directed. (Note- Water proofing compound use against this item measured and paid seperately )

M & L for rendering 15mm thick, in cement mortar 1:4 on fair faces of stone masonry work or concrete surfaces and finished even and smooth with out using extra cement but with using water proofing compound. Note Water proofing compound to bemeasured and paid separately.

M&L rendering 15 mm thick on stone masonry surfaces in CM 1:6 finished even and smooth without using extra cement.

M&L for preparation of new plaster surface of ceiling and applying 2 coats of oil emulsion distemper or water based distemper over a coat of alkali resistant primming paint including providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plaster surface of wall and applying 2 coats of premium quality oil emulsion distemper or Water base distemper over a coat of alkali resistant priming paint incl 2mm thick wall care putty complete all as specified and make & model as approved by GE

Material & Labour for applying Two or more coatsof 100% Premium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance asper IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified

M&L for preparation of new wood and wood based surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pnik primer.

Preparing of new or previously untreated steel surfaces, over 10cm in width or girth,not otherwise described including washing and cleaning etc., and applying 2 coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of white primer complete all as specified and directed.

M&L dressed porbandar stone masonary walling of squared walling in CM (1:6), brought up to courses, complete all as specified and directed .

S&F powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified.

S&F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers.

M&L for 2nd class hard wood as in plain, solilid straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

S&F 1st class hardwood Small fitting such as brackets of any type,latch and hinge blocks, shaped door and window stops and the like including allnecessary labours, articles not exceeding 200 Cu.cm each complete all as specified and directed.

S & F For Solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face fiixing in frame at site as per specification & drawing

S & F 200 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S & F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed

S&F for 100 size stainless steel butt hinges complete all as specified and directed

Supply & Fixing 150 mm Aluminium handles, cast type, anodised complete all as specified and directed.

S&F Tubular Towel Rail 20mm dia D type 60cm long between flanges of brass chromium plated complete all as specified and as directed.

S&F Vitreous China urinals, half stall, complete including providingand fixing plugs, bedding urinalagainst wall in cement mortar1:2, securing urinal to plugs withand including 60mm long brassscrews, pointing around urinalback in cement; fixing automaticflushing cistern with brackets,flush pipe, grating and Union fordischarge pipe including supply pipe to flushingcistern, trap and waste pipe

S & F Vitreous china wash basin, table top min size 550 x 400 mm including waste pipe waste fitting, brackets and cutting for and pinning in ends of brackets or errecting stand but excluding taps, chain and plug .

S&F Pillar Taps cast copper alloy chromium plated fancy type 15mm bore size of Make Jaquar/Esscco or equivalent complete all as specified.

S&F PVC connection 15 mm size with PTMT nuts or length 450 mm complete all as specified.

S&F bib taps chromium plated, fancy type with crutch or butterfly handle, screwed down for iron pipe, 15mm bore of pipe fixed Complete all as specified and directed.

S&F Vitreous China premium / 1st quality wash down water closet wall hung EWC white / ivory / off white (closed pattern incl all necessary accessories like rag bolts / gel gasket etc. excluding flushing cistern & flush pipe) incl seat cover complete in all respect all as specified

S&F 10 ltr capacity PVC valveless, syphonic action type flushing cistern, low level, whiter with inlet, ball valve, float and handle including brackets, connection to pipes, flush pipe to pedestal pan, including all joints, complete all as directed by Engr-in-charge.

S&F Stop Valve (Angle Valve) 15mm bore size chromium plated fancy type complete all as specified.

M&L PVC (SWR) floor trap, plain with grating including jointing to waste pipe in cement mortar 75mm dia.

S&F of 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring, joints laid in trenches or in floor complete all as specified and directed.

S&F of 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring,laid in trenches complete all as specified and directed.

S&F PVC (SWR) 110/75 mm dia junction single T equal or un equalwith an floor

S&F PVC (SWR) 110mm dia bends in any radius.

S&F of 75mm bore PVC (SWR) vent cowel complete all as specified and directed.

S&F 1000 Ltr capacity, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position, including with lead, locking arrangement, tounge nipple for inlet, outlet connections etc. complete all as directed by Engr-in-Charge.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. 16mm pipe outer dia, Complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. 20mm pipe outer dia, Complete all as specified and directed.

S&F Gun mental globe or gate valves, with iron wheeled head screwed both ends of iron pipes for 25 mm bore pipe fixed Complete all as specified and directed.

S&F ball brass valves 25mm bore,high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

M&L for 10 mm thick (average) screed bed in CM (1:4) in order to maintain proper slope and base over existing roof surfaces for laying of APP based polymeric membrane, finished even and smooth without extra cement complete all as specified and as directed. Note:- Polymeric membrane will be measured and paid separately

M&L for water proofing treatment to RCC roof slab including parapet comprising with the following course of treatment / specification from bottom to top:- (a) Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces. (b) one layer of APP based polymeric membrane of approved manufacturer, 3 mm thick, weight not less than 3.6 Kgs per Sqm, reinforced with non wovwn polyster fabric or weight not less 150 gms per sqm. Polymeric membrane shall be taken to a height of 60 cm 9 minimum) and then inserted insde the groove of parapet wall and shall be finished by a membrane flashing. Note:- (i) Laying of APP based membrane shall be done by torch on method or as per manufacturers instruction. (ii) A minimum overlap of 150 mm and 100 mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as manufacturers instruction. (iii) Applying two coats of Bituminous aluminium paint on top of APP membrane.

S&F Health faucet (ABS chrome plated) with 1 mtr long flexible tube and wall hook complete.

M & L Concrete bed 1:4:8, Type D2 to drain 150mm bore of pipes including packing under,and haunching against the sides of pipes after they are laid and tested.

M & L for 150mm dia reinforced concrete pipes, class NP3, laid and jointed complete with collars laid in trenches and jointed as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Taking down bird proofing net carefully from hanger ceiling up to 10 M high and refixing the same (after painting repairing work of ceiling, painting) fixing with required ties and wire and ropes, complete all as specified and directed. (New mesh if required will be measured and paid seprately).

S&F bird proofing net of 100% virgin Nylon mono filament net made of around +/- 0.80 yarn in 32mm square mesh and having yarn breaking strength appx. 23 Kgs per yarn having ultra violet stabilized for hangar fixed & complete all as per manufacturer's instruction complete all as specified and directed by Engr-in-Charge.

Demolition of concrete of any description and in any position not otherwise specifically provided for cement concrete (unreinforced) complete including removing debries ouside MD land all as specified and directed.

M & L for Sand filling under paver blocks / under floors for cushion complete all as specified and directed.

Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade (with grey cement pigment to match) over sand cushioning Complete all as specified and directed.

All as per above Except Interlocking tiles including filling with sand cushioning ( where ever required ) including levelled with Existing tiled surfaces Complete all as spd and directed by Engineer in Charge. (Note :- Sand and PCC shall be paid and measured Separtely).

M&L machine pressed precast concrete interlocking paver block (coloured) any shape and size conforming to IS 15658-2006 of 80mm thick M-40 grade etc complete (with grey cement and pigment) over sand cushioning.complete all as spd and directed by Engineer in Charge

M&L for Treatment of floor cracks in existing cement concrete pavements by cutting out portion along the cracks with mechanical equipment into 'V' shape of 25mm deep, removing the loose material to a distance exc 250m but n exc 1 Km and cleaning the cut out portion with compressed air to remove all foreign materials like dust, dirt, aggregates etc., priming the proposed pot holes with epoxy resin primer and filling with epoxy resin mortar in repair all as specified and directed by Engineer-in-Charge.

M&L in repair for forming 20mm thick expansion joint (grade'B') filled with HD 100 filler applying bond breaker tape on top of filler board for complete width of joint, provn of closed cell polyethylene back up rod 25mm dia, filled with polyethylene sealant (min depth of sealant above back up rod shall be 12mm) complying with BS-5212, priming the sides and applying masking tape after sealant applied,for thickness of concrete slab 300mm complete all as specified and as shown on drawing.

M&L in repair forming construction Joints (grade 'B') 30mm deep and 10mm wide,(using diamond cutter)and sealed with polyethylne sealant complying with BS-5212 and priming the sides,provn of closed cell polyethylene line back up rod 12mm dia and applying masking tape on edges of joint to prevent accidental spillage of sealant on top surfaces and to give a neat finish to the sealant applied complete all as specified and directed by Engr-in-Charge

M&L in repair forming contraction Joints (dummy joints) (Grade 'B') 65mm deep and 10mm wide,(using diamondcutter)and sealed with polyethylne sealant complying with BS-5212 and priming the sides,provn of closed cell polyethylene line back up rod 12mm dia and applying masking tape on edges of joint to prevent accidental spillage of sealant on top surfaces and to give a neat finish to the sealant applied complete all as specified and directed by Engr-in-Charge

Providing and applying minimum 2.0mm thick road / pavement marking strips (retro reflective) n exc 10cm wide of specified shade/colour using hot thermoplastic material by fully/semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P cleaning the pavement surface of all dirt, seals, oil grease and foreign material etc complete as per direction of Engineer-in-Charge and accordance with applicable specifications.

S&F for PVC coated GI chain link fencing panel jali with 4mm dia GI wire, size 75mm x 75mm of aperture, fitted along all side angle flat iron and fixing with main vertical steel / RCC post of fencing including cutting welding drilling etc complete all as specified and directed. Note : Fencing post, MS flat Iron and foundation concrete, excavation painting etc will be paid seperately

Taking down old point wiring complete for (light, fan, socket 5/15 amps, bell point etc ) complete with all light fittings accessories , such as switches,sockets 5/15 Amps, ceiling roses, pendents, regulators, sockets etc removing materials for taking credit and making good disturbed surfaces of walls, floors, etc all as speified and directed by Engineer -In-Charge.

M & L for point wiring with PVC insulated unsheathed stranded copper conductor cable FRLSH of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm stranded for earth continuity wire, to be drawn in and including, PVC medium grade surface casing capping not less then 20 mm width/in concealed conduit non metallic , rigid PVC conduit of adequated size with all fittings and conduit accessories including suiitable size modular metal flush box and modular white cover plate with frame for housing the switches,socket outlets ,including all necessary wall cutting and making good disturbed surface all as directed and specified. Note : Cutting chases and making good to match with the adjoining surface shall be included in the unit rate.

One light point controlled by one, one way switch

Ditto all as per item No 130.00 but wire 2.5 sqmm One 3 pin 5 amp socket out point on the independent board

Ditto all as per item No 130.00 but wire 2.5 sqmm One3 pin 5 amps socket out let point on same board with other switches.

Ditto all as per item No 130.00 but for one socket outlet 15 amp on independent board with 4.0 Sq. mm cable and 4.0 Sq.mm. earth wire.

Point wiring with PVC insulated unsheathed stranded copper conductor cable FRLSH of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm stranded for earth continuity wire, to be drawn in and including, PVC medium grade surface or concealed in wall with MS sheet metal sunken switch/Terminal box 1.2 mm thick and ebonite switch board cover 3.0 mm thick or PVC moulded switch board and brass screws with cup washers including all necessary wall cutting and making good disturbed surface all as directed and specified. Note : Cutting chases and making good to match with the adjoining surface shall be included in the unit rate.

One light point controlled by one, one way switch

One ceiling /exhaust fan point controlled by one switch and regulator

One 3 pin 5 amp socket out point on the same board with other switches.

One3 pin 5 amps socket out let point on independent board

One bell/buzzer point controlled by one bell push.

One light point controlled by two 2-way switches

All as per same in item No 134.00 above but for one socket outlet 15 amp on independent board with 2.5 Sq. mm cable and 2.5 Sq.mm. earth wire.

All as per same in item No 134.00 above but for one socket outlet 15 amp on independent board with 4.0 Sq. mm cable and 4.0 Sq.mm. earth wire.

S & F Modular switch 2 way 6A with cover plate, 1 module all as specified and directed by EIC.

S & F Modular switch 1 way 6A with cover plate, 1 module all as specified and directed by EIC.

S & F modular socket, Socket, 6A - 2/3 pin combined 2 module with cover plate all as specified and directed by EIC.

S & F modular socket 16A - 2/3 pin combined 2 module with cover plate and box, all as specified and directed by EIC.

S & F Modular switch 1 way 16A, 1 module with cover plate and box all as specified and directed by EIC.

S & F Ceiling rose, surface bakelite 65x50 mm three terminal

S & F Call bell AC-230 Volt single pole ding dong

S & F Bell push, flush type 5 Amps.

S & F Modular bell push 6A, 1 module with cover plate all as specified and directed by EIC.

S& F Electronic Fan regulator 2 module 100/120 Watt step type

S&F LED tube light fittings 1x20 Watt ,220V, AC decorative box type with driver,holder including LED Tube light connecting up with 3 core flexible cppper conductor cable with sutable size from ceiling rose complete all as directed by Engr-In-Charge.

S&F LED tube light fittings mirror type with high output diffuser 2 feet ,1x10 Watt ,220V, AC decorative box type with driver,holder including LED Tube light connecting up with 3 core flexible cppper conductor cable with sutable size from ceiling rose complete all as directed by Engr-In-Charge.

Supply and fixing LED street light fitting 70/72 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr-in-charge.

S & F in replacement LED Next generation, energy saving, environment friendly & robust highbay LED OF 80 Watt with PDC housing suitable for ceiling (Surface/Suspended) mounting with system efficacy upto 150 lm/W including connecting up with 3 core flexible cppper conductor cable with suitable size from ceiling rose and including suitable accesories for mouting chain /bracket complete all as directed by Engr-In-Charge. Make :- Havlells Cat Prat no: SAUCERGENXHBP80WLED757P60DBOLTG/Equivalent in Wipro/Crompton

S & F in replacement LED street light fittings 1x45 Watt , 230V, New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08. including suitable size GI bracket of suitable length and clamps, nut ,bolts etc complete all as directed by Engr-In-Charge. Make:- Havells Cat Part No:- ENDURASUNDOWNSL45WLED765PASYBOPC/equivalent in wipro/bajaj

S & F Decorative light ftting, PVC body , oval in shape & LED lamp suitable for wall fitting including connecting up with 3 core flexible cppper conductor cable with suItable size complete all as directed by Engr-In-Charge.

S & F earth enclosure with 2 pin earth plug sokcet complete with MCB SP 25 amp,flush mounting type LEGRAND/ABB/L&T.

S & F of triple pole and earth enclosure with a three pin and earth plug with sokcet complete with one triple pole MCB 32 Amp.

S & F of MCB TPN 415 Volts, 'C' series, breaking capacity 10 KA of rating 40 to 63Amps

S & F of MCB SP 240 Volts, 'C' series, breaking capacity 10 KA of rating 6-32Amps

S & F in replacement MCB DB made of sheet steel , powder painted with NUTRAL bus bar 200 A, neutral link, IP-43-IK09 protection grade , 415Volts TPN with 4 way Double door

Supply and lay cable 1100 Volts grade LT XLPE insulated PVC sheathed and armoured with stranded aluminium conductor of sizes mentioned below:-

35 Sqmm 4 core

10 Sqmm 4 core

S& F in replacement XLPE insulated armoured and pvc sheated heavy duty electric cable, 4 core 16 Sqmm cross sectional area ,aluminium conductor 1100 volt grade as per IS 7098 (Part-1) 1988 with latest amendment laid in tranches passing through pipes /ducts including testing complete for following size note- rate is inclusive of cable gland & cable lugs Make- Havells/FINOLEX/CCI

S& F in replacement of laying of Double Walled Corrugated (DWC) HDPE pipe of 63/50 mm outer/inner dia size of conforming to IS 16205 Part -24 including necessary bends,coupling ,tees, reducers, spacers,end caps, rubber rings etc having pressure rating not less than 450 N through trenches/wall/floor/on pole in any type of soil for protection of electric cable complete all as directed by Engr-In Charge Make:-ASTRAL TELEREX /eqivalent as approved by GE

S& F in replacement of laying of Double Walled Corrugated (DWC) HDPE pipe of 50/38 mm outer/inner dia size of conforming to IS 16205 Part -24 including necessary bends,coupling ,tees, reducers, spacers,end caps, rubber rings etc having pressure rating not less than 450 N through trenches/wall/floor/on pole in any type of soil for protection of electric cable complete all as directed by Engr-In Charge Make:-ASTRAL TELEREX /eqivalent as approved by GE

S& F laying of Double Walled Corrugated (DWC) HDPE pipe of 40/32 mm outer/inner dia size of conforming to IS 16205 Part -24 including necessary bends,coupling ,tees, reducers, spacers,end caps, rubber rings etc having pressure rating not less than 450 N through trenches/wall/floor/on pole in any type of soil for protection of electric cable complete all as directed by Engr-In Charge Make:-ASTRAL TELEREX /eqivalent as approved by GE

Supply, Installation, Testing and commissioning CPRI approved LT Panel outdoor ype cubical panel board IP 65 free standing floor mounted made out of 3.15 mm thick CRCA sheet, duly powder coated, compartmental design with locking arrangements, weather and vermin proof with proper ventilation slots complete of suitable size and comprising of following items:-

(a) INCOMER

i) MCCB 100 Amps 415V 25 kA 4 pole - 1 No. (Main Incomer)

(b) OUTGOING

(i) MCCB 63 Amps 415V 25 kA 4 pole - 2 Nos.

(ii) MCB 40 Amp 415V TP, 10kA- 2 Nos.

(iii) MCB 16 Amp 215V SP ,10 kA- 4 Nos.

(iv) Onload change over switch 415V in sheet metal enclosure 3 pole 63A - 02 No.

(c) BUS : 150 Apms Copper bus with colour coded heat shrinkable sleeve

(d) METERING & INDICATION

iii) Indication lamps R,Y,B with 3 Nos Of 2A HRC Fuses - 2 Set

f) Internal wiring with suitable size of PVC insulated stranded copper conductor cable duly crimped with copper lugs & ferruled.

S & F of Steel tubular swaged poles swan neck type complete with cast iron base plate, finial taper plug, Cap, mild steel bolts, nuts,screw, etc. type 410 SP-31 (9.0 meters long) erected in vertical position embedded in PCC foundation including painting with two coats of aluminium paint over a coat of primer and synthetic enamelled paint in alternate white and black strips 30cm wide each up to 1.5 Mtr height from top of coping complete all as specified and directed. Note :- Earth work, PCC for foundation and coping shall be measured and paid for separately.

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion

M& L Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with earthing lead of 4mm dia galvanised iron or steel wire all as shown in Plate No. 2 to the earthing test point all as specified and indicated including testing on completion all as specified and indicated including testing on completion

S&F MCCB 4 pole 415 volt, 100 Amp AC 50 Hz, of breaking capacity 16 KA with adjustable thermal and fixed magnetic setting system against over load and short circuit conditions incl neutral adjustment (Ics=100% of Icu) for connecting of LT cable including enclosure box for housing MCCB with all accessories complete all as specified and as directed.

Supply and fix GI tubes medium grade complete with all fittings (misc fitting required on site like; union, tee, bend, elbow, reducer, socket deemed to be included in rate) tobe fixed on wall and ceilings or laid in floors/trenches complete of following bore of pipes:- GI tubes medium grade 25 mm dia

S & F of gate valve, with iron/UPVC wheel head screwed both ends for iron/UPVC pipe of 25 mm bore incl provn of union nipples sockets etc.

S & F of PVC junction box of size inside dimenssion 250x200x100 mm complete with industrial connector, including clamp made out of MS flat iron 30x5 mm , nut, bolts, washer etc , MCB 6-10Amps complete all as specified & directed Make:Sintex cat no : GS JB 2520 and equivalent model of makes specified.

Supply & fix steel tubing GI light grade for cable protection passing under road / floor or for fixing to poles all as specified and as directed of size 50 mm dia along with necessary clamp nut bolt etc complete all as specified and as directed. Make - TATA / JINDAL / SWASTIK

Dismantling unserviceable main switch/ kitkat DBs/ MCB including wooden board from existing position and making good disturbed surfaces of wall to match with existing surfaces

Supply & fix PVC insulated 3 core 1.5 sqmm multistranded Copper conductor cable on pole for security light from junction box to street light fititng including making necessaey hole on surface of pole for insertion of 3 core pvc cable inside the pole upto street light fitting as specified & directed. etc complete all as specified and directed. Make:- Polycab/Havells/Gloster

Vastushilp Building Designer (BID ID -3163978)

AADESH CONSTRUCTION (BID ID -3163309)

OM ENTERPRISE (BID ID -3162958)

M/S Unicon Engineering co (BID ID -3162936)

m/s prakash enterprise (BID ID -3162540)

M/s SK Traders (BID ID -3164254)