CONSTRUCTION OF AYUSHMAN AROGYA MANDIR (AYUSH) AAM-SC AT LAXMIPUR UNDER RD KANCHANPUR SUB DIVISION DURING THE YEAR 2025-26.

2.13 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. -All kinds of soil

2.12 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. -All kinds of soil

2.16 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. -All kinds of soil

2.19 Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete.

4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level: 4.1.15 1:4:8 ( 1 Cement: 4 fine sand : 8 graded well burnt brick aggregate 40 mm nominal size)

4.1.14 1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brick aggregate 40 mm nominal size)

4.4 Centering shuttering including struttings, propping etc. and removal of form work for: 4.4.1 Foundations, footings, bases for columns.

4.17 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

5.1 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- -All work upto plinth level: 5.1.2 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)

5.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement- 5.2.2 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)

5.3 Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement- 5.3.2 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)

5.7 Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 5.7.2 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)

5.19 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 5.19.4 Thermo-Mechanically Treated bars of grade Fe-500D or more

5.18 Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3(1cement : 3 fine sand) etc. complete, excluding the plastering of jambs, sills and soffits 5.18.2 40 mm thick

5.8 Centering shuttering including struttings, propping etc. and removal of form work for: 5.8.1.1 Foundations, footings, bases for columns etc. for mass concrete with timber plank

5.8.4.2 Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply

5.8.5.1 Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply

5.8.6.1 Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply

5.8.12.1 Edges of slabs and breaks in floors and walls under 20 cm. wide

5.8.13 Weather shade, Chajjas, corbels etc., including edges.

6.1 First class brick work in foundation and plinth including cost of all materials as required complete:- 6.1.5 In cement mortar 1:6 ( 1 cement : 6 fine sand ).

6.10 Half brick masonry work with first class bricks in foundation and plinth including cost of all materials as required complete:- 6.10.3 In cement mortar 1:4 ( 1 cement : 4 fine sand ).

6.12 Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- 6.12.3 In cement mortar 1:4 ( 1 cement : 4 fine sand ).

8.46 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. 8.46.2 Fixed to openings /wooden frames with rawl plugs screws etc.

8.51 Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size)

8.94 Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 8.94.1 300x16 mm

8.95 Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 8.95.1 300x10 mm

8.98 Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 8.98.1 125 mm

8.99 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 8.99.1 Single rubber stopper

8.120 Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws.

8.121 Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solvent adhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’s specifications and directions of the Engineer-in-charge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter).

9.3 Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required.

9.13 Providing and fixing fan clamp type-I of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs during laying including painting the exposed portion of loop, all as per standard design complete.

9.22 Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

9.5 Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, & with cleats with bolts & nuts, rivets, locking arrangement, handles, hooks & eyes, pinlets including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required:- 9.5.1 Using M.S. angels 40x40x6 mm for diagonal braces.

16.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :- 16.1.1 For fixed portion of approved quality:- 16.1.1.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

16.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):- 16.1.2.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

16.3 Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :- 16.3.1 With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm )

16.2 Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board grade-I, type II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows, shutters and partition frames with C.P. brass / stainless steel screws all complete as per architectural drawing and the direction of Engineer-in-charge :- 16.2.1 Prelaminated particle board of approved quality with decorative lamination on one side and balancing lamination on other side.

16.10 Providing and fixing stainless steel ( SS 304 grade ) adjustable friction window stay of approved quality with necessary stainless steel screws etc. to the side hung windows etc. complete as per direction of Engineer-incharge:- 16.10.1 205 x 19 mm

11.55 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg/cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc. complete as per direction of Engineer-in-charge : 11.55.2 Single socketed pipe - 110 mm OD

10.9 Providing and laying cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded well burnt brick aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips etc. all complete as per direction of Engineer-in-charge. 10.9.2 40 mm thick with 20 mm well burnt brick aggregate

10.40 Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-incharge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge. 10.40.2 600 mm X 300 mm in all shades and design

10.54 Providing and fixing Precast chequered cement concrete tiles 18 mm thick, laid in footpath & courtyard, on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry including rubbing and cleaning etc. all complete as per direction of Engineer-in-charge. 10.54.1 In dark shade using ordinary cement

10.41 Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge. 10.41.1 Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles 10.41.1.1 300 mm x 300 mm in all shades and designs

10.42 Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge.. 10.42.2 Double charged Stainfree vitrified tiles (Glossy) 10.42.2.1 Size of tile 600 mm x 600 mm

12.1 12 mm cement plaster of mix 12.1.4 Cement mortar 1:6 (1 cement : 6 fine sand)

12.1 12 mm cement plaster of mix 12.1.2 Cement mortar 1:4 (1 cement : 4 fine sand)

12.9 6 mm cement plaster of mix : 12.9.1 Cement mortar 1:3 (1 cement : 3 fine sand)

12.10 Neat cement punning.

12.35 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : 12.35.1 New work ( two or more coats) over and including water thinnable priming coat with cement primer.

12.19 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

12.42 Finishing walls with premium acrylic smooth exterior paint with Silicon additives of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : 12.42.1 New work ( two or more coats applied @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

12.60 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: 12.60.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approved brand and manufacture

18.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : 18.1.2 Stainless Steel AISI-304(18/8) Orissa pattern W.C pan of size 585x480 mm with flush pipe and integratedf type of foot rests.

18.3 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 18.3.1 W.C. pan with ISI marked white solid plastic seat and lid.

18.7 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : 18.7.1 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

18.8 Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

18.10 Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: 18.10.1 Kitchen sink with drain board 18.10.1.1 510x1040 mm bowl depth 250mm.

18.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 18.28.2 Flexible pipe 18.28.2.1 32 mm dia

18.83 Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 6 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: 18.83.1 Single socketed pipe - 110 mm OD

18.32 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 18.32.4 Rectangular shape 1500x450 mm

18.33 Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

18.73 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. 18.73.2 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms.

18.84 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: 18.84.1 Coupler 18.84.1.2 110 mm

18.84.3 Single equal tee without door 18.84.3.2 110x110x110mm

18.84.4 Single equal tee with door 18.84.4.2 110x110x110mm

18.84.5 Bend 87.5° 18.84.5.2 110mm

18.84.6 Plain shoe 18.84.6.2 110mm

18.87 Providing and fixing to the inlet mouth of soil, waste & vent pipes pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete. 18.87.2 100mm

18.85 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC soil, waste & vent pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. 18.85.2 110mm

19.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 19.7.3 25 mm nominal outer dia .Pipes.

19.7.4 32 mm nominal outer dia .Pipes.

19.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 19.8.1 15 mm nominal outer dia .Pipes.

19.8.2 20 mm nominal outer dia .Pipes.

19.78 Making chases upto 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.

19.46 Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete as per CPWD specification and direction of the Engineer - in - charge.(New work) 19.46.2 20 mm nominal bore

19.46.3 25 mm nominal bore

19.46.4 32 mm nominal bore

19.46.5 40 mm nominal bore

19.46.6 50 mm nominal bore

19.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work 19.9.5 40 mm nominal outer dia .Pipes.

19.9.6 50 mm nominal outer dia .Pipes.

19.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 19.17.2 32 mm nominal bore

19.18 Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete : 19.18.3 25 mm nominal bore

19.19 Providing and fixing gun metal non-return valve of approved quality (screwed end): 19.19.2 32 mm nominal bore 19.19.2.2 Vertical

19.21 Providing and fixing uplasticised PVC connection pipe with brass unions : 19.21.2 45 cm length 19.21.2.1 15 mm nominal bore

19.51 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 19.51.1 15mm nominal bore.

19.58 Providing and fixing PTMT grating of approved quality and colour. 19.58.1 Circular type. 19.58.1.1 100 mm nominal dia.

19.76 Cutting holes upto 30x30 cm in walls including making good the same : 19.76.1 With 1st class bricks.

19.77 Cutting holes upto 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof.

19.52 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 19.52.1 15 mm nominal bore.

19.65 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms.

19.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and painting communication graphics (Maternal health, Immunisation, Yoga, Tele consultation, Drug distribution & Health awareness) about Health and Wellness center with approved color on the façade with circle. Size of inner circle with pattern design will be as per standard ratio & as per direction of the Engineer-in-Charge (APPROVED RATE)

Providing and painting local craft pattern which encircles the windows, doors, ventilators, canopy, parapet and any projected portion of building with approved colors. The sizes of the pattern will be as per standard ratio & as per the direction of the Engineer-in-Charge (APPROVED RATE).

Charges for drilling and boring of pilot hole in any soil strata by water jet or any suitable method including collection of samples at various suitable levels and preservation of samples in polythene bags / sample boxes and disposal of excess soil or mud and maintain the pilot hole properly and required staging as per specification ( IS : 2800 ) and direction of the Engineer-in-charge. A. upto 100 metre depth ii. 50 mm dia

Providing and fitting fixing of Bottom Cap ( UPVC ) as per specification and direction of the Engineer-in-charge. i. 40 mm

Providing, fitting, fixing, and lowering UPVC ribbed screen pipes as per IS:12818 for Mark II / III / OHP as per specification and direction of the Engineer-in-charge. iii. 40 mm NB

Charges for fitting, fixing, and lowering UPVC 'CM" casing pipe as per IS:12818 for Mark II / III / OHP as per specification and direction of the Engineer-in-charge. iii. 40 mm NB

Providing and fitting fixing G.I. pipe (medium class) conforming to IS : 1239 for OHP of approved quality as per specification and direction of the Engineer-in-charge. i. 40 mm dia

Providing and fitting fixing Shallow well hand pump (C.I.) No.6 (90 mm) as per IS:8035/1999 complete set as per

Charges for development of ordinary hand tube well by pumping out the turbid water till clean sand free water is obtained as per chapter-20 of CPWD specification and direction of the Engineer-in-charge.

Providing and fixing G.I. socket as per CPWD specification and direction of the Engineer - in - charge. v. 40 mm dia

Providing and fixing 1 HP single phase monoblock pump set ( Pump & Motor) ISI marked and approved quality (KIRLOSKAR) or equivalent with necessary connections with delivery and suction line complete as per the direction of the Engineer-in-Charge. (Cost of electrical accessories and connection etc. to be paid separately).

Please Enable Macros to View BoQ information