110/EDCB/2022-23

Amount

Dismentaling of earthing, jumpering and cable box from 5 MVA Transformer at 33/11 KV S/s Nawabganj Town under EDD-I, Bareilly

Shifting of 5 MVA Transformer from the plinth to switchyard by crain distance 15 mtr.

The work of safe carriage of the following material from CB Ganj store center to work site under the jurisdiction of EDD-II, Bareilly. Approx. distance upto 45 Km. Including safe loading and unloading.

ST Pole 11 Mtr

11 KV Incoming Panel (VCB)

11 KV Outgoing Panel (VCB)

11 KV XLPE Cable 3x185 Sq mm

11 KV 3x120 Sqmm XPLE Cable

LT XLPE Cable 1x240 Sqmm

Indoor & outdoor Cable Jointing Kit Suitable for 11 KV 3x120 Sqmm XPLE Cable

Outdoor Cable Box for 11 KV XLPE Cable 3x185 Sq mm

Straight Through Cable Jointing Kits for 11 KV XLPE Cable 3x185 sqmm

ACSR Raabbit Conductor

ACSR Dog Conductor

ACSR Weasal Conductor

11/0.4 KV 3 Phase 30 KVA T/F

11 KV Pilfer proof Metering cubical and CT PT Unit

Other Line material i.e., 33 KV & 11 KV pin insulater/stay/earthing complete/Disc Fitting/Disc Insulators/Dropper Channel/Crossing Bracing/ Top Channel/Binding Wire/Danger Board/Barbed Wire/numberplate/stone pad/Control Cable etc

Construction of T/F plinth 1.5x1.5x2 m3 for mounting 630 KVA T/F including foundation work (below ground 0.5 M), Brick work, RCC slab of 4” thickness and plastering in 1:6 ratio with 02 Nos channel pieces of 1.5 mtr long of size 100x50x6 mm compete in all respect

Cage fencing of 630 KVA Plinth mounted transformer in Town areas to avoid electrical human/cattle accidents by fabrication of cage (1 Inch Sq wiremesh) made of 10 No gauge in suitable size angle iron frame of size 7.5'(L)x5'(W)x8’(H) by strenghtening of wire mesh 20x3 mm M.S. flat haorizentally as well as vertically, Grouting the panel with 1:2:4 cement/coorse send/brick ballast. The Frame should be bolted on angles at the four corners so that frame may be un-bolted/bolted at the time of replacement of the transformer. Provision of 1 gate should be there for maintenance of the transformer. Painting (1 coat of red oxide + 2 coat of Bus green enamel paint). The wire mesh should be earthed with 50x6 mm MS earthing strip with existing earthing of Transformer Body. All men, material and T&P provided by the contractor to complete the fabrication, transportation and installation.

Mounting of 630 KVA T/F Transformers as per norms complete in all respect -

Erection/Installation of following new panel (VCB) in control room including grouting of Anchor bolt of Panel and making/repairing of pocket for cable to insert in panel from trench and fixing, taping of bus bar with wiring for PT. AC, DC connection including providing of AC & DC Supply.

11 KV Incoming Panel (VCB)

11 KV Outgoing Panel (VCB)

Providing cutting, fixing and welding of MS Strip from existing, earthing to new 11 KV VCB Complete in all respect, all material shall be arranged by the Contractor.

Pipe Earthing of VCB & Transformer (By boring of 4 inch diameter 20 m deep, 40 mm diameter A class GI pipe is inserted to a depth of 20 m and a holed pipe of 1.5 m length is inserted at the bottom. Tighten one end of the MS strip of size 50x6mm with the nut bolt with the neutral of the converter and weld the other end with the GI pipe inserted in the boring for earthing. Putting a socket on the upper part of the pipe (mouth) so that water can be poured into it to retain moisture. To complete the work Contractor will provide all material, Manpower, T&P, safe carriage of material to worksite. Above work will be carried out under supervision of concerned JE/SDO/EE)

Earthing of Indoor Equipment complete in all respect

Supply and Installation of Battery Charger 24 Volt with Battery Set 24 Volts complete in all respect (Exide Make Only)

Erection of Single/Double pole in H.T/L.T lines including fitting of all accessories as per RESSPO Norms

ST Pole 11 Mtr long (Single)

ST Pole 11 Mtr long (Double)

Grouting of following Pole with 1:4:8 mixture in size(450x450x1500mm.) including cost of cement/BB & sand Required as per RESSPO Norms

ST Pole 11 Mtr long (Single)

ST Pole 11 Mtr long (Double)

The work of Driving the earthing electrode and making connections with 6 S.W.G. GI wire as per RESSPO Norms

Laying, Stringing & Sagging of Following Conductor complete in all respect

ACSR Rabbit Conductor

ACSR Dog Conductor

ACSR Weasal Conductor

Laying of LT XLPE Cable 1x240 sqmm complete in all respect

Under ground laying of 11 KV XLPE 3x185 sq mm cable in Single circuit complete in all respect Along with road restoration

Under ground laying of 11 KV XLPE 3x120 sq mm cable in Single circuit from Power T/F to VCB to D.P in Power House) complete in all respect

Hoisting of 11 KV XLPE Cable (3x185 Sqmm) on double pole bote with GI pipe of size 6" dia 4 Mtr long including the jumpering complete with clamps , nut and bolts

Supply & Laying of 6" dia G Pipe at various places i.e road crossing & Hoisting etc. complete in all respect ((ISO certified GI pipe 150 NB 3 mm thick dia 6" would be Provided by contractor through approved vendors of Discom at his own cost)

Fixing of Outdoor11 KV Cable Boxes for 3x185 sqmm XLPE Cable complete in all respect

Fixing of 11 KV Straigh through Jointing Kits for 3x185 sqmm XLPE Cable complete in all respect

The work of digging of pits, erection of Stay Clamp, Insulator etc.

Grouting of stays, 1:4:8 cc ratio (600x600x300mm.) as per RESPO norms.

Guarding at road crossing complete in all respect

Supply and Fixing of Following Material as per RESPO norms complete in all respect (would be Provided by contractor through approved vendors of Discom at his own cost)

Stone Pad 300x300x75 mm

X-Arm M.S. Angle 65x65x6 mm V-Type

Cross Arm Holding Clamp

11 KV Pin Insulator

11 KV Pin with Nut

F Bracket

Aluminium Tape

Aluminium Binding Wire

Jointing Sleev For ACSR Rabbit

Danger Board With Clamp

Barbed Wire

Number Plate

G.I Holding Clamp for G.I. Pipe

Nut Bolt With Washer

Top Channel 100x50x2240mm 9.6 KG/Mtr

M.S. Channel 100x50x2028mm @ 9.6 KG/Mtr for Dropper Channel

M.S. Angle Iorn 65x65x6 (2700 mm)

M.S. Angle 75x75x6x2028 mm

Aluminium Lug 240 sqmm with Nut&Bolt

Dropper Channel

Holding Clamp for Top Channel, TPMO & Fuse Set etc With Nut & bolts

Top Channel

11 KV TPMO

M.S. T-Off Channel

Clamp With Bolt & Nut

Cross Bracings M.S. Angle

11 KV Disc Insulator B&S Type

11 KV Disc Insulator

11 KV Disc Fittings

PG Clamp

Dropper Channel (100x50x2000 mm)

Clamp With Nut & Bolt

Gaurding Angle 65x65x1.6 mtr long

Clamp for Gaurding Angle

G.I. Wire 6 SWG & 10 SWG for Gaurding & Lacing

After Mounting of CT PT unit on double pole, laying of 50 Mtr 11 KV 3cx120 sq mm cable in single circuit on river sand form Double Pole to metering room complete in all respect. Alongwith filling of cable jointing kits

Installation of 11 KV Pilfer Proof Metering Cubicle in metering room complete in all respect

Cutting of Tree Branches

M/s Shubham Traders