Routine Day to Day Mtce. for a period of Four months for BSNL staff colony at Ghodacamp, Shahibaug, Ahmedabad City, Ahmedabad.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

Second class teak wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing.

30 mm thick plain PVC door shutters

Providing and fixing Stainless steel Aldrop of approved quality with screws etc. complete :

Providing and fixing Stainless steel Tower bolt of approved quality with screws etc. complete :

Providing and fixing Stainless steel round latches of approved quality with screws etc. complete :

Providing and fixing stainless steel handle with necessary screws etc. complete.

Providing and fixing stainless steel hanging floor door stopper with necessary screws etc. complete.

Single rubber stopper

Providing and fixing 35 mm wooden cup board or wardrobe knob of approved quality with necessary screws as per the direction of Engineer in charge.

Providing and fixing 25mm dia. SS curtain rods with SS brackets fixed with screws and PVC sleeves etc. wherever necessary complete as per the direction of Engineer in charge.

Repalcing existing damaged wire gauge in doors & windows shutter by Providing and fixing fly proof galvanized SS 304 wire gauge using wire gauge with average width of aperture 16x18mm with wire of dia 0.22 mm of approved quality with screws and existing available 12 mm mild steel U beading etc. all complete as per the direction of the Engineer-in-charge. (The clear inside area of panel shall be measured for payment. The rate includes of all above operations nothing extra shall be paid. The cost of MS beading shall be paid for separately if required.)

Repalcing existing damaged wire gauge in doors & windows shutter by Providing and fixing fly proof galvanized SS 304 wire gauge using wire gauge with average width of aperture 16x18mm with wire of dia 0.22 mm of approved quality with nails, & second class teak wooden beading wherever required etc. all complete as per the direction of the Engineer-in-charge.( The clear inside area of panel shall be measured for payment. The rate includes of all above operations nothing extra shall be paid. )

Reparing of pelmet and fixing to wall by screws, clamps wherever required etc. all complete as directed by Enginner-in-charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.

G.I. pipes

Repairing of MS steel windows/windows grill with or without taking out fixed/openable shutter/grill and getting repair at any floor level by welding of grill/ M. S. butt hinges /holdfast/straightening/ cutting of members and other required arrangment for proper functioning of window etc and fixing in position as directed by engineer-in-charge. ( The item includes cost of all opearations and MS hingesof any type, labours and tools and plant etc. but excluding cost of scaffolding and glass panes which shall be paid for seperately in relevant item.)

Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc. complete.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. The item excludes cost of scaffolding which shall beincluded in relevant item of scaffolding for maintenance work.

Coupler

110 mm diameter

110 mm diameter

Shoe (Plain)

110 mm diameter

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

12 mm cement plaster of mix :

1:6 (1 cement : 6 coarse sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:6 (1 cement : 6 coarse sand)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour :

New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. meters and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50metres lead.

With cement mortar 1:4 (1cement: 4 coarse sand).

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty:

Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Renewal of old putty of glass panes (length)

Providing & fixing White vitreous china water closet squatting pan (Indian type) along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge.

Orissa pattern W.C Pan of size 580x440 mm

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge.

Dismantling 15 to 40 mm dia G.I. pipe with fittings including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer in-Charge.

Internal Work- Exposed on wall

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Fixing of loose Aldrop, Stopper, Latch, handle etc. fixed to door/window shutter with necessary screws, rawl plugs, Bolts & Nuts etc. as required, all complete as per the direction of the Engineer-in-charge.

Deduct for providing 3mm thick Bajari glass panes instead of ordinary float glass panes weighing 4 mm thick in steel glazed doors, windows and clerestory windows shutters and ventilations.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area 3 sq. metres and below

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :

Of area 3 sq. metres and below

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles 10 mm to 25 mm

Dismantling C.I. or asbestos or PVC rain water pipe/drainage pipes with fittings and clamps including stacking the material within 50 metres lead :

75 to 80 mm dia pipe

100 mm dia pipe

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :

15 mm to 40 mm nominal bore

Taking out C.I. cover with frame from R.C.C. top slab of manholes of various sizes including demolishing of R.C.C. work manually/ by mechanical means and stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead as per direction of Engineer-in-charge.

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Disposal of building rubbish/ malba/ similar unserviceable dismantled or waste materials by mechanical means including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all loads including all lifts involved.

Deduction for taking over of unserviceable materials obtained from dismantling/ demolishing as is where is basis. Note : Materials shall be taken over by the contractor at his own cost and will allow to deduct at the quoted rate from the bill of payment.

C.I./S.C.I. pipe & fittings, C.I. cover, CI Nahni trap, etc.

Structural Steel members like Tee, angle, flats, square bars, Channels, Rolling shutter, G.I. pipes, profile frame, etc.

Brass/ CP brass pillar cock, stop cock, Bib cock, Gate valve, Flush cock, etc.

PVC Flushing cistern - 10 Litres capacity

PTMT/PVC Bib cock, stop cock, Pillar cock, etc.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

10 litre capacity - White

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete :

White solid plastic seat with lid

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings :

Flat back wash basin of size 550x400 mm.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe

32 mm dia

40 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 453x357 mm

Providing and fixing C.P. brass health Faucet with flexible tube upto 1 metre long with hook to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

15 mm nominal dia

Providing and fixing C.P. brass Coupling for wash basin and sink, of approved quality as per the direction of Engineer in charge.

32mm dia.

40mm dia.

Providing and fixing PVC Nahni trap of self cleansing design of approved make including cost of cutting and making good the walls and floors etc. complete as per the direction of Engineer in charge.

110 mm inlet and 75 mm outlet

Providing and fixing on wall face unplasticised Rigid PVC single socketed drain pipes conforming to IS : 13592 , Type-B of approved quality & manufacture including jointing etc. all complete as per the direction of Engineer-in-charge. The item excludes cost of scaffolding which shall be inclusive in relevant item of scaffolding for maintenance work.

110mm diameter

90mm diameter

Providing and fixing on wall face unplasticised Rigid PVC moulded fittings/acessories for unplasticised Rigid PVC drain pipes conforming to IS : 13592 , Type-B of approved quality & manufacture including jointing etc. all complete as per the direction of Engineer-in-charge. The item includes the cost of connecting PVC drainage pipe with existing cast iron NT, Pipe or P trap of WC with cement, Mseal, solutions, etc. all complete.

Tee with access door

Single Y without access door

Bend 87.5° with access door

Coupler

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Dismantling holes up to 30x30 cm and up to depth of 150mm for clearing the SCI pipe drainage pipe alround embedded in wall so that the new PVC drainage line fittings can be jointed with the existing SCI pipe and plug in the holes with cement mortar 1:4 and making good the same after the fixing of new PVC pipe fittings with existing SCI drainage pipe etc. complete as per the direction of Engineer in charge.

For SCI pipe up to 100mm dia.

Providing and fixing PVC pipes including all PVC fittings, including fixing the pipe with clamps at 1.0m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

50 mm outer dia. Pipe

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length

15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

100 mm diameter

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:

15mm nominal bore

Providing and fixing C.P. brass stop cock/angle cock/ concealed cock of standard design and of approved make conforming to IS:8931.

15mm nominal bore

Proiving and fixing C.P. brass Pillar cock for wash basin of approved make & quality confirming to IS and manufacturer's specifications etc all complete as per direction of Engineer in charge.

15mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

60 cm length

15 mm nominal bore

Providing and fixing UPVC (Schedule 80) pipes, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

Internal work - Exposed on wall

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

Providing and fixing S.S. grating of approved quality for Floor Trap including dismantling of existing jali wherever required etc. complete as per the direction of Engineer in charge.

Replacement of 25mm nominal bore C.P brass flush cock of standard design and of existing available make or approved equivalent in existing concealed G.I. line including replacement of existing G.I. pipe fittings wherever required and making good the walls with white cment etc. complete as per the direction of Engineer in charge.

Repairs to leakage/unserviceability of 15mm nominal bore C.P. brass/Brass bib / stop cock/pillar cock, brass urinal spreader, shower, flush tank etc. fixed in existing G.I. pipe line by necessary replacing rubber washer or with Taphlon tap or cleaning with acid as required etc. all complete including dismantling the same whereverrequired as per the direction of Engineer-in-charge. The item includes labour charges along with cost of providing necessary rubber washer for bib cock/stop cock/Flush tank, taphlon tap, acid required to repair the leakage/unserviceability.

Replacement of existing Gun metal wheel valve/ brass handle valve and necessary G. I. pipes and fitting with Brass handle valve (screwed end) of approved make and quality including necessary G.I. pipe and fittings of required length in existing G.I. pipe line etc. complete as per the direction of Engineer in charge.

25 mm nominal bore.

32 mm nominal bore.

Providing and fixing temporary wooden scaffolding made from bamboo and ballies up to any floor level for repairing work on building face. Maintaining it in a serviceable condition for the required duration and removing it after completion of repairing work etc. all complete as per the direction of Engineer-in-charge. The elevation area of the scaffolding shall be measured for the payment purpose. Scaffolding material shall be property of contractor after removal.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality

Rectangular shape 600x450 mm internal dimensions

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :

For pipes 100 to 250 mm diameter

Supplying and fixing Precast RCC cover 300x300 mm with frame for gully trap (standard pattern) including dismantling of existing gully trap cover with frame wherever required etc. complete as per the direction of Engineer in charge.

Cleaning of manholes, Gully Traps, floor Traps, etc. including connected sewer/sludge lines by rodding, passing Bamboo strips, a jute ball etc. and flowing clean water etc. to ensure proper flow through lines to the satisfaction of Engineer in charge. The rate includes the cost of all tools, plants and labour involved in above operations including disposal of garbage to approved dumping ground and also safety measures of labourers are to be taken by agency during execution of work. The payment shall be paid on Nos. of manholes, Gully Traps, Floor Traps, etc. cleaned.

Manhole up to 1.5m deep.

Gully Trap

Floor Trap/Nahni Trap

Providing IInd class Plumber / IInd class Carpenter / IInd class Mason for attending maintenance works which is not covered in main related Basic items etc. complete as directed by Enginner-in-charge.

Providing Beldar / Coolie / Helper for attending maintenance works which is not covered in main related Basic items etc. complete as directed by Enginner-in-charge.

Repairs to leakage of 15mm dia. G.I. water supply line by replacement of rusted 15mm dia. G.I. Elbow/15mm dia. G.I. Coupling/G.I. Nipple up to 150mm long and making good the walls after repairing etc. complete as per the direction of Engineer in charge. The item includes necessary materials, labours, scaffolding, Tool & plants etc. to complete the Job.

Uprooting trees from the wall, roof and all parts of the building by using scaffolding (from floor one to floor five) and then putting acid and cleaning the dust, dirt and disposing the garbage beyond the municipality area limits and making good the surface with cement concrete / cement mortar etc. complete as per the direction of Engineer-in-charge. The rate shall be inclusive of material costs, labour charges, carriage/ transportation, tools and plants, equipments and incidentals all complete and nothing extra shall be paid on any account unless otherwise specifically mentioned in the item.