ADDN / ALTN AND SPECIAL REPAIRS TO CERTAIN BUILDINGS OF MT POOL AT INS VALSURA, JAMNAGAR.

Amount

SCHEDULE 'A' B/R WORKS

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in hard/ dense soil all as specified and as directed.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in soft/loose soil all as specified and as directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified and as directed.

Removing Excavated soil exceeding 200 m but not exceeding 250 Mtr and depositing where directed at a level not exceeding 1.5 M above the starting point all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils all as specified and as directed.

M & L 150 mm dia Reinforced concrete pipes class NP2 with collars laid in trenches and jointed as specified all as specified and as directed.

M & L for PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150mm bore all as specified and as directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins,arches, pillars etc.but excluding ashlar facings, dressed stonework and precast concrete articles all as specified and as directed.

Precast cement concrete block masonry with solid blocks (1:3:6) type C4 as per IS -2185 (Part I)2005 using 20mm graded stone aggregate,exc 10 cm in width and setting in CM 1:6 complete all as specified and as directed .

M&L for rendering 15 mm thick on Brick masonry surfaces on fair faces of brick work in cement mortar 1:6 with finished smooth and even without using extra cement (Internal)all as specified and as directed.

M&L for rendering 15 mm thick(on RCC roof and vertical surfaces) in cement mortar 1:4 finished smooth and even without using extra cement complete all as specified and as directed.

M & for Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded granite stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating,all as specified and as directed

Extra for forming fair finished drain or channel 30cm inner girth in concrete using extra cement including forms, moulds, mitred/stopped ends etc. all as specified and as directed.

Providing Precast reinforced cement concrete 1:2:4, type B1 (Using 20 mm graded granite stone aggregate) in landings, kitchen shelves, manhole cover etc. and similar articles with plain faces and set in cement mortar 1:4 all as specified and as directed

CRS/HCRM/CRM TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for slabs, chajjas, staircase etc complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for purlins etc complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but n exc 4 sqm each complete all a specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) etc complete all as specified and directed.

Removing building materials etc. (other than spoil payable under item Nos.5,6 &7 in BOQ) to a distance of 500m beyond the lead included in the rates, including loading, unloading and stacking at the destination etc complete all as specified and directed

Site Clearance on complete work site etc complete all as specified and directed.

Dismantling post or struts (wood, steel or RCC) any section, including taking out embedded portion in concrete and making good the disturbed ground complete all as specified and as directed.

M&L for Plain Cement Concrete Type B1, 1:2:4 (using 20mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed .

S & F in repairs Galvanized, 2 strand, steel barbed wire 2.24 mm dia., barbed with 2 mm dia., barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanized mild steel pins etc., including taking down the existing wire complete all as specified and directed.

M&L preparation of steel and steel base surfaces over 10 CM width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed

S&F Mild steel work in posts and struts in fencing and FI fiilets for securing fencing cut to shape as directed, including all necessary drilling, bolting or riveting etc , and similar work confirming to Fe 290 GdeE-165 all as specified and directed

M&L 100mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base complete all as specified and driected.

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 Grade with grey cement and pigment complete all as specified and directed.

M&L for Sand filling under floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering complete all as specified and directed.

M&L providing 100 mm thick PCC 1:2:4 type B-1 usig 20 mm graded aggregate lay in bays finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

Forming Construction joints 30mm deep x 10mm wide filled with sealing compound Grade A complete all as specified and directed.

Rounding to edges of stone slabs one edge,such as in steps cooking platform and other similar situations complete all as specified and directed.

S&F powder coated anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. (Minimum thicknesss of powder coating 50 micron)complete all as specifid and directed.

S&F powder coated anodised aluminium ventilator louver type including all fitting all as required including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc(Thickness or powder coating not less than 50 micron)complete all as specified and directed.

S&F powder coated anodised aluminium window shutters for glazed and gauze, fixed / sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc with powder coating of any colour (Thickness or powder coating not less than 50 micron) . complete all as specified and directed.

S&F powder coated aluminium anodised DECO grill 10mm thick DG 104 not less than 3.97Kg/Sqm fixed with necessary H/F/H channel etc complete all as specified and directed.(DECO grill to be fixed to windows with all fittings as directed by Engr-in-charge)

S&F solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, complete all as specified and directed.

S & F Granite 18-20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified and directed.

M&L 15 mm thick screed bed or bedding layer in cement mortar 1:4,for laying floor finishes all as specified and directed.

M & L Fair finished flat formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off thepremises etc complete all as specified and directed

Taking down chowkhats with shutters (Without taking off shutters from the frames) not exceeding 1.5 Sqm each etc complete all as specified and directed

Taking down shutters of any description exc 1 sqm but n. exc 2 sqm each etc complete all as specified and directed

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water,etc complete all as specified and directed

Dismantling of Cast Iron or reinforced concrete drain pipes of 100mm dia, jointed in cement mortar and taking out of trenches etc complete all as specified and directed

Demolition & breaking up of AC/reinforced concrete Pipe any bore set in cement mortar etc complete all as specified and directed

Dismantling water tanks (PVC) exceeding 250 ltr and not exceeding 500 ltrs capacity etc complete all as specified and directed .

Dismantling Asbestos cement sheets (corrugated,semi corrugated etc) sheets in roof coverings etc complete all as specified and directed

S&F 0.50 mm BMT pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour ,tensile strength of 550Mpa as in roof covering and cladding to wall etc fixed with self tapping screws etc complete all as specified and directed

S&F 0.50 mm BMT Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet of any colour having tensile strength of 550 Mpa as in rigde, gutter etc, fixed with self tapping screws etc complete all as specified and directed

Complete removal of old existing treatment of any thickness from RCC roof by stripping out old tar felt over roofs, parapets, chimney stacks etc as laid horizontally or vertically including taking out layer of cement plaster and PCC of any thickness over RCC roof surface if any completely by scrapping/scrubbing/brooming down etc and cleaning the surface etc complete all as specified and directed

M&L for PCC 1:2:4, type B0 using 12.5 mm graded stone aggregatee as padding concrete to the roof slab complete all as specified and directed

M&L for provision of water proofing treatment by applying oil bound bituminous primer 0.20 kg/sqm, providing and laying 4mm thk APP modified water proofing membrane weighing not less than 4 kg/sqm, reinforced with non-woven polyster matt weighing not less than 160 g/sqm, having softening point not less than 1400 C longitudinal tensile strength not less than 650 N/Sqcm tearing strength of 180 N by torque application including minimum 10 cm side overlap and 15 cm end overlap and applying a coat of blown grade hot bitumen 85/25 over the membrane @ 1.2 kg/sqm finishing the surface with solar reflective bituminous aluminium paint @ 100 g/sqm, complete as per manufacturer's instructions etc complete all as specified and directed

M&L for 25mm thick, PCC 1:2:4 Type B-0 , using 12.5 mm graded crushed stone aggregate for leveling the undulation of floor after dismantling etc complete all as specified and directed

M&L for light shade vitrified ceramic tiles 10mm thick (Square/Rectangular) polished, area of each tiles exceeding 0.42 Sqm but not exceeding 1.00 Sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed

Ditto as above item No 57 but fixed in wall dado/skirting etc complete all as specified and directed

M&Lfor joint free coloured Ceramic tiles of 7 to 8mm thick area of each tile exc 0.18 sqm but n exc 0.38 sqm in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed

Ditto as above item No.59 but fixed in wall dado/skirting etc complete all as specified and directed

M&L 20 to 25 mm thick polished Machine cut Kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed

M&L 20 to 25 mm thick polished Machine cut Kota stone slab as in skirting laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed

M & L for non skid joint free ceramic coloured tiles 7 to 8mm thick Square/ rectangular) area of each tile exc 0.11 sqm but n exc 0.18sqm, in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles complete all as specified and directed

M & L for Glazed ceramic coloured tiles in vertical surfaces size 600x 300 x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as directed and specified by Engr-in-Charge.

M & L 10 mm thick rendering in CM 1:3 on brick or concrete surfaces for fixing of tiles as in dado/skirtings etc complete all as specified and directed

M&L 10 mm thick screed bed or bedding layer in cement mortar 1:4,for laying floor finishes etc complete all as specified and directed

S&F steel rolling shutters of 1.25 mm thickness of laths without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete: push pull or manual type etc complete all as specified and directed

S & F safety lever locks mild steel with 4 levers for rolling shutter etc complete all as specified and directed

S & F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints etc complete all as specified and directed

S & F 35 mm thick Second class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed

S & F 35 mm thick Second class hard wood Plain glazed and skeleton shutter,open rebated and prepared to receive glass,gauze etc,divided in to squares with plain,chamfered or rounded mitred and rebated sash bars any numbers,edges of framing plain,chamfered each complete all as specified and directed.

S&F providing cement concrete in type C1 1:3:6 for fixing holdfast complete all as specified and directed

S&F Mild steel holdfast conforming to Fe 290 Gde-E-165 complete all as specified and directed

S & F 3 mm thick Figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane etc complete all as specified and directed

S & F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty/wooden beads in squares exceeding 0.5 Sqm in each pane complete all as specified and directed

S & F of Fiber glass reinforcement plastic (FRP) door frames of three legged of cross section 90mm x45mm having single rebate 32x15 mm to receive shutter of 30mm thickness . The laminated door frame moulded with fire retardent grade unsaturated polyster resin & chopped mat door frame laminate of 2mm thick filled suitable wooden block in all three legs. This shall be covered with fiber glass from all side mild steel stay shall be provided at the bottom to steady the frame etc complete all as specified and directed

S & F 30mm thick Fiber glass reinforcement plastic (FRP) panelled door shutter made with fire retardent grade unsaturated polyster resin moulded 3mm thick FRP laminated for forming hollow rails and style with wooden frames and suitable blocks of seasoned wood inside at required places for fixing of fitting cast monolithically with 5mm thick FRP laminated for panels etc complete all as specified and directed

S&F Aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with aluminium wire staples etc complete all as specified and directed

Cutting holes in brick work built in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required not exc half brick etc complete all as specified and directed

S & F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section etc complete all as specified and directed

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised etc complete all as directed and specified by Engr-in-Charge.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy etc complete all as specified and directed

S & F Floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 150 mm etc complete all as directed and specified by Engr-in-Charge.

S & F 100 mm long medium weight, stain less steel Butt hinges.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 etc complete all as specified and directed

M&LPrecast cement concrete block masonry with solid blocks (1:3:6), type C4 as per IS -2185 (Part I)2005 , using 20mm graded stone aggregate,exc 10 cm in width and setting in CM 1:4 complete all as specified and directed.

M&L Pre-cast cement concrete solid building block or slab Type C-1 (1:3:6) with using 20 mm graded aggregate 10 cm thick (with plain or interlocking joint as directed) and setting in cement mortar 1:4 ,complete all as specified and directed.

M & L for 75 mm thick PCC (1:2:4) type B1 using 20mm graded stone aggregate as in plinth protection/hard standing finished even and smooth without using extra cement complete all as specified and directed

Forming Contration (Dummy) joints 65 mm deep x 10 mm wide, filled with sealing compound grade 'A' etc complete all as directed and specified by Engr-in-Charge.

M&L for rendering 15 mm thick in cement mortar 1:6 on stone masonry surfaces other than fair faces of brick work and finished smooth and even without using extra cement (Internal) etc complete all as specified and directed

M & L for rendering cement plaster in two coats, 8mm thick in CM 1:4 using WPC over 12mm thick in CM 1:6 on external surfaces finished even and smooth without using extra cement all as specified and directed. Note:-WPC shall be measured and paid seperately.

M&L for rendering 5 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 finished even and smooth without using extra cement in Ceiling complete all as specified and directed

Supply only integral water proofing compound

Cutting chases, for water tubing or concealed , etc, and making good to facings where required and plastering in cement mortar (1:4) cutting not exceeding 10cm girth in brick/stone walls etc complete all as specified and directed

S&F Rotational moulded polyethylene water storage tanks of 500 litre capacity triple layered(cylindrical vertical with closed top) ISI marked hoisted and fixed in position all as specified in SSR Part I etc complete all as specified and directed

S & F Ball brass valve 20 mm dia high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule etc complete all as specified and directed

Taking up or down 15 mm bore steel tubing and connections, including cleaning for Refixing or removal to store etc complete all as specified and directed

Taking up or down 20 mm bore steel tubing and connections, including cleaning for Refixing or removal to store etc complete all as specified and directed

S&F 15mm bore medium grade galvanised tube with all fitting & fixed complete to walls or ceiling & laid in floors etc complete all as specified and directed

S&F 20 mm bore medium grade galvanised tube with all fitting & fixed complete to walls or ceiling & laid in floors etc complete all as specified and directed

S & F 20 mm dia powder coated Aluminium alloy anodised curtain rails with brackets etc complete all as specified and directed

S & F in repairs 20 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed in repairs etc complete all as specified and directed

S&F in repairs 15mm Bib Taps with wall flange of chromium plated fancy type long shank screwed for Iron Pipe or for brass ferrule etc complete all as specified and directed

S&F two way bib taps with hand faucet with 1.2m brass flexible tube and wall hook mounted type chromium plated for EWC etc complete all as specified and directed

S & F in repairs Fancy type chromium plated with long shank and cup (concealed type) 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed

S&F in repairs Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long etc complete all as specified and directed

S & F in repairs Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union etc complete all as specified directed

S & F in repairs Vitreous Ware wash down water closet (Pedestal), white (EWC) and fixed in repairs etc complete all as specified and directed

S&F In repair only Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hing device etc complete all as specified and directed

S & F PVC Low level flushing cistern 10 Ltr capacity including all fitting ball valve, float and handle incl brackets etc complete all as specified and directed

S & F in repairs Vitreous China Ware Wash hand basin white, flat back, 550x400 mm size oval type in repairs including cutting for and pinning ends of brackets or erecting stand etc complete all as specified and directed

S&F in repairs PVC connection of 15 mm size with PTMT nuts of length 450 mm long with brass checknut and union etc complete all as specified and directed

M & L for PVC (SWR) multi floor trap diameter of outlet 100mm with grating including jointing with solvent cement etc complete all as specified and directed

S & F in repairs Brass Chromium plated tubular towel rail, 20 mm dia., D Type, 60 cm long between flanges etc complete all as specified and directed and

S & F in repairs Soap dish, vitreous China white of approximate size 160 x 160 x 90 mm etc complete all as specified and directed

S&F in repair Toilet paper holder of brass with chromium plated fixed to walls with chromium plated (CP) brass screws etc complete all as specified and directed

Supply and fix in repairs of CP brass pillar tap 15mm dia screwed down for iron pipe etc complete all as specified and directed

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110mm bore.

S&F PVC (SWR) bends of any radius 110mm bore with access door.

S&F PVC(SWR) vent cowl 110mm bore.

S&F for 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed.

S&F PVC (SWR) bends of any radius 75 mm bore with access door etc complete all as specified and directed

S&F 40 mm dia HDPE pipe of pressure rating 6kgf/sqcm laid in trenches etc complete all as specified and directed

M&L preparation of new surfaces of wall and applying two coats of acrylic emulsion over a coat of alkali resistant primer over 3mm thick of wall care putty etc complete all as specified and directed

Complete removal of existing treatment and applying two coats of acrylic emulsion over a coat of alkali resistant primer over 3mm thick of wall care putty etc complete all as specified and directed

M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed

Preparation of old treated surfaces of ceilings and applying one coat of white wash complete all as specified and directed

M&L for preparation of new wood surfaces and applying two coats of synthetic enamel paint over coat of pink primer over 10cm width or girth etc complete all as specified and directed

M&L for one coat of synthetic enamelled paint on wooden surfaces over 10cm width or girth including preparation on old surfaces etc complete all as specified and directed

Preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and directed.

Preparation of old steel surfaces and applying one coats of synthetic enamel paint exc 10cm width or girth etc complete all as specified and directed

M&L for preparation of newly plastered surfaces and applying two coats of antifungal exterior coating emulsion paint over a coat of anti fungal primer complete all as specified and directed

M&L for preparation of old painted surfaces by removing the existing treatment completely and applying two coats of exterior emulsion paint over a coat of primer over 3 mm thick of wall care putty complete all as specified and directed

M & L for Providing and injecting chemical emulsion Anti Termite Treatment of soil under existing floors using chemical emulsion at the rate of One liter per hole, 300 mm apart including drilling and plugging 12 mm dia., holes with cement mortar 1:2 to match the existing floors.

M & L for treating the soil along the external perimeter of building at the rate of 2.25 litres of emulsion per metre of the perimeter wall.

E/M PORTION:-Taking down carefully copper/ aluminium point wiring (Light, fan, socket or power) complete (fittings such as switches, ceiling roses, pendants, regulators, sockets, DB's) etc all as specified and directed .

Taking down carefully unserviceable main switches and DBs including wooden boards, garden lights and removing from site including making good disturbed sufaces of wall all complete as specified and as directed.

Dismantling and taking down fluorescent tube light single double of any wattage or size, street light fittings for repair or replacement of bunt/worn out accessories.

Concealed Point wiring with PVC insulated unsheathed multistranded single core copper conductor cable ISI marked, 1100 Volt grade, FRLS of size 1.5 sq.mm, through and including rigid non metallic ,ISI marked PVC conduit and all accessories, including suitable size modular metal box,modular white cover plate with frame & 1.5 sqmm PVC insulated unsheathered multistranded single core copper conductor FRLS,ISI marked cable as earth continuity conductor,cutting chasis,and making good disturbed surfaces etc complete all as specified & directed for (a) One light point/bell point/ fan point controlled by one switch ( Note :(i) Rate include cost of making MS box in concealed for cutting and sinkings for boxes and making good to walls , No extra paymemnet will be made for the same.(ii): Rate include the logic modular plates, Necessary blank Plates as required at site. )

All as per item No 140 above but for 05 Amp switch socket in same board all as specified and directed .

All as per item No 140 above but for 05 Amp switch socket independent board all as specified and directed.

All as per item No 140 above but for 15 Amp switch socket independent board one 3 pin socket outlet, 15 Amps, independent with cables 2.5 Sqmm size all as specified and directed.

S&F Modular switch 01 way 6A, 1 module all as specified and directed.

S&F Modular switch 01 way 16A, 1 module all as specified and directed .

S&F Modular socket 6A- 2/3 pin combined 2 Module all as specified and directed.

S&F Modular socket 16A- 2/3 pin combined 2 Module all as specified and directed.

S&F ceiling rose surface Bakelite 65x50mm three terminals all as specified and directed.

S&F sheet metal enclosures for DB's when MCB's to be used Single pole and neutral, 12 way Double door, 240 A Volt with 200 Amps rated Bus bar complete all as specified and directed.

S&F sheet metal enclosures for DB's when MCB's to be used Single pole and neutral, 08 way Double door, 240 A Volt with 200 Amps rated Bus bar complete all as specified and directed.

S&F sheet metal enclosures for DB's when MCB's to be used Single pole and neutral, 04 way Double door, 240 A Volt with 200 Amps rated Bus bar complete all as specified and directed.

S&F sheet metal enclosures for DB's when MCB's to be used triple pole and neutral, 04 way Double door, 415 Volt with 200 Amps rated Bus bar complete all as specified and directed.

Supply and fix MCB 240 V, 50 HZ, 10 KA suitable for lighting and other domestic loads Rating 06 to 32 Amp SP Cat No 4085 87 to 95, Make: Legrand / Indoasian/ Havells/ L&T complete all as specified and directed.

Supply and fix SPN MCB 32 A 240/415V, 50HZ, 10KA, 4086 14-17,Make: Legrand / Indoasian/ Havells/ L&T complete all as specified and directed.

Supply and fix Isolator TPN 63 A 415 V, 50 Hz, suitable for lightning and other domestic loads,Make: Legrand / Indoasian/ Havells/ L&T complete all as specified and directed.

S&F three phase 63 A, 5 Pin (3P+N+E) Metal Plug and socket of four modules suitable for Surface and flush mounting 415 V 50 Hz Make Legrand Cat No DBMPS463SD or equivalent in Indoasian/ Havells/ L&T complete all as specified and directed.

S&F LED 4' Glaze LED Batten high quality design aluminium extruded with decoative end caps LGLZ01x024xC 24 W CCT: 6500 Make : Jaquar/Wipro/Philips complete all as specified and directed.

S&F LED 2' Glaze LED Batten high quality design aluminium extruded with decroative end caps LGLZ01x010xC 10 W CCT: 6500 Make : Jaquar/Wipro/Philips complete all as specified and directed.

S&F LED 72W security light/ Street light fitting in aluminium pressure die cast housing with glass cover & lens IP 66 CCT(k) 6000 Cat No LSRT01S072XC Make : Jaquar or equivalent in Wipro/ Havells/Bajaj complete all as specified and directed.

S&F 32mm size and suitable bend GI bracket for street light fittings 1.50M long of above the item holed by shaddle include all accessories to fix on corner of the building.

Supply and fix ceiling fan complete with electronic type regulator and accessories 230V 1400 mm sweep. Make-Havells Model No - Velocity ES-50 ISI Mark, and white colour, including taking down old existing fan shall be deposited to mes store yard complete all as specified and directed.

Supply & fix 300 mm sweep exhaust fans metal body, AC single phase 230/240 V with lower shutter ventil Air Make- Bajaj, Model No Supreme Plus 300 mm 900 RPM Ind EX Fan including taking down old existing fan shall be deposited to mes store yard complete all as specified and directed.

M&L sub main wiring along with earth wire with the following sizes of 2x4.0 sqmm and 1x4.00 Sqmm earth continuity conductor and connected to earth dolly, PVC insulated single core multi stranded copper conductor cable FRLS type drawn through PVC casing capping of dia not less than 20 mm width and including accessories etc complete all as specified and directed including taking down the existing complete.(Note: 03 runs of conductors and one run of PVC conduit shall be measured as one run only )

M&L sub main wiring along with earth wire with the following sizes of 4x6.0 sqmm and 2x6.00 Sqmm earth continuity conductor and connected to earth dolly, PVC insulated single core multi stranded copper conductor cable FRLS type drawn through PVC casing capping of dia not less than 50 mm width and including accessories etc complete all as specified and directed including taking down the existing complete.(Note: 06 runs of conductors and one run of PVC conduit shall be measured as one run only )

M&L sub main wiring along with earth wire with the following sizes of 2x6.0 sqmm and 1x6.00 Sqmm earth continuity conductor and connected to earth dolly, PVC insulated single core multi stranded copper conductor cable FRLS type drawn through PVC casing capping of dia not less than 20 mm width and including accessories etc complete all as specified and directed including taking down the existing complete.(Note: 03 runs of conductors and one run of PVC conduit shall be measured as one run only )

M&L for shifting of LT feeder pillar by disconnecting existing cable connection -04 cables and reconnect the same by providing new LT straight through joint of size 50 to 95 sqmm 04 Nos including necessary PCC foundation complete. Note:-Excavation & earth work will be measured and paid under relevant items.

Supply and lay including taking down old cable XLPE insulated screened ,PVC bedded,galvanised steel strip or wire armoured,heavy duty electric cable with aluminium conductor,1100 volts grade with stranded aluminium conductor in trenches/fixed on wall of 50 Sqmm 3.5 core sectional area complete all as specified.

As per item No.167 but 25 Sqmm 4 core

As per item No.167 but 16 Sqmm 4 core

Supply and Lay HDPE (High Density Polyethlene Pipe) of pressure rating 6 Kg/ cm 2 for protection of cable laid in trenches of Size 50 Sqmm inner dia complete all as specfied and as directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60x60cmx6.0 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron wire of 4 mm by means of bolt, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected or indicated including testing on completion including necessary excavation, earth work, pcc pit in 1:3:6 (Type C1), RCC cover in 1:2:4(Type B1) reinforced with 8mm dia @150mm c/c bothways, funnel with watering pipe 20mm bore light grade, GI protection pipe 15mm bore light grade complete all as specfied and as directed.

ARBORICULTURE:-TREES : Digging of pits of size 1x1x1 mtr, removal of debris, weed roots etc.refilling with good soil and cattle manure in 4:1 ratio, provn of antitermite treatment at plantation time including supply and planting of approved saplings (Coconut, Bottle palm, Manilkara Zapota, Ashoka,Mango,guvava,Red palm etc.) Sapling should be healthy, grown up with good root system and minimum 4 feet ht from ground level after plantation. Maint: including watering loosening of soil fortnightly manuring with fertilizer, trimming, pruning, stacking and spraying of insecticide and fungisides as and when required. Clearing of any type of vegetation in and around the plantation area for a period of 03 years all as specified and as directed.

SHURBS: Digging of pits of size 0.60x0.60x0.60 mtr ,and refilling with good soil and cattle manure in 4:1 ratio, supply and planting of approved species of healthy grown up sapling with good root system min: 2 feet from ground level (Bougain villa, Song of India,drackenia,Ixora,Ticoma,Nirivim Red etc.) Rest of the activities as shown in item No.172 above for a period for 03 years all as specified and as directed

Lawn:- Loosening of soil, removing of weed roots and refilling with agricultural soil and cattle manure in the ratio 4:1. Provn of ATT, mixing, leveling and planting of deep mexican grass and maint: of a period of 03 Years all as specified and as directed.

Ground cover: Digging up to 0.3 mtr, refilling with agricultural soil and cattle manure in 4:1 ratio. Provn of ATT at plantation time. Supply and planting of healthy grown up plant material (Chandani Double,Chandani Single,Red ruhy,Erem Thirma Black,Erem Thirma Green,Acalipha Java etc.) rest of all activities as shown in item No:172 above a period of 03 years all as specified and as directed.

vishalconstruction

Honest builders

SIBS CONTRACTOR

Sagar Builders

nasreenenterprise

Jyoti Refrigeration