Tender for special repair and renovation of Girls Hostel of South Campus Bhainswal Kalan at BPSMV Khanpur Kalan.

Amount

New work (two or more coats) over and including water thinnablepriming coat with cement primer ( HSR-11.64.1)

Dismantling old plaster or skirting raking out joints and cleaning sqmthe surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. (HSR-5.45)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead: Of area 3 sq. metres and below (HSR 5.29.1)

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles above 25 mm and up to 40 mm (HSR-5.43.2)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1 :6 (1 cement: 6 fine sand)(HSR-11.6.2 )

Supply & fixing Windows frames (Chowkhats) including mullions consisting frame fabricated from sheet roll formed out of 1.2mm thick galvanized sheet as per IS:277 (Base steel as per IS 513) with zinc of 120 gm/sqm & Powder coated with pure Polyester powder up to 50 microns (as per approved colour), 3 Nos. 100mm butt - hinges 2mm thick, 6 Nos. 1.2mm thick CRCA electroplated stiffner, 6 Nos. M.S hold fast with split and tail welded to stiffner plate 200mm long, receiver for aldrop, weld less corner assembly with brackets & screws, M.S tie rod 50mm x 25mm to be fixed at bottom finished with powder coated total thickness of coating 0.6mm of approved shade, fixed in position including the cost of cement concrete for 1 :2:4 for fixing lugs complete in all respects as per drawing, design, specification & entire satisfaction of Engineer-in-charge. Door Frame of size 80mm x 50mm with 37mm wide single rebate metre for 35mm door shutter (HSR- 13.21.1 )

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.n gratings, frames, guard bar, ladder, railings, brackets, gates and similar works (HSR-13.29.2)

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : 00x60x2.50 mm (HSR-12.74.2)

Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face eneers on both faces of shutters: 30mm thick including ISi marked Stainless Steel butt hinges with sqm necessary screws (HSR-12.37.2)

Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm (HSR-12.98.2)

Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 150x10 mm (HSR-12.99.4)

Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1 mm, painted with primer , all four comers of reinforcement to be welded or sealed. Solid PVC extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100 mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8 mm complete as per manufacturer's specifications and direction of Engineer-in-charge. Decorative finish (both side wood grained finish) (HSR-12.122.2) 30mm thick PVC door shuters

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary 12.20 12.21 12.22 screws: Kiln seasoned and chemically treated Hollock wood (HSR-12.19.1.1.2)

Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) tansparent or dyed to required colour or shade, with necessary screws etc. complete I-125mm (HSR-12.102.1)

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with - I 4.0 mm thick glass panes (HSR-13.10.1)

Brick work with common burnt clay non-modular bricks of class designation 7 .5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : Cement mortar 1:6 (1 cement: 6 coarse sand) (HSR-7.22.2)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. ( HSR 11.78)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: 11.96.1 New work (Two or more coats applied @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) (HSR-11.96.1)

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete (HSR-30.22)

Providing and applying two coats white cement based putty of approved sqm 26 10 36 brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete (HSR-11.58)

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M .S. Flat 15x3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4mm aperture on both sides (HSR-13.9.2)

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1 :3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (HSR-10.58)

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1 :4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. (HSR-10.60)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm (HSR-10.63.2)

Providing and fixing of Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand) : 25 mm thick (HSR-10.37.1)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement sluny mixed with water proofing cement compound consisting of applying (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound@ 0.253 kg/ sqm This layer will be allowed to air cure for 4 hours. (b) Second layer of sluny of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. (HSR-28.15)

Providing gola 75x75 mm in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per standard design : (HSR-9.17)

Providing and laying 80mm thick factory made cement concrete inter1ocking paver block of M -35 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over (BIS 15658:2006) and including 60mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.(HSR-10.77)

1:2:4 (1 cement : 2 coarse sand (zone-Ill) : 4 graded cum stone aggregate 20 mm nominal size) (HSR-6.1.2)

Compaction of Earthwork Compaction of & preparation of sub grade including loosening, levelling of earth 225 mm thick top layer, rough dressing of soil, final dressing of earth to give level, camber, watering, rolling with road roller, compacting the bed to achieve minimum dry density as given in the Table 3000-2 as per technical clause 305 of MORT&H specifications (in case of link roads earthwork to be done by villagers) (HSR-17.5.3)

1 :4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded cum stone aggregate 40 mm nominal size) [HSR 6.1.6)

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore (HSR-22.107.1)

Providing and fixing Unplasticised PVC connection pipe with brass unions 15 mm nominal bore (HSR-22.101.2.1)

Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISi : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately (HSR-22.182)

1000 Ltrs. Capacity Water Tank

500 Ltrs. Capacity Water Tank

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore (HSR-22.105.1)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore (HSR-22.103.3)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 40 mm dia (HSR-22.14.2.2)

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 1 o litre capacity - White (HSR-22.39.1)

Providing and fixing PTMT grating of approved quality and colour Circular type (HSR-22.123.1)

Providing and fixing in position 25 mm diameter mosquito proof coupling of each 1 39 40 approved municipal design. (HSR-22.41)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 25 mm dia nominal bore (HSR-22.88.3)

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter (HSR-9.57.2)

Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 1 O mm gap for thermal expansion. 110 mm bend (HSR-9.58.2)

Extra for forming cavity 5 cm to 7.5 cm wide in cavity walls with necessary weep and vent holes including use of cores and cost of providing and fixing M .S. ties 300 mm long of 25x3 mm section at not less than 3 ties per sqm as per approved design & laid wire mess (25x25 mm)below plaster on cracks. (DSR:-6.6)

P & F water storage tank cover with all accesseries complete in all respect (Heavy Duty) ( N.S.)

Electrical Items Wiring only in 1.5 sqmm PVC insulated copper conductor cable for LIGHT/FAN/Call bell point in existing conduit pipe and MS boxes including cost of Bakelite cover for MS box, switch, wall socket, ceiling rose/connector etc. HSR – 23.5.1.1 Group A

Wiring in existing conduit and MS box for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin socket and 1 no 5/6 Amp switch etc complete as required HSR – 23.5.4.1 Group A

Wiring in existing conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin socket and 1 no 15/16 Amp switch etc complete as required HSR – 23.5.4.1 Group A

FITTING AND ACCESSORIES Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. HSR – 23.8.1.12 Bakelite angle/straight button holder large size.

Wall socket 5 amp on existing sheet. HSR – 23.8.1.2

Ceiling rose flush/surface type HSR – 23.8.1.5

Switch 5 amp. on existing sheet. HSR – 23.8.1.1

Fixing of LED Down lighter 7 to 28 Watt on ceiling or in false ceiling , including cutting/making hole in ceiling including making connections etc as required HSR – 23.21

Replacement of ball bearing of a ceiling fan including greasing, re-assembling and testing etc. HSR – 23.15

Replacement of a fan condenser complete with connections and testing etc. 4 to 6 mfd. HSR – 23.17.2

Supply and Fixing 3 mm thick Bakelite sheet cover on existing MS/PVC junction box/tee etc including fixing with brass screws and washers. HSR – 23.8.12

Supply and erection of suitable MS/GI Box covered with 3 mm thick Bakelite sheet as below 200 mm X 150 mm X 60 mm deep metal box HSR – 23.8.3.4

250 mm X 300 mm X 60 mm deep metal box HSR – 23.8.3.5

Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 1.50 Sqmm(1/1.40mm) HSR – 23.5.6.1

1 run of Size 4 Sqmm(1/2.24mm) HSR – 23.5.6.3

Supply and erection of miniature circuit Breaker/isolator 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole HSR – 23.22.5.1

6 amp. to 32 amp MCB's FOUR POLE HSR – 23.22.5.7

40 amp to 63 amp. MCB's FOUR POLE HSR – 23.22.5.8

EARTHING AND LIGHTENING ARRESTOR Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc.or coke and salt) as required. HSR - 24.1.1 (but without charcoal

Extra for using salt and char coal/coke for pipe earth electrode as required. HSR - 24.1.2

Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop carthing as required. HSR - 24.1.13

Supply and erection of 20mm x 3 mm thick GI, tape fixed with suitable G.I. stapples of same size. HSR - 24.1.14

Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required. HSR - 24.1.3

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 4 way ( 2 incoming and 2 outgoing) HSR – 23.22.4.1

SPN DB Double Door 8 way ( 2 incoming and 6 outgoing) HSR – 23.22.4.2

Vertical TPN DB Double Door 4 way ( 8 incoming and 3phase*4 outgoing) HSR – 23.22.4.9

Vertical TPN DB Double Door 8 way ( 8 incoming 3phase*8 outgoing) HSR-23.22.4.11

Laying and fixing of cable on surface/ cable tray etc as required:- 2.5 Sq mm to 10 Sq mm 2 to 4 Core HSR – 24.2.5.1

16 Sq mm to 35 sqmm 2 to 4 Core HSR-24.2.5.2

50 Sq mm to 150 sqmm 2 to 4 Core HSR-24.2.5.3

Supply and erection of aluminium lugs heavy duty including crimping etc. upto the entire satisfaction of the Engineer-in-charge of the work. 4 sqmm to 6 sqmm HSR – 24.2.8.2

16 sqmm HSR – 24.2.8.4

70 sqmm HSR – 24.2.8.8

Supply and erection of suitable compression type brass cable glands for underground Cable 10 sqmm to 16 sqmm Cable 2 to 4 Core :- HSR – 24.2.7.2

70 sqmm to 95 sqmm Cable 3 to 3½ Core HSR – 24.2.7.4

Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Socket size rotary step type Electronic regulator for A.C. ceiling fan HSR – 23.8.1.13

Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 100 amp HSR – 23.22.1.9

MCCB Enclosure made of Sheet Steel suitable for mounting MCCB of following ratings. MCCB up to 125 A FP HSR – 23.22.2.1

SITC Four pole ON LOAD Manual change over switch in SS enclosure of following Ratings . 100 amp 415 volts HSR – 23.22.8

Erection of exhaust fan in existing opening ,complete with necessary earthling of fan including carriage from PWD store to the site of work. HSR-23.9

Erection of cabin fan complete with necessary earthling including carriage from PWD store to the site of work. HSR-23.10

Supply and erection of 32mm dia metre 1.5 m long bracket (B-class) making an angle of 10° to 15° with horizontal plane for mounting street light fitting fixing of GI. bracket on wall with 2 nos. 32 mm x 3 mm thick M.S. clamps including cost of cutting, welding of G.I. pipe complete with cement sand mixture, bolts and nuts etc. including necessary connections. HSR – 24.4.3

Supply and erection of Single Phase weather proof M.S. box of size 20 cm x 15 cm x 10 cm with hinged cover made of 2 mm thick MS sheet, locking arrangements, housed in wall/fixed on pole , including the cost of 1 no 4 way 16 A bakellite connector, 1 no. 6 amp SP MCB and 1 Nos. 16 amp. neutral links fixed on bakellite sheet in the M.S. box including painting and necessary connections. HSR – 24.4.5

Erection of street light fitting on the pole including the cost of petty material required (irrespective of height/length of bracket) At Pole upto the height of 4.5 metres HSR – 24.4.4.1

Supply and erection of M.S. angle iron frame duly welded for housing M.S. sheet & main switches etc. on it, fixed on wall by means of suitable size of rag bolts with cement concrete, duly painted with three coats of approved paint including one coat of red oxide. HSR- 23.24.1

Supply erection testing of Ceiling fans IS marked (as per IS code 374) with sultable GI pipe complete in all respects complete as per direction of Engineer-In-charge 48'' (1200mm)HSR – 20.71.1

Supply and erection of GI saddles HSR- EL - 314

MS Clamps HSR – EL 35

Supply of PVC /XLPE insulated (Heavy Duty) electrical cable for working voltage upto and including 1100Volts to IS 1554 (Part –I) 1988/7098 (Part-I) with aluminium conductor – ISI mark including transportation, loading and unloading etc. complete in all respect. 06 Sq.mm 2 core cable (Ard.) (NS) – 1

16 Sq.mm 4core cable (Ard.) (NS) – 2

70 Sq.mm 3.5 core cable (Ard.) (NS) – 3

Full stator rewinding of an exhaust fan ( condenser type ) including cleaning and insulating the stator slots , sleeving , soldering , wrapping of cotton tape varnishing , re-assembling and testing etc. Complete in all respect up to the entire satisfaction of Engineer – in-charge of the work. (i) 380 / 450 mm sweep 1400 RPM . (NS) – 4

Supply of LED Batton 18watt. / 1800 Lumen, Length of tube light 1220mm, Voltage 100-300 Volt AC, Rated voltage for performance and life 220-240 Volt, Make:- Bajaj, Philips, Havells or Equivalent make and Model (NS) – 5

Supply of LED Street Light Fitting 90watt. Voltage 90-300 Volt AC, Rated voltage for performance and life 220-240 Volt, IP - 66 Colur temperature 6000+/-500K, Make:- Bajaj, Philips, Havells or Equivalent make and Model BRLEP90watt. (NS) – 6

Supply and erection of 50 liter 5 star water heaters (Gyeser ), capacity 50liters, BEE Star Rating - 5, Material of inner Container stainless steel, Material of outer container:- CRCA, Minimum Lengh of Fiexible Cable with 3 pin plug of 16amps. 2mtr Model no. SHAKTI 50L 2000watt. Make:- Bajaj or equivalent make Racold, Havells (NS) – 7

Supply of LED flood light fitting 150 watt. Luminaries with ultra sleek, light weight and with secondary optics made of pressure die-cast housing with IP66 ingress protection and impact resistance of IK07, 4KV inbuilt and 10KV external surge protection , Bajaj make or equivalent Havells, Philips , Complete in all respect up to the entire satisfaction of Engineer - incharge of the work. (NS) – 8

THE KHAIRWAL CO OP L AND C SOCIETY LTD

SATISH KUMAR GUPTA

R K CONSTRUCTION CO.