REPAIR/REPLACEMENT OF ALUMINIUM DOOR/WINDOW PARTITION, RAIN WATER PIPES,PLINTH PROTECTION AND CERTAIN MISC WORKS IN ZONE V UNDER GE (WEST) BAREILLY.

Demolition of brick work built in cement mortar complete all as specified and directed.

Demolition cement concrete(un reinforced)in ground floor and packing n exc 15 cm thickness (bellower above ground level) complete all as specified and directed.

Demolition of Roof, floors (Other than ground floors ) beams,Staircase ,landing chajja,and similar suspended work in cement concrete is reinforforced (reinforcement cut as required to facilitate demolition complete all as specified and directed.

Taking down cement plaster from brick wall including racking out joints hacking for key and scrubbing down with water complete all as specified

Dismantling asbestos cement, galvanised sheet (corrugated,semi corrugated etec ) sheets in roof covering complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M & L for brick work with sub class ‘B’ brick straight or curved on plan exc 6 Mtr mean radius built in CM (1:6)

All as per item no 7 above but except bricks

Removing Cement mortar or cement lime mortarr from and cleaning bricks, stacking for measurement including all extra handling and removal and disposing off rubbish etc complete all as specified and directed.

M & L Galvalised mild steel wire netting of chicken wire mesh 0.46 mm nominal dia of wire & 10 mm mesh size all as spd fixed to wallsroof etc & directed by Engr-in-charge.

M&L for 15mm thick rendering on surfaces of brick work or stone walling in CM 1:6 finishing the surface fair & even complete all as spfd and directed.

M&L for 15mm thick rendering on brick work or concrete surface in CM 1:4 mixed with WPC @ 2% by weight of cement finishing the surface fair & even complete all as spfd and directed. Note:- WPC shall be measured and paid saperately.

M&L for rendering 10 mm thick on concrete surfaces like ceiling, chajja etc in cement mortar 1:3 and finished even and smooth without using extra cement icomplete all as specified and directed

Supply only integral water proofing compound

M & L for preparation of newly plastered surfaces of wall and applying one coat white wash complete all as specified and directed

M&L two coats of white wash on newly plastered surfaces as on ceiling including preparation of surfaces, complete all as spfd and directed.

M & L for Preparing new plastered or unplastered surfaces of walls and applying one coats of cement base paint white or tinted over & including a coat of white cement wash complete all as specified and directed.

M&L for preparation of plastered old surfaces of walls and applying two coats of distemper (washable) oil emulsion paint on walls complete all as specified and directed.

Cutting of tree from wall or roof of building n.exc 30 cm girth taking out tree trunk portion completely from wall/roof, digging out roof and making good distusbed surface with brick work in CM 1:4 or filling PCC 1:2:4 type B1 using 20mm add stone aggegate complete all as specified and directed. (Roof in non accessible approx height ex. 4.00 m and n.exc. 8.00 m complete as directed. (Necessary scafolding shall be included in the cost )

M&L providing PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in bed plates coping, padding complete all as spd & directed (Roof in non accessible approx height ex. 4.00 m and n.exc. 8.00 m complete as directed by Engr in Charge ( Necessary scafolding shall be included in the cost )

M&L Cutting out cracks to 'V' section in existing roof or terraces cleaning out wetting groves and suppling and filling cement mortar in CM (1:3) complete . (Roof in non accessible approx height ex. 4.00 m and n.exc. 8.00 m complete as directed by Engr in Charge ( Necessary scafolding shall be included in the cost )

M&L for water proofing treatment to roof including taking down old the existing roof treatment of any type and preparation of surface by proper cleaning and applying a priming coat of bitumen primer @ 0.30 ltrs/Sqm and applying a coat of hot blown bitumen 85/25 conforming to IS-702 @ 1.20 Kg/Sqm and supply & Laying ofAPP modified polymeric water proofing membrane 3 mm thick without comsidering mineral (weight not less than 3.50 Kg/Sqm )by LPG torch method over entire area with 100 mm overlapping and sealed and applying another coat of hot blown bitumen 85/25 @ 1.2 Kg/Sqm and applying two coat of aluminium paint @ 100 gm/Sqm on roof over roof treatment or vertical surface complete all as specified & directed.. (Roof in non accessible approx height ex. 4.00 m and n.exc. 8.00 m complete as directed by Engr in Charge ( Necessary scafolding shall be included in the cost )

M&L Bitumastic gola, with 80/25 bitumen and coarse sand mixture. 1:3 by weight, 8cmx8cm at the junction of roofing to vertical surfaces complete all as specified & directed. (Roof in non accessible approx height ex. 4.00 m and n.exc. 8.00 m complete as directed by Engr in Charge ( Necessary scafolding shall be included in the cost )

M & L for Wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown grade bitumen of any penetration applied hot @ 1.7 kg per sq. m, blinded with grit or pea size gravel @ 0.006 cu.m per sq.m, and lightly tampered (area of flashings, etc., shall be added to the roof area) complete all as specified & directed. (Roof in non accessible approx height ex. 4.00 m and n.exc. 8.00 m complete as directed by Engr in Charge ( Necessary scafolding shall be included in the cost )

S&F welded steel wire fabric weight n' exc 4 Kg per Sq.m as in extra reinforcement to RCC menbers including all cutting, bending and binding complete all as specified and directed

M & L for plain cement concrete 1:4:8 type D-2 (Using 40mm graded stone aggregate ) as in foundation filling & mass concrete complete all as spd and directed

M & L for Cement concrete 1:3:6 type C-1, using 20mm graded stone aggregate , in flinth protection 50mm thick finished even and smooth without using extra cement including making joint 12mm wide to the full depth of PCC at every 3 mtrs and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as spd and directed

M & L Proviiding 100mm thick Cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in surface finishing cement concrete surface even and smooth complete all as spd and directed

M & L for Formring construction joints 30mm deep x 10mm wide filled with sealing compound grade "A" complete all as spd and directed

M & L PCC (1:3:6) type C-2(using 40mm graded stone aggregate) as in surface channels and drains complete all as specified.

Extra for forming fair finished drain or channels 30cm inner girth in cement concrete , using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified

S&F of steel windows with pressed steel frame (size 95mm x 456 mm x 1.25mm) side hung shutter including box types hinge with steel handle , and steel pegs steel complete with glazed openable shutter with glazing bar (open out side) and wire gauged openable shutter without glazing bar (open in side )dovetails or welded complete all as specified and directed and all as per Drg NO TD/088 Dt 07 jan 2002 Note:-(a)Two shutter is wire gauged and glazed shall be fixed in one composite frame and both shutter shall be measured as one unit . (b)rate for filling of pcc in frame deemed to be included in quote rate.(c) ms grill shall be measured and paid including under relevant item of schedule

M & L for Rolled mild steel sections conforming to Gde Fe-410-0 or Fe-310-0 as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails & guides for sliding doors, fixed with angle cleats or other connecting plates complete all as spd and directed

M & L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete gde Fe-410-W or GDe250-A quality complete all as spd and directed

S&F wind ties for roof incl securing bolts, including all necessary drilling, bolting or riveting, etc complete all as spd and directed

S & F 6 mm thick asbestos cement, corrugated or semi corrugated sheets in roof, walls etc fixed L type or J type Hooks complete all as spd and directed

All as per item no above but expect sheets

M & L asbestos cement 6 mm thick two Pices adjustable plain wing Ridge fixed with L type or J type hooks complete all as spd and directed

S& F Pre -paited galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an color having tensile strength of 550 MPa as in roof covering /cladding to wall ,fixed with self tapping screws as spd complete all as spd and directed

S& F Pre -paited galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an color having tensile strength of 550 MPa as in roof covering /cladding to wall ,fixed with self tapping screws as spd complete all as spd and directed

S& F 0.80 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as spd and directed

M&L Plain Cement concrete 1:2:4 type B-0 using 12.5 mm greded stone aggregate in leveling course ,benching etc ,finished even & rough to receive cement mortar screed bed complete all as spd and directed

M & L Reinforced Cement Concrets type B -1 1:2:4 (using 20 mm graded stone aggregate) as in Chajjas, shelves etc. complete all as spd and directed

S & F Mild steel TMT bars 10mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending ,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as spd and directed

M & L Form work to chullah hoods, shelves, chajjas, through and similar items including edges in flat surfaces for rough finish surfaces complete all as spd and directed

Taking up or down 15 mm bore steel tubing and connections complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections complete all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.

S & F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed for 20 mm bore dia of pipe.

S & F shelf of PTMT fixed and including chromium plated brass screws & wooden/plastic cleats (Minimum weight 300 gms) complete all as specified and directed.

S & F Vitreous china squating pan orissa pattern size 580 x 440 mm white with integrat foot rest fixed in repairs including provision of lime concrete bedding complete all as specified and directed.

S & F Vitreous china wash hand Basin white flat back size 550 x 400 mm including bracket and cutting for and pinning in ends of brackets, fixed in repair complete all as specified and directed.

S & F in repair 15 mm dia brass chromium plated pillar tap fancy type with fly nut capstan head screwed for 15 mm dia pipe complete all as specified.

S&F PVC connections 15 mm Size with brass check nuts of lenth 450 mm

S & F in repair PVC low level flushing cistern 10 Ltr capacity, white with all fittings and fixtures including brackets and 32 mm bore PVC flush pipe.

s&F chromium plated shower roses 75mm size in repair with or without swivel joint any size including fixing to steel pipe or union complete

S & F in repair bib tap cost copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule in 15 mm bore complete.

S & F in repair stop valve cast copper alloy screwed down, high pressure with crutch or butterfly handles screwed both ends for iron pipe or for unions, 15 mm dia of pipe complete all as specified and directed.

S&F in repair angle valve cock CP in repair fancy type half /full turn 15mm bore flanges approved by Engr-in-Charge

S&F stop cock ,cast copper alloy,chromium plated ,fancy type ,with long shank and cup ,screwd down screwed down high pressure with crutch or butterfly handle and screwed both ends for unions 20mm bore as fixed in repair all as specified

S & F Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including S & F cantiliver bracket of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm fixed in repairs complete.

S&F vitreous china wash down water closet pan pedestal pattern white (excl fixing bolt flushing cistern and flush pipe ) fixed in repairs complete with seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminum hinging device complete all as spfd and directed.

S & F in repair 32 mm waste fittings/coupling of CP WHB ,Sink complete all as specified and directed.

Dismantling & breaking up drains pipes 100/75 mm (Saltglaged ware ,AC,PVC) Set in cement mortar

S & F PVC (SWR) pipes double socketed in any length with rubber Ring joints fixed to walls 110 mm bore fixed complete.

All as per Item No 66 but 75 mm bore complete.

S & F PVC (SWR) bends any radius 110 mm bore fixed in repair complete.

All as per item No 68 but 75 mm bore complete.

S & F PVC (SWR) juntion single T equal or uneqoal 110 mm bore fixed in repair complete.

S & F PVC (SWR) juntion single T equal or uneqoal 75mm bore fixed in repair complete.

S & F PVC (SWR) vent cowl 110 mm bore fixed in repair complete.

BLANK

Cleaning the sunken floor surfaces by wire brushes removing dust and applying following operation :- (a) applying priming coat with bituminous primerconfirming to IS 3384. 1986 @ 0.5 Kg/Sqm (b) Applying a coat of hot bitumen grade 85/25 @ 1.20 Kg/Sqm confirming to Is -705-1998 for water proofing membrance (c) Applying of polymeric water proofing membrane weighting not less than 3 Kg/Sqm over entire area with overlapping and sealed. (d) Again Applying tack coat of hot blown bitumen grade 85/25 @ 1.2 Kg/Sqm.over water proofing membrance (e) Spreading Dry sand @ 0.75 Kg/Sqm dusted over the bitumen indicated

M & L for PCC (1:5:10) type E-2, USING 40mm graded stone aggregate for fiiling up sunken floor over felt complete all as specified and directed.

Taking down Chowkats or frames with shutters (Without taking off shutters from the frames) not exceeding 1.5 Sqm each including iron mongries, hold fast etc and including making good disturbed portions of walls in CM 1:4 complete all as specified and directed.

Taking down Chowkats or frames with shutters (Without taking off shutters from the frames) exceeding 1.5 sqm but not exceeding 4.0 Sqm each including iron mongries, hold fast etc and including making good disturbed portions of walls in Cm 1:4 complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down shutters of any description not exceeding 1 Sqm each complete all as specified and directed.

S&F 125mmx60mmx1.25mm thick pressed steel, frames for door with one or more rebates including filling and compaction with PCC (1:3:6) Type C-1 using 20 mm graded stone aggregate, necessary fixing lugs, hinges, lock strike plate, etc, complete including wooden texture finished paint on the frame surface complete all as specified and directed

S&F 105mmx60mmx1.25mm thick pressed steel, frames for door with one or more rebates including filling and compaction with PCC (1:3:6) Type C-1 using 20 mm graded stone aggregate, necessary fixing lugs, hinges, lock strike plate, etc, including wooden texture finished paint on the frame surface complete all as specified and directed.

S & F 35 mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including teakwood lipping 6mm thick fixed with nails complete all as specified and directed.

M & L for 35mm thick plain framed glazed and skeleton shutter open rebated & prepared to receive glass, gauge etc, without sash bar edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass etc, of 2nd class hard wood , members of shutters as specified in SSR Part - I Section 8 clause 8.24 (a) fitted to chowkats complete all as specified and directed.

Supply and fix Solid PVC door frame of size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube 47x47mm (19 gauge) all as specified and directed.

M&L in providing 30 mm thick brand factory made internal PVC flush door shutter wood free consisting of frame made out of M S tubes of 19 guage thickness and size 20 mm x 40 mm for siles as well as top bottom and lock rail MS frame shall have a coat of metal primer of approved make and manufacturer. The inside panel shall consist of 20 mm thick multichamber hollow PVC section 1 mm wall thickness bonded using solvent cement/ cynoacrylate adhesive with 5 mm (+-0.25 mm) thick plain/prelam PVC sheet manufactured by an ISO-9001-2008 certified company on both side of the inside panel All the four edge of the panel to be sealed with lipping of 10 mm thick and 20 mm wide PVC sheet baton( made by sticking 2 nOs PVC sheet of 5 mm ( +0.25 mm ) thickness using PVC solvent cement adhesive Door edge lipping to be painted with PVC ink of matching colour of plain/prelam moulded PVC sheet of door 0.20 mm thick ( 5mm x 4 mm) thick PVC sheet to be given for lock provision at lock height. Door to be fixed with frame with 3 nos stainless steel butt hinges of size 100 mm * 25 mm * 25 mm and 50 mm long steel screws drilled suitable to pass through both the wall of the MS tube other hardwares should be fixed with 25 mm * 8mm size steel screws etc complete as per direction of engineer-in-charge, manufacturers specification and drawing.

S & F 100 mm long medium weight, cold rolled stainless steel Butt hinges with screws complete all as specified and directed.

S & F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all specified and as directed.

S&F 250 mm long aluminium sliding door bolts plate type with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts, 04 Nos on bolt plate and 02 Nos on staple plate and fix complete all as specified and directed.

S & F 150 mm long Aluminium alloy handles, cast type, anodised complete all as specified and directed.

S & F mild steel 300 mm long ordinary rat rail rod pattern helical door springs, incl roller and roller plate complete all as specified and directed.

S & F in repair Galvanized mild steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified and directed.

S & F Galvanized mild steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified and directed.

S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed.

S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane including hacking out old broken glass (any thickness, size, quality or description) from wooden or metal frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S & F Figured glass, 4.0 mm thick, ordinary quality and glazing with oil putty or wooden beads exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed.

M&L for preparation of new wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coat of Synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified and directed.

M&L for preparation of old wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) complete all as specified and directed.

M&L for preparation of new painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coats of synthetic enamel paint complete all as specified and directed.

S & F in repairs 4mm thick E-Board tiles for insulation and acoustic purpose of size 600x 600mm fixed with and including Powder coated Aluminium snap grid with 25x25x1.5 mm thick Tee section and 38x25x2 mm thick angle with hanging/supporting arrangements as in false ceiling at bottom at spacing 60 cm centre to centre including necessary GI cleats and 4mm dia GI wire as suspender fixed to ceiling not exceeding 1.20 mtr centre both ways with dash fastners complete and making good disturbed surfaces including taking down old ceiling complete all as specified and directed.

S&F Prelam hollow PVC sheet wall panelling of thickness 5mm consisting panels of desired size stuck onhollow inner frame work of 35mm wide strips of 5mm thick PVC sheet. The PVC strips shall be fixed to the wall using 65mm long MS screws through the groove in the strip by using PVC fastners. The distance between two screws shall not be more thant 200 mm. The strips shall be fixed to wall vertically at an equal interval of 10" between two PVC strips. A strip of 5mm thick PVC sheet of width 75mm feathered at edges shall be stuck at the places where two panels are jointed, using solvent cement and including taking down existing PVC wall paneling complete all as specified and directed.

M&L for plain cement concrete types C1 1:3:6(using 20mm grade stone aggregate)as in holdfast and similar work etc complete all as specified and directed

M&L for preparation of Old plastered or unplastered surfaces of walls including brooming down or steel wire brushing scrapping down smoke roof, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying Two coats of Cement based paint of approved shade/tint complete all as specified and directed.

M&L for preparation of Old plastered or unplastered surfaces of walls including brooming down or steel wire brushing scrapping down smoke roof, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying one coats of Cement based paint complete all as specified and directed.

M&L for preparation of Old plastered or unplastered surfaces of wall/roof/Chajja projections including facia, cornices including brooming down or steel wire brushing scrapping down smoke roof, moulds, moss and efflorescent salts and trading oil and greasy spots etc and etc and applying two coat of weather proof exterior emulsion paint upto five story building with necessary scafolding complete all as specified and directed. Note- Emulsion to be carried out through air less spray machine ( Mechanical means), Shade and coloured as approved by Engr-in-Charge.

M&L for preparation of Old plastered or unplastered surfaces of wall/roof/Chajja projections including facia, cornices including brooming down or steel wire brushing scrapping down smoke roof, moulds, moss and efflorescent salts and trading oil and greasy spots etc and etc and applying one coat of weather proof exterior emulsion paint upto five story building with necessary scafolding complete all as specified and directed. Note- Emulsion to be carried out through air less spray machine ( Mechanical means), Shade and coloured as approved by Engr-in-Charge.

M&L for preparation of Old plastered or unplastered surfaces of walls including brooming down or steel wire brushing scrapping down smoke roof, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying one coats of oil bound distemper with roller of approved shade/tint complete all as specified and directed.

M&L for preparation of Old plastered or unplastered surfaces of walls including brooming down or steel wire brushing scrapping down smoke roof, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying one coats of white wash complete all as specified and directed.

M&L for one coats of wall care white putty avg 2mm thick with smooth finish by sand papering to achieve smooth surfaces complete all as specified and directed.

M&L for Vitrified tiles (double charged) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match over and incl M & L for 15 mm thick screed bed in cm 1:6 including dismantling existing tiles complete all as specified and as directed by Engineer-in-Charge.

M&L for Vitrified tiles (double charged) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in wall and cladding or in skirting etc. set and jointed in neat cement slurry and pointed in coloured cement to match over and incl M & L for 10 mm thick screed bed in cm 1:4 including dismantling existing tiles complete all as specified and as directed by Engineer-in-Charge .

M & L for non- skid ceremic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including dismantling of existing old floor or wall tiling and M & L for 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M & L for non- skid ceremic coloured tiles as in skirting/dado 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in verticle surface etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including dismantling of floor or wall tiling and M & L for 15mm thick rendering in cm-1:4 all as spd or as directed.

S & F 1000 Ltr Rotational moulded polyethylene water storage tanks white color triple layered (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of old unserviceable water tank capacity exc 250 but n exc. 500 litre complete all as specified and directed.

S & F 500 Ltr Rotational moulded polyethylene water storage tanks white color triple layered (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of old unserviceable water tank capacity exc 250 but n exc. 500 litre complete all as specified and directed.

S & F in repairs 20 mm bore gate valve , cast copper alloy complete all as specified and directed.

S&F in repairs Ball valves 15mm dia high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15 m m - 2 1 0 g m s ) complete all as specified and directed.

S&F in repair 20 mm dia Stainless steel drappery curtain Rod with bracket and lattu and other connceted accessories etc complete all as specified and directed

S&F in repairs to CP Brass jet spray for EWC complete all as spd and directed

S&F in repairs to CP Brass Health faucet with 1 mtr tube with wall hook complete all as spd and directed

M & L for welding in repair n. exc. 2.5cm in length, thickness of mild steel members to be welded not exc 6mm thick complete all as specified and directed

Repairing of aluminium door/window/ ventilator/ partition wall etc of any size / any number of panels including taking down & refixing (if required) for easy closing/ opening/ tightening of hinges or changing the position of hinges, adjustment of floor door spring of hydraulic door closure, adjustment of tower bolts, sliding bolts etc changing of mortice lock complete all as specified and directed by Engr-in-charge.

Dismantling of plaster of paris ceiling (Gypsum anhydrous) to flat surface including framework and G.I. wire mesh complete all as specified and directed.

M&L POP (Plaster of Paris) false ceiling applying 12 mm thick POP finish over ceiling surfaces with wall care putty mixed with POP powder in ratio of 1:10 (a) PGI sheet of 26 gauge in angle shape of size 25 x 25 mm all around the wall complete. (b) Main runners of 26 gauge PGI sheet in angle shape of size 35 x 25 mm at the interval of 90 cm centre to centre complete. complete including one dome not less than 1 metre dia and frame work complete all as described below : (c) Cross runners of 26 gauge PGI sheet in angle shape of size 35 x 25 mm at 40 cm center to center complete. (d) Suspender/ hanger of 26 gauge of PGI sheets in angle shape of size 25 x 25 mm fixed to soffits of roof by steel fastener complete. (e) S & F Chicken WIre Mesh 12.5mm x 0.51mm (22SWG)

S & F making POP cornices 75/100 mm wide of required design as directed by Engineer-in-charge.

S & F Making POP Dome design( dia exc 90 cm but n.exc 120 cm) of required design as directed by Engineer-in-charge.

S & F in repairs Powder coated aluminium frame for doors, windows, ventilators, Partition with one or more rebates including joining cleat for fixing etc with powder coated complete all as specified.

S&F in repairs Aluminium section powder coated of colour as approved doors frame and shutters partly with 4.8 mm thick reflective glass and partly closed with 5 mm thick aluminium composite panel (alco panel) fixed with aluminium chamfered clip section no 4407 of aluminium door sections as under. (a) Frame 100x40x2mm section No-2420 (b) Shutter style 85x44.45x1.7mm thick section 4546 (i) Top rail 14.30x44.45x1.7mm thick section 4553 (ii) Middle rail 83.50x44.45x1.7mm thick section 4565 (iii) Bottom rail 114.30x44.45x1.7mm thick section 4529 (iv) glazing clip powder coated 0.7mm thick section no 4407 (v) Handle stainless steel 300mm long as approved (vi) Tower bolt powder coated 9.90 mm dia & 200mm long section No 4002 (vii) Mortice lock 100mm 7 lever all as directed .make- godrej ,jaquar,cera.etc (vii) Rubber gasket white PVC (ix) Namda rope to be fixed in the styles's groove for proper air tightness. (x) top guide rail to be provided as per requirment to withstand adequate load of shutter to be installed at site for easy movement of shutter.

S & F in repairs Powder coated aluminium (minimum thickness of powder coating 50 micron) for sliding, thrust rack, windows including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber /neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary fitting , filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws ,bow handles , tower bolt locking arrangement etc all complete as per architectural drawings and the directions of Engineer-in-charge.

S&F in repairs ANODISED aluminium grill (anodised tranparents or dyed to required shade according to IS :1868 WITH MINIMUM ANODIC COATING OF Grade Ac15) of approved design/pattern, with approved standard section and fixing to the existing window frame with c.p brass /stainless steel screw @200mm centre to centre,including cutting the grill to proper opening size for fixing and operation of handlesa nd fixing approved anodised aluminium standard section around the opening ,including aluminium alloy wire cloth, .45mm nominal dia of wire and average width of aperture 1.40mm and fixing with aluminium wire staples all complete as per requirement and direction of Engineering-in-charge

M& L for Double action floor spring hydraulically regulated made up of inimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed etc complete all as spd and directed

S&F 5 mm thick Aluminium composite panel of approved colour fixed to frame work or door etc complete all as spd and directed.

S&F Sheet glass black tinted /reflective 4.8 mm thick (of any tint) or fixed and complete all as specified and directed

S&F Sheet glass 4 mm thick (of any tint) or fixed and complete all as specified and directed

S&F in repair mild steel work in framed work such as grills, gratings , framed guard bars ,ladders etc,, with end of bars shoulders and /or riveted or forged into spikes , and similar work confirming to be Fe -290. Gde-E-165 complete all as specified and directed

M&L for preparation of new painted steel surfaces of any descrition, over 10cm width or grith ,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zine chromic primer complete all as specified and directed

S&F in repairs floor door stopper of aluminium alloy body and tongue in repair , anodised with hard drawn steel spring fixed in repair floor

Notes:- Tenderers may note that amount as given in schedule of credit will be deducted from the total amount to worked out the net contract sum at the time of Acceptance of tender.

Please Enable Macros to View BoQ information