SPL REPAIR TO FLOORING OF P 2 (JCO CLUB AND JCO LIVING ACCN, SM OFFICE /CONT ROOM AND VERANDA) OF CERTAIN MIL UNIT AND SPL REPAIRS OF 08 X TOILET BLOCKS IN BLDG NO P 25 OF CERTAIN MIL UNIT AT BINNAGURI UNDER GE (S) BINNAGURI

Amount

Taking down chowkats or frames n exc 1.5 Sqm (without taking off shutter from the frames) and removal from site complete all as specified.

Taking down chowkats or frames exc 1.5 Sqm n exc 4 sqm (without taking off shutter from the frames) and removal from site complete all as specified.

Dismantling floor hearth or wall tiling including cement mortar bedding (incl backing) removing serviceable tiles to store and rubbish off the premises complete all as specified.

Taking down cement plaster any description on brick or stone wall etc including racking out joints hacking for key scrubbing down with water etc complete all as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing on SI page No 156 of SSR Part-II complete all as specified.

S&F Solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specification and drawing on SI page No.160 of SSR Part-II complete all as specified.

S&F for pressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 105mm x60 mm x 1.25mm (thick)complete all as specified

S&F 30mm flush shutter, solid core construction, with block board core and plywood face panel, commercial type on both side etc complete all as specified.

S&F in repair factory made steel ventilator with top hung shutter including friction/ box type hinges ,steel peg stay complete including taking out old/unserviceable steel ventilator and making good to match as per existing surfaces etc complete all as specified.

S&F 250mm long aluminium anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section complete all as specified

M&L for 150 mm size aluminium anodised cast type handles complete all as specified.

S&F of 150mm long aluminium anodised,barrel tower bolt of extruded section complete all as specified.

S&F 100mm size stainless steel butt hinges medium weight complete all as specified.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar (1:6) finished even & fair complete all as specified.

M&L for rendering 20mm thick in cement mortar 1:4 in two layers of 10mm each using WPC in finishing layer on brick or concrete surfaces finished even & fair (WPC for finishing layer will be paid seperately as supply only) complete all as specified.

Supply only Liquid water proofing compound complete all as specified.

M&L for 5mm thick in CM 1:3 in ceiling finishing the surfaces even and smooth without using extra cement complete all as specified.

M&L applying two coats of weather proof exterior emulsion paint of standard quality and make ,over a coat of white primer including preparation of new wall surfaces with wall care putty complete all as specified.

M & L for complete removal of existing treatment and finishing the walls with two coats Acrylic smooth exterior emulsion paint of required shade for New work over and including priming one coat of exterior primer applied all as per manufacturer's specification and as specified.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or girth complete all as specified

M&L for three coat of white wash on walls on newly plastered surface incl preparation of surface complete all as specified.

M&L for applying three coat of white washing including preparation of new or previously untreated surface of ceiling complete all as specified.

M&L for complete removal of existing treatment of old plastered surfaces of ceiling and applying three coats of white wash all as specified .

M&L for prepartion of newly plastered surfaces of walls with wall care puty and applying two coats of oil bound distemper over a coat of primer complete all as specified.

M&L for complete removal of existing treatment of old plastered surfaces of walls prepared surface with wall care putty and applying two coats of oil bound distemper over a coat of primeretc all as specified.

Material and labour for preparing old steel surfaces and applying one coats of synthetic enamel paint complete.all as specified.

Material and Labour for preparing old wooden surfaces and applying one coats of synthetic enamel paint complete all as specified.

M & L for Virified Ceramic double charges tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in cement mortar 1:6 complete all as specified.

M&L Virified Ceramic tiles double charge light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match vertical surfaces, in skirting etc. set and jointed in neat cement slurry and pointed in whiter or coloured cement to match including 15 mm thick rendering in cement mortar 1:4 complete all as specified.

M&L for non-skid ceramic (400x400x7 to 8 mm thick) tiles set and jointed in neat cement slurry pointed in white or coloured cement to match in floor over 15mm thick screed bed in CM(1:6) all as specified.

M&L for glazed coloured ceramic tiles (350x450x7mm thick) on vertical surfaces such as skirting/dado set and jointed in neat cement slurry pointed in white or coloured cement to match over 15mm thick rendering in CM(1:4) all as specified.

S & F of 4mm thick figured glass pin headed type n.exc 0.5sqm each fixed to steel frame complete all as specified

Supply & fix in repair angular stop cock made of brass chromium plated screwed both ends for iron pipe for 15mm bore complete all as specified

Supply & fix in reapir Bib tap cast copper alloy, chromium plated with crutch or butterfly handle, screwed down for 15mm bore GI Pipe or for brass ferrule including taking down old unserviceable one complete all as specified.

S&F in repair of PVC low level flushing cistern, 10 ltr capacity, syphonic action type white body with inlet ball valve, float , handle, bracket, long flush pipe of PVC to suit flushing cistern ( long bend) etc complete & connecting to WC complete all as specified

S&F in repair tubular towel rail 20mm dia D type, Brass Chromium Plated 60 cm long between flanges complete all as specified.

S & F stainless steel soap dish best quality fixed to plugs with chromium plated brass complete all as specified.

S&F in repair of PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified.

S&F in repair Water Closet (squatt pattern) of vitruous china squatting pan of pattern "ORRISA" pattern size 580 x 440 mm white with integral foot rests (excluding flushing cirstern and flush pipe) including connection to trap and flushing pipe anti syphon pipe etc complete including trap set in and incl concrete complete all as specified.

M&L in repairs for PVC floor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1(diameter of outlet 110mm) as in repair complete all as specified

S&F in repair Vitreous China wash basin Pedestal pattern, white, flat back size 580x450 mm including cutting for and pinning in ends of brackets or erecting stand including waste pipe brackets, complete all as specified.

S& F in repair Vitreous China bowl urinal flat back, sizeof 465 x 355 x 265 mm white (minimum),with grating and union for discharge pipe, complete including providing and fixing plugs, bedding urinals gainst wall in cement mortar1:2, securing urinal to plugs withand including 60mmlong brassscrews, pointing around urinal back in cement; with brackets,flush pipe, grating and Union for discharge pipe complete all as specified.

S&F in repair of pillars taps,fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, scewed for iron pipe 15 mm bore complete all as specified

S&F in repairs for 15 mm bore stop cocks fancy type, chromium plated reduce body, long shank, cap (concealed type) screwed down high pressure screwed both ends for iron pipe or for union etc as in repair complete all as specified.

M&L Gun-metal, globe or gate valves,15mm bore with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified.

S&F in repair of swivel shower of CP with shower arm 150 mm size for fixing with 15 mm bore GI pipe complete all as specified.

S&F in repair for PVC (SWR) (Bore of pipe 110mm) pipes single socketed, in any length with rubber ring joints fixed to walls with necessary clamps, bolts etc complete all as specified

S&F in repair for PVC (SWR) bends any radius fixed to PVC Pipes/Steel Gutters etc complete all as specified (Bore of pipe 110mm)

S&F in repair for PVC (SWR) vent cowl fixed to PVC pipes/steel gutters etc complete all as specified (Bore of pipe 110mm)

Taking up or down steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc complete all as specified of following bore:-

Bore tubing 15mm complete all as specified

Bore tubing 20mm complete all as specified

M & L for steel tubing medium grade,galvanised fitting fixed complete to walls and ceiling or floor complete for this following.

Bore tubing 15mm complete all as specified

Bore tubing 20mm complete all as specified

Material and labour for hoisting and fixing rotational moulded polyethylene(double layer) water storage tanks 1000 lit capacity (Cylinderical vertical), ISI marked(IS-12701:1996) hoisted and fixed in position including inlet, oulet, over flow connection, ball valves etc complete all as specified.

S&F in repair 20 mm dia PVC ball cock (PVC float valves) complete high pressure with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed as required to use reducer and check nut complete all as specified.

M & for water proofing treatment to sunken floor with the following course of treatment/ specification: (i) Cleaning top surface of floors /slabs and laying 50 mm thick (avg) PCC of grade M10 (Nominal mix) , mixed with WPC as per manufactrrer's instruction laid in slope 1:20 towards spouts including coveting corners (ii) 15 mm thick plastering in CM (1:4) on sides mixed with WPC as pe rmanufacturer's instruction. (iii) Applying 1st layer of slurry @ 0.488 kg / sqm mixed wth acrylic based polymer modified cementious compound @ 0.253 kg /sqm This layer shall be allowed to air cured for 4 hrs. (iv) applying 2nd layer of slurry @ 0.242 kg/sqm mixed with accrylic based polymer modified cementenous compound @ 0.126 kg/sqm.This layer shall be allowed to air cured for 4hrs followed with water curing for 48 hrs.(v) Applying a coat of industrial bitumen 85/25 penetration @ 1.50 kg/sqm on plastered and concrete surfaces (vi) Providing 150 micron thick polyutethene paint in two coats (each of 75 micron measured dry on dry surface over a coat of PU primer including preparation . (Make of PU primer - Dek guard EP -302 of M/S Fosroc or equivalant approved brand.Make of PU paint - Dek guard PUor equivalant approved brand. (vii) 2 Nos 32mm bore GI medium grade 450mm long spout ,to be provided through external wall to drainout accumulated water.(vii) Sunken floor shall be tested for water tighness by filling water for 72 hrs before and after treatment work is carried out and ensure that no leakage /seepage exists (ix) Sunken portion shall be filled with lean concrete of grade M7.5 stone agreegate

Demolition & breaking up drain pipes( salt glazed ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe 150mm

Excavation in trenches n.exc 1.5 in deep and n.exc 1.5 m wide for foundation etc not exc 10 sqm on plan and getting out in soft / loose soil

Demolition of precast block masonary / Brick work or precast concrete article built in cement mortar complete all as specified

Demolition of reinforced cement concrete of any description and in any position such as precast manhole cover or cover slabs of septic tank etc (reinforcement cut as required to facilitate demolition)

M&L for precast RCC 1: 2 :4 type B-1 using 20mm graded aggregate set in cement mortar 1:4 as in manhole covers including necessary formwork complete all as specified

S&F for PVC (SWR) (Bore of pipe 160mm) pipes with working pressure 6 kg/cm2 single socketed, in any length with rubber ring joints fixed to walls with necessary clamps, bolts etc complete all as specified.

M&L for mild steel TMT bars 6mm to 8mm dia cut to length , bent to shape required, including cranking , bending and binding with MS wire , not less than 0.9 mm dia or securing with clip complete all as specified.

M&L PCC 1:3:6 type C-2 (40mm graded aggregate) as in foundations, filling and mass concrete complete all as specified.

M&L PCC 1:3:6 type C-2 concrete bed to drain pipes including packing under & haunching against the sides of pipes after they are laid & tested dia of pipe 150mm complete all as specified.

Returning ,filling in , including spreading , levelling , watering and well ramming in layer not exceeding 25 cm thick in soft/ loose soil complete all as specified.

Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified.

M&L cutting into existing manhole for connecting new drains making good to pipe and rendering cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished & reforming benching as required dia of pipe 150mm complete all as specified.

M&L for brickwork with burnt fly ash old size bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete.

Taking town of steel windows/ventilators of any size and description and removal from site complete all as specified.

Providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories.(Area not exceeding 2.00 sqm)

S&F 4.8 mm thick sheet glass ordinary quality and glazing with oil putty/ wooden beading in square exc 0.5 Sqm in each panecomplete all as specified.

S & F aluminium frame for partition, doors, windows, ventilators with one or more rebates including joining cleat for fixing etccomplete all as specified. Make of aluminium section – JINDAL/ INDAL/ HINDALCO

S&F aluminium door shutter, aluminium section weighing minimum 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles (02 Nos) in each door, hinges, anodised aluminium snap beading, screws etc,complete all as specified. Make : Make of aluminium section – JINDAL/ INDAL/ HINDALCO

S&F mortice lock, brass, 4 levers type, size 100mm complete all as specified.

S&F floor door stopper of aluminum alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor but of brass body and tongue with hard drawn steel spring (Overall length of cover plate 140mm) fixed in repairs etc complete all as specified.

S&F in repair Aluminium Die cast body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified.

S&F framed work such as grills, gratings etc with end of bars, shouldered and/ or rivated, or forged into spikes; framed guard bars, framed work for door and windows, railing and similar work confirming to Fe 290 Gde-E-165, Complete all as specified.

Dismantling wall and ceiling board (fibre pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified.

Supply and fixing as in repairs for aluminium anodised snap grid (605X605mm size) to support the boards / tiles with aluminium Tee section 35 mm x 25 mm x 1.40 mm, cross Tee 23.50 mm x 23.50 mm x 1.40 mm and aluminium angle 25 mm x 25 mm x 1.40 mm as on edge / sides including proper hanging arrangement with 4 mm dia anodized galvanised iron wire with false ceiling iof 4 mm thick E board classic for insulation and accoustic purposes of size 600X600 mm fixed with necessary accessories to frame work or with staples on snap grid upto ceiling proper scafolding arrangementsand with complete all as specified.

-----Blank-----

Taking down tarfelt incl cement mortar bedding from roof surfaces and lowering and removing the same to a distance exc. 50m and n. exc. 100m incl roughening of old concrete surface of roof by wire brushing and cleaning the surface to remove all loose dust etc complete all as specified

M&L 25 mm thick PCC 1:2:4 type B0 (Using 12.5 mm graded stone aggregate) mixed with water proofing compound and laid on RCC slab as base layer for roof treatment roughening the top surface of concrete by using broom sticks while the concrete is green complete all as specified.(NOTE : water proofing compound paid separately under relevant item of this Schedule 'A').

M & L for water proofing treatment to RCC roof slab as specified below complete all as specified. (a) 10 mm th cement plaster in CM 1:4 with integral WPC to be laid over the RCC roof slab when the concrete is green. (b) Applying a uniform coat of bitumen primer @ 0.70 kg/sqm over cement plaster. (c) 3 mm thick plain texture and weighing not less than 3.5 kg/sqm Atactic Polypropylene Polymer (APP) modified bitumen based prefabricated five layer water proofing membrane reinforced with non woven polyster matt black finished over compatible primer at 0.4 Ltr / sqm of density at 25 degree centigrade 0.87 - 0.89 kg/ltr and viscosity 70-160 cps or cold sticker and torch application of membrane with overlap while torching shall be 150 mm on length side and 100 mm on width side. after necessary preparation of surface complete as per manufacturers instructions. (d) Apply two coats of bitumastic - aluminium paint over the membrane.

M&L for PCC type C-2, 1:3:6 (40mm graded aggregate) 75mm thick as in plinth protection, pavement etc and finished the surface even and smooth without using extra cement complete all as specified

Dismantling of Concrete in ground floors and pavings n exc 15 cm thickness any description complete all as specified.

M & L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulderscomplete all as specified.

M&L for 75 mm thick cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in path /steps laid with and incl use and waste of form work and finishing the surface even and rough to receive the topping layer or tiling complete all as specified .

M & L 60 mm thick M-30 grade factory made vibratory compacted cement concrete rubber moulded, interlocking paver block any shape and size confiroming to IS 15658-2006 with grey cement and pigment as approved laid over and incl 50 mm thick consolidated sand cushion and joints filled with sand complete all as specified.

M & L for PCC 1:2:4 type B-I ,(using 20 mm graded stone aggregate) as. in coping /benching to sides of foot path fininished fair and even including necessary formwork etc complete all as specified.

M & L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors and pointed in with grey pigment cement and pigment including 15 mm thick screed bed in cement mortar 1:6 complete all as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified.

M&L for point wiring complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated, IS 694 unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less than 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sunken terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes duly painted with anticorrosive paint, concealed in walls with bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screws for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sunken for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications all as specified :- (a) One light point controlled by one way switch 5/6 amps complete all as specified.

All as per Item No 92, One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps complete all as specified.

All as per item No 92 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified.

S&F switch piano flush type 5/6 amps single pole one way complete all as specified.

S&F of socket outlet 2 in 1, 5 Pin, 5/15 amp, multipurpose 230 volt flash type complete all as specified.

S&F switch piano flush type 15/16 amps single pole one way complete all as specified.

S&F Ceiling rose, surface type with back plate, three terminal /PVC/ polycarbonate, isolated body complete all as specified.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp,IP 20, class I, wall/ surface mounted, luminaire efficiency not less than 100 lumens/watt, power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz including connecting up with three core flexible copper conductor cable of suitable size complete all as specified.

Taking down carefully Exhaust fan from its original position and refixing / hanging after B/R plaster work complete all as specified.

Taking down carefully Water heater Geyser from its original position and refixing / hanging after B/R plaster work complete all as specified.

S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), double door, single pole & neutral with minimum 100 amps rated bus bar, IP-43 protection suitable for fixing MCB"S/lsolators complete including provision of blanking plates as required and taking down the old one complete all as specified.

S&F MCB, Single pole & neutral 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified.

S&F MCB, Single pole, 6 to 32 amps, 240 volts, ‘B’ curve, 10 KA all complete including taking down the old one complete all as specified.

Material and labour for concealed sub-main wiring alongwith earth wire of size of 2 x 4.0 sq. mm + 1 x 4.0 sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of of size not less than 25 mm with all fittings and accessories ISI marked including cutting chases for conduits where as not feasible in ceiling or beam making provision to fix on surface with saddles and making good to walls, floors etc complete, including taking down old unsv aluminium submain wiring all as specified. NOTE : Two runs of 4 sqmm conductor for main and one run of 4 sqmm conductor as earth wire with proper colour coding including one run run of PVC conduit shall be measured as one unit length. Connections of cables wit MCBs or bus bar shall be done through appropriate size brass/ copper thimbles

M/S DELTA ENGINEERS & CO (BID ID -3365687)

SHRI MANOIRANJAN BISWAS (BID ID -3366756)

M/S PLABAN KUMAR GOPE (BID ID -3365356)

L. B. SHARMA (BID ID -3365327)

SS SHARMA (BID ID -3367328)

M/S RATNESH KUMAR SINGH (BID ID -3366784)

M/S MOHAN KUMAR BANSAL (BID ID -3363823)