1155/2024/E1-Differently abled person welfare scheme 2024-25 - Additional Work for One Stop Centre at Old Office Buiilding in Musiri Municipality.

Amount

Earth work excavation for foundation in all type of soils as may be directed except in hard rock requiring blasting and also including refilling the sides of foundations with excavated soil in layers of 15cm thick well rammed and consolidated and depositing the surplus earth within the compound in places shown by the departmental officers with initial leads and lifts and clearing and levelling the site etc., complete complying with the standard specification, drawing and as directed and as directed by departmental Engineers, with initial lead of 10m and lift of 2mts.

Supplying and filling in foundation and basement with filling M sand in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification and directed - 10 m 2 (P & D)Data 38

Plain Cement concrete of mix 1:2:4 (One cement two sand and four aggregates) using 20mm gauge hard broken including cost conveyance of all materials to site including labour charges, transporting and placing in position including shoring, strutting Etc Complete Complaying with standared Specification

Providing and laying ,spreading and compacting graded stone aggregate to wet mix macadam (WMM ) soecification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.

Supplying and laying Rubberised interlocking Paver block M40 grade Providing and laying of 83mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40 N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with sand cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, Stone Dust cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12 mm thick PLB board and 5.5 mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on both sides,floor stopper,Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections.All the materials should be got approved by the Engineer - In -charge before fixing as directed.

Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12 mm thick PLB board and 5.5 mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on both sides,floor stopper,Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections.All the materials should be got approved by the Engineer - In -charge before fixing as directed.

Supply and fixing Perculated gypsum board false ceiling using 18 mm thick of approved Quality and design suspended from the ceiling using ‘U’ shaped Galvanised Iron channel of size 25 x 25 x 0.55 mm thick at 1.20 M centre to centre on both longitudinal and cross direction for vertical support and fixing ‘U’ shaped G.I. Channel of size 50 x 30 x 0.55 mm thick at 0.60 m centre to centre on cross direction and fixing of ‘U’ shaped G.I. channel of size 50 x 10 x 0.55 mm thick at 0.90 m centre to centre on longitudinal direction respectively for horizontal support by using T.W. reapers at corners and at intermediately and fixing of plaster of paries on the panel provided as per design/pattern given by the site officer and finishing the ceiling surface with some plaster of paries materials etc. Necessary openings should be made for providing spotlights, florescent tubes in the ceiling by using kit ply 12 mm thick and opening should be covered with Acrylic panel etc. complete complying with standard specification and as directed by the dept officers. All the materials should be got approved before use work.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Wiring With 2x1.5 Sqmm (22/0.3) PVC Insulated Single Core Unsheathed copper conductor cable of 1100 V Grade in Suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T switch With Continous earth wire connection of 14 SWG TC Wire for making good of the concealed portion with asuitable colour For Pvc Conealed light Point/ Fan Point (ForElectronic regulator ).etc ,Complete as Per Standard Specifications

Supply and fabricating,Eteacting Structura Steel work for Roofing Welded Or bolted type using MS channels,angles,plate and round bars etc.,Conformong To IS Specifiction incliding primer coating and enamal painting as per design given by the departmental Officers etc., Complete as per Standard Specification.

Fabricating Supplying and Fixing of pre painted galvanium iron sheets with the following Specification. The Materials should be of PPGI tile profile with a red colour or any other approved design 0.47mm thick 24 guage having width 1050mm.Thw sheet should be G.I base pre painted hot dipped galvanized iron sheet and to be fixed with shelf taping screws,plastic washer.etc.,Complete

Providing Name Board

C SUBRAMANIAN (BID ID -1154091)