Supply, Installation, Testing and Commissioning SITC of Electro Mech machineries at Katariya (Kalawad Road and 2nd Ring Road Junction) UB Pumping Station with 05 Years Comprehensive Operation & Maintenance

physical submission of required documents. Technical bid must be submitted by

RPAD/Speed post only.

Office of the Dy Executive Engineer (Mech)

Rajkot Municipal Corporation,

Dr. Ambedkar Bhavan,

Central Zone Office,

Water Works, Room No.6,

Dhebar Road, Near ST bus stand,

Pre-Qualification Criteria:

Financial Criteria:

1. The bidder must have achieved a minimum annual turnover in any one year over the last

seven financial years (i.e. 2024-25 to 2018-19) of the annual value of contract applied for.

(i.e.,Rs.1,71,01,550/-)(Rajkot Municipal Corporation’s Enhancement Factor can be

2. The bidder has liquid assets (aggregate of Working capital, cash in hand and uncommitted

bank guarantees) and/or credit facility equal to 25% of the contract value. (i.e.

3. Available Bid Capacity-ABC must be more than the tender amount.

Note:- The estimated cost of the work is Rs. 1,71,01,550/- for one year for the purpose of

calculation of Annual turnover and Working capital.

B) Experience Criteria:

1. The bidder has successfully completing or substantially completing at least one contract of

similar nature of work at least 40% of the value of proposed contract within the last seven

years. (i.e. Rs.68,40,620/-)

2. Substantially completed works means those works which are at least 90% completed as on the

date of submission (i.e. gross value of done up to the last date of submission is 90% or more of

the original contract price.) and continuing satisfactorily. Experience certificate of competent

authorities required to be submitted Only 3(A) CERTIFICATE will be considered as

experience certificate and sign not belongs to executive engineer.

Note:- Experience as a contractor of similar nature of work

The physical submission must be accompanied by a EMD of Rs. 1,71,020/- as well as e-

tender fee (non-refundable) of amount of Rs.4500/- in terms of Demand draft in favor of

Municipal Commissioner, Rajkot Municipal Corporation, Rajkot, from any Nationalized Bank or

as per Finance Department, GR No.-FD/MSM/e-file/4/2024/2859/DMO, Dt.01/05/2025 and

must be delivered within seven days from the last day of submission of bid. The bid security

and tender fee must be included with the physical submission on address below by RPAD only:

Addi. City Engineer

Water Management Unit (Hand Pump)

Room No.06, Dr. Ambedkar Bhavan,

Central Zone Office, Dhebarbhai Road,

Rajkot Municipal Corporation

The bidder also can pay EMD and Tender fee by NEFT/RTGS or Online Transfer.

RMC BANK ACCOUNT DETAILS

A/C No.: 015305010638 Bank Name: ICICI Bank

IFS Code: ICIC0000153 Branch: Jay Hind Press

Following documents shall be submitted in original at above Address by RPAD only:

Following documents shall be submitted in electronic format through online by scanning And In Hard

copy Only Tender Fee, EMD and Tender Document(Technical Bid, Price Bid and Corrigendumm) also

with duly sign and stamp of Agency at above Address by RPAD.

: The required documents to be submitting online on website https://rmctender.nprocure.com

3. Tender Documents (Technical bid, Price Bid and Corrigendum)

4. GST No. Details

5. PAN No. Details

6. PF and ESIC Details

7. Professional Tax Details -Enrollment certificate(Firm) and Registration certificate (Employee)

8. Class Registration Certificate

9. Work Experience Certificate- Only 3(A) CERTIFICATE will be considered as experience

certificate and sign not belongs to executive engineer

10. Power of Attorney (if Applicable)

11. Current Electrical Contractor License

12. Turnover Details of last seven years

13. Working Capital Details

14. No Blacklist Affidavit on Rs. 300/- Stamp Paper with notarized as per tender format.

15. Sites visit & fully aware with nature of work confirmation letter

Terms & Conditions:

1. Tenderer has to submit tender documents online at https://rmctender.nprocure.comand Submit

Hard copy of tender fee, EMD, signed tender copy only on address given above by RPAD only:

2. Conditional tender are liable to be rejected.

3. Joint venture or MOU is not permitted.

4. The bidder should provide accurate information on any litigation history or arbitration resulting

from contracts completed or under execution by him over the last ten years. This should also

include such cases, which are in process/progress. A consistent history of awards against the

bidder may result in failure of the bid. In case the bidder has not provided such information and

has come to the notice of the authority, the tender will be rejected at what so ever stage and in

such case all the losses that will arise out of this issue will be recovered from the

tenderer/bidder and he will not have any defense for the same.

5. Enhancement factor at 10% per year for last seven years will be applicable to arrive average

annual turnover and finalize the magnitude of work done in last seven years.

6. The Bidder / firm must have current Registration in E1-Class or Above(R & B) with of any State

Government / Central Government authority.

7. The agency should not be Black Listed/Debar/Terminated anywhere in India, for which, agency

will have to submit fresh Notarized Affidavit on Rs.300/- judicial stamp paper.

8. Sites visit & fully aware with nature of work confirmation letter

9. Power of Attorney authorizing the person for signing the Tender and give any clarification

asked by department.

10. The agency shall also have to submit the documentary evidence for possessing the Current

Electrical Contractor License in Electrical Department of Government.

11. The contractor shall have to purchase the material required for this tender work, only from the

supplier having registered GST Number. RMC will not be responsible to pay any amount

towards GST if the material is purchased from the unregistered supplier / not having GST

12. Also, the details of works on hand and works completed shall have to be mentioned in the

Annexure-II of Technical Bid (Volume-I)

13. The successful bidder shall have to pay security deposit amounting to 5% of Contract Value in

favour of "Rajkot Municipal Corporation" in terms of Fixed Deposit Receipt of Nationalized

Bank or as per Finance Department, GR No.-FD/MSM/e-file/4/2024/2859/DMO,Dt.01/05/2025

valid for the period of 30 Months.

If the contract price offered by the selected bidder is lower than 10% but up to 20% of

the Estimated project Cost than the additional performance security shall be calculated @20%

of the difference in the Estimated Project Cost minus 10% of the Estimated Project Cost and

Contract Price offered by the selected Bidder.

If the contract price offered by the selected bidder is lower than 20% of the Estimated

project Cost than the additional performance security shall be calculated @30% of the

difference in the Estimated Project Cost minus 10% of the Estimated Project Cost and Contract

Price offered by the selected Bidder.

The Additional Performance Security shall be treated as part of the Performance

Security. The Performance Security shall be valid beyond 60 days of the defect liability period

and the additional Performance Security shall be valid beyond 28 days of Project completion

14. The Tender of those bidder(s) those who fails to submit the required documents physically

within the stipulated date and time, will be treated as non responsive and their Price Bid will

15. After opening of Technical Bid, the procedure for the pre-qualification shall be adopted and the

Price Bid of only successful qualified bidder shall be opened for final evaluation of the contract.

The decision of Municipal Commissioner regarding the pre-qualification shall be final and

binding to all the bidders.

16. After opening of the Technical Bid, if the agency is disqualified for this work and under such

circumstances if the agency tries to pressurize the Evaluation Committee through any means

then the offer of such bidder will be treated non-responsive and liable to be rejected out rightly

without assigning any reason thereof.

17. Enter into an agreement on stamp paper as per prevailing norms. It shall be incumbent on the

Contractor to pay the stamp duty and the legal charges for the preparation of the contract

18. The Jurisdiction will be Rajkot City only.

19. Commissioner, Rajkot Municipal Corporation, Rajkot, reserves the right to accept / reject any or

all e-Tender(s) without assigning any reasons thereof.

Add. City Engineer

Water Management Unit

Rajkot Municipal Corporation

Supply, Installation, Testing and Commissioning (SITC) of Electro‐Mech

machineries at Katariya under bridge with 05 Years comprehensive

Operation and Maintenance.

1 Bill of Quantities (General)

2 Information to Tenderer

3 Commercial Conditions

1.0 BILL OF QUANTITIES (GENERAL):

The Bill of quantities consists of following section:

1.2 Supply items (Mechanical , electrical)

Erection Items ( Including storage , installation testing and

commissioning of pumping machinaries with accessorieses)

The bill of quantities forms the most important part of the tender

documents. The supply, installation and Commissioning of various

equipments which form a part of total work are indicated in the schedules

separated included in this documents. The tendering contractors shall price

each of the item of this document separately.

Each item in the bill of quantities is to be individually priced in in k and the

same should be added up to the tender sum. No column in the bill of

quantities shall be left blank. The description of the works given here is only

for guidance and all relevant clause must be consulted. The contractor's price

must allow for all works as per the detailed specifications and for all

contractual obligations whether separately specified or not.

1.1 SUPPLY ITEMS:

The supply items (Mechanical-Electrical)

As mentioned in the tender document.

1.2 ERECTION ITEMS: -

Erection testing and Commissioning :

The bill of quantities for storage, installation, testing and commissioning of

the pumping machineries, It also includes provisions of contractors

equipments/machinery, power cabling etc., complete.

This shall also include:

I Performance testing and maintenance.

II Ten days trial running and maintenance.

In case the tendering contractor given alternative design, a separate bill of

quantities on exactly similar lines as in this tender shall be acceptable.

Tenderer may modify description of the items to suit his alternative offer

without changing the format.

1.4 The bill of quantities, general conditions of contract and the specifications

which from an integral part of this contract shall be read in conduction.

1,5 The rates and prices in the bill of quantities shall except in case separately

provided for, be deemed to cover all the contractual obligations including GST

under this and above quoted documents which require the setting of the works

for satisfactory performance.

BILL OF QUANTITY

NAME OF WORK: Supply, Installation, Testing and Commissioning (SITC) of Electro‐Mech machineries at

Katariya under bridge with 05 Years comprehensive Operation and Maintenance.

PART – A (SITC)

Item Decription Qty. Unit Rate in Rs. Amount in Rs.

MECHANICAL WORK

1 SEWAGE SUBMERSIBLE NON CLOG PUMP-MOTOR SET 5 Ea. 533453.00

Supply, installation, testing and commissioning of non clog sewage

submersible pumnp with SS CF8M Impeller, CI Casing to Gr 260,SS

410 shaft suitable for 3 Phase, 415 V, 50 Hz., AC supply submersible

motor having Class 'F' insulation with temperature rise limit to

Class "B" and IP-68 protection.

The scope shall include all required accessories pump viz. If req. SS-

304 heavy duty & of suitable size double guide pipes of length to

suit the sump height with required supports, SS-304 or suitable

stainless steel grade Chain with shackles (shall be with dual hook /

shackles of 150 mm or suitable higher size at app. every 1.5m C-C

distance) & of length as per sump height + min. 3m, Check valves,

sluice valves, pressure gauge, automatic coupling device, delivery

bend suitable to install pump set in new sump, thrust block, .

Submersible Power & control cable upto starter panel through

suitable size GI pipe (copper flexible & stranded type conductor of

reqd. cores & size for each pump motor set) & of length sump

height + min. 15 m long each run with necessary electrical

termination connection at junction box / starter panel.

The pump set shall be provided along with automatic shut down

arrangement when water level in sump go down to the minimum

water level (MWL)

The scope also includes providing civil foundation for duck foot

bend for auto coupling etc & any other required minor civil

modification /rectification /thrust blocks/finish work to complete

Pump Capacity : Discharge 360 m3/hr, Head: 16 m, ( 4W + 1S ),

Overall Efficiency at Duty : 70 %, delivery pipe size 200mm dia

Motor Rating: 30 HP / 22.5 kW (or higher rating as reco. by pump

Make: KIRLOSKAR, KSB, JASCO, KISHOR, PULLEN, AQUA.

2 MOTOR CONTROL PANEL OR STARTER 5 Ea. 23809.00

Supplying & erecting approved make motor control cubical panel

[Star delta] made from 16G CRCA sheet duly epoxy powder painted

inside and outside with hinged doors and locking with suitable size

of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and

current meter (in a single unit) with micro controller based control

unit and current sensing single phasing preventer electronic

overload protection, PMJ, Capacitors, over voltage (Programmable)

protection and under voltage (Programmable) protection, prod less

dry run protection programming facility for setting of all parameter

like overload current, high voltage limit, low voltage limit, dry run

limit with digital indication on seven segment LED display for any

fault like over load, high voltage, low voltage, dry running single

crimped, electronic star delta timer, feather touch start / stop push

buttons to be erected on angle iron frame. Grouted on wall the

contactors will be of L& T, Siemens , BCH make only).. The starter

shall matcch GWSSB standard specification for 30 HP non- clog

pump notor set.

Make :L&T,Siemens, ABB. schniders, switchgears.

3 SEWAGE SUBMERSIBLE NON CLOG PUMP-MOTOR SET 3 Ea. 302528.00

Supply, installation, testing and commissioning of non clog sewage

submersible pumnp with SS CF8M Impeller, CI Casing to Gr 260,SS

410 shaft suitable for 3 Phase, 415 V, 50 Hz., AC supply submersible

motor having Class 'F' insulation with temperature rise limit to

Class "B" and IP-68 protection.

The scope shall include all required accessories pump viz. If req. SS-

304 heavy duty & of suitable size double guide pipes of length to

suit the sump height with required supports, SS-304 or suitable

stainless steel grade Chain with shackles (shall be with dual hook /

shackles of 150 mm or suitable higher size at app. every 1.5m C-C

distance) & of length as per sump height + min. 3m, Check valves,

sluice valves, pressure gauge, automatic coupling device, delivery

bend suitable to install pump set in new sump, thrust block, .

Submersible Power & control cable upto starter panel through

suitable size GI pipe (copper flexible & stranded type conductor of

reqd. cores & size for each pump motor set) & of length sump

height + min. 15 m long each run with necessary electrical

termination connection at junction box / starter panel.

The pump set shall be provided along with automatic shut down

arrangement when water level in sump go down to the minimum

water level (MWL)

The scope also includes providing civil foundation for duck foot

bend for auto coupling etc & any other required minor civil

modification /rectification /thrust blocks/finish work to complete

Pump Capacity : Discharge 100 m3/hr, Head: 16 m, ( 1W + 1S ),

Overall Efficiency at Duty : 70 %, delivery pipe size 150mm dia

Motor Rating: 12.5 HP / 9.63 kW (or higher rating as reco. by pump

Make: KIRLOSKAR, KSB, JASCO, KISHOR, PULLEN, AQUA.

4 MOTOR CONTROL PANEL OR STARTER 3 Ea. 13658.00

Motor control panel or fully automatic star-delta starter with

necessary electrical connections and electrical control panel with

starter overload relay range 13-21 ampere including individual

MCB, analog volt meter with selector switch, analog ampere meter

with selector switch, SPP, PMU, capacitors, phase indicators, as

well as digital meters as per GWSSB standard specification for

HP non- clog pump notor set.

Make :L&T,Siemens, ABB. schniders, switchgears.

5 MONORAIL EOT WITH ELECTRIC CHAIN HOIST 1 Ea. 440250.00

Supply, installation, testing, commissioning of Electrically operated

Chain Hoist & Electically operated geared trolley suitable to

operate on Mono Rail Girder having motorized motion in vertical

liftingg & for cross travel, manufactured as per IS:6547-1972-Class

II & IS-3177- Class-II, complete with electrically operated chain

hoist & Electically operated geared trolley, brake, chain-gear,

motors, safety device, pendant push button, starter panel, cables

from motor to starter panel and all other required accessories like

limit switches, panel, power supply system (Fastoon cable

type),fasteners, epoxy painting, etc. tested to 50% over load,

complete and as per specifications.

Note: Capacity of Electric CPB hoist shall be minimum as specified

or min.1.5 times the weight of single heaviest component to be

lifted at Pump location whichever is higher.

Capacity: min. 1 Ton. As required

Lift: 15 m. (min) , Span 9 m to 12 m or as requried, Long Traves

Mtr or as requried, Make:- Morris / Indef/ Safex / WH Brady

/Anker/ Max/ Japs

6 Manufacture supply and delivery, lowering & laying of submerged 8000 Kg 137.00

arc welded M.S pipe out side coated with best quality Bituminus

Paint with Epoxy coating to inside pipeline with two parts of

Solvent free high build liquid epoxy lining as per AWWA C210-07

suitable for portable water application & shall be approved by

CFTRI India/BS 6920-UK/international standard/NSF/ANSI/-61

to be fit for contact with portable water for consumption with

micron thickness, having a beveled ends plate and coil conferming

to is 3589-2001 or its latest revision /ammendment for following

thickness including all taxes, transportation, freight charges, octroi,

inspection charges, loading, unloading, conveyance to

Departmental stores/ site, stacking, etc. including specials and

wastage etc.; complete Tender

Specifications: Make:- Essar / Tata / Jindal / SAIL/ Zenith / Asian

7 M.S. specials plain/ Flanged ended 1150 Kg 137.00

Erection, Installation, Testing & Commissioning of M.S. Specials for

Delivery, By Pass & Header Piping with Flanges, eccentric Nozzles,

Nut-Bolts, Y -tee connection, puddle flanges etc. Complete. Up to

8 Providing , erecting , fabricating the M.S. structure as per 5250 Kg 137.00

requirement on site incorporating proper size of M.S. angles, flats,

bars, channels, sections complete with cutting, welding, grinding &

finishing duly painted with one coat of red oxide with erection on

site as per direction of engineer in charge with necessary grouting,

cementing, plastering & finishing complete. (For Covering Cutout

9 Providing , erecting , fabricating the M.S. structure as per 5000 Kg 137.00

requirement on site incorporating proper size of M.S. angles, flats,

bars, channels, sections complete with cutting, welding, grinding &

finishing duly painted with one coat of red oxide with erection on

site as per direction of engineer in charge with necessary grouting,

cementing, plastering & finishing complete. (For Making Stair

D Electrical Panel

10 Supply, Installation, Testing and Commissioning of Electrical Panel 1 Ea 300211.00

manufactured as per IEC 61439 as per Following

Construction 14 SWG MS CRC Sheet Type 2B construction

Incoming Changeover -400A FP Auto changeover Switch

MCCB - 400A FP, Micro Processor Type With E/F protection, SPD

Outgoing MCCB - 8 Nos 80A FP, Variable TM type MCCB-2Nos, 63A

FP, Variable TM type MCB - 4 Nos 32A C Curve Busbar : 400A AL

PVC Sleeved with 0.8A Current Density Digital Ammeter Digital

Voltmerer Indicating Lamps-12 Nos.

Capacitor Bank:

Outgoing 160A MCCB, from

Ougoing : (5+10+20+20+20) KVAR 550V APP Capacitors with

Detuned reactors

8 Stage APFC relay, timer contactor, Indicating Lamp A/M Switch

etc as required Switchgear Make : L&T, Siemens, Schneider

11 Design, Supplying, installing, testing of factoryfabricated ready 1 Ea. 216103.00

made Three phase APFC Panel Cubical Panel fabrication should be

type tested as per IEC 61921, 61439:1&2 Capacitor Duty Contactor

for switching as per following Steps Incomer Switch of MCCB type

Icu=Ics=50KA at 400/440 Volts, with OC, SC, internal earth fault

protection Incomer Switch of MCCB type Icu=Ics=50KA at 400/440

Volts, with OC, SC, internal earth fault protection, Copper tinned

insulated Busbar, Cubical panel should be indoor type with IP

and IK 10,Metalized polypropylene film tye3-phase 550Volt

Capacitor, De tuning Reactor for each capacitor, Panel having Short

Circuit and Overload protection, Each step Capacitor having

suitable MCB with Sc, OL, internal earth fault relay, Each stage

having Stage Contactor (Capacitor load rating), A/M switch, PF

regulator master controller having suitable steps with LCD

display, Rs 485 Communication port, Indication LED Lamps for main

incomer and ON-OFF for each capacitor bank, MS Chanel for

Floor mounting, Cable entry as per site situation,Cooling fans for

12 Supplying rubber matting of 12mm thickness as per IS:15652/IEC 20 Sqmt 3051.00

13 Follow Up with supply co. for getting supply . The scope also covers 1 Ea 15000.00

laying of L.T. cable from Meter to MCCB. This also covers to obtain

any permission required for road crossing from any authority (if

required), Filling the necessary application to supply co., following

up and getting the supply filling the necessary test report to the

supply co. All official fees shall be paid by client on presentation of

documentary proof and all other out of pocket expenses shall be of

14 CHANGEOVER SWITCH 1 Ea. 26231.00

Supply of Approved make Iron Clad or metal clad four pole change

over switch 415V. confirming to IS in sheet steel enclosure of

following capacity and Erection on New angle iron frame duly

painted with red oxide .

Rating: 400 A Cat-lll

Providing and erecting Approved make Four pole moulded case

circuit breaker having breaking capacity ICU of 50 KA and above at

415 V having Normal current rating 400A. with micro processor

based release suitable to work on A.C.supply 50 c/s. With all

internal connections, spreader tinned copper & complete erected

with supply of 16 G.M.S. housing.

ICS=100% of ICU only Cat III

Make :L&T,Siemens, ABB. schniders, switchgears.

16 Supplying and erecting, commissioning and testing of Diesel

Generating set confirming to IS: 4722:1968 & BS:5514 having

continuous rating, 3 phase, 415 volts, 50 cycles A.C. supply

comprising of a totally enclosed air/water cooled diesel engine

with multi-cylinders developing suitable BHP not less than

following capacity at 1500 RPM with 10% overload for one hour in

24 hours with standard accessories like fly wheel, lubricating oil

cooler, "A" class governor, heavy duty fuel wheel and lubricating oil

filter, oil bath air filler, lubricating oil pressure gauge, end exhaust

manifold, standard set of tools with adjustable spanners, screw

drivers, cylinder head to cover, joint cylinder head to exhaust,

element lube oil filter, 12 / 24 volts electric starting equipment

complete with standard heavy duty battery, dynamo, cut-outs,

ammeter, necessary wiring, pressure gauge, starter etc and heavy

duty Residential type exhaust silencer (With DEF System) and

vertical hot air duct both

logged with asbestos rope, save oil trays, exhaust piping of

required length, standard wall/floor mounted fuel with level

indicator and piping and drip proof alternator, self excited, self

regulated, screen protected, with excitation system, capable of

delivering the rated system output at 415 volts, 3 phase, 0.8 PF,

Hz, 4 wire, running at 1500 RPM, conforming to IS-4722- 1968 with

voltage regulation +/- 5% of rated voltage from no load to full

load. Both the engine and alternator fitted on a common

fabricated steel base plate with antivibration mounting engine

and alternator both connected to each other by flexible flange

coupling and with floor/wall mounted control panel box

comprising of voltmeter ammeter, selector switches, ACB / MCCB

/ MCB of adequate capacity,

indicator lamps duly wired with HRC fuses. The alternator & 1 Ea. 1574322.00

control panel shall be connected with provided suitable capacity

armoured cable and complete with Acoustic enclosure (canopy)

made out of 16 SWG CRCA Sheet, sound absorbing material

Rockwool of 64 density & 100 mm thick conforming to IS:8183 / PU

Foam of 40 Density - at least 40 mm. The resin bonded rockwool

covered from inside the canopy by perforated sheet with 3/4 mm

holes, sound level not more than 75 dB at a distance of 1 mtr, as

per PVCT norms.DG set should have in built fuel tank capacity of

minimum 8 hrs of continous running capacity on full load .

Erection, commissioning and satisfactory testing as per

requirement with first filling of fuel (minimum up to the 80% of

fuel tank capacity), oil, etc. with guarantee / Warrantee of

complete system for Two years. & with obtaining all necessary

certificate from Electrical Inspector. The Capacity and Ratings of DG

sets are as below. (As per new CPCB4+ Emission norms Engine

With - Turbo Charger, EGR (Exhaust Gas Recirculation), CRS

(Common Rail Fuel System), DOC (Diesel Oxidation Catalyst), SCR

(Selective Catalytic Reduction), Integrated wiring harness

connected to ECU .)

Continuous rating of 200 KVA ,BHP not less than 254 BHP

17 Providing & erecting approved make AMF control panel suitable 1 Ea. 220509.00

for following size of 3 phase, 415 V., 50 cycles, A.C. diesel

generating set complete of scope as detailed below:

1) Power module: A pair of electromechanically interlocked

contactors (for mains & generator) Overload relay for generator

contactor Neutral contactor for mains and generator Power socket

for connections.

2) Control and metering module: Line voltage monitor. Generator

voltage monitor Ammeter 3 items attempt start facility. Air circuit

breakers/MCB/MCCB of suitable rating for auto/manual operation.

Auto/manual switch. Emergency stop push buttons. Manual start

push button. frequency meter. Engine hour meter. Two earthing

3) Protection module: The engine shutdown in the unlikely event of

Low lube oil pressure High cylinder head temperature. V belt

4) Indicators with alarm Load on generator.

5) Indicators Load on mains Engine fails to start . Emergency stop

battery charger.

The AMF Panel of following capacity

AMF Control Panel for200 KVA/250 KVA3 phase DG Set

18 Providing & erecting approved make ATS panel suitable for 1 Ea. 90679.00

following size of 3 phase, 415 V., 50 cycles, A.C. diesel generating

set complete of scope as detailed below:

1) Power module: Motorised Changeover switch with ATS

controller, Auxiliary contactor with NO & NC contacts with

Automatic Battery Charger, indicating lamps for Generator ON,

Mains ON, Load and suitable control terminals and power

terminals with neutral earthing studs.

ATS Panel for 180 / 250 KVA 3 phase DG Set

19 Supplying and erecting Acoustic enclosure (canopy) made out of 1 Ea. 262205.00

18 SWG, CRCA Sheet, sound absorbing material Rockwool of

density & 100 mm thick conforming to IS:8183 The resin bonded

Rockwool / PU FOAM covered from inside level not more than

dB at a distance of 1 mtr, as PVCT norms , on provided foundation

suitable for following size of DG Set. The enclosures for

following capacity of DG sets.

For for 160/180/200/250 KVA

D CABLES & TERMINATION

20 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 100 Ea. 891.00

multistrand Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following size

3 1/2 core 185 Sq. mm ( 95 Sq. mm 1/2 core)

21 Providing and erecting 18 G. M.S. termination box outdoor type 1 Ea. 899.00

suitable for- 1.1 KV PVC insulated armoured cable complete

erected with clamp, bolts, nuts etc. suitable of following size of

22 Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper 500 Mtr. 733.00

cable 1.1 KV grade to be erected as directed of following size.

23 Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper 100 Mtr. 236.00

cable 1.1 KV grade to be erected as directed of following size.

(K) 4 core 4 Sq. mm

24 (L) 4 core 6 Sq. mm 50 Mtr. 359.00

25 (M) 4 core 10 Sq. mm 300 Mtr. 565.00

26 (N) 4 core 16 Sq. mm 300 Mtr. 717.00

27 Providing & laying approved make Double walled corrugated 100 Mtr. 95.00

pipes (DWC) of polyethylene(conforming to IS 14930 II )with

necessary connecting accessories of same material at required

depth for laying of cable. below ground / road surface for

enclosing cable and back filling the same to make ground as per

28 Providing & laying approved make Double walled corrugated 100 Mtr. 136.00

pipes (DWC) of polyethylene(conforming to IS 14930 II )with

necessary connecting accessories of same material at required

depth for laying of cable. below ground / road surface for

enclosing cable and back filling the same to make ground as per

29 Making trench in soft soil of suitable width of 90 cms deep for 100 Mtr. 55.00

laying cable or locating the fault all over the run and backfilling the

same and making the surface as normal ground.

30 Providing and, fixing heavy duty flange type brass cable gland with 10 Ea 33.00

rubber ring for PVC insulated armoured cable complete with out

going tails, insulating tape etc for following size of cables.

(a) 2 to 4 core 2.5 Sq. mm

31 (b) 2 to 4 core 6 Sq. mm 4 Ea 38.00

32 (c) 2 to 4 core 10 Sq. mm 10 Ea 38.00

33 (d) 2 to 4 core 16 Sq. mm 10 Ea 47.00

34 Providing and, fixing heavy duty flange type brass cable gland with 8 Ea 236.00

rubber ring for PVC insulated armoured cable complete with out

going tails, insulating tape etc for following size of cables.

3 & 1/2 core 185 Sq. mm

35 Solder less crimping type Aluminium lugs conforming to IS suitable 24 Ea 80.00

for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

36 Solder less crimping type Aluminium lugs conforming to IS suitable 8 Ea 40.00

for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

37 Solder less crimping type Copper lugs conforming to IS suitable for 56 Ea 8.00

cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

40 Providing and Fixing Cable connection Junction Box for cable 7 Ea 10340.00

connection for Sub-mersible cable, made from CRC sheet with

input and output connector as requried of requried capacity havnig

size of approximate 600 x 600 x 150 duly painted with one coat of

red oxide and two coat of epoxy paint

D EARTHING WORK

41 Maintenance Free Chemical Earthing 10 Ea. 8551.00

Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250 Micron

galvanising, connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber

and heavy duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of installation duly

stamped and signed by agency and officer Incharge has to ensure

the value of earthing resistane mentioned in test Certificate) &

having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-

2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar

content:- <2%(C) Back fill Compound :- Earthing compound should

be capable to retain moisture for long time ecessary test report

must be submitted by Agency.

(c) For Electrical Installation covering Transformer Neutrals,

Lightning arrester Earthing, A.C.Plant & Sensitive Computer

System(like Automation, SCADA) i.e independent Earthing in

Length of Pipe : 3.00 mtrs

Back filling Compound :2 nos Bags of 25 Kg.

42 Providing and erecting required size HOT deep Galvanised iron 600 Kg 77.00

strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board,

Motors etc. using proper clamp.

43 Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 50 Kg 77.00

44 Providing one bag of 25 Kg. Additional Back Filling Compound (BFC) 10 Ea. 700.00

suitable for safe earthing device.

45 Mains with ISI marked, 1.5KV grade electrolyte multi stranded, 50 Mtr. 56.00

annealed copper conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing pipe of following

size with required size of copper lugs, nuts and bolts if required.

(e) One wire 6.00 sq. mm

(f) One wire 10.00 sq. mm 100 Mtr. 91.00

(g) One wire 16.00 sq. mm 20 Mtr. 141.00

46 Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 6 Pt 415.00

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multistrand copper wires, in following type of pipe to be

erected concealed in/ on surface on wall/ceiling complete with 6A

Modular type switch / bell push & accessories and earth continuity

of following type, erected on PVC / Metallic box, single mounting

base frame covered with textured/metallic front plate modules

erected on / in wall / ceiling as per pipe erected, with necessary

Lamp holder/ceiling rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories Cat- III

47 Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm 10 Pt 593.00

(Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated

multistrand copper wires, in following type of pipe to be erected

concealed in / flushed on wall/ceiling complete with 6A Modular

type switch and hum free EME four or more step type electronic

fan regulator with separately mounted and accessories with earth

continuity of following type erected on PVC / Metallic box, single

mounting base frame covered with textured/metallic front plate

modules erected on / in wall / ceiling as per pipe erected. with

necessary ceiling rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories Cat- III

48 Point wiring for Individual Plug with & earthwire of 1.5 sq.mm 2 Pt 441.00

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multistrand copper wires, in following type of to be erected

concealed in / on surface of wall / ceiling complete with Modular

type switch & 5 pin Plug erected on PVC / Metallic box covered

with appropriate front plate modules erected on / in wall / ceiling

as per pipe erected with following type of accessories.

[I] For 6A Plug with 2-1.5 sq.mm Cu. Wire

(a) with medium class Rigid PVC pipe and accessories Cat- III

49 Point wiring for Individual Plug with & earthwire of 1.5 sq.mm 4 Pt 782.00

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multistrand copper wires, in following type of to be erected

concealed in / on surface of wall / ceiling complete with Modular

type switch & 5 pin Plug erected on PVC / Metallic box covered

with appropriate front plate modules erected on / in wall / ceiling

as per pipe erected with following type of accessories.

[III] For 16A Plug with 2-4 sq.mm Cu. Wire

(a) with medium class Rigid PVC pipe and accessories Cat- III

50 Point wiring for on board Looped Plug with 6A Modular type 2 Pt 239.00

switch & 5 pin socket erected on PVC / Metallic box, single

mounting base frame covered with textured / metallic front plate

modules erected on / in wall / ceiling with following type

accessories Cat. III

51 Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm 1 Pt 525.00

& earthwire of 1.5 sq.mm (green) both are of .ISI marked 1.1 KV

grade FRLS PVC insulated multistrand copper wires, in following

type of pipe to be erected concealed in / flushed on wall/ceiling

,complete with 6A Modular type switches and following type of

accessories erected on PVC / Metallic box, single mounting base

frame covered with textured / metallic front plate modules erected

on / in wall / ceiling as per pipe erected. with necessary

batten/angle holder or ceiling rose or H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories Cat- III

52 Providing following type of Modular Type Accessories mounted 4 Ea 24.00

with pvc / metallic box, single mounting base frame covered with

textured / metallic front plate , modules erected with necessary

connection. As desired by Engineer In charge

(7) Blank Plate Single Cat III

53 Point wiring for secondary light point with 2-1.5 sq.mm & 12 Pt 131.00

earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multistrand copper wires, in following type of

pipe to be erected concealed in / flushed on wall/ceiling, complete

with earth continuity and necessary connection with primary light

with accessories erected on Metal / PVC box covered with 3 mm

thick PC(Polycarbonet) / Acrylic sheet for open / concealed wiring.

with necessary Lamp holder / ceiling rose / H.D.Connector as

Note:- Maximum up to 6 mtrs length, excess will be considered as

Mains for Secondary Point.

(a) with medium class Rigid PVC pipe and accessories

54 Providing and erecting ISI mark Medium class RIGID PVC PIPES of 100 Mtr 33.00

following size complete to be erected on/in wall or ceiling erected

with necessary PVC fittings & Junction boxes fixed with adhesive

solution & Clamps with following dia of pipes, in approved manner

57 Providing & erecting PVC Corrugated Flexible Conduit with 10 Mtr 21.00

required nos. of coupling, PVC bushes, Check-nuts etc. complete of

following sizes.

60 Supplying & erecting UPVC Mini trunking (PVC Casing-n-Capping) 20 Mtr 31.00

having double-locking arrangement with grooves, trunking of size

not below 12.5 mm in height as per IS with accessories of

PVC/Resin polypropylene not below 1.8 mm thick duly sealed in

joint & erected on wall / ceiling of following size .

61 Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded 10 Mtr 82.00

Copper conductor wire in following type of pipe to be erected

concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for

earth continuity of following size

(a) with medium class Rigid PVC pipe and accessories

(a) 3 wire 1.5 sq. mm

62 (b) 3 wire 2.5 sq. mm 200 Mtr 101.00

63 Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded 50 Mtr 139.00

Copper conductor wire in following type of pipe to be erected in /

on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of

(d) 3 wire 4 sq. mm

64 Supplying and erecting Flexible PVC insulated multistrand 25 Mtr 106.00

multicore 1.1 kv grade ISI marked copper wires of following size to

be erected as directed.

i) 2.50 Sq.mm 4 core round PVC sheathed

65 k) 4.0 Sq.mm 4 core round PVC sheathed 25 Mtr 175.00

LAMPS AND FITTINGS

66 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 16 Ea 370.00

Watt to 0.5 Watt assembled on single MCPCB, with housing used

as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name 160V

to 270V, Power Factor more than 0.95, THD < 15%,CCT 3000 K to

6500K, Luminaire efficacy> 85 lumens/watt ,LED LED driver

efficiency > 85 %( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select

any wattage capacity between the ranges shown.)

(A) Tube Light with integral driver

(iv) 22-24 Watts, Surge - 2KV,IP-20, conventional 4 feet

67 Providing and erecting decorative wall bracket fittings complete 2 Ea 1696.00

with LED lamp and rust free fittings components mounted in

chrome finish housing with holder ,clear/opaque glass diffuser

complete erected with lead wires with minimum 15 wattage

capacity as per instruction engineer incharge/architect/authority

SWITCHGEARS AND DISTRIBUTION BOARDS

68 Miniature circuit breaker single pole 6A to 32A suitable to operate 18 Ea 111.00

on 240 V A.C. system and having breaking capacity 10 KA to be

erected in existing box. confirming to IS 8828/1996 with ISI Mark

69 Providing & erecting 240 V MCB double pole switch for lighting 1 Ea 276.00

Load (B Curve) having 10 KA breaking capacity & confirms to IS :

8828 in existing box having following capacity

(A) 6 to 32 Amp. Cat. III

70 Providing & erecting 415V MCB Four Pole Switch for Lighting Load 1 Ea 573.00

(B curve) having 10KA breaking capacity & confirms to IS :8828 in

existing box having following capacity

(a) 6 to 32 Amp. Cat. III

71 (b)40 Amp. Cat. III 1 Ea 632.00

72 Providing & erecting 415 V MCB Four Pole for Motor & Inductive 1 Ea 730.00

Load (C Curve) having 10KA breaking capacity & confirms to IS

:8828 in existing box having following capacity

(c)63 Amp. Cat. III

73 Providing and erecting Sheet Steel powder coated MCB distribution 1 Ea 3379.00

board - flush / surface mounted fitted with busbar, neutral link,

earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should

be used of same company of MCB to be used) suitable for

(B) three phase incoming and single phase horizontal type outgoing

Per phase isolation type (PPI)

(b) sheet steel double door

74 Supplying & erecting Sheet Steel powder coated Cable end 1 Ea. 683.00

termination Box to be mounted on Top or Bottom of the MCB

Distribution Box for housing/covering Extra wires & Cables, suitable

for following size of MCB DB Box. (G) Three Phase 8 Way

75 The Above all items of MCB, DB the cost of erection on New angle 1 Ea 246.00

iron frame add following.

[B] above single phase 8 way and all three phase DBs.

76 Approved make ELCBs / RCCBs conforming to IS: 12640 and having 3 Ea 1950.00

sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA

and suitable for operation on single phase 240 V. having

characteristic of quick action & tripping with all advance feature &

do not incorporate any electronic component. for following Max.

rating erected as directed

(i) 25Amps. DP Cat III

77 (ii) 40Amps. DP Cat III 1 Ea 2213.00

78 Providing & erecting Medium Voltage Danger Notice Board sticker 2 Ea 26.00

of standard size

FANS & ACCESSORIES

79 Providing & erecting Approved make Power Saving 50 Watt Ceiling 10 Ea 1929.00

Fan with double ball bearing ISI mark with Condenser 230 volt A.C.

50 Hz 1200 mm sweep complete having 3blades with aluminium

blades with , canopy & 30 cms. down rod erected with 24/ 0.2,

core flexible wire with earthing.(Make shall be approved by

Engineer in charge))

80 Supplying and erecting 19 / 20 mm. nominal bore Medium Class 10 Ea 107.00

M.S. Pipe down rod erected duly painted for fan complete with

necessary 24/ O.20, 3 core flexible wire with earthing.

81 Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted 10 Ea 43.00

in RCC slab with Making the site as original.

82 Supplying & erecting fan hook box of 10 mm M.S. round bar 10 Ea. 107.00

bounded to the RCC bars up to 50mm length each side and pierced

through a 16 Gauge M.S. box / Heavy Duty PVC box complete

erected concealed in Ceiling with necessary finishing.

83 Providing Fan clamp of 30 x 5 mm flat of required length & 10 mm 10 Ea. 98.00

M.S. Bolt & Nuts erected with necessary hook of 10 mm M.S.

84 Providing 2.5mm.thick laminated acrylic sheet to cover the fan 10 Ea 18.00

hook or Fan box.

85 Supplying & erecting approved make low noise decorative exhaust 1 Ea 1687.00

fan having size 200mm with 1350 RPM with square frame ABS

body with inbuilt lowers & square frame.

86 Supplying & erecting single phase approved make industrial 6 Ea 3306.00

exhaust fan suitable for medium duty ring mounted low noise

operation suitable for medium duty having following dia size and

maximum speed in RPM

[D] 450 mm dia 900 RPM Cat.II

87 Providing suitable M.S. louver shutter of the Exhaust fan. 6 Ea 365.00

88 Supplying & erecting electro galvanised G.I. wire micro mesh jali 4 Sq.Mtr 628.00

cover of grade 304 required size with suitable wooden frame duly

fitted in wall outside of exhaust fan for insect protection.

89 Providing recess in wall or window frame suitable for erection of 6 Ea 188.00

Exhaust fan complete with plastering and colour washing to match

the colour of the wall or window complete with expanded metal in

order to render the fitting in accessible and the room water-proof.

90 Providing window frame suitable for erection of Exhaust fan 6 Ea 171.00

complete covering the remaining portion of window with 15 mm.

thick plywood and colour washing to match the colour of the wall.

91 Supplying and erecting approved make oscillating type bracket fan 1 Ea 2509.00

A.C. 23OV. 50cy/s 400/450 mm sweep wall mounted with height

adjustment and rotary tilting device complete with guard, flexible

Core plug top complete erected with lead wires as directed. Cat II

COMPREHENSIVE MAINTENANCE FOR 5 YRS

COMPREHENSIVE MAINTENANCE FOR 5 YRS AS

PER ATTACHED SHEET

TOTAL WITH O & M

Amount Put to Tender

PART – B COPREHENSIVE OPERATION AND MAINTENANCE

Sr. Total Daily Total Total Amt in

Desription KUB Power Day

No. Shift Rate Rate Rs.

Plant / Pump Operator

Semi Skilled person.

( 1 person x 3 Shift = 3 Person per

day) (June-November)

Plant / Pump Operator

Semi Skilled person.

( 1 person x 1 Shift = 1 Person per

day) (December-May)

Total Manpower cost for 01 Year of

A Total cost for 01 Year - A

B Insurance / P.F Approx @13% of - A

C E.S.I Approx @3.25% of - A

D Bonus @ 8.33% of -A

E Employee RC @ RC Rs.200/-

F Total Manpower cost for per Year

Contractor Profit approx @ 3.85% for 1st year(minimum service charges in the procurement of

Manpower As per GeM)

Total amount for 1st Year(A+B+C+D+E+F+G+H)

Total amount for 1st Year(A+B+C+D+E+F+G+H)

Pumping Station Name Total Amt in Rs.

I Capital Cost of pumping station

As Per Technical Sanction of 02 pumping station, machinery Cost

Grand capital cost of Two pumping station

Cost for Comprehansive work As per GWSSB @ 5 % of Capital cost - I

Contractor profit As per CPWD @ 15 % of - J

Section - B Total Cost for Comprehansive work (I+J)

Grand total of section-A and section-B(I+J)

Grand total of section-A and section-B(I+J)

Total Base amount for 2nd year

Price escalation in min wages & O&M cost approx @ 10% for 2nd year

Total amount for 2nd Year

Total amount for 2nd Year

Price escalation in min wages & O&M cost approx @ 10% for 3rd year

Total amount for 3rd Year

Total amount for 3rd Year

Price escalation in min wages & O&M cost approx @ 10% for 4th year

Total amount for 4th Year

Total amount for 4th Year

Price escalation in min wages & O&M cost approx @ 10% for 5th year

Total amount for 5th Year

Total amount for 5th Year

Total Amount of 5 Year

Total Amount of 5 Year

Total Amount of 5 Year Say

Total Amount of 5 Year Say

Amount In words :- Sixtyone lakh Eightythree Thousand One Hundred Only/-

1. The bid is percentage rate bid for Supply, Installation, Testing and

Commissioning of Pumping Machinery with allied Electro-Mechanical works with

Operation & Comprehensive Maintenance, and Defect Liability Period for 2 Years

2. The rates and prices shall be submitted in the formats given in the online

and the Bids will be disqualified.

3. It will be entirely at the discretion of the Employer to accept or reject the

bidder’s proposal, without giving any reasons whatsoever.

for items listed in the online schedule. Prices quoted in online Schedule only will

be considered for price evaluation & shall form a part of the Contract Agreement.

the successful bidder.

6. The bidder shall be deemed to have allowed in his price for provision,

maintenance and final removal of all temporary works of whatsoever nature

required for construction including temporary bunds, dewatering, diverting

water, pumping, providing civil foundation, required civil modification,

rectification, finishing work etc. to complete the Electro-Mechanical works. The

rates shall also be deemed to include any works and setting out that may be

required to be carried out for the same.

7. Where there is a discrepancy between the unit rates and the amount

Contract, the Specifications and other sections of these bid documents and

these documents are to be taken as mutually explanatory of one another.

9. Prices quoted by the bidder shall be firm for the entire period of Contract without

any escalation.

10. The bidder shall interpret the data furnished and carry out any additional study,

investigation or planning required to execute the work shall be at his own cost.

11. The prices quoted shall also include the cost of testing and materials utilized

12. The bidder should acquaint himself with the site conditions including the access

to Worksite. The successful bidder shall have to make suitable access to

worksites at his own cost. These accesses will be used by the other contractors

working for RMC.

13. The contractor shall have to avail P.F & E.S.I as per the applicable laws of

Government. The required documents shall have to be submitted by the contractor

to the competent authority.

14. The quoted rates should be inclusive of all taxes and duties.

15. The prices shall have to be quoted firm & fix including all the taxes & duties

without any statutory variation. RMC will not consider any statutory variation as

well as the price rise in the market and if any, those shall be on account of

16. The work contract tax will be borne by the agency.

17. Bidder shall note that RMC shall appoint PMC/TPI agency for supervision of this

work and fees pertaining to same shall be borne by RMC.

The Electro-Mechanical equipment and pipes shall be inspected by Third Party

Inspection Agency or RMC engineers, the costs of inspection procedure which

are to be borne by contractor. The Third Party Inspection Agency will be

from any Government undertaking agency like RITES, EIL, CEIL, MACON,

WAPCOS, SGS, etc. approved by RMC / Gujarat Water Supply & Sewerage Board

or such authorities.

Signature of Contractor ADDITIONAL CITY ENGINEER

Rajkot Municipal Corporation

Rajkot Municipal Corporation

Supply, Installation, Testing and Commissioning (SITC) of Pumping Machinery with

allied Electro-Mechanical works with 5 Years Operation & Comprehensive

Maintenance, and Defect Liability Period for 5 Years for Katariya Underbridge.

:: SCHEDULE - A ::

SUMMARY OF COST ESTIMATE FOR Katariya

UB (SITC / CAPITAL COST + O&M COST FOR

(BOQ & RATES FOR EACH AS PER SCHEDULE - B,)

Sr. Location of Estimated Cost of Project, in Rs.

Capital COMPREHENSIV Total

Cost E O&M Cost Amount

Katariya Underbridge,

at Kalawad Road ,Rajkot

GRAND TOTAL, RS.

GRAND TOTAL, RS.

I/We agree to carry out the above work at _ % (In Fig)

( (In words) Equal/Above/Below the

estimated cost.

Contractor shall have to quote their rates in the given online Price

Bid only. Please do not mention percentage quote in physical

AAE/AE Dy.Ex.Engineer Addi. CITY ENGINEER

Rajkot Muni. Corporation Rajkot Muni. Corporation Rajkot Muni. Corporation

Signature of Contractor:

Schedule of Payment % Break-up of payment for each component of the

Pumping Machinery during Supply, Installation, Trial Run & Commissioning.

Sr. No. Break-Up quoted

1. On supply of equipment at site 65%

2. On erection of equipment 15%

3. On testing and commissioning and successful trial run 20%

Any other items not specified above but considered necessary for completion of work to

the satisfaction of Engineer-in-charge and efficient operation of the plant / SPS.

After commissioning the pumping station O & M shall be the responsibility of the

Contractor to run Pumping station / pumping station for 5-years (60 months)

period and after that plant / pumping station should be handed over to the Client

Contractor’s Signature Addi. City Engineer

Rajkot Municipal Corporation