REPAIR TO FALSE CEILING AND OTHER MISC BR WORKS AT ZONE-III LANSDOWNE UNDER AGE I LANSDOWNE

Amount

S&F in repairs E-boards, ceiling, 4 mm thick with J framed work with main Tee of size 24 x 28.5 mm made out of PGI sheet .3 mm thick double at web and single at flange, flange coverd with powder coated sheet 0.25 mm thick and wall angle 24 x 24 x .45 mm powder coated for ceiling , ceiling boards 60cm x 60cm x 4mm thick , suspended with GI wire 2mm dia and 2m average length with adjustable hanging device complete including plugging in brick/stone walls with steel rawl plug @ 600 mm C/C Ceiling board shall be pressed to the ceiling tee with staple clips at all four sides and incl making good of all disturbed/daimage surface of walls and applying two coat of oil bound distemper complete all as spd & directed by GE/Eng-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding / terrazo dado etc (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for non skid coloured ceramic tiles of 9 to 10mm thick, (square/rectangular), area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floor and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed by Engineer-in-charge.

S & F glazed ceramic coloured tiles of size 450mmx300mmx 8 to 9mm thick on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick cement plaster in CM (1:4) all as specified and directed by Engineer-in-charge. Tiles shall be confirming to IS-15622-2017, Group B III with average water absorption between 10% to 15% length, width and strightness of sides +0.20% (Max deviation) Thickness + 4.0% (Max deviation) straightness of sides and rectangularity +0.15% (Max deviation) surface flatness +0.22% (max deviation). Breaking strength 500 N (Minimum) and minimum 95% tiles shall be free from visible defects. Note :- Shade of the tiles including colour, design and pattern shall be approved by AGE (I)

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed .

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. (Make : JSW, SAIL, TATA BLUE)

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed . (Make : JSW, SAIL, TATA BLUE)

S&F 0.63 mm thick galvanised zinc coated @ 120 gm / Sqm, corrugated mild steel sheeting in roof with two corrugations side lap fixed coach screws and washers , in roofs walls etc with grade of zinc coating 275 complete all as specifed and as directed.

S&F for 0.63 mm thick plain galvanised mild steel sheeting using grade ‘O’ sheets with 120 gm Zinc (Spelter) coating Per Sqm both sides inclusive, as in ridges, hips, valley gutters, drip and straight flashing fixed with ‘L’ or ‘J’ type hook and washers complete all as specified and directed.

Dismantling of timber scantling 40 sqcm and above in section in any position, unframed work complete all as specified and directed

Dismantling of timber scantling in fillets rafters, purlins etc under 40 sqcm in section complete all as specified and directed

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

M&L for second class hard wood as in scantling, fixed in unframed work clean sawn complete all as specified and directed

M&L for second class soft wood clean swan plain fillets, square, rectangular in section screwed with nails exc 13 & n exc 25 sqcm complete all as specified and directed

S&F for 20 mm thick 2nd class hard wood boarding planed one side with butt joints and fixed with nails as in roofs, ceiling partition fascia, barge soffit etc (except flooring and skirting) complete all as specified and directed

MAYA CONSTRUCTION

M/s Candid Mask Networks Pvt Ltd

EARMARK INFRATECH INDIA PVT. LTD.

Panwar Electrical

M/S STAR CONSTRUCTION