SPECIAL REPAIR REPLACEMENT OF LT PANELS AND OTHER CONNECTED MISC ITEMS AT VARIOUS E M INSTALLATIONS UNDER AGE I LANSDOWNE

Amount

Material and labour for design ,supply, fabrication, Installation, testing and commissoning Factory made LT panel at outdoor type totally enclosed, dust and vermin proof, suitably ventilated, floor mounted, 415 volts, 3 phase and neutral, 50 Hz AC supply system, fully compartmentalized, both side openable, made out of 3.00 mm thick CRCA sheet, protection of enclousure IP-54 as per IS: 2147 of 1962 with pre-treatment and powder coated of approved colour including suitable frame work/support made out of suitable size angle iron/flat iron, front opening type with provision for cable entry, with proper ferrule and cable glands, internal wiring with PVC insulated multi stranded copper conductor FRLS cable of adequate size(minimum 1.5 sqmm), including required civil works/anchoring bolts for fixing, PCC foundation etc with and including following all as specified and directed (at 3rd stage pump house). (Note - The job includes dismentling old unsv outdoor/indoor type switch gear panel alongwith associated busbar , meetring, fuses, MCCBs , u/s switches, starters etc indication lamp including disconnecting power cable all as specified and as directed. The complete dismantled items shall be handed over to MES deptt main store including transportation)

Material and labour for design ,supply, fabrication, Installation, testing and commissoning Factory made LT panel at outdoor type totally enclosed, dust and vermin proof, suitably ventilated, floor mounted, 415 volts, 3 phase and neutral, 50 Hz AC supply system, fully compartmentalized, both side openable, made out of 3.00 mm thick CRCA sheet, protection of enclousure IP-54 as per IS: 2147 of 1962 with pre-treatment and powder coated of approved colour including suitable frame work/support made out of suitable size angle iron/flat iron, front opening type with provision for cable entry, with proper ferrule and cable glands, internal wiring with PVC insulated multi stranded copper conductor FRLS cable of adequate size(minimum 1.5 sqmm), including required civil works/anchoring bolts for fixing, PCC foundation etc with and including following all as specified and directed (at Ration Strore Sub Stn):- (Note - The job includes dismentling old unsv outdoor/indoor type switch gear panel alongwith associated busbar , meetring, fuses, MCCBs , u/s switches, starters etc indication lamp including disconnecting power cable all as specified and as directed. The complete dismantled items shall be handed over to MES deptt main store including transportation)

Material and labour for design ,supply, fabrication, Installation, testing and commissoning Factory made LT panel at outdoor type totally enclosed, dust and vermin proof, suitably ventilated, floor mounted, 415 volts, 3 phase and neutral, 50 Hz AC supply system, fully compartmentalized, both side openable, made out of 3.00 mm thick CRCA sheet, protection of enclousure IP-54 as per IS: 2147 of 1962 with pre-treatment and powder coated of approved colour including suitable frame work/support made out of suitable size angle iron/flat iron, front opening type with provision for cable entry, with proper ferrule and cable glands, internal wiring with PVC insulated multi stranded copper conductor FRLS cable of adequate size(minimum 1.5 sqmm), including required civil works/anchoring bolts for fixing, PCC foundation etc with and including following all as specified and directed(at 2nd stage pump house):- (Note - The job includes dismentling old unsv outdoor/indoor type switch gear panel alongwith associated busbar , meetring, fuses, MCCBs , u/s switches, starters etc indication lamp including disconnecting power cable all as specified and as directed. The complete dismantled items shall be handed over to MES deptt main store including transportation and Location of IInd Stage pump house is not approachable by road, new LT Panel transport by manually is required which is approx 800 mtr ) :-

Material and labour for design ,supply, fabrication, Installation, testing and commissoning Factory made LT panel at outdoor type totally enclosed, dust and vermin proof, suitably ventilated, floor mounted, 415 volts, 3 phase and neutral, 50 Hz AC supply system, fully compartmentalized, both side openable, made out of 3.00 mm thick CRCA sheet, protection of enclousure IP-54 as per IS: 2147 of 1962 with pre-treatment and powder coated of approved colour including suitable frame work/support made out of suitable size angle iron/flat iron, front opening type with provision for cable entry, with proper ferrule and cable glands, internal wiring with PVC insulated multi stranded copper conductor FRLS cable of adequate size(minimum 1.5 sqmm), including required civil works/anchoring bolts for fixing, PCC foundation etc with and including following all as specified and directed (at Jharapani pump house):- (Note - The job includes dismentling old unsv outdoor/indoor type switch gear panel alongwith associated busbar , meetring, fuses, MCCBs , u/s switches, starters etc indication lamp including disconnecting power cable all as specified and as directed. The complete dismantled items shall be handed over to MES deptt main store including transportation)

Material and labour for design ,supply, fabrication, Installation, testing and commissoning Factory made LT panel at outdoor type totally enclosed, dust and vermin proof, suitably ventilated, floor mounted, 415 volts, 3 phase and neutral, 50 Hz AC supply system, fully compartmentalized, both side openable, made out of 3.00 mm thick CRCA sheet, protection of enclousure IP-54 as per IS: 2147 of 1962 with pre-treatment and powder coated of approved colour including suitable frame work/support made out of suitable size angle iron/flat iron, front opening type with provision for cable entry, with proper ferrule and cable glands, internal wiring with PVC insulated multi stranded copper conductor FRLS cable of adequate size(minimum 1.5 sqmm), including required civil works/anchoring bolts for fixing, PCC foundation etc with and including following all as specified and directed (at Lekhanagar Sub Stn):- (Note - The job includes dismentling old unsv outdoor/indoor type switch gear panel alongwith associated busbar , meetring, fuses, MCCBs , u/s switches, starters etc indication lamp including disconnecting power cable all as specified and as directed. The complete dismantled items shall be handed over to MES deptt main store including transportation)

Material and labour for design ,supply, fabrication, Installation, testing and commissoning Factory made LT panel at outdoor type totally enclosed, dust and vermin proof, suitably ventilated, floor mounted, 415 volts, 3 phase and neutral, 50 Hz AC supply system, fully compartmentalized, both side openable, made out of 3.00 mm thick CRCA sheet, protection of enclousure IP-54 as per IS: 2147 of 1962 with pre-treatment and powder coated of approved colour including suitable frame work/support made out of suitable size angle iron/flat iron, front opening type with provision for cable entry, with proper ferrule and cable glands, internal wiring with PVC insulated multi stranded copper conductor FRLS cable of adequate size(minimum 1.5 sqmm), including required civil works/anchoring bolts for fixing, PCC foundation etc with and including following all as specified and directed (KV Sub Stn):- (Note - The job includes dismentling old unsv outdoor/indoor type switch gear panel alongwith associated busbar , meetring, fuses, MCCBs , u/s switches, starters etc indication lamp including disconnecting power cable all as specified and as directed. The complete dismantled items shall be handed over to MES deptt main store including transportation)

Material and labour for design ,supply, fabrication, Installation, testing and commissoning Factory made LT panel at outdoor type totally enclosed, dust and vermin proof, suitably ventilated, floor mounted, 415 volts, 3 phase and neutral, 50 Hz AC supply system, fully compartmentalized, both side openable, made out of 3.00 mm thick CRCA sheet, protection of enclousure IP-54 as per IS: 2147 of 1962 with pre-treatment and powder coated of approved colour including suitable frame work/support made out of suitable size angle iron/flat iron, front opening type with provision for cable entry, with proper ferrule and cable glands, internal wiring with PVC insulated multi stranded copper conductor FRLS cable of adequate size(minimum 1.5 sqmm), including required civil works/anchoring bolts for fixing, PCC foundation etc with and including following all as specified and directed (at Zero Stage:- (Note - The job includes dismentling old unsv outdoor/indoor type switch gear panel alongwith associated busbar , meetring, fuses, MCCBs , u/s switches, starters etc indication lamp including disconnecting power cable all as specified and as directed. The complete dismantled items shall be handed over to MES deptt main store including transportation and Location of Zero Stage pump house is not approachable by road, new LT Panel transport by manually is required which is approx 700 mtr ) :-

Notes for Item No 1 to 7:- 1. Panel manufacturers should have in house powder coating plant with minimum 8 tansk pretreatment of MS sheet facilities, dust free spray paint booth.(8 tanks pretreatment process includes: degreasing/water rinsing/de-dusting/water rinsing/activation/phosphating water rinsing/passivation). 2. Thickness of powder coating shall not be less than 80 microns and test certificate for powder coating shall be furnished along with LT panel 3. The panel manufacturer should have following certification: (i) CPRI certification degree of protection IP-54 ( should have IEC:61439-1-2 & IEC:60529 tests) (ii) CPRI certification shrot circuit with stand strength should be 50 KA RMS for 1 sec with initial peak of 105 KA (iii) CPRI certification rated current for short circuit not less than 5000A 4. All the electricals switch gear like MCCBs, MCB should be of same make 5. Drawing of panel board should be got approved from GE before fabrication. 6. PAnel board should be fully compartmentalized in accordance to form 4 b of IEC 61439-1-2. 7. All Change over/MCCBs/MCBs should be mounted vertically in LT Panel

S&F in replacement of SPN 8 way MCB Distribution board double door, IP-43 prewired for mounting MCB/ isolator, ELCBs etc factory made, confirming to IS: 13032 fabricated out of CRCA sheet fitted with DIN channel, neutral link and bus bar 200 Amp complete all as specifeid and directed Make : ABB/BCH/L&T/Schneider/Siemens

S & F MCB SP 6 to 32 Amp, 240 Volts, having braking capacity 10 KA 'C' series all as specifeid and directed. Make : ABB/BCH/L&T/Schneider/Siemens

S & F MCB SPN 40 to 63 Amps, 240 Volts, having braking capacity 10 KA 'C' series all as specifeid and directed Make : ABB/BCH/L&T/Schneider/Siemens

S & F MCB TPN 40 to 63 Amps, 415 Volts, having braking capacity 10 KA 'C' series all as specifeid and directed Make : ABB/BCH/L&T/Schneider/Siemens

S&F in replacement of vertical TPN 4 way MCB Distribution board double door, IP-43 prewired for mounting MCB/ isolator, ELCBs etc factory made, confirming to IS: 13032 fabricated out of CRCA sheet fitted with DIN channel, neutral link and bus bar complete all as specifeid and directed Make : ABB/BCH/L&T/Schneider/Siemens

Supply and fix in replacement of LED flood light fitting 120W housing made out of pressure die-cast aluminium alloy with toughned glass, IP-66 protection, working on 240 Volts , 50 HZ, consisting of reflective lens wired with appropriate driver PF>0.98 having over voltage protection upto 440 volts, Surge protection level ≥ 10 KV, thermal short circuit protection THD < 10% made up of long life LED chips (SMD) in modular with Ra>70, and LED lumen efficiency >140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminior efficiancy > 110 Lumens/watt power LED should be of more than 01 watt CCT should be between 5700° K- 6500° K including fixed on pole of any type on existing angle iron with the help of nuts, bolts, washer including connecting with 1.5 sq mm, 3 core, PVC insulated Copper conductor cable 1100 Volts grade from pole box to light or from overhead conductor to light complete all as specified and as directed by Engr-in-Charge Make : Shakti Bajaj/ Havells/Wipro (i) the firm has to give warranty for Flood light fittings including driver minimum for 03 years for any defects developed during the period. (ii) The contractor shall submit the third party LM 79 report from any NABL approved laboratory. (iii) The fitting should have BIS, CRSno. Make Havells Cat Part No JETAIRSFLS120WLED /Shakti Cat Part No SZCFLPH120/Crompton Cat Part No LHBN 120-CDL ,

Disconnecting and dismantling old U/S pole box and S & F Loop in and Loop FRP rectangular SMC junction box x (Pole Box) made out of front operable hinged from side of size 240x130x110 mm suitable for outdoor installation weather proof having 4 pole cable connector (for cable in and out function) fixed inside box with insulator support and 01 nos MCB SP 06 Amp fixed inside box complete to pole for street light fitting with mS clamps 40x5 mm GI nuts, bolts and washers complete all as specified and directed. Make of Box:- Sintax/Hensel/EPP Make of MCB:- Havells/L&T/Schiender

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate. connected by 32X6 mm GI strip as earth lead by means of brass nuts and bolt,thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 40 mm dia light grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing wire to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighting not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

Supplying, laying, commisioning and testing of 1.1 KV grade XLPE insulated PVC sheathed steel armoured aluminum stranded conductor LT UG cable ( Conforming to IS 1554) ISI marked in trenches / ducts / through GI pipes under roads of size 240 sqmm 3.5 core complete all as specifed and directed. MAKE : Havells/Gloster/KEI/Grandley Note;- The earth work, GI pipe shall be measured and paid sepretely under appropriate item of Sch A.

Supplying, laying, commisioning and testing of 1.1 KV grade XLPE insulated PVC sheathed steel armoured aluminum stranded conductor LT UG cable ( Conforming to IS 1554) ISI marked in trenches / ducts / through GI pipes under roads of size 95 sqmm 3.5 core complete all as specifed and directed. MAKE : Havells/Gloster/KEI/Grandley Note;- The earth work, GI pipe shall be measured and paid sepretely under appropriate item of Sch A.

Supplying, laying, commisioning and testing of 1.1 KV grade XLPE insulated PVC sheathed steel armoured aluminum stranded conductor LT UG cable ( Conforming to IS 1554) ISI marked in trenches / ducts / through GI pipes under roads of size 50 sqmm 3.5 core complete all as specifed and directed. MAKE : Havells/Gloster/KEI/Grandley Note;- The earth work, GI pipe shall be measured and paid sepretely under appropriate item of Sch A

Supplying, laying, commisioning and testing of 1.1 KV grade XLPE insulated PVC sheathed steel armoured aluminum stranded conductor LT UG cable ( Conforming to IS 1554) ISI marked in trenches / ducts / through GI pipes under roads of size 25 sqmm 4 core complete all as specifed and directed. MAKE : Havells/Gloster/KEI/Grandley Note;- The earth work, GI pipe shall be measured and paid sepretely under appropriate item of Sch A

Supplying, laying, commisioning and testing of 1.1 KV grade XLPE insulated PVC sheathed steel armoured aluminum stranded conductor LT UG cable ( Conforming to IS 1554) ISI marked in trenches / ducts / through GI pipes under roads of size 10 sqmm 2 core complete all as specifed and directed. Make : Havells/Gloster/KEI/Grandley Note;- The earth work, GI pipe shall be measured and paid sepretely under appropriate item of Sch A

S&F Cable jointing kit for 11 KV (Earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of 95 Sqmm 3 core complete all as specified and directed.

S&F Cable jointing kit for 11 KV (Earthed) grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of 95 Sqmm 3 core complete all as specified and directed.

Excavation in trenches in hard/dense soil n.exc 1.5 m wide and n.exc 1.5 m in depth for poles,laying under ground electric cable and GI tubing (where provided for protection of cables), stay and getting out, trimming the sides, forming bottom surface to required level in any type of soil complete all specified and directed by Engg-in-Charge.

Returning , filling in, any type of soil including spreading, leveling, watering and well ramming in layers n.exc 250mm thick, in any tupe of soil complete all as specified and directed by Engg-in-Charge.

Removing excavated material (surplus soil) to a distance not exceeding 50m and depositing where directed at a level n.exc 1.5 m above the starting point, complete all as specified and directed by Engg-in-Charge.

M&L for sand cushioning for under ground cable with layer of fine river dry sand 80 mm thick before laying of cable and 150 mm thick after laying of cable in trenches complete all as specified and directed by Engg-in-Charge. Note:- Punned (consolidated ) thicness of sand will be measured and paid.

M&L for un-reinforced precast concrete cable cover class HVP, type 1 with peak size 250mmx150mm x 40mm compliance with IS:5820-1970, as cable protection over sand cushioning perpandicular across the cable length wise in trenches complete all as specified and directed by Engg-in-Charge.

M&L for 80 mm bore GI tube light grade laid under road/culvert/drain fixed to pole wall with help of flat iron clamps etcfor cable protection and making good surface of road with PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) complete all as specified & directed by Engg-in-Charge.

M&L for 50 mm bore GI tube light grade laid under road/culvert/drain fixed to pole wall with help of flat iron clamps etcfor cable protection and making good surface of road with PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) complete all as specified & directed by Engg-in-Charge.

KAPOOR ELECTRICALS