Loading
Loading…
Loading…
Tender Value
₹93.1 L
EMD Value
₹1.9 L
Closing Date
21 Oct 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
GENERAL
15 conditions · 4 needing a document upload
(As per advance correction slip No.1 of GCC April 2022) The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB of GCC-April-2022 along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Annexure V & VA :- As per Clause 6.1 Part-1 of GCC- The tenderer shall submit a copy of certificate (Enclosed as Annexure-V) stating that all their statements/documents submitted alongwith bid are true and factual. Non submission of above certificate by the bidder shall result in summarily rejection of his/their bid.
The minimum Eligibility Criteria: for costing more than 50 lakhs :- Applicable.10. Eligibility Criteria: 10.1 Technical Eligibility Criteria: (a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b)(1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the followingcategories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b (1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases,what constitutes a component in a composite work shallbe clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity.(b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through aworks contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway. In case after award of contract or during execution
Note for Item 10.1: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.10.1Definition of similar works :The criteria for similar nature of work for said tender is given below as CEE/JBP's L. No. WCR/L/10/Similar Nature/3689, dtd. 11.04.2012. similar nature of work criterion for Electrical General Service (GS) for Electrification work in Electrical department of WCR shall include works executed with Central Government, Semi Government/PSUs of Central Government and/or State Governments have been defined as under :- (A)The level of skills required in following work of electrification is almost same. (a) Electrification of service buildings.(b) Electrification of staff quarters, offices.(c) Electrification of offices.(d) Electrification of road & colony lighting.(e) Electrification of circulating area lighting.(f) Erection & commissioning of LT, HT upto 33 kV overhead mains.(g) Sub- stationinstallations & commissioning.(h) Electrification of washing pits, Sheds & Workshops etc.(i) Any above work or combination of (a) to (h) above.
33 conditions · 3 needing a document upload
Labour Cooperative Societies shall submit only 50% of bid security for which the tenderers are required to upload Registration certificate issued by appropriate authority without which their offer will not be considered. Such firms should also declare that -" We are a Labour Cooperative Society and our Registration No. is .................... with .......................and hence required to deposit only 50% of Bid Security
Any firm recognized by Department of Industrial Policy and Promotion (DIPP) as 'Startups' shall be exempted from payment of Bid Security on submission of Registration Certificate issued by appropriate authority. For such firms it is required to upload a copy of Registration Certificate issued by appropriate authority without which their offer will not be considered. Such firms should also declare that - I/We am/are a Startup firm registered by ........................ Department of Industrial Policy and Promotion (DIPP) and my registration number is ................ valid upto ...................... (Copy enclosed) and hence exempted from submission of Bid Security.
THE OFFERS WITHOUT EARNEST MONEY EXCEPT IN CASE OF EXEMPTION CLAIMED AS PER COMMERCIAL COMPLIANCE OF NIT WILL BE SUMMARILY REJECTED.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Performance Guarantee: - Additional 5% PG to besubmitted if tender awarded more than 5% below(Ref : para-4 of Rly. Bd. L.No.2022|CEUCTIGCC2022[ POLICY/Pt.I (E-3320424), Dated13.03.2026.
This tender complies with Public Procurement Policy (Make in India) Order 2017, dated 15/06/2017, issued by Department of Industrial Promotion and Policy, Ministry of Commerce, circulated vide Railway Board letter no.2015/RS(G)/779/5 dated 03/08/2017 and 27/12/2017 and amendments/ revisions thereof.
Implementation of Labour Codes: - Contractor/Tenderer has to ensure Implementation of Labour Codes and strengthening compliance in respect of labour - reg. (Ref. - Rly. Bd. L. No. 2026/E(LL)/AT/CNR/5, dtd. 05.08.2026 and WCR/JBP's L. No. WCR/L/01/1134/Rly.Bd, dtd. 18.08.2026 (Attached a document).
Miscellaneous work for reliability improvement of electrical substation ,provision of pathway in yard area for shunting staff movement at WRS Kota & WRS Kota Extension of stripping shop (size-40mX48 m).
EL-50-332-2026-27~WCR
EL-50-332-2026-27
Open
Works - General
10 Months
Kota, Rajasthan
₹0
₹1.9 L
28 Sept 2026
28 Sept 2026
7 Oct 2026
86 items across 2 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 46,44,037.7 | ||
| — | 30.00 | — | — | ||
| To remove the old cables from existing panels & dressing & cutting or lugging of existing cables and re-connection to the existing panel as per site requirement. Location-in existing cable trench at SS-2 and other locations. | — | — | — | 29,700 | |
| — | 27.00 | — | — | ||
| Providing and fixing of precoated galvanized iron profile sheet/chequered plate (size125cmX65cmX0.6cm) over cable trench | — | — | — | 1,32,300 | |
| — | 50.00 | — | — | ||
| To fill up the existing trench with sand. (Volume of sand) | — | — | — | 1,04,500 | |
| — | 200.00 | — | — | ||
| Supply & provision of MS clamps for LT cable & clamping the existing cable of various size.It includes - suitable fastener Clamp, and Nut bolt etc as per site requirement. | — | — | — | 58,000 | |
| — | 200.00 | — | — | ||
| Ballast work in switch yard at receiving substation & other H pole & substation. It includes (1) Removal of existing ballast from switch yard.(2) Cleaning of the yard properly to remove all bushes and other unwanted materials from yard.(3) Screening of existing ballast & refilling of ballast in yard. | — | — | — | 1,96,000 | |
| — | 55.00 | — | — | ||
| Supply and Erection of reinforced concrete for cable trench cover etc as per explanatory notes. | — | — | — | 1,22,925 | |
| — | 60.00 | — | — | ||
| Supply & installation of Earthing pit as per explanatory notes. It includes supply & provision of earthing pit made of cement structure. As per sample provided by railway.It also includes checking connection of earth wire, to check value of earth resistance & replacement of earthing wire nut bolt if required. | — | — | — | 59,100 | |
| — | 100.00 | — | — | ||
| Supply and erection of fencing panel & gates at substation as per explanatory notes.It includes supply of MS fencing and erection near H pole of HT Supply & LT panel in the shop. | — | — | — | 3,64,600 | |
| — | 1.50 | — | — | ||
| Supply and erection of fencing up right as per explanatory notes. It includes supply of MS fencing and erection near H pole of HT Supply & LT panel in the shop. | — | — | — | 1,18,165.5 | |
| — | 9.00 | — | — | ||
| Dismantling of old VCB & HT change over at Receiving Substation and submitted at WRS store with transportation. | — | — | — | 44,100 | |
| — | 10.00 | — | — | ||
| Disconnection of all cables, Dismantling of Old LT Panel off sort size and storing it in electrical store as per explanatory notes. | — | — | — | 39,500 | |
| — | 3.00 | — | — | ||
| Supply, fabrication, installation, testing & commissioning of LT distribution board fabricated with MS angle Size 40X40X5 mm with door and locking arrangement duly painted red oxide and power coated enamel paint consisting of following items - IN COMING - MCCB TPN 250 Amp. Breaking capacity 35 KA - 01 NO. , Ampere meter with selector switch 0-300 Amp.-01 no., voltmeter with selector switch 0-500 volt -01 NO., indication lamp RYB 03 nos., fuse for indication 05 nos., CT 300/5- 03 nos., busbar 400 Amp. rating- 01 set. & bus bar insulator-1 set, Changeover 4P 400 Amp. - 01. OUT GOING - MCCB 200 Amp. 4P breaking capacity 25 KA- 02 nos. and MCCB 100 Amp. 4P breaking capacity 25 KA- 02 nos. Complete in all respect. | — | — | — | 2,75,577 | |
| — | 3000.00 | — | — | ||
| Laying, testing and commissioning of LT XLPE insulatedstranded armour conductor cables of various size. The cables to be laid in existing trench/air/ pipe and connection with crimped lugs & cleating of the cable. Note - Cable will be supplied by Railway. | — | — | — | 88,200 | |
| — | 2200.00 | — | — | ||
| Digging of trench in all type of soils/road cutting 100 cm. deep and 50cm. wide including supply and laying of "B" class bricks on both side & top of the cable and refilling the trench after laying of cable. | — | — | — | 3,66,806 | |
| — | 400.00 | — | — | ||
| Digging of trench in pucca trench in yard/ platform 50 cm. deep and 35 cm. wide including re-plaster on surface by cement concrete after laying of cable. Wherever the digging of trench to full size is not possible, measurement will be proportionate to the actual volume of cross section and length of the trench. | — | — | — | 1,06,308 | |
| — | 10.00 | — | — | ||
| Supply and erection of concrete for foundation and plinth in other than hard soil 15 & rock as per explanatory notes. Supply and Erection of 16 reinforced concrete for cable trench cover etc as per explanatory note. | — | — | — | 16,710 | |
| — | 10.00 | — | — | ||
| Fabrication of suitable size covered shed by supply of material. It includes supply of MS 40mmX40 mm Iron pipe with colour sheet with 0.5MM thick sheet, Hot finished seamless type tube MS Pipe & rcc foundation work. fabrication of covered shed at site as per requirement of panel Small size (3feetX3 feet) , height of shed 8 feet as per explanatory notes. | — | — | — | 41,000 | |
| — | 5.00 | — | — | ||
| Fabrication of suitable size covered shed by supply of material. It includes supply of MS 40mmX40 mm Iron pipe with colour sheet with 0.5MM thick sheet, Hot finished seamless type tube MS Pipe & RCC foundation work. Fabrication of covered shed at site as per requirement of panel Small size (6feetX6 feet) , height of shed 8 feet as per explanatory notes. | — | — | — | 54,500 | |
| — | 100.00 | — | — | ||
| Supply and spreading of gravels/ ballast as per explanatory notes. | — | — | — | 1,66,200 | |
| — | 110.00 | — | — | ||
| Supply and Installation, fixing of Octagonal pole/pole of 3 meter(approx.) height Double Arm Type capable of fixing of LED light fitting and should have inbuilt junction box. The material should be of relevant IS and design as per site conditions (Note:- Designs should be approved by railways before supply by competent authority.). The Pole should be complete in all respect as per explanatory notes. | — | — | — | 10,91,200 | |
| — | 220.00 | — | — | ||
| Supply, installation & testing of outdoor type, street light, LED light fitting 18 Watts and making connection with existing light point. Fixing should be performed as per site requirement | — | — | — | 4,78,060 | |
| — | 25.00 | — | — | ||
| Supply of material & providing GI. Pipe earthing arrangement by digging the pit as per DRM/KTT's Drg. No. 01913EL/R1 or latest complete in all type of soils including rocky area. Earth value will be taken by the contractor in the presence of Railway representative and written on the earth pit by the contractor. | — | — | — | 53,500 | |
| — | 4.00 | — | — | ||
| — | 100.00 | — | — | ||
| — | 120.00 | — | — | ||
| — | — | — | 50,551.2 | ||
| — | 4.00 | — | — | ||
| Supply of material & Erection of Maintenance Free Earth Electrodes station as per RDSO Specification No.RDSO/Spn./197/2008 or latest complete in all type of soils including rocky area. Earth value will be taken by the contractor in the presence of Railway representative and written on the earth pit by the contractor. | — | — | — | 61,924 | |
| — | — | — | 46,66,573.2 | ||
| — | 3600.00 | — | — | ||
| Supplying, Laying testing and commissioning of PVC insulated, single core 16 sqmm aluminium conductor unarmoured cable for 30%, 70% & 100% with earth wire of 8 SWG. This arrangement must be laid as per site requirement with necessary accessories such as clamps, reel insulator, nut, bolt etc.It should be complete in all respect | — | — | — | 2,12,400 | |
| — | 1600.00 | — | — | ||
| Supplying, laying testing and commissioning of single core aluminium conductor unarmoured cable of size 240 sqmm per phase along the shop. It should be for R, Y, B & N plus GI earth wire (8 SWG) complete with reel insulators, shackle point with suitable clamp, nut, bolts arrangement with termination as per explanatory notes. | — | — | — | 7,44,000 | |
| — | 1600.00 | — | — | ||
| Supplying, laying testing and commissioning of single core aluminium conductor unarmoured cable of size 35 sqmm per phase along the pillars. It should be for R, Y, B & N plus GI earth wire (8 SWG) complete suitable clamp, nut, bolts arrangement with termination as per explanatory note | — | — | — | 1,41,600 | |
| — | 84.00 | — | — | ||
| Supply, installation & testing of LED flood light fitting 50 Watts and making connection with existing light point. Fixing should be performed as per site requirement. | — | — | — | 2,37,552 | |
| — | 84.00 | — | — | ||
| Supply installation of Air Circulator Fan 600 mm & making connection with existing fan point. Fixing should be performed as per site requirement. | — | — | — | 6,57,804 | |
| — | 80.00 | — | — | ||
| Supply, installation, testing & commissioning of LED high bay fitting,150 Watts and making connection with existing light point. Fixing should be performed as per site requirement. | — | — | — | 5,77,440 | |
| — | 2.00 | — | — | ||
| Supply, installation testing and commissioning of distribution panel suitable for outdoor use with canopy and double door type with stand as under, INCOMING CIRCUIT-01 No. MCCB 4 pole 400 Amp. 50 K A MP based LSIG Adj. O/L Adj. S/C. Ampere meter with selector switch -01 no., voltmeter with selector switch -01 no., indication lamp RYB 03 nos., Change over 01 no., Energy meter - 01 no., CT 400/5- 03 nos., Copper busbar 400 Amp. rating- 01 set, MCB 6A SP C 10KA - 04 nos.. OUTPUT CIRCUIT- 04 no. MCCB 3pole 200 Amp. 36 KA TMD, 02 no. MCCB 3pole 100 Amp. 36 KA TMD. All MCCB in outgoing circuit will provided with HRC Fuse etc. as per attached detailed specification. | — | — | — | 6,29,169.2 | |
| — | 500.00 | — | — | ||
| Laying, testing and commissioning of 400/120/150/240 Sqmm Aluminium 4 core XLPE, L.T.cable. The cable to be laid in existing trench/air/pipe as per explanatory notes. | — | — | — | 14,700 | |
| — | 100.00 | — | — | ||
| Digging of trench in all type of soils/road cutting 100 cm. deep and 50cm. wide including supply and laying of "B" class bricks on both side & top of the cable and refilling the trench after laying of cable. | — | — | — | 16,673 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC_April-2022_Final.pdf
ATTACHMENT
AnnexureLC-Inclusionofletterofcredit.pdf
ATTACHMENT
Annexure-E.pdf
ATTACHMENT
DempoymentofEngineers.pdf
ATTACHMENT
SpecificationofLEDLuminare-2026-1.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipNo11_11zon.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipNo.121.pdf
ATTACHMENT
NewMakeinIndiapolicylatestamendment.pdf
ATTACHMENT
tenderdocuments1_2.pdf
ATTACHMENT
GCCAdv.CorrectionslipofGCC1-10_compressed.pdf
ATTACHMENT
ImplementationofLabourCodesinrespectofcontractlabour_compressed.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .