Construction of Govt. Degree college building at Ronhat, in Tehsil Shillai, District Sirmour ( HP )

Amount

Excavation in earthwork in hilly area in all heights and depths, in all kind of soils by manual / mechanical means including saturated soil comprising of ordinary soil, soft rock, hard rock chiselling, wedging out of rock ( where blasting is prohibited) and their intermediate classification of soil setting out true to the required lines, grades, width camber and super elevation levels cutting and trimming of side slopes and level as show in the drawing and as directed by Engineer-in-Charge at site according to the MORD Technical Specification Clause 302,1603 and 1603.2 and sorting out useful materials and stacking, the same in all leads and lifts in acquired width of road and transportation of un useful material for filling in road ways, camber, embankments for grade improvements and disposal of all material to required width of the road or on approved dumping site through all modes of transportation including head load or animal transport or mechanical means along with its leveling fine dressing and carriage of machineries, materials , tools, equipments and safety measures incidentals necessary to complete the work by mechanical means and labour, if required all useful materials such as stone, shingle aggregate and slates etcetera. Shall be sort out stacked and measured. Recovery at the rate of Rs. 300/- only (Rupees three hundred) per cubic meter shall be effected from the bill, for the quantity actually measured or 242.61 (Two hundred forty two point six one) cubic meter on pro rata basis whichever is more. Any loss to the private property during the course of execution shall be the absolute responsibility of the contractor which shall have to be compensated by him in all cases.

Earth work in excavation for structure in all depths as per drawing & technical specification for Rural Road August 2004 clause 305.1 including setting out, construction of shoring & bracing, removal of stumps & other deleteruious materials & disposal in all leads & lifts including dressing of sides & bottom & back filling in trenches with excavated suitable materials. All work of rock cutting by blasting shall be carried out by taking all necessary precautions against soil erosion damage to hill side water pollution etc. and to protect stability of hill side rock shall be excavated with chiselling and wedging out rock ( where blasting is prohibited ). All earth work in cutting/excavation including rock excavation shall be carried out true to lines, grades, side slopes, width, camber super elevation and level as shown on the drawing or as directed by the Engineer-in-Charge hauling & stacking of materials useful for construction at suitable sites & safe disposal of unsuitable cut materials in specified manner tramming filling of unevenness blindage & finishing of the road to specified dimension or as directed by the Engineer-in-Charge. If the foundation of the structure is in an area with stagnant water or water is met with in the excavation due to sping seepage rain and other causes, it shall be remove by suitable diversion bailing out or pumping as directed and the area of the foundation or embankment shall be kept dry. Any loss to the public or private property during the course of excavation shall be the whole responisibility of the contractor which shall have to be duly compensated by him at his own cost in all cases.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains in all heights and depths in all kinds of soil, including saturated soil comprising of pick work,jumper work and blasting work both in soft and hard rock with chiesling and wedging out of rock (where blasting is prohabited) and their intermediate classification of soil including dewatering whereever required,settling out to required lines,levels as shown on the drawing and directed by the Engineer in charge at site according to the HP.PWD specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (to be arranged by the contractor) including payment of prescribed dumping charges of M.C. if levilled any to the satisfaction of the Engineer in charge through all modes of transporation including head load animal load or mechanical means alongwith its levelling, fine dressing and with all kinds of labour, mechineries, tools, equipment and safety measures and incidental necessary to complete the work by mechanical means and labour (if required). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transporation and used/removed as per the satisfaction of the Engineer in charge. any loss to the public and private properity during the course of execution and disposal of servicable and unservicable materials shall be the absolute responsiblity of the contractor and shall have to be duly compensated by him in all respects including all incidential charges and as directed by the Engineer in Charge:- All kinds of soil.

Construction of embankment with approved materials deposited at site from road way cutting & excavation from drain & foundation of other structures graded and compacted to meet the requirement of Table 300.1 & 300.2 as per Technical Specification clause 301.5 including hauling of materials within all leads & lifts & other incidential charges & as per direction of Engineer-in-Charge.

Supplying & filling in plinth with sand under floors including watering, ramming, consolidating & dressing complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & laying cement concrete Mechanically mixed & Vibrated 1 : 6 : 12 ( One cement : six coarse sand : twelve graded crushed stone aggregate 40 mm ( forty milimetre ) nominal size ) for plain/ reinforced concrete work in open foundation complete as per drawing & technical specification clauses 802, 803, 1202 & 1203 including cost of form work & curing complete including all leads, lifts & carriage of materials, as per the entire satisfaction of the Engineer-in-Charge.

Providing and laying in position cement concrete of specified grade mechanically mixed and curing complete excluding the cost of centering and shuttering - All work up to plinth level and all floor level in 1:5:10 (One Cement : five coarse sand : ten graded stone aggregate 40mm (forty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying in position cement concrete of specified grade mechanically mixed and curing complete excluding the cost of centering and shuttering - All work up to plinth level and all floor level in 1:4:8 (one Cement : four coarse sand : eight graded stone aggregate 40mm (forty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & laying cement concrete Mechanically mixed & Vibrated 1 : 4 : 8 ( One cement : four sand : eight graded crushed stone aggregate 20 mm ( twenty milimetre ) nominal size ) for plain/ reinforced concrete work in open foundation complete as per drawing & technical specification clauses 802, 803, 1202 & 1203 including cost of form work & curing complete including all leads, lifts & carriage of materials, as per the entire satisfaction of the Engineer-in-Charge.

Providing & laying cement concrete Mechanically mixed & Vibrated 1 : 3 : 6 ( One cement : three sand : six graded crushed stone aggregate 20 mm ( twenty milimetre ) nominal size ) for plain/ reinforced concrete work in open foundation complete as per drawing & technical specification clauses 802, 803, 1202 & 1203 including cost of form work & curing complete including all leads, lifts & carriage of materials, as per the entire satisfaction of the Engineer-in-Charge.

Making plinth protection 50 mm ( fifty milimetre ) thick of cement concrete 1 : 3 : 6 ( One cement : three coarse sand : six graded stone aggregate 20 mm ( twenty milimetre ) nominal size ) over 75 mm ( seventy five milimetre ) thick bed of dry brick ballast 40 mm ( forty milimetre ) nominal size, well rammed & consolidated & grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying in position cement concrete of specified grade mechanically mixed , vibrated & curing complete excluding the cost of centering, shuttering, finishing & reinforcement - All work up to plinth level and all floor level in 1:1.5 : 3 (One Cement : One & half coarse sand : five graded stone aggregate 20mm (twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying reinforced cement concrete work in walls (any thickness), mechanically mixed, vibrated and curing complete including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor all level , excluding cost of centering, shuttering, finishing and reinforcement in 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20mm ( twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying reinforced cement concrete work mechanically mixed & vibrated in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor all level mechanically mixed, vibrated and curing complete, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20mm ( twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying reinforced cement concrete work mechnanicall mixed in vertical and horizontial fins individually or forming box louvers, facias & eaves boards above plinth level upto floor five level, excluding the cost of centring,shuttering, finishing and reinforcement with 1 : 1.5 : 3 ( One cement : one & half coarse sand : three graded stone aggregate 20 mm nominal size ), including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing form work with steel plates 3.15mm ( three point fifteen millimeter ) thick welded with angle iron in frame 30X 30X5mm ( thirty X thirty X five millimeter ) so as to give a fair finish including centering ,shuttering, strutting and propping etc. with wooden battens and ballies , height of propping and centering below supporting floor to ceiling not exceeding 4.00 meters ( four meters ) and removal of the same for insitu- reinfoced concrete and plain concrete work including all leads and lifts of materials or as per the directions of Engineer in Charge.

Foundations, footings, bases of columns, etc. for mass concrete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Walls ( any thickness ) including attached pilasters, buttresses, plinth & string courses etc. including all leads, lifts & carraiage of materials & to the entire satisfaction of the Engineer-in-Charge .

Suspended floors, roofs, landings, balconies and access platform including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Lintels, beams, plinth beams, girders, bressumers and cantilevers including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Columns, Pillars, Piers, Abutments, Posts and Struts Circular including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Stairs, (excluding landings) except spiral stair cases including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Vertical & Horizontial fins individually or forming box louvers band, facias & eaves boards ,including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Edges of slabs and breaks in floors and walls Under 20cm ( twenty centimeter ) wide including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and placing steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding wire all complete upto floor all level. Thermo-Mechanically Treated bars of grade Fe-500 D or more including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Rat trap bond brick work with common burnt clay F.P.S. ( Non-modular ) bricks of class designation 7.5 in foundation & plinth in cement mortar 1 : 6 ( One cement : Six coarse sand ) including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Rat trap bond brick work with common burnt clay F.P.S. ( Non-modular ) bricks of class designation 7.5 in Super-structure above plinth level upto all floor level in cement mortar 1 : 6 ( One cement : six coarse sand ), including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation & plinth in all shapes and sizes in Cement mortar 1 : 6 ( One cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in Cement mortar 1 : 6 (one cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1 :4 ( One cement : four coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level in all shapes and sizes : Cement mortar 1 : 4 ( One cement : four coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Coursed rubble masonry ( second sort ) with hard stone in foundation & plinth in cement mortar 1 : 6 ( One cement : six coarse sand ), including all leads, lifts & carriage of materials & to the entire satisfaction of Engineer-in-Charge

Coursed rubble masonry ( second sort ) with hard stone in super structure above plinth level & upto all floor level in cement mortar 1 : 6 ( One cement : six coarse sand ), including all leads, lifts & carriage of materials & to the entire satisfaction of Engineer-in-Charge

Stone/ boulder filling behind retaining wall/ under flooring, including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing 18 mm ( eighteen milimetre ) thick gang saw cut, mirror polished, premoulded & prepolished, machine cut for kitchen plateforms,vanity counters, window sills, facias & similar locations of required size, approved shade, colour & texture laid over 20 mm ( twenty milimetre ) thick base cement mortar 1 : 4 ( One cement : four coarse sand ), joints treated withwhite cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, coulding & polishing to edges to give high glass finish etc. complete at all level Baroda green marble of any colour, shade & all area of slab including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing 20 mm ( twenty milimetre ) thick Jet black Granite stone gang saw cut, mirror polished, premoulded & prepolished, machine cut for work top of Laboratory & similar locations of required size, approved shade, colour & texture laid over 20 mm ( twenty milimetre ) thick base cement mortar 1 : 4 ( One cement : four coarse sand ), joints treated withwhite cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, coulding & polishing to edges to give high glass finish etc. complete at all level Jet black Granite stone & all area of slab including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing Ist quality Ceramic glazed wall tiles conforming to IS: 15622 ( thickness to be specified by the manufacture ),of approved make in all colours, shade of any size as approved by Engineer-in-Charge, in skirting, risers of steps & dados, over 12 mm ( twelve milimetre ) thick bed of cement mortar 1 : 3 ( One cement : three coarse sand ) & jointed with grey cement slurry @ 3.3 Kg ( Three point three Kilograme ) per Square meters, including pointing in white cement mixed with pigment of matching shade complete, including all leads,lifts & carriage of materials & to the entire satisfaction of Engineer-in-Charge

Providing & fixing dry cladding upto all heights from floor level with 30 mm ( thirty milimetre ) thick gang saw cut stone with ( machine cut edges ) of uniform colour & size upto 1.0 metre into 1.0 metre ( one metre into one metre ) , fixed to structural steel frame work and / or with the help of cramps, pins etc. and sealing the joints with approved weathers sealant as per Archtectural drawing & direction of the Engineer-in-Charge ( The steel frame work, stainless steel cramps & pins etc. shall be paid for separately ) Red sand stone 30 mm ( thirty milimetre ) thick gang saw cut stone, including all leads,lifts & carriage of materials & to the entire satisfaction of Engineer-in-Charge

Providing & fixing panelling or panelling & glazing in panelled or panelled & glazed shutters for doors, windows & clerestory windows ( Area of opening for panel inserts excluding portion inside grooves or rebates to be measured ), panelling for panelled or panelled & glazed shutters 25 mm to 40 mm ( twenty five milimetre to forty milimetre ) thick Particle board 12 mm ( Twelve milimetre ) thick pre-laminated particle board with decorative lamination on both side, grade 1, Type-II, IS: 12823 marked, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing panelling or panelling & glazing in panelled or panelled & glazed shutters for doors, windows & clerestory windows ( Area of opening for panel inserts excluding portion inside grooves or rebates to be measured ), panelling for panelled or panelled & glazed shutters 25 mm to 40 mm ( twenty five milimetre to forty milimetre ) thick Float glass panes 6.00 mm thick glass panes ( weight not less than 12.50 Kg ( Twelve point five kilograme ) per square metre, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing wooden moulded beading to door & windows frames with iron screws, plugs & priming coat on unexposed surface etc. complete second class teak wood 50 x 12 mm ( fifty into twelve milimetre ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium sliding door bolts, ISI marked anodised ( Anodic coating not less than grade AC 10 as per IS:1868 ), transparent or dyed colour to required colour or shade, with nuts & screws etc. complete 300 x 16 mm ( three hundred into sixteen milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium sliding door bolts, ISI marked anodised ( Anodic coating not less than grade AC 10 as per IS:1868 ), transparent or dyed colour to required colour or shade, with nuts & screws etc. complete 250 x 16 mm ( two hundred fifty into sixteen milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 200 x 10 mm ( two hundred into ten milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 100 x 10 mm ( One hundred into ten milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium handles ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 125 mm ( one hundred twentyfive milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium handles ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 75 mm ( Seventy five milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

(36.01) Providing & fixing aluminium hanging floor stopper ISI marked anodic coating not less than grade AC 10 as per IS: 1868 ) transparent or dyed to required colour & shade, with necessary screws etc. complete Single rubber stopper including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. i) 50mm (Fifty milimeter) height.

(36.02)Providing & fixing aluminium hanging floor stopper ISI marked anodic coating not less than grade AC 10 as per IS: 1868 ) transparent or dyed to required colour & shade, with necessary screws etc. complete Twin rubber stopper including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.ii) 100mm (One hundred milimeter) height.

Providing & fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand ) logo with ISI, IS:3564, embossed on the body, door weight upto 35Kg ( Thirty five kilogram ) door with upto 700mm ( seven hundred milimetre ) with necessary accessories & screws etc. complete, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing Cub board shutters 19 mm ( nineteen milimetre ) thick with pre-laminated flat pressed three layers particle board or graded wood particle board IS: 12823 marked exterior grade ( Grade I type II ) , having one side decorative lamination & other side balancing lamination, including second class teak wood lipping of 25 mm wide 12 mm thick ( twenty five milimetre wide twelve milimetre ) thick ) with necessary screws & bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing 19 mm ( Nineteen milimetre ) thick water proof commercial board in shelves/box for Cub board with butt joints & fixing with nails & screws etc. complete, including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing decorative high pressure laminated sheet of plain/ wood grain in gloss /matt/ Suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS: 2046 Type-S, including cost of adhesive of approved quality 1.00 mm ( One milimetre ) thick sheet, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing ply wood 4 mm ( four milimetre ) thick, one side decorative veneer conforming to IS: 1328 (Type-1 ), for plain lining/ cladding with necessary screws, including priming coat on unexposed surface with decorative veneer facing of approved manufacture including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing special quality bright finished brass cub board or ward robe locks with four levers of approved quality including necessary screws etc. complete 50 mm ( fifty milimetre ) size, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing 50mm ( fifty milimetre ) bright finished brass cub board or ward robe knob of approved quality with necessary screws, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing magetic catcher of approved quality in Cub board/ ward robe shutters, including fixing with necessary screws etc. complete double trip ( horizontal type ), including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing expandable fasterners of specified size with necessary plastic sleeves & galvanised mild steel screws including drilling holes in masonry work/ cement concrete/ reinforced cement concrete & making good etc. complete 40 mm long, including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Structural steel work riveted, bolted or welded in built up sections, trusses & framed work,including cutting, hoisting, fixing in position & applying a priming coat of approved steel primer all complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing mild steel round holding down bolts with nuts & washers plates complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position & applying a priming coat of approved steel primer using structural steel etc. as required in grating, frames, guard bars, ladders, railing, brackets, gates & similar work including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing structural steel frame ( for dry cladding with 30 mm ( thirty milimetre ) thick gang saw cut with manhine cut edges sand stone on walls at all heights from floor level using M.S. square/ rectangular tube in the required patteren as per Architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the frame & embedded in brick wall with cement concrete block 1 : 2 : 4 ( One cement : two coarse sand : four graded stone aggregate 20 mm ( twenty milimetre )nominal size ) of size 300x230x300 mm ( Three hundred into two hundred thirty into three hundred milimetre ) , including cost of necessary centring & shuttering & with approved expansion hold fasteners on cement concrete /reinforced cement concrete surface, including drilling necessary holes. Approved cramps/ pins etc. shall be welded to the frame work to support stone cladding,the steel work will be given a priming coat of zinc primer as approved by Engineer-in-Charge & painted with two or more coats of epoxy paint ( shop drawing shall be submitted by the contractor to the Engineer-in-Charge for approval before execution ). The frame work shall be fixed in true horizontial &vertical lines/planes. (Quantity structural steel frame work shall be measured for the purpose of payment ,stainless steel cramps shall be paid for separately & nothing extra shall be paid ), including all leads, lifts, & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing & similar works, including applying priming coat of approved steel primer mild steel tube/pipe, including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing aluminium work for doors, windows, ventilators & partitions with extruded built up standard tubular sections/ appropriate Z sections & other sections of approved make conforming to IS : 733 & IS : 1285, fixing with dash fasteners of required dia & size, including necessary filling up the gaps at junctions, i.e. at top, bottom & sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth,rust free, stright, mitred & jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per Architectural drawings & the direction of Engineer-in-Charge ( Glazing, panelling & dash fasteners to be paid for separately ) For fixed portion, Powder coatd aluminium ( minimum thickness of powder coating 50 micron ),including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing aluminium work for doors, windows, ventilators & partitions with extruded built up standard tubular sections/ appropriate Z sections & other sections of approved make conforming to IS : 733 & IS : 1285, fixing with dash fasteners of required dia & size, including necessary filling up the gaps at junctions, i.e. at top, bottom & sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth,rust free, stright, mitred & jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per Architectural drawings & the direction of Engineer-in-Charge ( Glazing, panelling & dash fasteners to be paid for separately ) For For shutters of doors, windows & ventilators including providing & fixing hinges/Pivots & making provision for fixing of fittings whereever required ,including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing glazing in aluminium doors, windows, ventilators shutters & partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the Atchitectural drawing & the direction of the Engineer-in-Charge ( Cost of aluminium snap beading shall be paid in basis item ) with float glass panes of 5mm ( five milimetre ) thickness ( weight not less than 12.50 Kg/Sqmt ), ( Tweelve point five zero kilogram per square metre ) including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Cement concrete flooring 1 : 2 : 4 ( One cement : two coarse sand : four graded stone aggregate ) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm ( forty milimetre ) thick with 20mm ( twenty milimetre ) nominal size ) stone aggregate including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Mirror polished Kotah stone slab flooring over 20 mm ( twenty milimetre ) ( average ) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing & polishing complete with base of cement mortar 1 : 4 ( one cement : four coarse sand ) 19 mm ( ninteen milimetre ) thick, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Mirror polished Kotah stone slab 20 mm ( twenty milimetre ) thick in risers of steps, skirting, dado & pillars laid on 12 mm ( twelve milimetre ) ( average ) thick cement mortar 1 : 3 ( One cement : three coarse sand ) & jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing & polishing complete, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08 % & conforming to IS 15622, of approved make, in all colours and shades, laid on 20 mm ( twenty milimetre ) thick cement mortar 1 : 4 ( One cement : four coarse sand ), jointing with grey cement slurry @ 3.3 Kg ( Three point three Kilogram ) per square metres including grouting the joint with white cement & matching pigments etc. complete size of tile 300 x 300 mm ( three hundred into three hundred milimetre ) , including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & laying vitrified double charge floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08 % & conforming to IS 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1 : 4 ( One cement : four coarse sand ), jointing with grey cement slurry @ 3.3 Kg ( three point three Kilogram ) per square metres including grouting the joint with white cement & matching pigments etc. complete size of tile 600 x 600 mm ( six hundred into six hundred milimetre ) , including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & laying vitrified double charge tiles in different sizes ( thickness to be specified by manufacturer ) , with water absorption less than 0.08 % & conforming to IS 15622, of approved make, in all colours and shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1 : 3 ( One cement : three coarse sand ), jointing with grey cement slurry @ 3.3 Kg ( Three point three Kilogram ) per square metres including grouting the joint with white cement & matching pigments etc. complete size of tile 600 x 600 mm ( six hundred into six hundred milimetre ) , including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing 10 mm ( ten milimetre ) thick acid and / or alkali resistant tiles of approved make & colour using acid and/or alkali resisting mortar bedding, & joints filled with acid and / or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in-Charge in flooring on a bed of 10 mm ( ten milimetre ) thick mortar 1 : 4 ( One cement : four coarse sand )Acid & alkali resistance tile, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing 10 mm ( ten milimetre ) thick acid and / or alkali resistant tiles of approved make and colour using acid and / or alkali resisting mortar bedding, and joints filled with acid and / or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in-Charge in dado/ skirting on 12 mm ( twelve milimetre ) thick mortar 1 : 4 ( One acid proof cement : four oarse sand ), Acid and alkali resistant tiles, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

40 mm ( forty milimetre ) thick fine dressed stone flooring over 20 mm ( average ) thick base of cement mortar 1:5 ( One cement : five coarse sand ), including pointing with cement mortar 1 : 2 ( One cement : two stone dust ) with an admixture of pigment to match the shade of stone , Red sand stone, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing and fixing on wall face PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion, Single socketed pipes complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- (i)110mm ( One hundred ten millimeter ) diameter metre.

Providing and fixing on wall face PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion, Single socketed pipes complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- (ii)75mm ( Seventy five millimeter ) diameter metre.

Providing and fixing on wall face PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- Bend 87.5° (i) 110mm ( eighty seven point five degree one hundred ten millimeter ) bend.

Providing and fixing on wall face PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- Bend 87.5° (ii) 75mm ( eighty seven point five degree Seventy five millimeter ) bend.

Providing and fixing on wall face PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- Shoe ( Plain )110mm ( One hundred ten millimeter ) shoe.

Providing & fixing mild steel holder bat clamps of approved design to cast iron or S.C.I. rain water pipes embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1 : 2 : 4 mix ( One cement : two coarse sand : four graded stone aggregate 20 mm nominal size ) & cost of cutting holes & making good the wall etc. 110 mm ( One hundred ten milmetre ) diameter PVC pipe including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing 0.60 mm ( sixty milimetre ) thick prepainted steel sheet in roofing TATA Durashine with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP ) organic coating of 20 ( twenty ) microns over 5 ( five ) microns primer coting to back coat of polyster of 5 ( five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6 mm ( six milimetre ) dia metre with prepainted limpet & rubber washers complete with all accessories as required as per the direction of Engineer-in-Charge, including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing ridge or hips 0.60 cm ( sixty centimetre ) over all with thick prepainted steel sheet in roofing TATA Durashine with hot dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 ( twenty ) microns over 5 ( five ) microns primer coting plus back coat of polyster of 5 ( five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6 mm ( six milimetre ) dia and prepainted G.I. limpet & rubber washers complete with all accessories as required as per the direction of Engineer-in-Charge, including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing valley 60cm overall 0.60 mm ( sixty milimetre ) thick prepainted steel sheet in roofing with TATA Durashinehot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 ( five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6 mm dia with prepainted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing flushing 38 cm ( thirty eight centimetre ) overall with 0.60 mm ( sixty milimetre ) thick prepainted sheet in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 ( twenty ) microns over 5 ( five ) microns primer coting plus back coat of polyster of 5 ( five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6 mm ( six milimetre ) dia and prepainted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing 30 cm ( thirty centimetre ) wide 120 cm ( one hundred twenty centimetre ) overall Box type prepainted TATA Durashine sheet gutter with iron bracket 40 x 3 mm ( forty into three milimetre ) size, bolts & nuts and washers etc. including making necessary connections with rain water pipes complete as per design. 0.45 mm ( forty five milimetre ) thick, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing flat iron bracket 50 x 3 mm ( Fifty into three milimetre ) size with necessary bolts, nuts & washers etc. for fixing galvanised steel sheets gutters with purlins including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing mild steel B.P. sheet 1.66 mm to 2 mm ( One point six six milimetre to two milimetre ) thick in eaves board/ facia/ soffits/ ceiling including cutting, fixing & welding to steel roof members & applying a coat of red lead primer complete as per the instruction of Engineer-in-Charge ( Base member of steel work shall be measured & paid for separately ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

15mm ( fifteen millimeter ) cement plaster on the rough side of single or half brick wall of mix : 1:6 ( one cement: six fine sand ) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

6mm ( six millimeter ) cement plaster of mix 1:4 (one cement : four fine sand) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & applying plaster of paris putty of 2 mm ( two milimetre ) thickness over plastered surface to prepare the surface even & smooth complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Distempering with oil bound washable distemper of approved brand & manufacture to give an even shade new work ( two or more coats ) over and including water thinnable priming coat with cement primer including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing walls with 100 % ( One hundred percent ) premium acrylic emulsion paint having VOC less than 50 ( fifty ) gram per litre UV resistance as per IS 15489: 2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade ( Company Depot Tined ) with silicon additives new work ( Two or more coats applied @ 1.43 ( One point four three ) Litre per 10 ( ten ) square metres over & including priming coat of exterior primer applied @ 0.90 ( Ninety ) litre per 10 ( ten ) Square metres, including all leads, ,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge .

Finishing walls with Acrylic smooth exterior paint with of required shade new work ( two or more coat ) applied @ 1.67 litre/10 Sqmt ( one point six seven litre per ten square metres ) over & including priming coat of exterior primer applied @ 2.20 Kg /10 Sqmt ( at the rate two point two zero kilograme per ten square metre ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10sqm ( zero point nine zero litre per ten square meter ) over an under coat of primer applied @0.75 ltr/10 sqm ( zero point seven five litre per ten square meter )of approved brand and manufacture complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10sqm( zero point nine zero litre per ten square meter ) over an under coat of primer applied @ 0.80 ltr/ 10sqm( zero point eight zero litre per ten square meter ) of approved brand and manufacture complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing 1200*1500mm (One thousand two hundred into one thousand five hundred milimetre) size 12mm (Twelve milimeter) thick green chalk board (Non magnetic) with superior quality framing specially anodized aluminum profile 20*15 mm (Twenty into fifteen milimeter) with corner of black surface shall be non porous ceramic particals on the top green surfaces for smooth writting with chalk over 11 mm (Eleven milimeter)thick partical board which shall have backing materials of galvinised sheet 0.28 mm (Zero piont two eight milimeter) thick approx. The board shall be fixed on the wall with specially designed J clump and square clump with the help nylon sleves and screwa as per the site requirement complete in all respect as per drawing, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm ( one hundred millimeter ) sand cast Iron P or S trap, 10 litre ( ten litre ) low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge: White Vitreous china Orissa pattern W.C. pan of size 580mm x 440mm ( five hundred eighty millimetre X four hundred forty millimeter ) with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10litre ( ten litre )low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- W.C. pan with ISI marked white solid plastic seat and lid.

Providing & fixing white Vitreous China flat back half stall urinal of size 580 x 380 x 350 mm ( five hundred eighty into three hundrded eighty into three hundred fifty milimetre ) with white PVC auotmatic flusing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with union & clamps ( all in C.P. brass ) with waste fitting as per IS : 2556, C.I. trap with out let grating & other couplings in C.P. brass, including painting of fittings & cutting & making good the walls & floors wherever required Range of two half stall Urinals with 5 litre P.V.C. automatic flushing cistern, including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15mm ( fifteen millimeter ) C.P. brass pillar taps, 32mm ( thirty two millimeter ) C.P.brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- White Vitreous China wash basin size 550mm x 400mm ( Five hundred fifty millimeter into four hundred millimeter ) with single 15mm ( fifteen millimeter ) C.P. Brass pillar tap .

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing stainless steel A ISI 304 ( 18/8 ) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm ( forty milimetre ) including painting of fittings & brackets, cutting & making good the walls wherever required kitchen sink without drain board 810 x 450 mm ( Eight hundred ten into four hundred fifty milimetre ) bowl depth 200 mm, ( Two hundred milimetre ) including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing white vitreous China Laboratory sink with Cast iron brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste & 40 mm C.P. brass trap with necessary C.P. brass unions complete, including paintingh of fittings & brackets, cutting & making good the walls wherever required size 600 x450 x 200 mm, including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge

( 89.02) Providing & fixing stainless steel A ISI 304 ( 18/8 ) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm ( forty milimetre ) including painting of fittings & brackets, cutting & making good the walls wherever required kitchen sink without drain board 460 x 385 mm ( Four hundred sixty into three hundred eighty five milimetre ) bowl depth 200 mm, ( Two hundred milimetre ) including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing and fixing 600mm x 450mm ( Six hundred millimeter into four hundred fifty millimeter ) beveled edge mirror of superior glass (of approved quality) complete with 6mm ( six milimetre ) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing 600mm x 120mm x 5mm ( Six hundred millimeter into one hundred twenty millimeter into five millimeter ) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm ( forty millimeter ) long screws, rawl plugs etc., complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing C.P. brass toilet paper holder complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing PTMT liquid soap container 109mm ( one hundred nine millimeter ) wide, 125mm( one hundred twenty five millimeter ) high and 112mm( one hundred twelve millimeter ) distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105gms ( one hundred five grams ) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providuing & fixing PTMT towel rail complete with brackets fixed to wooden cleats with C.P. brass screws with concealed fittings arrangement of approved quality & colour, 450 mm ( Four hundred fifty milimetre ) long towel rail with total length of 495 mm, 78 mm ( Four hundred ninety five milimeter, seventy eight milimetre ) wide & effective height of 88 mm ( eighty eight milimetre ) , weighting not less than 170 ( One hundred seventy ) grams including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

(95.01) Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre ( one metre ) spacing. This includes testing of joints complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 1216 (16 mm ( sixteen millimeter ) OD) pipe.

(95.02) Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre ( one metre ) spacing. This includes testing of joints complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:-1620 (20mm ( twenty millimeter ) OD) pipe.

(96.01) Providing and fixing G.I. pipes complete with G.I. fittings & Clamps including making good the walls etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting & making good the walls including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. internal work:-15mm ( fifteen millimeter ) dia nominal bore.

(96.02) Providing and fixing G.I. pipes complete with G.I. fittings including making good the walls etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting & making good the walls including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. internal work :- 20mm ( twenty millimetre ) dia.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.External work:-15mm ( fifteen millimeter ) dia nominal bore.

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 25 mm to 40mm ( twenty five millimeter to forty millimeter ) nominal bore.

Fixing water meter & stop cock in G.I. pipe line including cutting & threading the pipe & making long screws etc. complete ( Cost of water meter & stop cock to be paid separately ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

Providing and fixing C.P. brass stop cock ( Concealed ) of standard design & of approved make conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

Providing and fixing C.P. brass angle valve for basin mixer & geyser point of approved quality conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

(104.01)Providing & fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete 150mm dia ( One hundred fifty milimetre ) including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(104.02) Providing & fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete 100 mm ( One hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(104.03) Providing & fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(105.01) Providing & fixing PVC door bend with oval access door, insertion rubber washer 3 mm ( three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 150 mm ( one hundred fifty milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(105.02) Providing & fixing PVC door bend with oval access door, insertion rubber washer 3 mm ( three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 100 mm ( one hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

( 105.03) Providing & fixing PVC door bend with oval access door, insertion rubber washer 3 mm ( three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(106.01) Providing & fixing PVC collars ISI marked including fixing with approved adhesive etc. complete 150 mm ( One hundred fifty milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(106.02) Providing & fixing PVC collars ISI marked including fixing with approved adhesive etc. complete 100 mm ( One hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(106.03) Providing & fixing PVC collars ISI marked including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(107.01) Providing & fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete 150 mm ( One hundred fifty milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(107.02) Providing & fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete 100 mm ( One hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(107.03) Providing & fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(108.01) Providing & fixing PVC double equal branch with oval access door, insertion rubber washer 3mm ( Three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 150 mm ( One hundred fifty milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(108.02) Providing & fixing PVC double equal branch with oval access door, insertion rubber washer 3mm ( Three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 100 mm ( One hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

( 108.03) Providing & fixing PVC double equal branch with oval access door, insertion rubber washer 3mm ( Three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(109.01) Providing & fixing PVC clamps ISI marked of approved design with steel screws & rawal plugs etc. complete 150 mm ( One hundred fifty milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(109.02) Providing & fixing PVC clamps ISI marked of approved design with steel screws & rawal plugs etc. complete 100 mm ( One hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(109.03) Providing & fixing PVC clamps ISI marked of approved design with steel screws & rawal plugs etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

( 110.01)Providing & fixing PVC reducer ISI marked including jointing with approved adhesive etc. complete 150 mm x 110 mm ( One hundred fifty milimetre into one hundred ten milimetre ) dia, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(110.02) Providing & fixing PVC reducer ISI marked including jointing with approved adhesive etc. complete 110 mm x 75 mm ( One hundred ten milimetre into seventy five milimetre ) dia, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

(111.01) Providing & fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting & making good the wall & floors etc. complete 110 mm x 90 mm ( One hundred ten milimetre into ninety milimetre ), including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

( 111.02) Providing & fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting & making good the wall & floors etc. complete 110 mm x 75 mm ( One hundred ten milimetre into seventy five milimetre ), including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing 15 mm ( fifteen milimetre ) mixer for kitchen sink with top/ bottom swining spouts, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20mm ( twenty millimeter ) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40mm ( forty millimeter ) nominal size), inside plastering 12mm ( twelve millimeter ) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20mm ( twenty millimeter ) nominal size) finished with a floating coat of neat cement complete as per standard design complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. : Inside size 90cm x 80cm and 45cm ( Ninety centimeter into eighty centimeter and forty five centimeter ) deep including C.I. cover with frame (medium duty) 455 x 610 mm ( Four hundred fifty five into Six hundred ten millimeter ) internal dimensions, total weight of cover and frame to be not less than 38 kg ( thirty eight kilogram ) (weight of cover 23 kg ( twenty three kilogram ) and weight of frame 15 kg( fifteen kilogram ) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.50.

Cutting holes to 30 x 30 cm in walls including making good the same with common burnt clay F.P.S. ( Non modular ) bricks, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing 8 mm ( eight milimetre ) dia C.P./S.S. Jet with flexible tube upto 1.00 ( One ) metre long with S.S.triangular plate to Eureopean type W.C. of quality & make as approved by Engineer-in-Charge, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

(116.01) Providing & fixing in position precast reinforcement coment concrete manhole cover & frame of required shape & approved quality LD- 2.5 ( Two point five ) rectangular shape 600 x 450 mm ( six hundred into four hundred fifty milimetre ) internal dimensions including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

(116.02) Providing & fixing in position precast reinforcement coment concrete manhole cover & frame of required shape & approved quality LD- 2.5 ( Two point five ) square shape 450 mm ( four hundred fifty milimetre ) internal dimensions including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Supplying & filling brick bats in dispension trenches ( Brick aggregate ( Single size ) 50 mm ( Fifty milimetre ) nominal size ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing weep holes in brick/ stone masonry, plain/ reinforced concrete abutment, wing wall return walls with 100 mm ( One hundred milimetre ) dia PVC pipe extended through the full width of the structure with slope of 1 (V) : 20 (H) towards drawing face complete as per drawing & technical specification clause 614,709,1204, 3.7 including all leads, lifts & carriage of materials complete as per entire satisfaction of the Engineer-in-Charge.

Preparation of Sub-grade by dressing to camber ( Earth work for the cutting involved for Sub-grade to be paid for separately depending upon the classification of soil complete as per HP.PWD.,specification including all leads, lifts lifts & carriage of materials complete as per entire satisfaction of the Engineer-in-Charge.

Consolidation of Sub grade with road roller including making good the undulation etc. with earth or quarry soil etc. & rolling the Sub-grade complete as per HP.PWD., specification including all leads, lifts lifts & carriage of materials complete as per entire satisfaction of the Engineer-in-charge

Stone soling properly hand packed filling interstices with Kharunja & consolidating with power road roller to the required gradient & camber including spreading watering & rolling of binding materials moorum or earth etc. complete as per HP.PWD., specification. 150 mm spread thickness ( finished work including materials & labour ) including all leads, lifts lifts & carriage of materials complete as per entire satisfaction of the Engineer-in-charge

Providing, laying, spreading and compacting stone aggregate of specific size to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 KN static roller in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density grading-2,as per Technical Specification clause 405 by mechnical means including carriage of materials within leads, lifts and other incidential complete as per entire satisfaction of the Engineer-in-Charge.

Providing & laying reinforced cement concrete pipe NP2 for culvert on first class bedding of granular materials in single row including fixing collar with cement mortar 1 : 2 ( One cement : two coarse sand ) but excluding excavation, protection work, back filling, concrete & masonry work in head walls & parpets clause 1108. 900 mm ( Nine hundred milimetre ) dia pipe NP2 including all leads, lifts, cariage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & laying flooring laid over cement concrete bedding complete as per drawing & technical specification clause 1303, Rubble stone laid in cement mortar 1 : 3 ( One cement : three coarse sand ), including carriage of materials within all leads, lifts & entire satisfaction of the Engineer-in-Charge.

Om Parkash Sharma

rajesh kumar suman

H. C. Bansal Engg. & Contt.