SPL REPAIRS TO BLDG NO T-13 AND REV WORKS AT NAA UNDER GE (N) TEZPUR

Amount

Dismantling of Asbestos cement(corrugated, semi corrugated etc.) sheet in roof coverings complete all as specified and as directed.

Dismantling of floor/ wall tiles including cement mortar bedding of any thickness upto PCC/ RCC/brick surface and rubbish off the premises, complete in all respect all as specified and directed.

Dismantalling of cement concrete (unreinforced) in ground floors and pavings not exceedings 15 cm thickness (below or above ground level), complete in all respect as specified and directed.

Taking down wooden door shutter area exceeding 1.00 but not exceeding 2.00 sqm each complete all as specified and as directed.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 sqm each complete all as specified and as directed

Demolition and breaking up drain pipes 75 mm/110 mm bore dia (Salt glazed ware, PVC or Reinforced concrete) set in cement mortar, complete in all respect as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height. Complete all as specified and as directed.

M & L for mild steel TMT bars any dia in stirrups, spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed

M & L for RCC M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M & L for RCC M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and as directed.

M & L for RCC M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and as directed.

M & L for RCC M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate as in chajjas complete all as specified and as directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surfaces of concrete complete all as specified and as directed.

M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete complete all as specified and as directed.

M & L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete complete all as specified and as directed.

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 10 cm but not exceeding 20 cm wide for rough finished surfaces of concrete complete all as specified and as directed.

S&F steel work in tubular/square/rectangular hollow section/angle iron, tee etc. for structural trusses including special shaped washer etc. complete using ERW or induction butt welded tubes using Fe as per IS 4923, Grade YST 310 including necessary machinery for upto 10m height structure complete in all respect as specified and directed.

Material and labour for brick work with sub-class "B" old size bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar (1:6) including dismantling of existing brick work built in cement mortar complete in all respect as specified and directed.

M&L for half brick work with subclass ‘B’ old size bricks of class designation 75, straight or curved on plan exc. 6m mean radius built in CM (1:4) including dismantalling of brick work built in cement mortar in any position, complete in all respect as specified and directed.

S&F rolled section as in framing for door/vent/CB/chowkhats, wind tie and the like using angle, tee, hollow tubes etc., cleat and connecting plates complete (Butt hinges shall be measured and paid for separately) using Fe 410-W (Gde-E-250) quality "A" complete all as specified and directed.

S & F second class hardwood plain,solid ,straight,chowkats and frames,wrought, framed rebated on the solid ,rounded or chamfered,put together with glue pinned at joints, complete in all respect as specified and directed.

M & L for cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs, slab staging for water tanks, filling of pressed steel door frame, fixing of hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formworks complete all as specified and directed by Engineer- in-charge.

S&F coloured 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based trapezoid profile steel sheet having tensile strenght of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws with bitumen washer to truss members of any material, complete in all respect as specified and directed.

M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed.

M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed.

S&F exposed GI powder coated snap grid frame work for false ceiling in flat or in sloping, of grid size 600 x 600 mm comprising of wall/ cleat angle of size 25x25x0.35 mm and corss tee of size 24x38x0.70 mm with 4 mm dia GI wire as suspender and including 4 mm thick decorative pre-painted non asbestos board (E-Board) in false ceiling including fixing arrangement from steel/ wooden truss of any type including dismantling of existing false ceiling boards, complete in all respect as specified and directed. (Make:- Eternit, Everest or equivalent)

Providing and laying skid/non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick screed bed in cement mortar (CM) 1:6, complete in all respect as specified and directed.

Providing and laying coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.08 sqm but not exceeding 0.15 sqm, in skrting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick rendering in cement mortar (CM) 1:4, complete in all respect as specified and directed.

M&L for any colour of granite stone without white spots Granite stone slab 17 to 19 mm thick, as in floor, dado, steps, laid over and including screed bed 15 mm thick in cement mortar (CM) 1:6, jointed and pointed with white cement mixed with pigment to match the shade of stone including cuttingl rubbing and polishing surface, including cutting for wash hand basin, sink, gas pipe hole etc., to the entire satisfaction of the Engineer-in-Charge, complete in all respect as specified and directed.

M & L for rendering/plastering 15 mm thick in cement mortar 1:4 on faces of brick or concrete surfaces and finished the surface even and smooth without using extra cement complete in all respect as specifified and directed.

M & L for rendering/plastering 15 mm thick in cement mortar 1:6 on faces of brick or concrete surfaces and finished the surface even and smooth without using extra cement complete in all respect as specifified and directed.

Supply only integral water proofing compound complete all as specified and as directed.

S&F in repair 15 mm bore GI tubes medium grade, galvanished with all fittings fixed complete to walls and ceiling or laid in floors complete in all respect as specified and directed.

S&F in repair 20 mm bore GI tubes medium grade, galvanished with all fittings fixed complete to walls and ceiling or laid in floors complete in all respect as specified and directed.

S & F in repairs 20 mm gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed to pipe complete all as specified and directed.

Providing and fixing in position kitchen cup board box type as per design and directed of 550-600mm deep, fixed over wall with PVC gittie and screws/or in beneath of kitchen counter, cup board, kitchen cabinet in required sizes as per site made out of 17-18mm thick one side decorative lamination and other side balancing lamination sheet consisting of carcass 17-18mm thick PVC sheet. Provision of shelves, shutters, back side, top, bottom, side, made out of 17-18mm thick one side decorative laminated PVC sheet , all required brackets, screws etc,. The panel shall be fabricated using adhesives and screws whereever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per maufactures specifications and drawing including 15mmX20mm medium grade chrome finish two nos per leaf, slip on cabinet hinge/self-closing hinge, soft close hydraulic 4 hole cabinet auto cup hinge full overlay O crank with soft closing of make Godrej/Avis L Bihari/Hettich/Harrison and 50mm SS handle size all items each per shutter including taking down of existing box complete in all respect as specified and directed. Make: Rajshri Plastiwood, Sintex or of appd make. (Note: For payment, measurement shall be taken as front portion of cup board measurement only, rest other items/materials as specified shall not be measured or paid as these are included in this item)

Providing and fixing in position kitchen cup board box type as per design and directed of 250-300mm deep, fixed over wall with PVC gittie and screws/or in beneath of kitchen counter, cup board, kitchen cabinet in required sizes as per site made out of 17-18mm thick one side decorative lamination and other side balancing lamination sheet consisting of carcass 17-18mm thick PVC sheet. Provision of shelves, shutters, back side, top, bottom, side, made out of 17-18mm thick one side decorative laminated PVC sheet , all required brackets, screws etc,. The panel shall be fabricated using adhesives and screws whereever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per maufactures specifications and drawing including 15mmX20mm medium grade chrome finish two nos per leaf, slip on cabinet hinge/self-closing hinge, soft close hydraulic 4 hole cabinet auto cup hinge full overlay O crank with soft closing of make Godrej/Avis L Bihari/Hettich/Harrison and 50mm SS handle size all items each per shutter including taking down of existing box complete in all respect as specified and directed. Make: Rajshri Plastiwood, Sintex or of appd make. (Note: For payment, measurement shall be taken as front portion of cup board measurement only, rest other items/materials as specified shall not be measured or paid as these are included in this item)

S & F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. or for window grill of appd size and shapeincluding fixing with aluminium "U" shape section for fixing etc. complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F powder coated aluminium three tier window frame including necessary joining cleats, of Jindal section No 20832 or equivalent section of appd make of 1.5mm thick complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F powder coated aluminium window and ventilator shutters, side hung type with/without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, EPDM rubber packing (of 50 No) grade), powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21, 100mm long (2 no.) suitable handle (1 no.) complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F powder coated aluminium sliding window with/without sash bars, aluminium sections of thickness 2mm including necessary joining cleats, glazing clips, EPDM rubber packing (of 50 No grade), powder coated aluminium snap beading, screws, center grooved stainless steel ball-bearing double roller 2 position height adjustment, sound/dust brush, recessed handle with locking arrangement complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F 65 mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and as directed.

S & F 75 mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and as directed.

S & F 100 mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and as directed.

Supply and fix solid PVC door frames of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube all as per specification & drawing complete all as specified and directed by Engineer in charge.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel haivng a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and botom rail on either side & as gap insert for top rail & bottom rails; Panelling of plain colour PVC sheet to be fitted in the M.S. frame weloded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling and fixing in the frame at site as per specification & drawing, complete in all respcet as specified and directed.

S&F 35mm thick second class HW glazed and skeleton shutters, open rebated and prepared to receive glass gauge etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass etc.; sizes of members of shuttrs as specified in SSR Part-I, section 8, clause 8.24 (a), complete in all respect as specified and directed.

S & F 4 mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in square not exceeding 0.5 sqm in each pane complete all as specified and as directed.

Supply & fix sheet glass, ordinary quality, 4 mm thick and glazed with oil putty or fixed with beads in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

S & F flush door shutters, 25 mm thick, solid core of block boards construction, MR grade, commercial type with stiles, rails and lipping of timber as given in Group 2A and Group 2B of Annex B of IS 2202 (Part 1): 1999, both sides face panels of plywood as per IS 710: 2010, internally lipped complete all as specified and as directed.

S & F flush door shutters, 35 mm thick, solid core of block boards construction, MR grade, commercial type with stiles, rails and lipping of timber as given in Group 2A and Group 2B of Annex B of IS 2202 (Part 1): 1999, both sides face panels of plywood as per IS 710: 2010, internally lipped complete all as specified and as directed.

S & F 18-19mm block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work including necessary leaping/edge margin of 3mm thick complete in all respect as specified and directed.

S & F aluminium barrel tower bolts with barrel and bolt of extruded sections of aluminium alloys, 200 mm long, anodized finish not be less than Grade AC 10 of IS 1868 : 1996 with transparent anodic film complete all as specified and as directed.

S & F cast aluminium alloy handle, cast type, 125 mm size, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed.

S & F mild steel sliding door bolts, type I (plate type), size 250 mm, stove enamelled black finish to back plate, straps and staple, electroplated finish with nickel and chromium to hasp and bolt, bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed.

S & F mild steel door spring of rat tail type of size 300 mm, bright finish including roller and roller plate complete all as specified and as directed.

S & F 20 mm dia harrison rails, anodised aluminium alloy with fixing brackets, stops, rollers etc. complete all as specified and as directed.

S&F 350 x 450 mm size, PVC mirror cabinet complete all as specified and directed. Make:- Prayag cat Part No 551, CERA, Hindware, Jaquar

S&F plate rack made out of stainless steel sheet 0.50 mm thick overall size 900 mm (W) x 760 mm (H) x 250 mm (D) with three shelf, complete in all respect as specified and directed

S&F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to drarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm, complete in all respect as specified and directed. Make : Jayna, Neelkhanth, Nirali

S&F three layered white in colour rotational moulded made out from LLDPE material water storage tanks of capacity 1000 ltr (cylindrical vertical with closed top) including three tank nipples of 20 mm nominal bore dia hoisted and fixed in position including dismantling/ taking down all as specified in SSR part I, complete in all respect as specified and directed. Make:- Sheetal (Virat), Sintex, Oriplast, Supreme

S & F PTMT ball valve high pressure 20mm bore with epoxy coated aluminium rod & high density plastic ball screwed for iron/CPVC pipe/fittings complete all as specified and directed.

S & F in repairs 15 mm nominal size, nonrising spindle type fancy concealed stop valves as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed

S&F in repair vitreous china wash down water closet pan (padestal pattern) white including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated hinging device (exclusive flushing cistern and flush pipe), complete in all respect as specified and directed.

S&F in repair PVC valveless, syphonic action type, low level dual flush cistern 10 ltr capacity, white, wtih inlet, ball valve, float and handle including brackets & flush pipe of polyethylene for low or high level cistern of required height of high density PVC, 32 mm dia pipe, complete in all respect as specified and directed.

S & F for 15mm size PVC connection pipe with PTMT nut of length 450mm complete all as specified and directed.

S&F in repairs 15 mm bore fancy type CP finished angle valves, cast copper alloy, screwed down, high pre-ssure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete in all respect as specified and directed.

S&F in repairs long body Bib taps of 15 mm bore, fancy type CP finish cast copper alloy with crutch handle, screwed down, screwed for iron pipes, complete in all respect as specified and directed.

S&F in repairs short body Bib taps of 15 mm bore, fancy type CP finish cast copper alloy with crutch handle, screwed down, screwed for iron pipes, complete in all respect as specified and directed.

Supply and fixed in repair 15mm bore, cast ABS body, CP finish, shower rose of size 125 mm dia and shower arm of cast copper alloy CP finished, fixed to iron pipe/fiitings complete in all respect as specified and directed.

S & F brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and as directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with brass chromium plated bracket guard and railing 60 cm long complete in all respect as specified and directed.

S&F in repair wash hand basins (WHB), vitreous china of size 550x400 mm (flat back or angle back type), including cutting for and pinning in ends of brackets over new angle iron erecting stand embedded in PCC (1:2:4) block including 32 mm dia bore waste fittings cast copper alloy chromium plated with long screwed shanks and flynuts flange and beded in redlead cement, PVC waste pipe including 15 mm bore dia fancy type CP finish Pillar tap, cast copper alloy with capstand heads, screw down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screw for iron pipes complete in all respect as specified and directed.

S&F in repair Health faucet ABS SS braided hose 1 mtr with V hook including fixing arrangement, complete in all respect as specified and directed. Make:- Hindware, Cat Part No. F160068IV), or equivalent make of Cera, Perryware.

S & F PVC (SWR) nahani trap of 75mm outlet dia fixed with PVC 150X150mm size openable at center grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S & F PVC (SWR), type A as per IS 13592: 2013 single socketed rain water pipes in any length with rubber ring joints, 110 mm dia, fixed to walls complete all as specified and as directed.

S & F PVC (SWR), type A as per IS 13592: 2013 single socketed rain water pipes in any length with rubber ring joints, 75 mm dia, fixed to walls complete all as specified and as directed.

S & F PVC (SWR), type B as per IS 13592: 2013 single socketed soil waste pipes in any length with rubber ring joints, 110 mm dia, laid in trenches complete all as specified and directed.

S & F PVC (SWR), type B as per IS 13592: 2013 single socketed soil waste pipes in any length with rubber ring joints, 75 mm dia, laid in trenches complete all as specified and directed.

S & F PVC (SWR) Tee(87.5⁰) single, 110 mm dia with inspection door conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge.

S & F PVC (SWR) Tee(87.5⁰) single, 75 mm dia with inspection door conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge.

S & F PVC (SWR) bends without inspection door (any angle), 110 mm dia conforming to IS 14735: 1999 complete all as specified and directed.

S & F PVC (SWR) bends without inspection door (any angle), 75 mm dia conforming to IS 14735: 1999 complete all as specified and directed.

S & F PVC (SWR) vent cowl, 110 mm dia conforming to IS 14735: 1999 complete all as specified and as directed.

S & F PVC (SWR) vent cowl, 75 mm dia conforming to IS 14735: 1999 complete all as specified and directed.

Supply and fixed unplasticised PVC (SWR) Gully trap 125/110 mm, setting and jointing with solvent cement complete in all respect as specified and directed. Make: Supreme, Prince, Oriplast.

M&L for precast RCC, type B-1, 1:2:4 (using 20 mm crushed and graded stone aggregate) as in manhole covers/ cover slabs or of similar type slab works, etc. incl necessary formwork and loading/ unloading of the same and fixed in position, complete in all respcet as specified and directed.

M & L for RCC M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for plinth protection or in foot path of 75 mm thick of cement concrete using type C-1, 1:3:6 (using 20 mm nominal size crushed and graded stone aggregate) in alternate penals and finished fair and even complete in all respect as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of weather coat over 2 mm thick wall care putty over a coat of primer including necessary preparation of surface, complete in all respect as specified and directed.

Material and labour for preparation of newly undecorated plastered surface of wall and applying two coats of oil bound distemper and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2mm thick (in two layers), wall care putty complete in all respect as specified and directed.

M & L for preparation of new or previously untreated wood or wooden surfaces, of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Preparation of newly or previously untreated steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge

Providing and laying Coloured Vitrified tiles 10 mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white cement with pigment to match the tile colour over 15mm thick screed bed in cement mortar (1:4) complete in all respect as specifified and directed.

Providing and laying coloured Vitrified tiles 10 mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm, in skirting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15mm thick rendering in cement mortar (1:4) complete in all respect as specifified and directed.

S&F tower ring of copper alloy CP finished complete all as specified and directed. Make:- Jaquar cat part No AEC-1121, Make Hindware cat part No F450023

Taking down cement plaster on stone/brick/concrete surfaces including racking out joint, hacking for key, scrubbing down with water etc, complete all as specified and as directed.

M & L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and as directed.

S&F towel rack 600mm long of cast copper alloy, chromium plated with end brackets complete in all respect as specified and directed.(cat part no-AHS-CHR-1581H)

M&L preparation of untreated new steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M & L for screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and as directed.

M & L for coloured non - skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement with pigment to match the tile colour complete in all respect as specified and directed.

M & L for coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.72 Sqm, in dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile colour complete in all respect as specified and directed.

S&F in repair Health faucet cast coper alloy CP finish 15 mm dia fancy type with brass plated flexible hose and wall hook, 1.00 mtr complete, in all respect as specified and directed. Make:- Jaquar, Hindware Cat part No F-160002

S&F CP finish cast copper alloy, two way bib cock complete in all respect as specified and directed.. Make:- Make:- Jaquar cat part No ALI-CHR-85041

S&F in Exposed Part Kit of Single Lever Basin Mixer Wall Mounted Consisting of Operating Lever, Cartridge Sleeve, Wall Flange, Nipple & Spout (Compatible with ALD-233N & ALD-235N) complete in all respect as specified and directed. Make:- Jaquar (cat part : (ALI-CHR-85233NK ).

S&F in Concealed Body for Single Lever Basin Mixer Wall Mounted, But without Exposed Parts complete in all respect as specified and directed. Make:- Jaquar (cat part : (ALD-CHR-233N ).

S&F in repair Bathtub Spout with Button Attachment For Hand Shower With Wall Flange complete in all respect as specified and directed. Make:- Jaquar (cat part : (SPJ-CHR-85463 ).

S&F in repair Exposed Part Kit of Single Lever Hi Flow In-wall Diverter (Compatible In-wall part ALD-079N is sold separately) complete in all respect as specified and directed. Make:- Jaquar (cat part : (ALI-CHR-85079NK ).

S&F in repair Alive Maze Hand Shower 68x100mm Round Edge & Rectangular Head Single Flow(Face Plate Stainless Steel & ABS Body in Chrome finish) with Rubit Cleaning System complete in all respect as specified and directed. Make:- Jaquar (cat part : (HSH-CHR-85537 ).

S&F in repair Premium Wall Bracket For Hand Shower, ø35mm & 100mm Long Round Shape complete in all respect as specified and directed. Make:- Jaquar (cat part : SHA-CHR-555 ).

S&F in repair Flexible Tube 8mm dia & 1.5M Long with Nuts complete in all respect as specified and directed. Make:- Jaquar (cat part : (SHA-CHR-549D8 ).

S&F in repair Concealed Body for Single Lever High Flow Diverter with Button Assembly, But without Exposed Parts complete in all respect as specified and directed. Make:- Jaquar (cat part : (ALD-CHR-079N ).

S&F in repair Shower Arm Straight ø 20mm & 450mm Long Round Shape without Bend For Wall Mounted Showers with Flange complete in all respect as specified and directed. Make:- Jaquar (cat part : (SHA-CHR-49483 ).

S&F in repair Alive Maze Overhead Shower 200X300mm Round Edge & Rectangular Head Single Flow (Body & Face Plate Stainless Steel) with Rubit Cleaning System complete in all respect as specified and directed. Make:- Jaquar (cat part : (OHS-ACR-85859M ).

S & F brass barrel tower bolts with barrel of extruded sections of brass and rolled or down brass, 300 mm long, bright finish complete all as specified and as directed.

S & F brass sliding door bolts with sand-cast brass hasp, staple and fixing bolts or clips and rolled or drawn brass bolts (type-1) or Brass sliding door bits with diecast brass hasp, staple and fixing bolts or clips and rolled or drawn brass bolts (type -2), satin finish or polished, 300 mm long complete all as specified and as directed.

S & F butt hinges, cast brass with galvanised mild steel wire pin, bright finished, hinge designation 100B11 as per IS 205: 1992 complete all as specified and as directed.

S & F rotational moulded polyethylene double layer water tanks (vertical cylindrical with close top) as per IS 12701: 1996 of 1000 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes all as specified and as directed.

S&F in repair for 15 mm bore pipe brass chromium plated (CP) shower 300 x300 mm size, fixed to iron pipe, complete all as specified and directed.make- Jaquar

S & F powder coated aluminium ventilator with half portion louvered (adjustable)with 4mm thick glass in louver and balanced portion fixed 4mm thick frosted glass glazing including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings complete in all respect as specified and directed.

S & F PVC (SWR) Tee(87.5⁰) single, 110 mm dia without inspection door conforming to IS 14735: 1999 complete all as specified and directed.

S & F PVC (SWR) Tee(87.5⁰) single, 75 mm dia without inspection door conforming to IS 14735: 1999 complete all as specified and as directed.

Supplying & laying in trenches 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Supplying & laying in trenches 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

S & F 20 mm gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed to pipe complete complete all as specified and as directed.

S&F corner Sheet glass shelf assembly consisting of 5.5mm thick corner sheet glass shelf with chromium plated brass brackets complete all as specified and directed.make-jaquar(cat part no-ACN-CHR-1173)

S&F in repair Counter Top Basin, Size: 600x400x185 mm including Waste coupling 32 mm SS and Bottle Trap 32mm Size with 300mm & 190mm Long Wall Connection Pipes & Wall Flange , complete in all respect as specified and directed. Make:- Jaquar, Cat Part No. SLS-WHT-6601,

S&F in repair table top wash hand basins (WHB), vitreous china of size 500x400 mm x 150 mm ,Waste coupling 32 mm SS and PVC waste pipe including 15 mm bore dia fancy type CP finish swan neck basin mixer, cast copper alloy with capstand heads, screw down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screw for iron pipes complete in all respect as specified and directed. Make:- Jaquar, Cat Part No. JDS-WHT-25909 (TT WHB), Cat Part No FLR-CHR-5167NB (Swan neck basin mixer) including 20mm granite table top size(1.0 mtr x 0.6 mtr) and cabinet front side views material made by pre laminated 18 mm thick HDHMR board for long life.2 drawers and 1 door space.hardware ss auto closed hinges joints door diamond shape drawers handle,ss drawers channels for smoothly open and close the drawers complete all as specified and directed.

S&F 15mm bore dia CP finish , bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron/CPVC pipe/fittings or for brass ferrule including cup washer/flange(Make-Jaquar cat part no-ALI-85037) complete all as specified and directed.

S & F 15 mm nominal size, nonrising spindle type fancy stop valves as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed.

S&F in repair Rimless Single Piece WC With UF Soft Close Slim Seat Cover, Hinges, Dual Flush Cistern Fitting, Fixing Accessories And Accessories Set, Size: 385x720x710 mm, S Trap- 300 mm cat part no-ONS-WHT-10853S300UFSM complete in all respect as specified and directed.

S & F toilet paper holder of vitreous china, box type, white fixed to walls with chromium plated brass screws complete all as specified and as directed.

S & F Liquid soap container of frosted glass fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) complete in all respect as specified and directed.

Material and labour for complete removal of existing treatment on wall and applying two coats of oil bound distemper and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2mm thick (in two layers), wall care putty complete in all respect as specified and directed.

S&F towel ring of copper alloy CP finished complete in all respect as specified and directed. Make:- Jaquar cat part No AEC-1121, Make Hindware cat part No F450023

S&F Itched toughened frosted glass 12mm thick for partition and door fixed with stainless steel hinges ,handle and stainless steel fixing cleat complete in all respect as specified and directed.

S & F Stainless Steel Palo Shower Water Drain Channel/Waste Water Floor Drain with Stainless Steel Trap and Side Hole with Collar with min size 600 x100mm complete in all respect as specified and directed.

S&F sun control fim,dark shade film, frosted films suitable for widnows, door and paritions n exc 0.5 sq.m in each pane, complete in all respect as specified and directed.

Providing & laying heavy duty non skid coloured digital printed floor tiles of size 300mmX300mm ,8 to 10mm thick set and jointed in neat cement slurry and pointed with white cement with pigment to match the tiles colour over and including 15mm thick screed bedding in cm 1:6 and dismentling of existing tiles/blocks of any discription complete in all respect as specified and directed. make-somany(heavy duty),johnson (Endura), Orient Bell(Pavers)

Supply and fix PVC SWR Nahani/ Floor trap plain with grating including jointing with solvent cement, dia of outlet 75 mm, water seal minimum 50 mm, complete all as specified and directed by Engineer in charge.

M & L for RCC M25 (Design Mix) using 20 mm nominal size graded crushed stone aggregate as in arches complete all as specified and as directed.

M&L for coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile colour complete in all respect as specified and directed.

S&F Vitreous China urinals, full stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern complete all as specified and directed.

M & L for Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles complete in all respect as specified and directed.

Taking down carefully old burnt u/s aluminium / copper point wiring for one light , fan, socket /power socket point or buzzer controlled by one switch complete including fitting / fixtures such as switches, ceiling roses, holder, socket, light fitting etc; and making good disturbed surfaces of walls, ceilings etc all as specified.

M & L for point wiring with 1.5 sqmm FRLSH, PVC insulated stranded copper conductor single core including non metalic PVC conduit medium grade (MMS ISI) of size not less than 20 mm dia(or as site requirement) concealed in wall/over ceiling,modular metal flush boxes of required size and with modular plates incl of all accessories and all as specified including 1.5 sqmm FRLSH PVC insulated sheathed multistranded copper earth conductor to common earth and connected to earth dolly for light / fan/ bell point controlled by one switch. Note:- (i) Cost of PVC conduit, modular plates,frames, cover plates etc; are deemed to be included in the quoted rate. (ii) M&L for cutting chases on walls / ceiling and making good disturbed surfaces including finishing with cement mortar (1:3) etc; are deemed to be included in the quoted rate.

All as per item 151 above but for 3 pin 5 Amps switch socket combination on independent board with 1.5 sq mm copper cable complete all as specified and directed.

All as per item 151 above but for 3 pin 16 Amps switch socket combination on independent board with 2.5 sq mm copper cable complete all as specified and directed.

All as per item 151 above but for 5 Amps socket point on the same board controlled by one switch complete all as specified and directed.

S & F in replacement of modular switch 10A,1 module single pole, one way complete all as specified and directed.

Supply and fixing in replacement socket out let, 5 pin 10 Amps flush type complete all as specified and directed.

S & F in replacement of modular switch 16A,1 module single pole, one way complete all as specified and directed.

S & F in replacement of modular socket outlet 5 pin ,16 Amps,2 module, 240 Volts complete all as specified and directed.

S & F in replacement of switch bell push flush type 5 Amps complete all as specified and directed.

S & F in replacement of ceiling rose polycarbonate type three terminals complete all as specified and directed.

S & F in replacement of modular step type electronic fan regulator ,two module 120 watt single pole 240 Volts complete all as specified

S&F in replacement LED Tube light luminaires, 20-22 watts, lumen output not lessthan 2000 (4 feet), made of anodised extruded aluminium housng, with high transmissivity diffuser, high lumen output, with suitable integrated electronic driver, and operated in single phase, 230 volts, 50HZ, all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable of from connector and ceiling rose, complete all as specified and directed. Make :- Philips model SmartBright or equivalent in Wipro / Crompton

M&L for 12W LED mirror light fitting warm fancy type of make Philips model No 31402 Bronze finish or of equivalent make as complete all as specified and directed.

M&L for LED 6W wall Decorative light fitting of make Philips 581915 Poise 6W Ip44 Led Wall Light or of equivalent make as specified complete.

Supply and draw submain wiring with two single core 6 sq mm FRLSH PVC insulated copper cable 1100 volts grade multi stranded, sheathed conductor in concealed PVC conduit including 6 sq mm multi-strand FRLSH PVC insulated copper wire for earth continuity conductor connected to common earth dolly complete and making good disturbed surface complete. Note:- Cost of PVC conduit, cutting chases on walls and making good disturbed wall surfaces including finishing with cement mortar (1:4) matching with the existing shade / tint are deemed to be included in the rates quoted.

S & F in replacement new generation energy saving and environmental friendly long life 35/40W LED wall street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having top Opening seperate driver compartment with IP66 protection and impact resistance of IK07 including necessary brackets (made out of suitable bore GI pipe light grade appx 0.6 meter long bend to shape) nuts, bolts, etc fixed on walls with MS clamp complete all as specified and directed. Make:- Philips of Model -SmartBright Street or equivalent in Wipro / Crompton.

S & F in replacement LED recess mounted (2'x2' size flat panel) luminaire which provide soft light and glare free symmertical illumination suitable for armstrong/grid ceiling of 36Watt,(Lumen output not lessthan 3600) complete all as specified and directed. M Make Havells(Cat No:- LHEBAEP5IW1W036) or of equivalent make as approved by GE complete all as specified and directed.

Supply & Lay underground XLPE insulated armoured LT UG electric cable with aluminium conductor 1100V grade in trenches fixed on wall (or) passing through pipes/in floors connecting up testing and commissioning of of size 16 sqmm 4 core complete all as specified and directed by Engr-in Charge. (Note : Including nacessary excavation and clamp on wall with proper screw complete)

Supply and fixing single pole and neutral enclouser with a two pin and earth plug and socket complete with one pole MCB 20 Amps complete all as spd and directed.

S & F sheet metal enclosure double door for MCCB DBs VTPN 6 way 415 V suitable for 63-100 Amp MCCB as incomer of make Legrand model-5077 41 or of equivalent make as approved by GE complete all as specified and as directed.

S&F MCCBs 415V ,16KA, 4 Pole 100 Amp all complete as specified and directed.

S & F sheet metal enclosure double door for MCB DBs SPN 12 way 240 V, complete flush mounted all as specified and as directed.

S & F MCB single pole (SP) 5 to 40 Amps, 240 volts , C curve , AC , 50 Hz ,10 kA complete all as specified and directed.

S & F MCB Single pole & neutral (SPN) 32-40 Amps, 240 volts , C Curve, AC , 10 kA complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Metre below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 15 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as shown on electrical plate No. 3 of SSR part - I , including taking out old U/s complete alll as specified and directed .

Anil Kumar Sarmah (BID ID -3201745)

M/s R S ENTERPRISE (BID ID -3202163)

M/S UDIPTA KUMAR BORAH (BID ID -3200726)

Chinmay Traders (BID ID -3201840)

M/S JIWA SINGH S GILL (BID ID -3201719)

M/S SHYAMAL SARMAH (BID ID -3202157)

shyam constructions (BID ID -3201930)