Mechanical and electrical works to be carried out at Lift Irrigation Scheme Lugripora Tujjar under Programme PRI (Panchayati Raj Institution).

Amount

Providing, laying, fitting, testing and commissioning of 200mm NB, MS pipe, 6.3mm thick plain ended type, anticorrosive, electric resistant welded for supply of Raw water from Lift Irrigation Scheme Lugripora Tujjar with following specifications 1. Nominal bore: - 200mm 2. Wall thickness: - 6.3mm 3. Length of each pipe: -6m 4. Manufacturing of pipe: - Certified IS/Bis-3589 5. Type of welding: - ERW 6. Grade: - Fe410 7. Working Pressure: - 5mpa 8. Features: - High strength, corrosion resistant and high deformability. 9. Finish: - Black, rust preventive coating/Bitumin coating 10. Package: - Plastic caps on Bevelled ends. The pipe to be laid underground after excavating proper trench required for 200mm NB pipe as per site requirement/direction of I/c Engineer. The pipe to be connected end to end by required flanges 10No.s of dia. 200mm not less than 20mm thick fitted by mechanical operations, viz, cutting, welding aligning properly. The welding to be carried out by mobile welding set, which includes DG set, welding set, good quality electrodes of Make Adore/Advani, and by skilled workers. All tools and tackles for laying, lifting, connecting end to end and testing of pipe should be arranged by the firm. The pipe to be tested for required hydrostatic pressure. Back filling of trench after laying and testing of pipe by available excavated earth. Includes manual consuldation by hand rammer and disposal of excavated surplus earth as per direction of I/c Engineer.

Providing, Fabrication and erection of overhead gantry (HOT) for suction system at LIS Lugripora fabricated out of 150mm NB-MS pipe of 6.3mm thick by required mechanical operations. The two No’s of vertical posts of size 6m each fabricated out of 150mm pipe be erected and embedded in cement concrete blocks in M15 mix after excavating proper trenchs by manual means of size-2′ 6 ″ ⅹ 2 ′ 6 ″ ⅹ 3 ′ .The Base plates of size 300mm ⅹ 300mm ⅹ12mm be fixed on both ends of the vertical posts by proper welding. The horizontal beam shall be fabricated out of ISMB-150 of length not less than 5m fixed completely on the top ends of the aligned vertical erected posts by required welding/ nut bolts as per direction of I/c Engineer. The Job includes applying of metallic primer and two coats of metallic anti corrosive paint on the whole gantry.

Providing /Installation/Testing and Commissioning of Chain Pulley Block of capacity 2 MT with min lift not less than 6m rubost type. Make-Globe/Pull lift/ Indef./as approved by S.E Mech. (spear gear type) Heavy duty.

Providing, fabrication, installation, testing and Commissioning of suction system for horizontal pumping unit at LIS Lugripora. The suction system to be fabricated out of 200mm NB M.S pipe of 6.3mm thick as per required pipe pieces both horizontal and vertical fabricated by means of required mechanical operations viz, cutting, welding, fitting, connecting end to end aligning as per site requirement. The welding to be carried out by superior quality electrodes and skilled workers. The required pipe pieces should be of size as per detail 3000mm ⅹ 01 No, 600mm ⅹ 02 No., 450mm ⅹ 02 No., 1000mm ⅹ 01 No. Also each pipe piece should be flanged both ends with required dia flanges of thickness not less than 20mm. The job also includes providing and fabrication of reducers/ increasers as per required pump suction/delivery complete in all respects. The job also includes Providing, fabrication and fitting of 200mm NB long Radius bends 01 No flanged both ends with 20mm thick flanges. The suction system includes Providing and fitting of nut bolts, EPDM gaskets, leak proof solution etc complete in all respects. The job also includes providing and applying of metallic primer two coats and two coats of anti-corrosive metallic paint to whole suction system.

Providing, Installation, Testing and Commissioning of foot valve of 200mm dia. Mild Steel heavy duty complete in all respects with nut bolts, EPDM gasket/leather washer. Fabricated out of 6.3mm thick pipe and bell mouth 350mm dia. and overall height 350mm with strainer etc.

Providing, Installation, Testing and commissioning of non-return valve 200 mm dia. with hydrostatic pressure bearing capacity of PN 1.6. of make Kirloskar /sigmaflow /AVK/Vag. The job also includes providing and fitting of 2 No.s of MS flanges 20 mm thick with nut bolts and gaskets complete.

Providing, Fabrication of steel structure mobile canopy of size 6′× 4′ fabricated out of ISA- 40×40×6 m and CGI sheets for housing` Of horizontal Pumping unit. The job includes providing and fitting of nut bolts and boring/drilling and reaming of angle iron for fixing of canopy. The details are as: Vt Posts: - 4 No. × 6′ = 24 rft Hz posts long Upper and lower: - 4 No. × 6′ = 24 rft Short Hz pieces: - 4 No. × 4′ = 16 rft Rafters: - 8 No. × 3′= 24 rft King Posts: - 4 No.×1 ′3′′ =5 rft Total: - 93 rft = 99.23 kg Base plates= 4 No. × 0.5 *0.5*6 mm CGI sheets: 2No. *3’*6’ =36rft The job also includes providing and applying of primer coat and two coats of enamel paint to whole canopy. Also includes providing and laying of cement concrete blocks of size 1’6”* 1’6”* 1’6” *4 No. in M15 mix with 16 No.s of L/J type bolts.

Providing/installation/testing and commissioning of horizontal mono block pumping unit single phase for priming system with all fittings complete. The details here are: Type: Mono block single phase Discharge: 0.5 to 1 lps Head: Range 7 to 10 m Speed: 2900rpm Quality of water: Raw Motor rating: corresponding to head and discharge. Make: Usha/Crompton, equivalent. The job includes providing and fitting of 20mm GI pipe 25 mtrs along with all pipe fittings, pipe specials viz., elbows, unions, tees, etc. for fabricating priming system to horizontal motors. The job also includes ball valves of size- 20mm dia of heavy duty 4 No. for the same. The priming system shall be fabricated as per site requirement

Providing and fabrication of steel structure bed of size 3′×6′ fabricated out of ISA 40×40×6 m. The job includes providing and fixing of ply board of 19mm thick of size 3′×6′ to steel structure bed. The job also includes applying of primer coat and synthetic enamel paint to ply board and steel structure bed.

Providing of solar lantern dual charger with solar plate and adapter for lighting purpose. Make: Indus/Tata/Green.

Providing of tool kit/set housed in a steel box. i. Hammer 1 kg- 1 No. ii. Plier insulated with a thick sleeve. 2No. iii. Double ended ring spanners (chrome plated) of size 20/22, 24/26,25/26,21/23 and 30/32. iv. Double ended D. spanners chrome plated of size 20/22, 24/26,25/26,21/23 and 30/32. v. Long screw driver insulated. 2 No. vi. Electric multimeter analoque type. 2 No. vii. Digital clamp tester capable of measure upto 500 Amp. 01No. viii. Pipe wrech of size 600mm and 450mm. 1 No. each. The above too set shall be of Taparia make completely and with tool box.

Providing of steel table of size 4′×2′ fabricated out of 1.5mm black steel plate and ISA 35 ×35* 5 of required size as directed by I/c Engineer includes applying of primer coat and two coats of paint

Providing and fitting of 35 sqmm copper cable multi stranded PVC insulated from out-put of HT transformer to change over/MCCB. The cable to be laid through PVC conduits overhead as per requirement. The job includes crimmping and termination of ends.Make: National/Imperial/Havells.

Illumination of pump house by way of providing and fitting of five No. of lighting points, Two No. of heating points, four No.s of lighting points inside the pump house and One No. outside the pumping station by way of providing and fitting of switch socket, angle holders, switches, distribution wire of 1.5 sqmm copper multi stranded laid through PVC channels fixed on walls by way of required nails, rawal plugs and other required accessories. The Two No.s of heating points comprises S-S combine 3-way 2 Nos 16 A distribution wire 4 sqmm copper multi stranded distributed through PVC channels neatly and smoothly. The job also includes providing and fitting of 300mm 3 blade wall mounted fan. Make Usha/Havells/Orient/equivalent. 1 No. and one No. exhaust fan of 9 inch dia. Make Havells/Usha/equivalent.

Providing, installation, testing and commissioning of Star Delta Starter Handle type, manually operated 60 Hp with relay mechanism and copper contactor points of suitable rating. Make Bentex/Kilbern/equivalent. (double contract heavy duty).

MEER ENGINEERS INDUSTRIAL ESTATE SOPORE

M/S EURO LIGHT ENTERPRISES