PROVN OF 01 X GD ROOM WITH ATT TOILET AND BATHROOM UNDER GE DEHRADUN

Amount

Surface excavation in any type of soil (not exceeding) 30 cm deep and averaging 15cm deep and getting out complete all as specified and as directed.

Excavation in trenches, n exc 1.5 mtr wide and n exc 1.5 mtr in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. n exc 10 Sqm on plan and n exc 1.5 mtr in depth and getting out in any type of soil complete all as specified and as directed by Engr-in-Charge.

M&L for Anti termite treatment treating the backfill in contact with foundation at the rate of 7.5 ltrs of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfillto be measured) complete all as specified and as directed.

M&L for treating the bottom and sides of excavation at the rate of 5 ltrs of emulsion pe square meter of surface area all as specified and directed.

M&L for Anti termite treatment treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed.

M&L for Anti termite treatment Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and as directed.

M&L PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) for fdn/ mass concrete complete all as specified and as directed by Engr-in-Charge.

M&L for RCC M-25 Design mix (using 20 mm graded aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified.

M&L for RCC M-25 Design mix (using 20 mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified.

M&L RCC M-25 Design mix (using 20 mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L RCC M-25 Design mix (using 20 mm graded aggregate) in Columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for Providing precast RCC M-25 Design mix (using 20 mm graded aggregate) set in cement mortar 1:4 in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified.

M&F Formwork flat fair finished to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified.

M&L Formwork flat fair finished surfaces to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed.

M&L Formwork square, rectangular or plougonal fair finished surfaces to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified.

M&L for Formwork to flat fair finished to soffits of suspended slabs such as roof slabs, floor slabs, landings , shelf and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L for Formwork rough finished surfaces to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontalor sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M&L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in 1:6 complete all as specified and as directed .

M&L for rendering 15 mm thick on other then of brick work or concrete surfaces in cement mortar 1:6 finished surfaces even and smooth without extra cement complete all as specified and as directed by Engr-in-Charge.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished surfaces even and smooth without extra cement with WPC complete all as specified and as directed by Engr-in-Charge.(WPC paid seperately)

M & L rendering 10mm thick in cement mortar 1:3 on fair faces of concrete work even and smooth as in ceiling complete all as specified and ditected.

Supply only water proofing compound

S & F mild steel TMT bar 10 mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

S & F mild steel TMT bar 6 to 8 mm dia as in stirrups cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for new plastered surface of walls including corners and applying two coats of distemper oil emulsion over applying of 1-2mm thick wall care putty finish wall surface even & smooth by roller complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying three coats of white wash on ceiling, off sets, pillar etc all as directed and specified.

M&L for preparation of new untreated steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

S&F in repair framed work such as grills,gratings,etc., with ends of bars shoulderedor riveted, or forged into spikes; framed guard bars;barred iron doors and similar work conforming to Fe 210,Gde E-165 complete all as specified and as directed by the Engineer-in-Charge.

Hardcore of gauge n exc. 63 mm, except material retreived from item 1 deposited, spread and levelled in layers n exc.15 cm thick, watered and rammed to a true surface complete as specified.

M&L for 75mm thick PCC 1:3:6 type C-2 using 20 mm graded stone agg as in sub base for laying floor finishes complete all as specified and as directed.

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile of size 600mm x 600 mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar of 1:6 complete all as specified and directed.

All as per itme No 33 here in above but as in skirting and including 10 mm thick rendering in cement mortar 1:4, complete all as directed and specified.

M & L for coloured glazed ceramic tiles in vertical surfaces 300x450x7mm thick over and Rendering 10mm thick on fair faces of brick work or concrete surface in CM 1:6, set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tiles of size 400mmx400mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar of 1:6 complete all as specified and directed.

Supply and fixing of stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature and fixed with stainless steel wire staples complete all as specified.

S&F factory made 100 % solid wood plastic composite (WPC) door frame 125x50 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof, termite proof, fire retardant and having good screw holding capacity all as per specification and drawing complete all as specified and directed by Engr-in-Charge.

Supply and fix factory made 100 % solid wood plastic composite (WPC) door frame 105x60 mm made from wood plastic composite (single extruded process) material with density 780 Killogram/Cubic meter from ISO certified company door should be water proof, termte proof, fire retardant and having good screw holding capacity all as per specification and drawing complete all as specified and directed by Engr-in-Charge.

S&F factory made 100 % solid wood plastic composite (WPC) door frame 75x50 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof, termite proof, fire retardant and having good screw holding capacity all as per specification and drawing complete all as specified and directed by Engr-in-Charge.

S&F 30 mm thick factory made solid WPC (Wood plastic composite) gauged skeleton door shutter (single door piece to be used) with SS wire mesh in any number of division with brown wood grain texture, including stainless steel wire shall mesh be fixed with 15x15 Square tube in side rails with screwing 8x28 heat metal zink coated screws can density shall be as per manufacturer specified and complete all as specified and directed by Engr-in-Charge.

S&F factory made single extruded WPC (Wood Polymer Composite) solid both side prelaminated decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F 200 mm long, solid in one piece stainless steel barrel tower bolts complete all as specified and directed by Engr-in-charge.

S&F 150mm size solid in one piece stainless steel handles,cast D type, fixed in stainless steel screwsall as directed complete all as specified and directed by Engr-in-Charge.

Supply & fix for powder coated Aluminium standard hollow section as mentioned below window frame (Bombay sliding) with two glazed shutter and one nos stainless steel wire gauged shutter sliding type, 3 track numbers for sliding windows, and glazed with glass 4mm thick & including glazing clips, rubber beading / gasket anodised beading, screw and lock type handle of size 75mm, 2 Nos aluminum including locking system and provision of space for AC etc complete all as specified and directed by Engr-in-charge. Size of Track-Both Top & Bottom (Verticles sides):- 100 x 44 x 1 mm Size of Shutter Frame:- 25 x 12 x 1 mm Note: Iron grill with frame to be fixed with window (measured and paid separately)

S&F 100 mm size stainless steel butt hinges and fixed with stainless steel screws, complete all as specified and directed by Engr-in-Charge.

S&F stainless steel sliding door bolts 204 grade, hasp and staple type with bright bolt not less than 12mm dia with and incl a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 250mm long complete all as specified and ditected.

S&F floor door stopper of stainless steel double legged and tongue, 304 grade, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified and ditected.

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S & F jointing and testing galvanised steel water tubing 15 mm dia bore medium grade with all fittings such as bends, tees, nipples, elbows, socket reducers, etc, fixed to walls and ceilings or laid in floors complete all as specified and directed.

S & F jointing and testing galvanised steel water tubing 20 mm dia bore medium grade with all fittings such as bends, tees, nipples, elbows, socket reducers, etc, fixed to walls and ceilings or laid in floors complete all as specified and directed.

M & L cutting chases for concealed water tubing or concealed conduit wiring, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges, etc., cutting not exc 10 cm width or girth complete all as specified & directed.

S & F , vitreous china wash down water closet pedestal pattern white (excluding flushing cistern and flush pipe) with CI ‘P’ or ‘S’ trap including plastic white sheet cover, CP jet spray with 1.0 metre long PVC pipe, connecting to stack pipe and to flushing pipe and complete including making good to floor complete.

S & F 10 litres capacity PVC low level valve less symphonic action type flushing cistern white with inlet, float valve, float and handle including brackets with 32 mm dia PVC pipe 600 mm long complete all as specified and as directed by Engr-in-Charge.

Supply and fix for rotational moulded polyethylene 1000 Ltrs Capacity water storage tanks of weight not less than 33 Killogram (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball brass valve, with polythelene float three layer external and internal white and fly nut complete screwed down for iron pipe of 20 mm dia complete all as specified and directed.

S&F 20 mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified.

S & F vitreous china wash basin, white, flat back, size 550x400 mm including 32mm waste couplings, brackets and cutting for and pinning in ends of brackets complete all as specified and directed.

S & F 15 mm pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-in-charge.

S & F 15mm fancy type, chromium plated stop valves, angle cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S & F 15 mm bore bib taps, chromium plated cast copper alloy long body, screwed down, screwed for iron pipe or for brass ferrule complete

S & F Chromium Plated brass soap dish fixed to wall with chromium plated brass screwed and cup washer complete all as specified and directed.

S & F brass chromium plated towel rail, 20 mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

M & L PVC (SWR) (Class-II) floor trap plain with grating including jointing with solvent cement 75 mm bore outlet complete

S & F PVC (SWR) (Class-II) soil waste & vent pipe in any length without ears laid in floors, trenches or fixed to wall complete for 75 mm dia bore of pipe complete

S & F PVC (SWR) (Class-II) soil waste & vent pipe in any length without ears laid in floors, trenches or fixed to wall complete for 110 mm dia bore of pipe complete

S & F PVC (SWR) (Class-II) bends, T, reducer any radius with rubber ring joints, fixed to wall / floor / in trenches complete all as specified and directed for 75 mm dia pipe.

S & F PVC (SWR)(Class-II) bends, T, reducer any radius with rubber ring joints, fixed to wall / floor / in trenches complete all as specified and directed for 110 mm dia pipe.

S & F PVC (SWR) (Class-II) junction single, (Single T), any radius with rubber ring joints, fixed to wall / floor / in trenches complete all as specified and directed for 110 mm dia pipe.

S & F PVC (SWR)(Class-II) juctipon double , (double T) equal and unequal of any radius with rubber ring joints, fixed to wall / floor / in trenches complete all as specified and directed for 110 mm dia pipe.

S & F 75 mm dia PVC (SWR) (Class-II) vent cowl complete.

Supply & Fix PVC connection 15 mm dia 450 mm long with brass fly nut at both ends complete all as specified

M & L PVC (SWR) (Class-II) GULLY trap 125/110 mm, setting And jointeing with solvent with solvent cement as per specified and directed

M&L PVC Nahani Trap of 75 mm dia , with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F brass chromium plated shower rose 125 mm size complete all as specified and directed by Engr-in-charge.

S&F 25 mm dia stainless steel polished 204 grade drapery rod 1mm thick with final decorative, including brackets, decorative finished at both ends complete all as speccified and directed as per approved sample complete all as specified and ditected.

M&L 75mm thick PCC 1:3:6 type C-2 ( 40 mm graded aggregate) as in plinth protection finished even and fair complete all as specified.

M&L Forming Construction joint 30mm deep x 10mm wide of grade A filled with sealing compound complete all as specified and directed by Engr-in-charge.

Supply & fix 18 mm thick PVC board one side prelaminated and other side plain white colour as in cup board shutters and frames, kitchen cabinet front shutter, partion, shelf, & drawer, fixed with screws, solvent cement / adhesive ,complete all as specified and directed by the Engineer-in-Charge.

Supply & fix 18 mm thick PVC board both side plain white colour as in cup board shutters and frames, kitchen cabinet front shutter, partion, shelf, & drawer, fixed with screws, solvent cement / adhesive ,complete all as specified and directed by the Engineer-in-Charge.

S & F Continuous (piano) hinges of 30 mm width of flap, mild steel, bright finish or electrogalvanised complete all as specified as directed.

S&F magnet catcher for cub board with brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F Hasp and staple of 100 mm , mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screw complete all as specified and directed.

S&F glass corner shelf suitable size made of 5mm thick toughned glass all as specified.

Returning filling in including spreading levelling watering and well ramming in layers not exc 25 Cm complete all as specified and as directed.

Removing excavated material exc 1.5 km n.exc 5 KM and depositing where directed at a level n exc 1.5 mtr above the starting point complete all as specified and as directed by Engr-in-Charge.

Material & labour for surface preparation of roof and treating of joints, filling of honey combs and providing 25 mm thick PCC (1:2:4) type B-0 with WPC over roof surface complete all as specified and directed.

M&L for Water proofing roof treatment with Polymeric water proofing membranes of weight not less than 3Kg/sqm five layers with center core as 90 micron high molesuvre,high density polythene film sand witched between two layers of polymeric (Static polythene based) between laminated on both sides with 20 micron HMDPF film over a coat of hot blown bitumen with 85/25 grade @ 1.20 Kg/Sqm after priming the surface with bituminous emulsion @ 0.40 Litre/Sqm on plastered surface. Water proofing membrane should be laid with over laps 150 mm at ends and 75 mm for sides and shall be bounded uniformity by LPG torch flame over the polymeric water proofing membranes apply semi hot blown bitumen 85/25 grade @ 1.20 Kg/ sqm and applying aluminium reflective paint over it as per manufacturers instructions complete all as specified and directed.

Provision of Septic Tank for 25 users all as shown in Drg No TD - 217 complete all as spcified and directed

Provn of soakage wells of size 1.2 mm dia X 3.0 M deep all as shown in Drg No TD-309 complete all as specified and directed

Excavation in trenches n exc 1.5m wide and n exc 1.50m in depth for foundation etc and getting out in soft/loose soil complete all as specified and directed by Engineer-In- Charge.

M&L for mild steel TMT bars 10 mm dia and over cut to length and bent to shape required and binding with mild steel wire dia not less than 0.9 mm (annealed) complete all as specified complete all as specified and directed by Engineer-In- Charge

M&L for providing precast cement concrete coping with plain fair faces incl chamferes, weathering, throating etc type B0, 1:2:4 using 12.5mm graded stone aggregate and set in CM 1:4 complete all as specified and directed by Engineer-In- Charge.

Removing excavated material not exceeding 50M and depositing where directed at a lavel not exceeding 1.5m above the starting point, soil complete all as specified and directed by Engineer-In- Charge.

M & L for precast RCC (1:1.5:3) type A-1 using 20 mm graded stone aggregate) as in cover slab for for manholes etc set in cement mortar (1:4) including use and waste of form work complete all as specified and directed by Engineer-In- Charge

S&F MS Flats, joist channel (Fe 410-W Gde E-250 Quality A), fixed indepently or framed without connecting plates confirming to Grade Fe 410-0 or Fe-310-0 complete all as specified and directed by Engr-in-Charge

M&L for brick work with sub class 'B' bricks old size bricks strainght or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed by Engineer-In- Charge.

M & L for cement concrete 1:3:6 type C-2 for 150 mm dia in concrete bed to drain pipes including packing under and haunching against the sides of pipes etc complete all as specified and directed by Engineer-In- Charge

M & L for reinforced concrete pipes,150mm dia SGSW Pipe laid and jointed complete with collars complete all as specified and directed by Engineer-In- Charge.

M&L for point wiring with 1.5 Sqmm. (nominal area) FRLSH, single core PVC insulated 1100 Volts, grade multistranded copper conductor unsheathed in and including concealed PVC conduit medium duty 20 mm dia or higher and heavy grade conduit fittings and heavy duty accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.6mm thick for mounting of switches, sockets, fan regulator etc with suitable size 3.0mm thick hylum sheet cover, one green colour FRLSH cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge

One light point/ ceiling fan point/ Exhaust fan point controlled by one-one way switch.

One three pin 5 Amp socket on same board with other switches.

One three pin 5 Amp socket on independent board

All as per item No 100.03 above but one 3 pin socket outlet 15 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm.

S&F step type regulator socket type double module 5 step for ceiling fan 1200/1400 mm size 230 volts 6 Ampds 400 watts.

S&F switch piano flush, button type 5 Amp SP 250 V AC complete all as specified & directed.

S&F switch piano flush button type 15 Amps SP 250 V AC complete all as specified & directed.

S&F socket outlet two in one three pin 5 Amp and 15 Amp 2 module 120 W flush type complete al as specified.

S&F socket outlet multipurpose 3 Pin 5 Amp and 2 Pin 5 Amps 250 V AC complete all as specified & directed.

S&F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 220 V AC.

M&L lamp holder insulated body with back plate suitable for angle and batten fitting including LED bulb 9 watt complete all as specified.

S&F sheet metal enclosures 240 volt with 200 Amp rated bus bar for double door 8 way DB,s IP-43 IK 09 metal door suitable for one MCB SPN as incoming and 06 MCB SP as out going complete all as specified and directed

S&F MCB double pole 240 Volt 10 KA 40 Amp 'B' series conforming to ISI marked complete all as specified & directed

S&F MCB single pole and 240 volt 10 KA 5-32 Amp 'B' series conforming to ISI marked all as specified and directed

S&F wall mounted LED tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed.

All as above item no. 112 but capacity 9/10 watt

S&F air ventilation fan made of sturdy Engineering plastic complete with louvers shutter, 250 mm, 1200 RPM, single phase, 230V AC including necessary, M&L for making hole fixing arrangement on wall with frame holdfastner, bolt, washer etc including connection with twisted white three core flexible copper multistranded conductor cabl from ceiling rose to connector all a directed

S&F in replacement of Geyser vertical mount type 25 Ltrs capacity five star rated , shockproof and rust proof metal body compact size including two nos PVC connection heavy duty and connecting with all fixing arrangement of nuts & bolts and fixing on wall complete all as specified & directed .

Supply and Fixing Integral LED Bldg security Light Luminaire comprising of pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 45 watt with efficiency 100 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours, complete all as specified and directed.

Materials and Labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground end vertically to a depth not less than 2.25 meter deep below ground level with top edge of the earth plate at a depth not less than 1.5 M below normal ground level connected to galvanized steel earth wire 4 mm dia by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1, cover slab 54 cm x 54 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm c/c both ways, and with one handle for lifting made out of 10 mm dia MS round bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing (light grade) for protection of earth lead connection, including necessary excavation and earth work in any type of soil and necessary testing complete all as shown on electrical plate No 3 of SSR Part –I (2009) and as directed.

All as per item No 117 but in GI STRIP 32X6 MM

S&F Galvanised iron strip 32 x 6mm buried in ground

S&F air termination single pointed aluminium rod of 12mm dia 300mm long fixed on pipe 50 mm drilling nuts, bolts washers for resting/supporting of air terminals etc complete all as directed by Engineer-in-Charge.

Supply and laying galvanised steel tubing 50 mm bore light grade laid in trenches or fixed to poles/walls etc for cable protection complete all as specified and directed.

M&L for Excavation in trenches n. exc. 1.5 mtr wide and n. exc. 1.5 mtr in depth for laying of underground cable, foundation of pole and getting out in soft/loose soil complete all as specified and directed.

M&L for Returning, filling in excavated soil in trenches including spreading, levelling, watering and well ramming in layers n. exc. 25 cm thick complete all as specified and directed.

M&L for Removing of excavated soil to a distance n. exc. 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

M&L for laying local dry clean sand filling for cushioning in trenches around under ground cable complete all as specified and directed.

M&L for laying well burnt brick, old size in trenches, as protection of under ground cable complete all as specified and directed.

Supply, laying, jointing and testing of underground XLPE insulated, armouredheavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 Sqmm 2 Core laid in trenches/ducts/along poles/through pipe under road etc with new aluminium lugs of cable size all as specified and directed.

S& Fix ceiling fan 1200 mm sweep single phase 230 volts double ball bearing wioth down rod ,canopy ,blades etc BLDC TYPE ,5 star rated incl regulator & flexible wire upto ceiling rose

M.K Engineers (BID ID -3382104)

V S ENTERPRISES (BID ID -3385545)

IMPERIAL ENGINEERS (BID ID -3386297)

M/s Pradeep Kumar (BID ID -3385666)

M/s RP AGRAWAL (BID ID -3385643)