Equipments for Electronics Lab

Digital Storage Oscilloscope Bandwidth 100 MHz Number of Channels 2 Analog and 1 External Channel Vertical Sensitivity 2mV/div - 10V/div Vertical Resolution 8 Bits Real Time Sampling Rate 1GS/s (1 Channel) & 500 MS/s (Both Channels) Equivalent Sampling Rate 25GS/s Memory Depth 16K Points (1 Channel) & 8K Points (Both Channels) Triggering Points Edge, Pulse, Width, Slope, Video, Pattern, Continuous Time & Alternate Cursor Measurements Manual, Track & Auto Interface/Connectivity USB Device and Host, RS-232, P/F Out Maximum Input Voltage 1 MegaOhm || 15 PicoFarads, 300 Volts RMS, CATI Display 5.7 Inches (320x200) TFT QVGA with 64K Color LCD Backlit Display Digital Filters LPF, HPF, BPF & BRF

Regulated power supply, 0-64V variable, 3A * Input Voltage : 230V, ±10%,50Hz * Out put voltage: 0 to +64V Continuous variable * Output current: 3.0A * Metering : 3dpm * Regulation: CV ±0.01% +2mV Line Regulation CC ! CV ±0.1% +2mA Load Regulation CV CV ±0.01% +2mV Load Regulation CC !! CV ±0.1% +2mAL * Ripple voltage: Less than 1mV RMS Display: 2 digital meters for current and voltage, 7segment LED display*Meter Accuracy ±0.2% of reading ±2 least counts * Protection: Against short circuit and continuous overloads

UNIVERSAL IC TESTER - ( DICT-03 ) • Tests a wide range of Digital IC's such as 74 Series, 40/45 Series ICs •Can test Micro- processor 8085, 8086, Z80 & Peripherals like 8255, 8279, 8253, 8259, 8251, 8155, 6264, 62256, 8288, 8284 • Tests a wide range of Analog IC's such Op-amp, 555 Timers, Transistor Arrays, Analog switches, Opto- couplers, 12bit/8bit ADC & DAC, Comparators, Waveform generator, PWM IC, Sample Hold IC, Voltage Regulator, Frequency to Voltage converter, Latch driver, VCO Ic’s, PLL Ic’sCross Point Switch, Seven segment display of common cathode & common anode type. •Auto search facility for all Digital ICs • Test by: Truth table/sequence table comparison. • ZIF: Two numbers of 40 pin DIP ZIF sockets, Keys: 50 cherry keys Key pad with numerical & functional keys. • Display: 16 X 2 LCD Display.

Digital IC Trainer 10 Logic Input switches with LED Indication for logic low and logic high. 10 LED for output indication with LED Driver. Fixed Clock generation of 128 KHz, 64 KHz, 32 KHz, 16 KHz, 8 KHz, 4 KHz, 2 KHz, 1 KHz, 500 Hz. Logic Pulsar provides single pole double throw bounce less pulses of Low to High and High to Low transitions. Solder less Breadboard with 840 tie points. 1 No’s of Breadboard. Two seven-segment LED display with decoder driver and provision for BCD input Fixed DC Power Supply: +5V/500mA, -5V/500mA +12V/500mA, -12V/500mA. Input supply 230V + 10%, 50Hz AC voltage Trainer is housed in a strong cabinet. interconnections (Input/output) Cords

Dual power supply, +15V,-15V * Input Voltage : 230V, ±10%,50Hz * Out put voltage: +15V,-15V * Output current: 2.0A * Metering : 3dpm * Regulation: CV ±0.01% +2mV * Protection: Against short circuit and continuous overloads

EMBEDDED AVR TRAINER KIT ATMEGA32 8 bit with 32K program flash, 1xUART, 4x 8bit I/O, upto 16 MHz operation with ISP Programming Facility.  USB to UART converter with two status LEDs for  Programming communication interface.  On board 16 LEDs for Digital Logical Output.  Two 8 way DIP switch for Digital Logical Input.  Onboard 16X2 Alphanumerical LCD.  I2C Compatible. 4 Digit Seven Segment displays using PCF8574. # 24C512 EEPROM (64KB). # DS 1307 RTC with suitable battery. # 4 Channel 8bit ADC and one 8Bit DAC using PCF8591.  Temperature Sensor interface LM35.  I/O lines are terminated through a 26 pin FRC connector for external interface.  Onboard 12V relay with driver Circuit.  Onboard 4x4 Matrix keypad interface.  0.5 Kg Stepper Motor with relevant driver circuit.  DC Motor  On board supply ±12V, 5V.  Supply input voltage : 230V AC. Board mounted in a attractive plastic/metal cabinet.  USB Cable.  AVR studio ISP programmer software.

8051 MICROCONTROLLER TRAINER KIT [MICRO-51 LC (LCD)] * 8051 / 89C51 Microcontroller, 12MHz Clock speed * Program Memory RAM - 32KB * Data Memory RAM - 32KB * Program Memory EPROM - 32KB KEYBOARD AND DISPLAY * 16x2 LCD Display PARALLEL I/O BUS EXPANSION 8255 connections are terminated in one 26-pin FRC header (24 I/O lines) VXT-Bus (50 pin FRC connector) for interfacing VBMB series of experiment board and bus expansion 40-pin FRC header * On board 8-digital inputs 8-Way dip switch * On board 8-digit outputs * The port lines PI used as input (switch) or output LED SOFTWARE: * Built-in line assembler & Dissembler * Housed in a sleek plastic cabinet. SERIAL PORT: * On chip serial port 9 pin D Male connector * Input : 230V AC * Output: +5V/3A, +12V/0.5A * 1 No. of 3V lithium battery / 3.6V NICD Battery

PLC Trainer Kit Input Supply : 12/24V DC Timers & Counters : 256 Nos Each Digital Inputs : 8 Nos Digital Outputs : 4 Nos Program Memory : 400 Blocks 4 Inputs can be configured as Analog Input (0-10V) DC Optional SD cards for data logging Ethernet Communication Interface Networking with up to 8 units Demo Panel Specification 8 Nos of toggle switches & LEDs provided for Digital Inputs 6 Nos of LEDs provided for Digital outputs indication purpose I/Os are terminated into SP7 connectors for external trainer interfacing Patch chords provided for interfacing the external trainers Modules and all the components mounted on cabinet

3 MHz Function Generator Output Function Sine, Square, Triangle Frequency Range (For Sine, Square) 0.1Hz~3MHz Frequency Range(For Triangle) 0.1Hz~1MHz Frequency Resolution 0.1Hz Maximum Frequency Stability ± 20 ppm Frequency Accuracy ± 20 ppm Amplitude Range 20Vp-p (into 50Ωload) Impedance 50Ω±10?H Attenuator -40dB±1dB×1 DC Offset <-5V~>+5V(into 50Ωload) Duty Control Range 25% to 75% below 1MHz (Square wave only) Display 6-digit LED/ LCD display Rise or Fall Time ≦100ns at maximum output. (into 50Ωload) TTL OUTPUT Level ≧3Vpp

Xilinx Spartan 6 FPGA Study Board [VPTB – 16]  Xilinx Spartan 6 – XC6SLX4, TQ144Package Spartan 6 FPGA  3840 equivalent logic cells  75kB Max Distributed RAM  Twelve 18kB RAM blocks (216)  8 nos DSP48A1 slices  2 clock Management Tiles  Interfaces  On Board USB to JTAG  On Board Flash PROM XCF04S  Total 104 I/O pins : 86 I/O pins are used for integrating peripheral like LEDs, Switches etc., Balance 18 pins terminated in 20pin header for Add - on cards (3.3V compatible)  8 digital input using slide switches  8 digital outputs using Discrete Light Emitting Diodes (LEDs)  4 user push button switch  One RESET push button switch  Four nos of 7 segment display  One 16x2 LCD display  One five pin SPDT Relay  One Two pin small size 5V Buzzer  RTCC with external battery backup  One single channel 12 bit SPI high speed ADC with I/P range 0 to 3.3V  One single channel 12 bit SPI high speed DAC with O/P range 0 to 3.3V  Compatible with Xilinx ISE Design Suite Webpack edition DC MOtor , Stepper motor

SOLDERING STATION Rework Station 2 in 1 Hot Air Specs : Temp. range - 200 deg C - 480 deg C, 500W Integrated blower within hand held unit. Temperature Sensor for precise measuring,Digitally Controlled Built-in cut off sensor when placed on Cradle,Earthed 3 different air nozzle sizes Soldering Iron: Temp. range - 200 degC - 450 degC ,Needle Bit Iron Supply 24Volts / 50Watts,Earthed Rubber grip for non-slippery use.,MCH heater Warranty: 6 Months Warranty on controller

vasee electronics

Synergy Technical Systems

Amity Solutions

electrical world

Akshaya Associates

Analog and Digital Devices

MULTITECH SYSTEMS

Verdant Power Solutions LLP

V-Tech Instrumentation (India) Private Limited