ADDN/ALTN OF BLDG NO.T-81 INCLUDING FIRE ALARM/SMOKE DETECTOR AT 5 TAC AF UNDER GE (S) TEZPUR

Amount

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings.Complete all as specified and as directed.

Dismanting timber scantling 40 Sqcm and over in secion in any position in framed work or unframed work.Complete all as specified and as directed.

All as per Item No 02 above but In fillests, rails , posts, refters and purlins etc under 40 sqcm in section unframed work.Complete all as specified and as directed.

Dismanting wall /ceiling board (Fibre pulp insulation) or insulation boards any thickness including cover filters.Complete all as specified and as directed.

Dismanting timber boarding of any description fixed in any position.Complete all as specified and as directed.

Demolition of reed lathing, single or double including battens and plasters or checken wire lathing.Complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar.Complete all as specified and as directed.

Dismantling wrought iron or mild steel work or any description as in door, gates, etc and similar works complete all as directed

Taking down chowkats or frames exc 1.5sqm and not exc 4.0 sqm each with shutters ( without taking off shutters from the frame ) including dismantling of PCC bed blocks for hold fasts.Complete all as specified and as directed.

Taking down chowkhat with shutter/without taking off shutter from the frame n exe 1.50 each.Complete all as specified and as directed.

Taking down cement plaster, of any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water.Complete all as specified and as directed.

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness.Complete all as specified and as directed.

S&F 0.5mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of ISI Marked of any colour ,tensile strength of 550Mpa as in roof covering ,cladding to wall ,ridge,gutter etc fixed with self tapping screws complete all as specified and as directed .

All as per item No 13 2 above but plain sheet for ridge ,gutter/ Eaves board etc fixed with self tapping screws complete all as specified and as directed .

M&L 2nd class Hard Wood in scantling fixed clean swan in framed work.Complete all as specified and as directed.

M&L 2nd Class Hard Wood plain fillets square, rectangular or triangular in section clean sawn sectional area n exe 40 sqcm fixed with nails.Complete all as specified and as directed.

S&F Exposed GI powder coated snap grid frame for false ceiling 600x600mm size of wall angle 25x25x0.55mm size of cross tee and main tee 26x24x0.55mm and 32mm x 24mm x 0.55mm with 3mm dia single GI adjustable suspentor including supply and fixing of 4mm thick E Board decorative type in false ceiling including fixing arrangement from steel tress any type of tress.Complete all as specified and as directed.

S&F 6-10 mm thick PVC hollow panels with to 1.00 mm tkick wall thickness plain PVC sheet suitably placed in Wall/ ceiling inclding same and matching colour wall angle , u clip, end elip and jointer as in ceiling and walls including GI 0.50mm thick GI "C" channel @ 600 to 800mm c/c horizontally/ vertically and at every corner As per specification and drawing all as specified and directed

S&F MS framed works such as grills grating etc with ends of bars shouldered and for rivetted in forged into spikes, framed guard bars, railing and similar work confiring to Fe-410-0 or Fe 310-0 complete all as specified and directed

S&F Anodised aluminium frame powder coated 50 microns for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Anodised aluminium powder coated 50 microns window and ventilator shutters, sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc.complete all as specified

S&F Anodised aluminium powder coated 50 microns door shutter aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 02 Nos in each door , hinges ,anodised aluminium snap beading, screws etc.complete all as specified

S&F 35 mm thick 2nd class hard wood factory made flush shutter solid core construction with block board core and plywood face panels commercial type of both side.Complete all as specified and as directed.

S&F 35 mm thick 2nd class hard wood Glazed and skelton shutter open rebated and prepared to receive glass, gauze etc (without sash bars) edges of the framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members as specified in SSR Pt I clasue 8.24 (a).Complete all as specified and as directed.

S&F MS 300mm ordinary rat tail rod pattern spring including roller and roller plate.Complete all as specified and as directed.

S & F in repairs Aluminium (extruded section body type )door closer hydraulically regulated designation No 3, universal type , suitable for door shutter of 851 to 1000 mm in width and of weight and weight betwwen 61 to 80 kg ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed

S & F in repairs floor door stopper aluminium alloy body overall length 140 mm and tonge , anodised with hard drwansteel spring all as specified and directed

S & F In repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty all as specififed and directed

S&F 150mm long aluminium handle, cast type, anodised.Complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolts of extruded section 200 mm long and fixed with screws.Complete all as specified and as directed.

S&F 100mm Butt hinges medium weight cold rolled mild steel .Complete all as specified and as directed.

S&F Aluminium anodised sliding door bolts of size 300mm long, with hasp & staple ( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extreded sections or cast aluminium alloy.Complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing rubbish off the complete all as specified and directed.

M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) light shade, polished, area of each tiles exc 0.38 sqm but not exceeding 0.72 sqm, in floors etc. set and jointed in neat cement slurry and pointed in epoxy filler to match the shade over 15mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per item No 34 above but in skirting over 10mm thick screeding in cement mortar 1:3.

S&F Coloured Glazed ceramic tiles 450 x 350 mm x 6 to 7mm thick, in skirting /dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm screeding in Cement mortar 1:4.Complete all as specified and as directed.

M&L non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 Sqm but not exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4.Complete all as specified and as directed.

Supply and fix, as in repair, vitreous china wash down water closet pan (Pedestal pattern) white (excluding flushing cistern and flush pipe) including seat cover white closed type complete all as specified and directed

Supply and fix, as in repair, vitreous china wash basin, white, flat back size 580 x 450 mm, excluding taps, waste chain, plug and porcelain stopper but including brackets, cutting for and pinning in ends of bracket or erecting stand complete all as specified and directed.

Supply and fix, as in repair, 10 ltrs capacity PVC valve less syphonic action type, low level flushing cistern, white, with inlet, ball valve float and handle including brackets complete all as specified and directed.

Taking up or down 15 mm bore old steel tubing and connections, including disconnection of fittings from tubing including cleaning for re-fixing or removal from site complete all as specified and directed.

Taking up or down 20 mm bore old steel tubing and connections, including disconnection of fittings from tubing including cleaning for re-fixing or removal from site complete all as specified and directed.

S&F of 15 mm bore tubes medium grade galvanised with and incl all GI fitting (such as bends, elbows, Tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor complete all as specified and directed

S&F of 20 mm bore tubes medium grade galvanised with and incl all GI fitting (such as bends, elbows, Tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor complete all as specified and directed

Supply and fix,as in repair,15 mm bore pillar tap, fancy type cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without letter Hot or Cold with long screwed shanuls and fly nuts, screwed for iron pipe or for brass ferrule all as specified and directed.

Supply and fix,as in repair, 15 mm bore bib taps, cast copper alloy,cromium plated, fancy type, with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and directed.

S&F in repairs 15mm dia stop valve fancy type chromium plated with long shank and cup (conealed rype) screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

Dismantling and breaking up PVC drain pipes of 110mm dia or below jointed in CM and taking out of trenches.Complete all as specified and as directed.

Supply and fix, 110mm bore PVC (SWR)pipe single socketed with rubber ring joints fixed to walls all as specified and directed.

Supply and fix, 75 mm bore PVC (SWR)pipe single socketed with rubber ring joints fixed to walls all as specified and directed.

Supply and fix,as in repair, 32/40 mm dia PTMT 610 mm long waste pipe suitable for WHB/Sink complete all as specified and directed.

Supply and fix, CP 32/40mm dia waste coupling for stainless steel sink with inlet and out let screwed for pipe or connections etc complete all as specified and directed.

Supply and fix, as in repair, sinks with drainage board made out of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortor to dwarf wall or including fixing cantiriver lever brackets and connecting union to pipe overall size 915mmX460mm and bowl size 410mmX330mmX160mm all as specified and directed.

M&L 20mm thick Granite stone (of any type) work (table rubbed and polished) in cooking platforms and like fixed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match over with shade of granite complete all as specified and as directed.

M&L 20mm thick Granite (of any type) work (table rubbed and polished) for in skirting/border with 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shed of granite complete all as specified and as directed.

S&F for PVC (SWR) with access door bends 110mm dia.Complete all as specified and as directed.

S&F for PVC (SWR) with access door bends 75 mm dia.Complete all as specified and as directed.

S&F in repairs 75mm PVC (SWR) floor trap, including jointing with solvent cement.Complete all as specified and as directed.

S&F chromium plated Corner glass shelf with bracket complete all as specified and directed.

S & F in repairs Health faucet/ Hand shower (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S & F in repairs Toilet paper (CP) holder of brass chromium plated fixed to walls with chromium plated(CP) brass screws.Complete all as specified and as directed.

S&F in repair tubular Towel rail chromium plated 600mm long 20 mm dia D type complete all as specified and as directed.

Hacking out old broken glass any thickness, size, quality or description from wooden / metal frame works, glazed with putty or fixed with beads.Complete all as specified and as directed.

S& F in repair 3.0 mm thick sheet glass ordinary quality and glazing with oil putty in squares exc 0.5 sq. m in each pane in squares.Complete all as specified and as directed.

S& F 4.0 mm thick sheet glass ordinary/tinted quality and glazing with oil putty in squares exc 0.5 sq. m in each pane in squares.Complete all as specified and as directed.

S& F 4 mm thick sheet glass ordinary/tinted quality and glazing with oil putty in squares n exc 0.5 sq. m in each pane in squares.

S&F Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.Complete all as specified and as directed.

M & L for brickwork with sub-class 'B' bricks straight or curved on plan exc. 6m mean radius in half brick work built in cement mortar (1:4) complete all as specified and as directed.

M & L brick work (old size) with sub class 'B' bricks in CM (1:6) , straight or curved on plan exc 6 mtr nean radius, using old size bricks complete all as specified and as directed.

M & L, 15mm thick rendering in C.M. (1:4) on fair faces of brick work finished even and smooth without using extra cement.Complete all as specified and as directed.

M & L, 10mm thick rendering in C.M. (1:6) on brick work finished even and smooth without using extra cement.Complete all as specified and as directed.

M&L Applying two coats of acrylic emulsion distember to newly plastered/previously untreated wall over a coat of 1 mm thick layer of wall care putty over a coat of wall primer including preparation of newly platsered surface of wall by smart painting method all as specefied and directed.

M&L Applying two coats of acrylic emulsion distember by smart painting method to old surfce wall over a coat of 1 mm thick layer of wall care putty over a coat of wall primer including complete removal of existing treatment all as specefied and directed..

M&L complete removal of existing treatment and appplying two coats of acrylic exterior weather coat over a coat of damp proof primer and a coat of 1 mm thick wall care putty by smart painting method to make surface smooth to old plastered walls as per manufacturer instrcution and apllied by approved applicator complete all as specified and directed.

M&L preparation of newely plaseter sufaces and appplying two coats of acrylic exterior weather coat over a coat of damp proof primer and a coat of 1 mm thick wall care putty by smart painting method to make surface smooth to newely plastered walls as per manufacturer instruction and apllied by approved applicator. complete all as specified and directed.

M&L 75mm thick plain cement concrete (1:3:6) type C1 using 20mm graded stone aggregate as in plinth protection and finishing surfaces of concrete even and smooth including making construction joint at interval of 1.2 mtr & filled with bituminous filler complete all as specified and as directed.

M&L preparing surfaces at wood & wood based materials new or old at any description & girth not otherwise described & treated with tar or coal tar black paint.Complete all as specified and as directed.

M&L preparation of old painted steel surfaces over 10cm width or girth and applying one coat of synthetic enamel paint.Complete all as specified and as directed.

M&L preparation of old painted wooden surfaces over 10cm width or girth and applying one coat of synthetic enamel paint.Complete all as specified and as directed.

M&L preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer.Complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply & fix in repair 20-25mm dia stainless steel curtain rod with two Nos of brackets and decorative end knobs complete for doors/window opening all as specified and directed.

S&F composite 100% solid wood plastic complete (single extended process) material with density not less than 780 kg/cum and plastic wood as in wood chowkhat complete all as per manufacturer instruction.

S&F factory made solid PVC door frame of size 50mm x 47 mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube as specified & directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC stiles and plain colour PVC sheets for top rail, lock rail bottom rail on either side & as gap insert for top rail & bottom rail panneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stile & rails with suitable PVC sheet beading & jointed together with solvent cement all as specified and shown on drawing.Complete all as specified and as directed.

S&F steel work in tubular truss of different size bend to shape, cut to length etc, including necessary welding,special shape washer, conforming to IS:1161-1998 grade St-240 complete as directed by Engineer in Charge.

S&F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. for roof trusses, purlines, rafter etc Fe 410-W (Gde E- 250) quality A complete as directed by Engineer in Charge.

Mild steel plates, plain or chequered, 5mm thick or over in thickness in available sizes for base plates and cleats Fe 410-W (Gde-E 250) qua lity-A complete all as specified and directed by Engineer-in-charge

S&F 12 mm dia MS bolts purpose made with hexagonal or square head on one end and screwed the other, screwed and fitted with nut and washer, length 4 CM complete all as specified and as directed.

Taking down existing aluminium shutter of area exc 1.0 Sqm but not exc 2.00 Sqm and refixing the same in the same opening after reparing and make functional including replacement of fitting and fixture for proper functioning as required all as specified and as directed.

Taking down existing aluminium shutter of area nexc 1.0 Sqm and refixing the same in the same opening after reparing and make functional including replacement of fitting and fixture for proper functioning as required all as specified and as directed.

M&L for Vitrified parking tiles of any colour/patern 40cm x 40 cm x 7 to 10 mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments in floors and over 15 mm thick screed bed in CM 1:4 for laying floor finishes. Complete all as specified and as directed.

M & L for 75 mm PCC 1:3:6 ( 40 m graded stone aggregate) as sub floor , sub base even and rough to recieve the topping layer as in sub base all as specified and directed

M/L PCC 1:2:4 type B1 using 20mm grade aggregate as in coping, leveling course or similar work as directed.

M&L for RCC M-25 B1 1:2:4 (20mm graded aggregate) as in chajja Complete all as specified and as directed.

M&L RCC M-25 Type B1 (1:2:4) (20mm graded aggregate) in slab supported on walls, beams, and columns, in floors, roof, landings balconies, canopies, etc cooking slab and in shelves and the like all a specified and diredted

M&L RCC M-25 type B-1 (20 mm graded stone aggregate) in RCC lintel, band etc complete all as specified and directed.

Formwork to soffits of suspended slabs such as cooking slab and similar work; not exceeding 200mm thick (Horizontal or sloping).Complete all as specified and as directed.

Use & waste form work for flat finished sides and soffits of beams, lintels, chajja cantilevers, shelves etc.Complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and as directed.

M&L TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders cut to length, bent to shape required including cranking bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips.Complete all as specified and as directed.

M&L PCC (1:3:6) Type C-2 using 40mm graded stone aggregate) as in foundation/mass concrete all as specified.

M&L PCC (1:2:4) Type B-0 using 12.5mm graded stone aggregate) as in levelling course concrete all as specified.

M&L 12mm thick clear toughened glass for doors incl fixing accessories for frame in opening as per manufacture's instructions and approval of GE.Complete all as specified and as directed.

Supply and fix GI pipe of dia 25mm to wall/Pole of medium grade with required clamping arrangements to fix with the pole complete and connecting to the existing pipe line all as specified

Supply and fix new gun metal gate valve of dia 25mm with iron wheel all as specified and directed

M&L for galvanised steel tubing in light grade bore 40 mm with all fitting laid in trenches/ fixed with wall/ pole using fixing accessories all as site complete directed by Engr-in-charge.

M&L for Drilling and tapping cast iron water mains (in position) for branch connections of the internal dia 15mm complete all as specified.

S & F double layered Rotational moulded polyethylene water storage tanks 1000 ltrs (cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed. Make- Sintex Note- The cost of connecting inlet and outlet water tube is deemed to be included in the unit rate.Complete all as specified and as directed.

M & L angle iron Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one coat of red oxide primer and two coats of synthetic enamel paint.Complete all as specified and as directed.

M&L for taking up to LT UG cable in all grade/ core/type/make etc after removing connection. complete all as directed.

Supply, laying and testing in replacement of cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core.Complete all as specified and as directed.

Excavation in trenches n.exc 1.5m wide and n.exc and 1.5 mtr in depth getting out in in soft/loose soil all as specified and directed by Engineer-in-charge.

Returning and filling including spreading, leveling, watering and well ramming in layer n.exc 25 CM thick in soft/loose soil all as specified and directed by Engineer-in-charge.

Removing excavated material to a distance not exc. 50 mtrs and deposting where directed at a level not exceeding 1.50mm above the starting point all as specified and directed by Engineer-in-charge.

Supply and laying natural river sand as cushioning of cables, including spreading and punning down all as per clause No 3.21 of SSR part -I complete all as specified and directed by Engineer-in-charge and directed by Engineer in charge Note : punned thickness will only be measured for payment purpose.

M&L for sub class 'B' brick for protection of UG cable in tranches of old size brick all as specified and directed by Engineer-in-charge.

Taking down carefully unserviceable point wiring (light,fans,socket etc) complete incl battens and fittings such as switch, ceiling rose,light fittings, regulatos, socket etc and making good disturbed surface of wall/floor etc complete all as specified.

Taking down DB/main switch of any size and making good disturbed surface of wall/floor complete all as specified.

Taking down sub main wiring of any size complete and making good disturbed surface of walls/floors etc complete as specified.

M & L for taking down fans any type sealing cable ends dismantling blades and removing fan and keeping in safe custody for reuse.Complete all as specified and as directed.

Taking down old U/S LED light fittings/Lamp any type and size.Complete all as specified and as directed.

M & L for point wiring for one light point with 1.5 sqmm cable PVC insulated copper conductor multi stranded as per IS-694 FRLS cable controlled by one way switch, drawn through PVC Casing Capping with all accessories incl 1.5 sqmm multi strand copper conductor cable (green colour) PVC insulated and unsheathed for earth continuity connected to common earth dolly and sunken cast pressed steel terminal box fixed flush to wall of not less than 1.6 mm thick for mounting of fittings such as switch, socket and speed regulator with 3 mm thick Laminated bakelite sheet (Make' Hylum') cover all as specified and directed.

All as per Ser item No.124 above but for 5 amps socket on same board with other switches

All as per Ser item No.124 above but for 5 amps socket on independent board.

All as per Ser item No.124 above but with 2.5 sqmm cables for 15 amps switch socket combination outlet on independent board complete all as specified and directed.

Supply and fix switch 5 amps switch flush type one way single pole.Complete all as specified and as directed.

Supply and fix switch socket combination outlet flush type multi pin 5 amps.Complete all as specified and as directed.

Supply and fix switch socket combination outlet universal type 5 pin 5/16 amps.Complete all as specified and as directed.

Supply and fix ceiling rose surface backelite 65x50 mm having 3 terminal.Complete all as specified and as directed.

Supply and fix ceiling fan regulator Electronic rotary Step type 80 watt single phase A/C 230 volts all complete as specified and directed

S&F PVC angular holder polycarbonate as specified and directed.

Supply and fix Circuit/Sub Main Wiring with 2x4.0 Sqmm PVC insulated, FRLS, copper cable 1100 volts grade stranded copper conductor cable drawn through and including PVC concealed conduit with all fittings and accessories including PVC box (IS-14772) and 1 X 4 Sqmm stranded PVC unsheathed copper cable for earth continuity connected to common earth dolly.Complete all as specified and as directed.

All as per Item No 134 above but 2x6.0 sqmm+1x6.0sqmm earth wire

M/L for Sub main wiring with two run of 10 Sqmm PVC insulated copper cable 1100 volts grade stranded copper conductor cable drawn through and including PVC casing capping / conceled conduit pipe medium grade suitable size with all fittings and accessories including one run of 6 Sqmm stranded PVC unsheathed copper cable for earth continuity and connected to common earth dolly. Note : Two run of 10 sqmm wire with one run of 6 sqmm and one run of casing capaing / conduit pipe shall be measured against one unit and paid to contractor.Complete all as specified and as directed.

Supply and fixing wall mounting industirial socket incl top plug with suitable straight plug, 180 to 250 volts, 2 poles (2P+E) , 20 Amps, Tempra Pro IP 67 to used as single phase industrial load complete all as specified and directed. Make :- Schneider cat No . PKF32W734+ PKE32M723 in equivelent make in L&T/ Seimens/Havells

S & F Factory made sheet metal enclosure for DBs double door (Fixed flush to the wall), SPN, 240 volt, 12 Way, IP-42 protection and suitable for having MCB’s complete and all disturbed surfaces of wall shall be made good to match the existing wall finishes all as specified and directed by Engineer-in-charge. make- L&T/Havells/C&S/legrand/hager.

S & F Power line vertical type TPN DB double door 4 way, IP 43 suitable for MCCB 100 amps CRCA sheet metal enclouser with detachable gland plates for flush / surface mounting with bus bar neutral link and Earth Bar in concealed and all disturbed surfaces of wall shall be made good to match the existing wall finishes complete all as specified and directed. make- L&T/Havells/C&S/legrand/hager.

Taking down old Unsv MCB/MCCB/RCBOs of any type & any capacity complete all as specified and directed

S & F MCB SP 6 to 32 Amp,C series , 230 Volts complete all as specified and directed . Make - L&T/Havells/C&S/legrand/hager.

S & F MCB DP 6 to 32 Amps, C series, 230 Volts complete all as specified and directed . Make - Standard/Havells/C&S

S & F MCB DP 40-63 Amps, C series, 230 Volts complete all as specified and directed. Make - Standard/Havells/C&S

S & F MCB TPN 40-63 10 KA "C" series 415 Volt complete all as specified and directed. Make : L&T/Standard/Havells

S & F MCCB 4 Pole 415V Fixed type 25-100A with breaking capicity 16 KA complete all as specified and directed. Make : L&T/Standard/Havells

Supply and fixing in repair water heater (Geyser) storage type, single phase, energy saving 5 star rated 230 volts grade 3 Ltrs storage capacity complete with fixing accessories.

M&L for painting to ceiling / exhaust fan in two coats over one coat of red oxide primer using syenthetic enamel paint after washing with casting soda water ,scarping to old paint, cleaning etc and identy marking by different colour as per exisiting complete all as specified and directed. Note :- Colour of paint shall be approved by Engr-in- charge.

S& F ceiling fan enery savinf 5 star of sweep not less than 1200mm with hanger in replacement of existed old vintage unseviceable ceiling fan as specified and directed. Make- Crompton/Havells/Bajaj

S&F exhaust fan size of sweep not less than 300 mm copper wounded winding energy saving single phase, 230 volts, 50 HZs with louver, set of sweep and all connecting accessories including making all electric connection using three core PVC insulated copper conductor muilti strandard flexible cable drawn through in PVC flexible conduit pipe from fitting to ceiling rose complete all as specified and directed.

S&F exhaust fan size of sweep not less than 230 mm copper wounded winding energy saving single phase, 230 volts, 50 HZs with louver, set of sweep and all connecting accessories including making all electric connection using three core PVC insulated copper conductor muilti strandard flexible cable drawn through in PVC flexible conduit pipe from fitting to ceiling rose complete all as specified and directed.

Supply and fix , wall mounting fan size of sweep not less than 450 mm heavy duty energy saving single phase, 230 volts, 50 HZs complete all connecting accessories including making all electric connection using three core PVC insulated copper conductor muilti strandard flexible cable drawn through in PVC flexible conduit pipe from fitting to ceiling rose complete all as specified and directed.

Taking up earthing of any size and any depth as existing.complete all as specified and as directed.

Material and labour for earthing complete with copper earth plate electrode 60cm x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below the normal ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to GI earth lead wire 4 mm dia as earthing lead by means of bolts, nuts and washers, check nuts made out of copper all as shown on electrical plate No.5 of SSR Part-I connected to earthing test point complete all as specified and directed.

Supply and fixing recessed dust free LED fitting 24 watts soft light glare free homogenous illumination very high efficiency enviormental friendly long life of suitable for T- grid celing and modular celing application complete making all connection using three core PVC insulated copper conductor muilti strandard flexible cable drawn through in PVC flexible conduit pipe from fitting to ceiling rose complete all as specified and directed.

Supply and Fixing in repairs wall mounted LED batten, polycarbonate housing & integrated electronic driver. LED light fittings flicker free, instant start with uniform light distribution 20W 4 ft indoor decorative with 2 Core copper wire from ceiling rose to light fitting as per Make Havells Cat No LUMILINEBS20WLED865SPCWH or equivalent in Philips/Havells/CG/Orient/Surya all as directed by EIC.

S&F in replacement road/ security light/bldg light with high power LED fitting as light source ,energy saving envoirmental friendly 30 W with advance features all as complete with fixing arrangement such as GI pipe brakets bend in 120 degree, clamps made out by GI strip suitable for steel or PCC poles, nuts ,bolts and washer to be fixing incl making all eclectrical connection with three core flexible copper cable etc specified and directed. Make ; Century LED LTD Coad-SPFL030C in equvilent Bajaj /Philips/ Wipro/Surya

Supply and fixing in replacement of table desk LED 20 watt decorative surface mounting dome shaped pendent in black finishes cool day light complete with all connected accessoreis Make - Havells cat No. LHFHDPE1TN1K020 in equivelent Wipro / Philips/Surya

Supply and fixing in replacement of LED ADORE Lamps 15 W B22 CDL OF 3 STAR Rating including lumen output 1425 (lm) of BALL LAMP for cool day light complete. Make - Havells cat No. LHLDDEEEML8R015 in equivelent Wipro / Philips/Surya/Bajaj

Supplying, installation, testing and commissioning electric motor siren conforming to IS 1941 suitable for three phase 415 V supply with motor not exceeding 3.75 KW power and able to deliver 143 DB noise level. including necessary foundation and protection from Rain/weather of range 2 km 3 phase 415 volts (installed at roof) complete all as specified.

Supply & fixing control cable PVC insulated and FRLS sheathed cable with multi stranded copper conductor of size 2.5 Sqmm 2 core 1 x 1.0 sqmm as earth wire 220V/ 440 volt grade confirmed to IS 1554 for connections of fire alarms, hooters smoke detectors and control panel all as required.

S&F in position MS conduit 25 mm dia of 16SWG including all necessary accessories i.e Tees, bends, elbows, reducers bell mounth tube ends etc. concealed in Wall/false ceiling on surfave as requireed including MS junction box with 3 mm thick bakelite sheet top cover wherever required complete all as specified.

M&L fire alarm control panel complying with BSEN 54 single loop pannel of capacity from 99 detectors and 99 modules upto 200 detector and modules including UPS / Batteries

M&L, installation, testing and comissioning detectors complying with and type certified to EN 45 addresable type microprocessor based programmable intelligent type multi-sensor heat and smoke combination detector photoelectric/ Optical with base with self built intelligence as per IS: 11360 complete all as specified and as directed.

M&L addressable control module.complete all as specified and as directed.

M&L addressable monitor module.complete all as specified and as directed.

M&L addressable mannual call point resettable type.complete all as specified and as directed.

M&L addressable electronic sounder cum strobe.complete all as specified and as directed.

M&L short circuit isolator.complete all as specified and as directed.

M&L Explosiveproof manual call point (add up control module).complete all as specified and as directed.

M&L Remote response indicators.complete all as specified and as directed. Note 1:-The contract sum shall be arrieved at after deducting amount of schedule of credit from the total quated amount. Note 2-Contractor's supervisor and main worker would wear shirt/T-shirt of colour sky blue/brown/yellow preferable embosed with contractor's firm name while carriying out any activities in defence area for better check of security purpose. Note 3:-The tenderer (all eligible contractors) shall ascertain the taxes & levies as on date. The subject tender caters all the taxes & levies as on date including the latest notification of GST issued as on date ( issued by Central Board of Indirect Taxes and Customs)

AVASANA SOLUTIONS PRIVATE LIMITED

D G Corporation

M/S MOHANPASARI

M/S N S CONSTRUCTION

M/S Manjit Singh