Construction of 50 ML Capacity of Raw Water Sump in TP-13 Plot No. 40 at Tarsamiya near Ring road Bhavnagar including 3 month trial period and 2 Years O&M

Grand Total 37 83 23

Earth work excavation for foundation & depositing with an initial lead of 50m & lift

upto required depth in all sort of soils and soft murrum, hard murrum, boulders

including macadam roads, soft rock, masonry in CM or LM or Lime concrete, Hard

1 rock with blasting and chiseling or by chielling only for finishing including Cmt.

dewatering of water as and when required, barricading with safety lamps etc. all

complete as per standard specification as directed by the EIC / approved drawing.

1.1 0 m to 1.5m A.) All type of soil 16496.19 Cmt. 138.66

1.2 1.5m to 3.0m A.) All type of soil 14600.00 Cmt. 151.16

1.3 3.0m To 5.0M A) All Type of soil 19000.00 Cmt. 164.65

1.4 Above 5.0m A) All Type of soil 9500.00 Cmt. 186.95

Boring holes 4.0 m deep in ordinary soil (for cast in situ piles) and getting out the soil

and disposal of the surplus excavated soil as directed within a lead of 50 Meter for

following diameter of pipes.(iii) 300 mm

Filling available excavated earth (excluding rock Black Cotton soil) in trenches. plinth,

3 sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each 6100.00 Cmt. 135.56

disposited layer by ramming and watering.

Supplying and Filling in foundation selected soil in layers of 20cm thickness with

having CBR equal of greater then 8. including watering, ramming and consolidating

4 and upto required lead. complete. For preparation of top layer & require to 6100.00 Cmt. 301.58

prepare the cross section wherever the available width is more than the designed

section as directed by the EIC and approved drawing. Note - for all required lead.

Providing, Supply, and laying of Lime for Soil Stabilisation including Preparation and

leveling of ground, hydrateing spreading or injecting of lime layer and compation

etc. as per site condition and requirements including traspotrtion and fright

Providing and casting in situ C.C. in grade M-15 (approx. corresp. to prop. 1:2:4)

(proportions as per mix design or as per Table 9 of 1IS456 2000 in masses by weigh

batching ) using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work,

including scaffolding centering, form work, needle vibrated consolidation, curing

6 comp. up to 6 meter depth or height (excluding cost of reinforcement and neat 2204 Cmt. 5245.00

finishing) with centering and shuttering/deshuttering etc. comp. for structure for

other than water retaining . with form work

Providing RMC concrete of M-35 grade as per IS: 456 :2000, IS:10262 : 1982 and

7 SP:23 and tender specification (incl plasticizer if needed) in all items with smooth Cmt.

finishing incl. cost of form work and excluding cost of reinforcement

7.1 i) For bottom raft 8497.33 Cmt. 8213.00

7.3 iv) For beams 1082 Cmt. 8486.00

7.4 v) Top Slab 1427.00 Cmt. 8213.00

7.5 vi) Column 735.00 Cmt. 9317.00

7.6 vii) Staircase 18.00 Cmt. 8083.00

Conveying, cleaning, straightening, cutting,bending, placing in position, binding with

M.S. binding wires including providing concrete cover blocks, CRS-500 bars

conforming to IS 1786 (latest revision) and mild steel reinforcement (yield strength

8 2600 kg/cm2) confirming to IS:226 for various concrete members including freight, 1506.00 MT 78577.00

loading,unloading and labour work etc. complete For ESR of brand as per Vendor

Providing and applying 20 mm thick waterproofing cement plaster in cement

mortar 1:2 with neat cement slurry finish with approved water proofing compound

9 in specified proportion inside of container at any height proportion as per 21790.00 Sqm. 202.00

specification including scaffolding, curing etc. complete as directed.

Infinite Civil Solution Pvt. Ltd.

Providing and applying Epoxy paint of approved make to concrete surface for RCC

ESR/ Sump of GSR or any other structure including cleaning the surface by scrapping

and air blowers to the satisfaction of Engineer-in-charge necessary scaffolding etc.

10 complete with all leads and lifts and giving satisfactory hydraulic test for water 21790.00 Sqm. 90.00

tightnessas per IS codes. For new surface - Two coats

Providing and applying 3 coats of acrylic emulsion paint (Weather Coat) to the

exterior surfaces, Apex of Asian Paints or other equivalent of approved make and

shade as per Manufacturer's instructions and specifications including Scaffolding,

cleaning of surfaces, labour, etc. complete to the external surface of tank, beams

&column at any level as directed. Samples shall be got approved before actual

execution of work..

Providing and fixing in position CI cowl air ventilators including fixing of air filter and

jali etc. complete (weight 40 Kg. approx.) dia 150mm

Providing and fixing Fiber reinforced seat and cover in line and level in C.C. 1:2:4 and

finishing Smooth etc. complete as directed. Fiber reinforced Seat and cover Medium

duty.(For Manhole at top slab)

Ultrasonic Level Transmitter : Range 0-10 mt Ultrasonic Type Level Transmitter with

Remote Display : Design, Supply, Installation, Testing and Commissioning of NOn

Contact Ultrasonic Type Level Transmitter with Remote Display, Sensor:The sensor

should be non contact type, field mounting type, housing shall have minimum IP65

protection, PP/ PVC Sensor MOC, with sensor to transmitter cable. Remote Indicator

cum Transmitter: Microprocessor based indicator with LED / LCD digital

display,panel/ wall mounting type, power supply shall be 110-240 Vac or 15 to

Vdc, 50 Hz ± 10 %. Accesories: Mounting bracket, nut, bolts etc as per system

requirement and Hook up diagram of the Instruments. Level Transmitter shall be

suitable for following Range.

providing and fixing water level indicator or depth guage painted TW plank 25 mm

/Ms 4 mm thick float level indicator sliding wire on standarad pullies including

15 necessary arragment to prevent swimming etc. complete with calibration up to 6 2.00 Nos. 5520.00

Providing & laying cement concrete 1:3:6 (1 cement, 3 sand, 6 coarse aggregate) as per

IS:456:2000 and curing complete including cost of formwork for foundation and

16 plinth 266.00 Cmt. 3972.00

Providing and fixing 25 mm dia. M.S. railing with three horizontal rows of pipes and

posts of angle iron of size 65 mm x 65 mm x 8 mm RCC 150 mm and 1.15 m. height

17 and placed at 1.85 m C/C including two coats of oil paint and anchorage in C.C. etc. 6402 Kg. 77.00

Providing Aluminium pole ladder made from channel size 44 mm x 25 mm x 3 mm

and step made from non sleep corrugated aluminium pipe 25 mm dia.complete with

18 rubber shoes at top and bottom available in aluminium for any height. 45.00 Rmt. 992.00

Conveying, carting and removing of the surplus excavated stuff from site to lead

stated below as directed by the Engineer-in-charge including loading, unloading,

19 carting, dumping or spreading etc. complete Upto 10.0 km 34497.00 Cmt. 80.70

Construction of Valve Chamber by doing excavation, refilling the excavated stuff

providing PCC (1:3:6), Brick Work in CM(1:5) using fly ash, RCC (1:1.5:3), TMT Fe

20 10 mm thick plaster in CM 1:3, providing CI steps and FRC manhole frame and cover 6.00 Nos. 53330.00

i) 2000 mm x 2000 mm x 2000 mm for flow meter

Providing and installing copper lighting conductor system with necessary fixtures,

21 material etc. complete as required and as directed. Lightening Arrestor 20.00 Nos. 878.00

Providing and fixing flanged D.I. D.F. K-9 grade pipes vertically ESR / WTP

Connecteting including providing clamps at every 3 mt including jointing materials

such as nuts,bolts,rubber packing,hydraulic testing and necessary scaffolding etc.

complete 450mm dia

Infinite Civil Solution Pvt. Ltd.

Providing and supplying D.I. K-9 grade pipes for following nominal bore diameter

with internal cement mortar lining including all taxes, insurance, transportation,

freight charges, octroi, inspection charges, loading, unloading, conveyance to

23 departmental stores, stacking etc. complete. (IS 8329-2000). Rate for DI pipe based

on Wholesale Price index of Pig Iron as 124.6 for the month of Feb-2021. For

sewerage project cement mortor lining shall be with sulphate resistance cement

23.1 800mm dia outgoing & incoming 1620.00 Rmt. 17090.00

Manufacture, supply and delivery and fixing of ductile iron flange ended specials

complete as per IS : 8329-1994- or its latest revision if any, suitable for D. I. pipe for

various diameter and classes. The rate includes taxes, loading, carting, unloading,

stacking, insurance, Octroi, inspection charges etc. complete.

24.1 a) duck foot bend , cripling flange, bell mouth etc.

Sluice Valve Providing and suppliying, lowering and laying ISI mark DIDF Sluice

valve of following class and diameter including of all taxes , Insurance

25 Transportation, Fright charges , Octroie , Inspection charges, Loading, Unloading

Conveynce to departmental stores, stacking , etc.complete

Sluice Valve (1000 mm dia) (PN-1.0 with hand wheel/

25.1 cap operated pd type short body) 1.00 Nos. 488220.00

Sluice Valve (600 mm dia) (PN-1.6 with hand wheel/

cap operated pd type short body)

Flowmeter:- Design, Supply, installation, testing and commissioning of full bore electromagnetic flow

meter with factory calibration, Inbuilt power operated, flanged connection, flow sensor, Indicator,

Transmitter and totaliser with all accessories viz. surge arrestor, associated cables ,cabinetsm hardware,

etc complete as per following specifications. Size 00 to 800 mm Nominal Bore

1). Flow meter/sensor:

DC pulsed type, IP 68 Protection, Flanged process connection as per IS 1538 or equivalent standard,

SS304/ Metallic Alloy Flow Tube, SS316/ SS 316 L/ Hastelloy Sensor, SS316/ Hastelloy Grounding Ring/

Inbuilt Grounding Electrode, Neoprene/Polyurethane/ Hard Rubber/ Rilsan lining, SS304/ Die Cast

Aluminium/ Carbon steel with Anticorrosive Paint Coil Housing with Junction Box, CS flanges.

2). Flow Transmitter/Converter (Remote Field Mounted): Microprocessor based, Modular design, 2 line

LCD for indication of actual flow rate, forward, reverse, sum totaliser display ±0.5% accuracy at 0.3 to

m/sec velocity, one scalable pulse/ one status, one Modbus output, one GPRS/ GSM output, IP

protection, Die cast aluminium/ polycarbonate/ SS316 with Anticorrosive Paint/ PU finish with glass

window enclosure, Inbuilt EEPROM and Data Logger, 20 meters cable length for sensor to transmitter

communication, Minimum 5 years battery lifetime, 3.6 VDC Non Rechargeable Lithium-thionyl chloride/

Ni-Cd high power batteries, Hourly Basis Worldwide transmission of measured data and events via

e-mail and SMS by integrated GSM/GPRS modem, Reliable data storage facility through integrated SD

card etc alongwith wall mounted/ stand mounted cabinet.

Full Bore Electomagnetic Flow Meter( Inbuilt Battery

Power Operated) -PN

Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block

80mm thick with grade of concrete M300 pnumatic compressed / vibrated

27 mechanically and as per approved design Confirming to IS 15658 : 2006 including 35 1259.00 Sqm. 601.00

mm Sand layer for levelling and filling the joint with sand in proper line and level as

per guidlines of IRC : SP 63-2018 etc. Complete.

Providing, Supplying And fixing Razor Wire / Barbed tape coil Galvanized barbed

wire for security fencing on top of compound wall having GI wire, barb spacing 75-

28 100mm, barb type 4-point /2 point and IS 278-1978 Standard , Height 300-600mm 380.00 Rmt. 380.00

and 450- 900mm dia of coil including vertical post of ms angle of 50x50x3 and

height as per required

Providing fixing new pre-cast concrete kerb stone of gray cement based concrete

block 30cm length,30cm height and 15cm thick of M250 grade concret as per

29 approved design and including excavation for fixing in proper line and level,filling the 800.00 Nos. 209.00

joint with C:M 1:3 (1cement: 3fine sand) ,1 coat primer and 2 coat paint etc

Supplying & fixing big size (upto 10ft ) decorative trees including tree gaurd As

Directed By EIC..

Mud Pump, Max Flow Rate: 5.1LPS, 15mtr head with required pipe incoming and

outgoing(1-2.5 inch Size with Jetting high Pressure Nozzles), cable, starter (Star Delta

/ 3-5Hp Pump Capacity) and panel board (IP-65, Overload Protection,Voltmeter)

Pumps & Machineries 12V Self Priming & Automatic High Pressure Washer with

Adjustable Spray Gun Power Jet Wash Cleaner Pump Wash Kit

Infinite Civil Solution Pvt. Ltd.

Rubble Soling: Providing, Supply, and laying of hard stones stable base to the

foundation and footing including Surface cleaning, Leveling and compaction, Laying

stones, Void filling, Hammering, Compaction etc including trasportation charges.

Providing & Casting in situ C.C. in grade M20 (proportions as per mix design or as per table

of IS 456-2000 in massess by weigh batching) using black trap metal of size

34 6 mm to 20 mm for RCC work, including scaffolding, centering, formwork, needle 274.00 Cmt. 6722.00

vibrated consolidation, curing, etc. complete (excluding cost of reinformcement and

finishing) with centering & shuttering etc. complete for non-water retaining structures

Brick work using common burnt clay building bricks having crushing strength not less than

35 kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:5. (1- Cement : 5 -fine sand)(A) Modular 406 cmt 4550.60

Half brick masonry in common brunt clay building bricks having crushing strength not less than

36 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in foundation and plinth (A) 18 smt 613.91

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an

37 required shape even shade after thoroughly brushing the surface to remove all dirt, and remains 4216 smt 119.07

of loose powdered materials.etc complete

Providing & Applying 2 coats Birla wall care putty of approved equivalent make putty for

smooth finishing of wall with necessary Admixture req.etc the rate shall also include surface

Preparing to make proper line & level etc. complete as directed by engineer in charge.

Providing and laying polished Kota stone slab flooring over

20 mm (average) thick base of cement mortar 1:6 (1 cement : 6 coarse sand) laid over

39 and jointed with grey cement slurry including rubbing and machine polishing etc. complete 54 smt 1009.30

at office area over plinth of HT Rooms, Pump House and chlorine room.

Providing and laying polished Kota stone slab 25 mm thick in riser of steps, dado & pillars,

skirting, laid on 10 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed

with grey cement slurry including rubbing and polishing etc. complete at HT ,LT & Office

Providing and laying white glazed tiles 6mm thick in flooring laid on a bed of 12 mm thick

cement mortar 1:3 and jointed with white cement slurry.

Providing and laying white glazed tiles 6mm thick in skirting, risers of steps and dado on

10 mm thick cement plaster 1:3 and lointed with white cement slurry

Providing and fixing water closet squatting pan (Indian type W.C. pan) size 580 mm x

mm white colour vitreous china long pattern type conforming to IS : 2556 (Part III) together

with 100 mm size vitreous China 'S' trap as per IS : 2556 (Part XIII) both of an approved

make including jointing the trap with the pan and soil pipe in C.

M. 1:1 (1 cement : 1 sand) with 32 dia. C. P. brass half turn flush cock complete including

earthwork, bed concrete of 1:4:8.

Providing and fixing C.P brass screws down stop tap 15 mm dia polished bright , of

approved make and design,with all necessary fittings.

Providing and fixing C.P brass screws down Bip tap 15 mm dia polished bright of approved make

and design ,with all necessary fittings.

Providing and laying(To level or slope) & jointing with stiff mixure of C.M 1:1 salt glased stone

ware pipes of 150 mm dia. Including testing of pipes and joints complete.

47 45 x 60 x 90 CM Chambers for Sewer line 2.00 No 3218.64

Provdg. & laying S.W. Gully trap with brick masonry chamber & water tight G.T.Stone

including fixing of cover Square mouth trap 100 mm x100 mm size P-Trap

Providing and fixing cast iron (Spun) Nahni trap of the following nominal diameter of self

49 cleaning design with C.I. screaed down or hinged grating including cost of cutting and 2.00 No 630.08

making good the walls and floor 100mm inlet and 50mm outlet. 100mm dia.

required wiring & points Electrician charge 3-phase wire (any kind of electrical work)

SITC of Lighting Distribution Board as under:

3 Phase 4 Wire TPN, 6 way Prewired LDB (One each for Indoor & Outdoor Lighting) Suitable

51 to house : Incoming: 32A FP, ELMCB (30mA) Outgoing: 20A SP MCB 'C' curve (9 4.00 No. 5028.81

nos.) & 16A SP MCB 'C' curve (9 nos.)

3C x 2.5 sq. mm. 2XWY/2XFY Cable (For Outdoor light / St. Light) (As per R&B SOR 2012-13, Page

No.-87 Item no. 4-4- 2(a))

Supply, laying and erection of 50 mm approved make Double Walled Corrugated pipes

(DWC) of polyethelene (confirming to IS- 14930 II) with necessary connecting accessoies of

same material at required depth for laying of cable below ground / road surface for enclosing

53 cable and back filling the same to make ground as per original. (For ICP earth pit wire, LT & Street 128.00 Rmt 100.00

Infinite Civil Solution Pvt. Ltd.

INTERNAL WIRING

SITC of Mains & outlet points wiring with 1.1 kV grade FRLS PVC insulated ISI marked

flexible stranded copper conductor wires with medium class min. 25mm. dia. Rigid PVC

pipe and accessories to be erected concealed in / to be run on B70 wall / ceiling with following

sizes as mentioned below. The unit rate wirings shall be with connector, PVC junction box,

54 wires, holder, ceiling rose, angle holder, switch, sockets, switch board, brass 128.00 Rmt 105.93

chromium / cadmium plated machine screws, phase and neutral wires, green Earth continuity

wires etc. as required to complete wiring from LDB panel to the final outlet termination

points. The wiring shall be as per IS:732, IS:4648 and as per tender specification / IS.

(a) SITC of Mains wiring with 4 wire 2.5 sq.mm as per tender specification & IS.

SITC of 6A independent Plug with 2nos. 1.5 sq.mm Cu. Mains size wiring & earthwire of

sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand

copper wires with medium class Rigid PVC pipe and accessories to be erected on wall

/ ceiling, complete with ISI marked 3 / 5 Pin socket and tissino type switch erected with earth

55 continuity connection erected on Metal / PVC box covered with 3 mm thick 10.00 No. 245.76

PC(Polycarbonet) / Acrylic sheet.

56 providing UPVC SCH40 Pipe25 mm 200.00 Rmt 42.37

Providing & fixing in position aluminium fully glazed sliding windows with 15 micron

natural matt brush finish anodised / poweder coating as per over all size shown on the drawings

and aluminium sections of approved make conforming to IS:733 and IS : 1285, made out

of 100.00 mm x 40.00 mm x 1.54 mm thick outer frame section weighing 1.139 Kg/m.,

bottom track sections of 92 mm x

23.30 mm x 1.30 mm thick weighing 1.070 Kg/m., sides and top tracks of 92 mm x

mm x 1.90 mm thick section weighing 0.933 Kg/m., Shutter inter lock of 40.00 mm x

mm x 0.80 mm thick section weighing 0.346 Kg/m. and Shutter top bottom & vertical made

57 from 40.00 mm x 18.00 mm x 0.79 mm thick section weighing 0.289Kg/m fixed with 9.00 smt 4250.00

rawl plugs and screws or with fixing clips, or with expansion hold esters including necessary

filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc.

and aluminium snap beading for glazing / panelling, C. P.brass/stainless steel screws,

including standard anodised aluminium fittings and fixtures of approved make and of adequate

size and in adequate numbers, with 5.5 mm thick wire glass of approved make including

cost and fixing of fixtures etc. complete as per detailed drawings with all lead and

Providing & fixing in position aluminium fully glazed fix ventilator with 15 micron natural

matt brush finish anodised / poweder coating as per over all size shown on the drawings and

aluminium sections of approved make conforming to IS:733 and IS : 1285, made out of

mm x 38.50 mm x 1.95 mm thick outer frame section weighing

1.092 Kg/m. fixed with rawl plugs and screws or with fixing clips, or with expansion hold esters

58 including necessary filling up of gaps at junctions, at top, bottom and sides with required 7.00 smt 3850.00

PVC/neoprene felt etc. and aluminium snap beading for glazing / panelling, C. P.brass/stainless

steel screws, including standard anodised aluminium fittings and fixtures of approved make

and of adequate size and in adequate numbers, with 5.5 mm thick wire glass of

approved make including cost and fixing of fixtures etc. complete as per detailed drawings

with all lead and lifts.

Providing & fixing in position aluminum fully paneled doors with 15 micron natural matt

brush finish anodized as per over all size shown on the drawings and aluminum sections of

approved make conforming to IS:733 and IS : 1285, made out of 102 mm x 45 mm x

mm thick aluminum outer frame section weighing 1.640Kg/m. and shutter sections with

bottom / lock rail 96 mm x 45 mm x

2.7 mm, top rail 48 mm x 45 mm x 2.70 mm weighing 1.38 Kg/m. vertical styles 48 mm x 45 mm x

1.90 mm weighing 0.976 Kg/m. with rounded sides, fixed with roll plugs and screws or with

fixing clips, or with expansion hold esters including necessary filling up of gaps at junctions, at

59 top, bottom and sides with required PVC/neoprene felt etc. and aluminum snap beading for 4.00 smt 4712.29

glazing / paneling, C. P. brass/stainless steel screws, including standard anodized aluminum

fittings and fixtures of approved make and of adequate size and in adequate numbers,

double action floor springs of approved make for each shutter with standard pivot panels of

12 mm thick pre-laminated three layer medium density, exterior grade particle board

(termite proof, water proof and fire proof)Grade 1, Type II conforming to IS :

bounded with phenol formaldehyde synthetic resin, of approved make including cost and

fixing of fixtures etc. complete as per detailed drawings with all lead and lifts.

Infinite Civil Solution Pvt. Ltd.

MCC Panel : MEDIUM VOLTAGE PANEL BOARD (MCC) : S.I.T.C of LV MCC Panel

totally enclosed, dust & bermin proof, indoor type, minimum degree of protection -

IP 52 as per IS: 2147, operation on 3Phase, 4 Wire, 415V, 50Hz, Neutral effectively

grounded, with instrumentation compartments accomodating LED type indicating

lamps, control contactors as per IS: 13947, CT of accuracy class- I as per IS:

relays, meters & control MCBs, air insulated electrolitic grade Aluminum busbar for

three phase & neutral system with incomming breaker- microprocessor based Air

Circuit Breakers (electrically operated drawout type)/ air break fixed type MCCB

with trip free mechanism, current limiting type as per IS: 8828, Motor Contractor (as

per type -2 coordination), Overload Relay with built-in single phasing prevention

feature & auxiliary feeders as per SLD drawings, momentary contact type push

buttons, equipment fittings, bus bars, cable boxes, cable gland, incoming & ougoing

cable connection for 1100V grade, Aluminium/ Copper conductor XLPE/ PVC

insulated & PVC sheathed armoured cable, 10% spare terminals, power wiring using

1100V grade, FRLS insulated copper conductor wires conforming to IS: 694 &

cable compartments/ alleys of minimum 300 mm size, GI earth bus bar for entire

length. MCC shall be fabricated from cold rolled, coled annealed (CRCA) sheet steel

& minimum thickness of various members shall be as follows: Base Frame/ Channel/

Gland Plate - 3 mm, Load Bearing Members/ Doors - 2 mm and Internal Partitions -

Microprocessor based Soft Starter with built-in by pass contactor,Semiconductor

Fuses, Harmonic Filters, cast resin type CT, Digital MFM, Analog Ammeter &

minimum 10 Channel Temperature Scanner with RS 485 communication port. For

APFC PANEL : Supply, installaton, testing & commissioning LV APFC panel consisting

of required capacitor banks for continuous duty to improve P.F. 0.85 to 0.99 in

required steps enclosed in dust & vermin proof compartment, indoor type,

fabricated from CRCA sheet steel with minimum thickness of 3 mm for base frame /

channel / gland plates, 2.0 mm for load bearing members / doors & 1.6 mm for

internal partitions, minimum degree of protection - IP 42, busbar chamber, required

size of Al bus bar/ terminals, minimum 10 stage APFC relay, metering, indicating

lamps, push buttons, with detuned reactor complete IS: 16636-2017 with latest

ammendment & detailed technical specification and data sheet as under. Up to

KVAR capacity: APFC panel consisting following items. Above 50 & up to 100 KVAR:

APFC panel consisting following items. Up to 50 KVAR capacity: APFC panel

consisting following items.

a) 125 A, 50 kA for 1sec. TP, TM based MCCB with spreader terminals & rotary

handle b) 0-125 A range analogue ammeter of 96 x 96 mm size with selector switch

c) 3nos. 125 / 5A, 10 VA CL-1.0 cast resin type current transformer d) Suitable rating

MCCB / MCB &Contactors for each capacitor bank e) Suitable rating APP type

capacitor banks (vacuum impregnated with non-PCB / non toxic oil, internally delta

connected with built in internal fuses complete with discharge resistances &

terminal cover) of approoved make in required steps with well suited detuned

reactor is placed in series with each capacitor step. (e.g., 50 KVAR capacity will be

provided in steps of 2 nos x 5 KVAR, 2 nos x 7.5KVAR & 2 nos x12.5 KVAR). f)

Enclosure. dimensions- 1600 (H) x 1150 (W) x 600 (D)

Infinite Civil Solution Pvt. Ltd.

MEDIUM VOLTAGE PANEL BOARD : S.I.T.C of 5 No.. (4W+1S) 75 KW Auto

Transformer Starter with MCCB, Contactor, O/L relay, cast resin type CT, Digital

MFM, Analog Ammeter, SPP, Timer etc.LV MCC Panel totally enclosed, dust &

bermin proof, indoor type, minimum degree of protection - IP 52 as per IS:

operation on 3- Phase, 4 Wire, 415V, 50Hz, Neutral effectively grounded, with

instrumentation compartments accomodating LED type indicating lamps, control

contactors as per IS: 13947, CT of accuracy class- I as per IS: 2705, relays, meters &

control MCBs, air insulated electrolitic grade Aluminum busbar for three phase &

neutral system with incomming breaker- microprocessor based Air Circuit Breakers

(electrically operated drawout type)/ air break fixed type MCCB with trip free

mechanism, current limiting type as per IS: 8828, Motor Contractor (as per type -2

coordination), Overload Relay with built-in single phasing prevention feature &

auxiliary feeders as per SLD drawings, momentary contact type push buttons,

equipment fittings, bus bars, cable boxes, cable gland, incoming & ougoing cable

connection for 1100V grade, Aluminium/ Copper conductor XLPE/ PVC insulated &

PVC sheathed armoured cable, 10% spare terminals, power wiring using 1100V

grade, FRLS insulated copper conductor wires conforming to IS: 694 & 8130, cable

compartments/ alleys of minimum 300 mm size, GI earth bus bar for entire length.

MCC shall be fabricated from cold rolled, coled annealed (CRCA) sheet steel &

minimum thickness of various members shall be as follows: Base Frame/ Channel/

Gland Plate - 3 mm, Load Bearing Members/ Doors - 2 mm and Internal Partitions -

1.6 mm.size-2200 x 600 x

Approved make Four Pole LT Heavy Duty Switch Disconnector Fuse Unit Cubical Type

suitable for Panel / Wall mounting complete with operating mechanism suitable to

operate on 415V AC with HRC Fuses of suitable load confirming to IS 13947 (Part I &

III) of following capacity. 200 Amp Cat III

MEDIUM VOLTAGE CABLES : Supply, laying, testing & commissioning 1.1 kV grade,

XLPE insulated, stranded Aluminium conductor, galvanised steel flat strip / round

wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on

64 wall surface with necessary clamps / in existing cable trench / cable trays / conduit / 160 mtr 287.00

pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098

(Part-1) & IEC:60502 (Part-1) of following sizes

3.5 c X 70 Sq.mmAL XLPE Armoured (For MVDB to PMCC Panel)

65 1R X 3 c X 50 Sq.mmAL XLPE Armoured (For APFC Panel) 100 mtr 678.00

3 c X 35 Sq.mmAL XLPE Armoured (For PMCC Panel to for each 55 KW motor)

4 C x 6 sq.mm. Al. XLPE ((For WR-DB with TPN MCB at Sump & Pump House,

Outdoor LDB, Indoor LDB, & Auxilury-PDB Feeders. Etc.) )

68 3 C x 2.5 sq.mm.2XWY/2XFY (For Indoor & Outdoor Lighting ) 150 mtr 61.00

CABLE GLAND : Supply, erection, testing and commissioning of Double Compression

Weather proof type Ni-Plated brass cable glands with necessary tools and

equipments as specified in specifications and relevant IS. The glands and Lugs/

Sockets shall be suitable for cable size and type mentioned below & as per

specifications.

3.5 c X 185 Sq.mmAL XLPE Armoured (For TR. to MVDB )

70 3.5 c X 70 Sq.mmAL XLPE Armoured (For MVDB to PMCC Panel) 4 No. 270.00

71 3 c X 50 Sq.mmAL XLPE Armoured (For APFC Panel) 4 No. 720.00

3 c X 35 Sq.mmAL XLPE Armoured (For PMCC Panel to for each 55 KW motor)

4 C x 6 sq.mm. Al. XLPE ((For WR-DB with TPN MCB at Sump & Pump House,

Outdoor LDB, Indoor LDB, & Auxilury-PDB Feeders. Etc.) )

74 3 C x 2.5 sq.mm.2XWY/2XFY (For Indoor & Outdoor Lighting ) 6 No. 73.00

Supplying and erecting Crimping type Aluminium/copper lugs conforming to IS

suitable for cable as below evenly crimped with high pressure tools and connected

75 to switch gear terminal with brass/cadmium plated nuts bolts in an approved 10 No. 21.00

3.5 c X 185 Sq.mmAL XLPE Armoured (For TR. to MVDB )

76 3.5 c X 70 Sq.mmAL XLPE Armoured (For MVDB to PMCC Panel) 10 No. 8.00

77 3 c X 50 Sq.mmAL XLPE Armoured (For APFC Panel) 8 No. 35.00

3 c X 35 Sq.mmAL XLPE Armoured (For PMCC Panel to for each 55 KW motor)

Infinite Civil Solution Pvt. Ltd.

4 C x 6 sq.mm. Al. XLPE ((For WR-DB with TPN MCB at Sump & Pump House,

Outdoor LDB, Indoor LDB, Auxilury-PDB Feeders) )

80 3 C x 2.5 sq.mm.2XWY/2XFY (For Indoor & Outdoor Lighting ) 12 No. 1.00

CABLE TRAY,Trench & Laying : Supply & laying GI ladder type cable trays with side

channels of size - 75 x 15 x 15 mm/ 100 x 15 x 15 mm & rungs of size - 35 x15 x

mm spaced at 250 mm apart, fabricated from 2 mm thick sheet steel in standard

length of 2.5 meter, duly hot dipped galvanized after fabrication as per IS 2629-

1989/ IS 4759-1984 including accessories such as coupler plates/ fish plates, bends,

tees, reducers, elbows, covers and electro-galvanized hardware etc, erected on

existing support as per specification and instruction of engineer in charge.

a) 150(W) x 75(H) x 2.0 mm Thick

82 b) 300(W) x 75(H) x 2.0 mm Thick 120 mtr 388.00

Cable Trench, Laying & Installation of Cable: Making trench in soft soil of suitable

83 width of 90 cms deep for laying cable or locating the fault all over the run and 100 mtr 45.76

backfilling the same and making the surface as normal ground.

Cable Covering in Trench: Covering of cable with second class bricks or cement tiles

laid cover the cable crosswise & also on both sides with covering of 7. 5 Cms. layer of

sand above & below cable (16 bricks per meter) as per IS & Specification. (For HT &

LT cable trench)

EARTHING : Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free G.I.Pipes having Outer pipe dia of 50mm having 80-

200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising,

85 connection terminal dia of 12mm with constant ohmic value surrounded by highly 20 No.. 5701.70

conductive compound with high charge dissipation suitable for following type of

(a) For Electrical installation up to 11 KV in normal soil. Length of Pipe : 2.00 mtrs

Back filling Compound :1 no.(50x25) Bag of 25 Kg (For Transformer ,vcb)

Supplying & erecting earth pit of minimum bore dia.150mm size approved make

Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of

corrosion free G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection

terminal dia of 12mm with constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for following type of applications.

(a) For Electrical Installation covering Transformer Neutrals, Lightning arrester

Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA) i.e

independent Earthing in normal soil. Length of Pipe : 3.00 mtrs Back filling

Compound :2 No. Bags of 25 Kg. (For Transformer netural)

Supplying & erecting earth pit of minimum bore dia.150mm size approved make

Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of

corrosion free G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection

terminal dia of 12mm with constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for following type of applications.

(a) For Electrical installation up to 11 KV in normal soil. Length of Pipe : 1.00 mtrs

Back filling Compound :1 no.(50x25) Bag of 25 Kg (For MVDB)

Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe with necessary

coupling buch buried in specially prepared earth pit & G.I. earth wire of 8 SWG

erected & connected as directed. For using salt and charcoal / coke as required for

pipe type earthing.complete in all respects. ( for PMCC Panel, Motors,APFC)

G.I. EARTH STRIP: Supply, laying and erection of 40mm(w) x 6mm(T) etc. sizes as

required, HOT deep GI Strip including supply & fixing using GI spacers, saddles when

laid inside the building and inclusive of excavation & refilling of earth when laid

outside the building & interconnection with earth pit & all electro-mechanical

equipments. (40X6 G.I Strip wt.1.87 kg/m, 1.87x100Mt.=187kg.) ( for PMCC Panel,

Supply, laying and erection of HOT Dip Galvanized iron strip wire 8 SWG (For LDB,

90 PDB, LCS, lighting, etc.) (8 SWG G.I Strip, 0.101 Kg/m, 0.101 x 100Mt.=10Kg)(for ldb 150 KG 76.27

Infinite Civil Solution Pvt. Ltd.

POINT WIRING : Point wiring for Individual Plug with earthwire of 1.5 sq.mm (Green)

both are of ISI marked 1.1kV grade FRLS PVC insulated multistrand copper wires, in

following type of to be erected concealed in/ on surface of wall/ ceiling complete

91 with Modular type switch & 5 pin Plug erected on PVC/ Metallic box covered with 10 No. 347.46

appropriate front plate modules erected on/ in wall/ ceiling as per pipe erected with

following type of accessories For 6A Plug with 2-1.5 sq.mm Cu. Wire with medium

class Rigid PVC pipe and accessories type of Cat.i.

Point wiring for Individual Plug with earthwire of 1.5 sq.mm (Green) both are of ISI

marked 1.1kV grade FRLS PVC insulated multistrand copper wires, in following type

of to be erected concealed in/ on surface of wall/ ceiling complete with Modular

92 type switch & 5 pin Plug erected on PVC/ Metallic box covered with appropriate 10 No. 516.95

front plate modules erected on/ in wall/ ceiling as per pipe erected with following

type of accessories For 16A Plug with 2-2.5 sq.mm Cu. Wire with medium class Rigid

PVC pipe and accessories type of Cat.i.

LED LIGHT FIXTURES : SITC of Indoor wall mounting LED indoor fitting with LED s of

wattage 0.2 watt to 0.5 watt assembled on single MCPCB with housing used as a

heat sink shall be made of thick sheet steel confirming to IS :513/CRCA polyester

powder coated and high U.V. & corrosion resistance with diffuser and/or Poly

93 carbonate optics with company mark/name 120 to 300V, Power Factor more than 15 No. 686.45

0.9, THD <10%, CCT 4000K to 6500K, Uniformity ration >0.7, Luminare efficancy >

Lumens/watt, LED driver efficiency >85% (Each fitting required LM-79 & LM-80

Certificates) Tube Light with integral/ nonintegral driver 20-22 Watts, Surge - 4KV,IP-

20, 4 feet Cat III

SITC of Surface mounting LED indoor Flood fitting withHigh Power white LED s of

wattage 1 watt to above assembled on single MCPCB, efficiency more than 130lm/w

and corrosion free High pressure die cast ailuminum housing with smooth finish

powder coated and heat sink extruded aluminium with diffuser and polycarbonate

optics/lenses with company mark/ name engraved 120 to 300V, Power Factor more

than 0.95, THD <10%, CCT 5000K to 5700K, Uniformity ration >0.45, Luminare

efficancy > 85 Lumens/watt,LED driver efficiency >85% (Each fitting required LM-79

& LM-80 Certificates) 200 Watt Indoor Flood Light (IP-65), Surge -4KV Cat-III

CEILING FAN : Providing and erecting Approved make 1200mm sweep ceiling fan,

capacitor type, having double ball bearing 450mm down rod, canopies, shackle,

rubber bush, blades, electronic speed regulator, suitable to operate on 230V,50Hz

AC supply conforming to IS: 374/1979.Fan shall be painted with white colour.

EXHAUST FAN :Supplying & erecting single phase approved make industrial exhaust

fan suitable for medium duty ring mounted low noise operation suitable for medium

duty having 380mm dia size and maximum speed in 900RPM as per specifications &

of approved make of category-III for Pumping Station.

SAFETY ACCESSORIES : SITC of following safety accessories complete with necessary

fixing brackets, other accessories and tools etc. as required to complete the

97 job.Supply & Erecting carbon dioxide (CO2) fire extinguisher of 6.5kg capacity with 1 No. 8584.75

necessary clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in wall

complete. (for 1no. LT Room)

Supplying stand first AID box with anticeptic cream, medicine for use on wounds due

burn, crepe bandage, guage bandage, medicated ready to use bandage (Band-aid)

adhesive tape for medicinal user, scissors, anticeptic solution (Savlon or similar) etc.

(All above contents shall be of standard makes) (For Pump house / LT Room)

Providing printed instruction chart both in English and Gujarati and duly framed with

99 front glasses for treatment of person suffering from Electric shock.. (1no. for 1no. 1 No. 127.12

Supplying rubber matting of 12 mm thickness as per IS 5424 and of required length

and breadth with good insulation property for 22 KV (for LT Panel)

Providing and laying broken chine mosek flooring for terrace using 12mm to 20mm broken pieces

of glazzed tiles to be laid over cement mortar 1:3 to plain or slope and to be tempered to bring

101 mortar crème out up to surface using white cement including rounding off junction and extending 8677 Smt. 771.98

them up to 15cm along the wall clearing with water and oxalic acid etc. as directrd.

Supplying and fixing gear operated type, 20 gauge rolling shutter of approved make for the sizes

indicated on drawings including hood cover channel sliding assembly, helical coil springs, brackets,

102 interlocking latches, locking arrangements, painting with 2 coats of enamel paint over one coat of 13 Smt. 4645.76

approved primer paint etc. complete. (A) Shutters having width below 3.5.M.

Infinite Civil Solution Pvt. Ltd.

Providing and fixing window having extruded aluminum Colour Powder Coated section frame

main outer size 95mm x 24mm x 1.17mm @ wt.of 0.738 Kg/mt, horizontal Three track member

size 92mm x 31.75mm x 1.30mm @ Wt.1.07 Kg/mt, vertical member of size 92mm x 31.75mm x

1.50mm ,@ Wt. 1.06 Kg/mt with sliding shutters of horizontal member size 40 mmx18mm

x1.29mm @ wt.of 0.456 Kg/mt, vertical member of size 40mm x 18mm x 1.29 mm @ wt.of

0.456Kg/mt with 5 mm thick transparent bronze colour tinted float glass with powder coated

aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details

Providing Control Pannel Board for submersible Pump set with sutable capactior as per required

104 capacity of pump. 5 No. 13771.00

SUBMERSIBLE CENTRIFUGAL PUMP-MOTOR SET:

Supply, Installation, Testing and Commissioning of Submersible Centrifugal Pump-Motor set for

water with SS CF8M enclosed type Impeller with CI Casing & casing cover, SS 410 shaft suitable

with 3Phase, 415 V. 50 Hz., AC induction dry type submersible motor of mini, rating as specified

having max. 1500 RPM sync, speed, Class F insulation and IP-68 protection. The scope shall include

all required accessories viz. Pump, 250mm dia. 6mm thick MS delivery pipe and MS 500mm dia

Header having thick 8mm in P.H. including MS specials, automatic coupling device, double guide

pipes, chain with shackle, 25Mt. length round submersible Power & control cable, (25m, 4 core

round copper conductor, PVC insulated power cable of reqd size & 1.5 sq mm control cables of

105 required core for each pump motor set) with necessary electrical termination connection at 5 No. 633424.00

junction box / starter panel and precast foundation blocks for auto coupling & delivery bend,

guide pipe etc. as per the specification / IS. (2W+1

Pump Capacity: 950m3/hr. Head: 30 m,

Standbye.) Motor mini. Rating: 110kw / 150HP, (Total flow of three working pump not less than

2850 m3/hr at 30 mt head)

Providing hook of 16 mm dia in the beam for loading & unloading

the E.O.T crane as per requirement and as directed by Engineer in Charge.( R.A)

EOT Crane -Supply, installation, testing & commissioning single girder type fully electrically

operated EOT crane with electrically operated hoist, class II duty, geared travelling trolley with

seven meter lift complete with long travel rail track (40 mm sq. bar), moving or cross girder, all

107 three motions electrically operated by suitable rating motor IP 54, control panel & down pendant 1 set 626250.00

control block, brake, safety device, cables form motor to starter panel & other required

accessories & tested as per IS Specifications Capaciy -5T, Span-9-12m, long -12m asnd lift 6-10m

Mains with isi marked, 1.5KV grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to IS 694 IEC-227 erected in

108 existing pipe af following size specifically for control panel, relays, power 50.00 mtr. 90.00

switchgears, motor starters& control wiring) with required size of copper lugs,

nuts and bolts if required (f) One wire 10.00 sq.mm SOR it. no. 1-4-4F

supplying and Fiexible PVC insulated multistrand multicore 1.1 kv grade ISI marked

109 45.45 Ea 1363 500 copper wires of following size to be erected as directed . e) 1.50 580.00 mtr. 45.00

sq mm 3 core round PVC sheathed SOR it. no. 1-4-5E

providing & erecting 415V MCB Four Pole for Lighting Load(B curve) having 10KA

110 breaking capacity & confirms 1o IS 8828 in existing box having following capacity, 5.00 No. 650.00

(b) 40 Amp Cat - III SOR it. no. 3-10-4

Supplying & erecting earth pit min. dia 150mm size approved make Earthing

Electrode consisting Pipe-in-Pipe Technology as per IS 3043- 1987 made of

corrosion free GI Pipes having outer of 50mm having 80.200 Micron galvanising

Inner pipe dia of 25 mm having 200 250 Micron galvanising, connection terminal dia

of 12mm with constant ohmic value surrounded by highly conductive compound

with high charge applications(a) For Electrical Installation up to 44ov in normal soil

Length of pipe 1 Mtr Back filling compound I Nos Bag of 15 Kg. SOR it. no. 3-14-9A

Providing and erecting XLPE is (IS : 7098) (i)-88 ISI armoured cable multistrand

112 Aluminium conductor or 1.1 KV to be laid on wall with necessary clamps or in 580.00 mtr. 141.00

existing trench / pipe of following size 4 core 10 SQ.MM IT : 4-3-4

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling,

PVC bushes, Check-nuts etc. complete of following sizes.

Supplying and erecting approved make Segment time switch suitable for 230V + 10%

16A. fioating contacts with 24 hour dial having 15/30 min segments with early

manual override switching for on & off without influencing the program sequence

with quartz time switch With power reserve, housed in fire proof thermoplastic

enciosure hansparent cover terminal covers erectod as required wire necessary

connection erected as directed It-6-7-3

Infinite Civil Solution Pvt. Ltd.

Supplying and erecting LED street light / Flood light fittings with High power White

LEDs wattage of 1Watt and above assembled on single MCPCB, efficiency more than

130 lm/w and corrosion free High pressure die cast aluminum housing with smooth

finish powder coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses with company mark/name engraved or embossed

115 to 300 V,Power Factor more than 0.95, THD < 10 %, CCT 5000 K to 5700K, 20.00 No. 4000.00

Uniformity ratio >0.45, Luminaire efficiency> 85 lumens/watt . LED driver efficiency

> 85 %. CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/ BridgeLux (U.S.A.)

make LED used for luminaire. ( Each fittings required LM-79 & LM-80 certificates)

With Bracket & reflective cover - above 24 to 36 watts Cat-lll

Supplying and erecting approved make Octagonal/Round decorative pole made from

HR sheet steel. The pole should be made as per IS. and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable suspend local wind speed with

integral Junction box consist of terminal plate of min 6mm Hylam sheet, standard

profile 35mmX7.5mm Din-Rail for MCB Mounting, and with MCB box stud type

116 terminal and arrangement for cable termination to be erected With Suitable 20.00 No. 9735.00

foundation (Included) as per details given by manufacturer considering site

requirement. - With half Round decorative arm of 0.5meter length as directed by

E.I.C. (A) 7.5 Mtr. Long 70 mm Top X 130 mm bottom dia.3 mm thickness with

200mmX200mmX12mm base plate, 4-M16 Bolts and 450mm long J-Bolt.Approx

LEGEEN Light Black Waterproof Garden Light Gate Light Bollard Light Entryway

Pathway Garden Area Dimensions 30L x 12W x 80H Centimeters

(Pumpset-10HP) Dewatering by pumping set of required capacity including

118 temporary platform carting pumping at site and fixing the same in position including 2350.00 Hour 183.70

all accessories, and fuel and labour etc. complete.

Providing laying and spreading granual material in required proportion so as to have

mix material gradation of GSB grade ll, oncluding sprending in uniform thickness,

rolling with vibratory roller 80-100 kn tatic wt. to proper grade and camber including

watering etc. complet

Providing , laying , spreading and compacting graded stone aggregate to Wet Mix

Macadam (as perv Table 400-10 and 400-11) specification including premixing the

material with water at OMC in machenical mix plant as per approved design mix,

carriage of mixed material by tipper to site, laying in uniform layers with motor

grade/front end loader/ paver finisher in sub base/base course on a well prepared

under base and compacting with vibratory roller to achieve the desired density

including lighting, gauriding barrication and maintenance of diversion et. (MoRTH

specification : ckause 406) By mechanical means

Providing Laying Controlled Reinforced Cement Concrete M 25 using minimum

cement content @ 450 Kg/Cmt. Including curing complete excluding the cost of form

work and reinforcement for reinforced concrete work in concrete reoad coarse and

fine aggregate confirming to IS:383 maximum size of coarse aggregate not

exceeding 25mm using mechanical weigh batcher mixed as per approved mix design,

laid, placed & distributed with sufficient man power using MS side rail of road

thickness with necessary nut bolt plates, fixing as per width, compacted with poker

vibrator (Trimix) & Surface Plate Vibrator, Troweling to be carried out with the same

machine running on troweling blades, finished in a continuous operation including

provision of contraction, expansion, Construction and longitudinal joints, joint filler

separation membrane, sealant primer, joint sealant debonding strip, dowel bar, tio

rod, admixtures as approved, curing compound, finishing to lines and grades as per

drawings/instructions

R. C. C. PIPE (vertically cast)-Providing and supplying ISI Standard R.C.C. pipes(of Sulphate

Resisting Cement) in standard lengths of following class and diameter suitable for either

collar joints or rubber ring joints including all taxes, insurance, transportation, freight

122 charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, 165.00 Rmt 2049.00

stacking Cement vata etc. complete. (IS - 458/ 1989) 600mm dia pipe Class NP3 Test

Pressure 0.7 Kg/sq.cm

Lowering, laying and jointing R. C. C. pipes in C. M. 1:1 1/2 of following diameters in proper

position, grade and alignment at all level as directed by Engineer-in-charge including

conveyance from stores to site of work, labour, giving hydraulic testing as per ISI code. 165.00 Rmt. 228.00

600mm dia pipe Class NP3 Test Pressure 0.7 Kg/sq.cm

Infinite Civil Solution Pvt. Ltd.

Providing and constructing Storm manholes, scraper manholes and unit house connection

chamber, as per the type design as per drawing in brick masonry in C. M. 1:5 and inside and

outside 20mm thick plastering in C. M. 1:3 necessary coping as per drawing with

reinforcement in R.C.C. M200 fixing steps and fixing manhole frame and covers (including

reinforcment and conrete and formwork But excluding supply of manhole frame and covers)

over manholes and house connection chambers and fixing Manhole covers (but excluding

supplying of manhole covers) over scraper manhole etc. complete, providing and fixing safety

chain wherever necessary as per the stipulations in the type design complete as per latest

CPHEEO manual (excl. excavation)

Manhole type "A" Circular type having inside diameter of 1200 mm for depth upto 1.5 m

depth (for any dia sewer)

124.2 Extra depth beyond 1 .0 M but up to 1 .5 M depth for "A" type manhole above. 3.00 Rmt 6628.00

RCC precast M.H. Frame & hollow Cover Manufacture, supply & Delivery at store or at site of

work precast RCC M350 Frame & cover suitable to drainage M.H. and as per type design &

125 Drawing including cost of reinforcement M.S. Angles or Flate, curing,mold work etc.: Suitable 6.00 No. 2638.10

for 560mm dia opening: Heavy Duty Frame as directed by EIC and approved drawing Frame

(EHD-35) & Cover

Constructing Chamber of following size including excavation, refilling, BBCC (1:5:10) for

foundation, C.C.Channel (1:2:4), finished 15 mm thick cement plaster inside in CM 1:3,

finishing with cement slurry, Brick masonary in CM 1:5 & excluding the cost of chamber seat

126 cover etc.completed. 8.00 No. 4374.00

0.75 X 0.75 mt. size (Inside Clear) Depth from

to 1.20 meter for pipe dia <=20 mm

F.R.C. Medium Duty [MD-10] Chamber Covers & Frame- 750 x 750 mm clear opening, The

dimension of frame and cover as per mentioned in Amend No.1 to IS 12592 : 2002 table 1 8.00 No. 1911.00

128 Miscellenious

128.1 Table for operator room As per Instruction of EIC. 1.00 No 15000.00

128.2 steel chairs as per instruction EIC 4.00 No 2500.00

Supplying Steel Cupboard of Size 2'-11" x 6'-0" Godrej brand or Approved

128.3 equivalent brand as 1.00 No 5000.00

specified/Approved by Engineer in charge.

128.4 Electric ceiling Fan as per Vendor list 2.00 No 1441.00

128.5 Tube light as per Vendor list 2.00 No 304.00

128.6 LED Bulb 5Watt as per Vendor list 2.00 No 88.00

128.7 Sintex tank for Toilet Block of 1000 Ltr. as per Vendor list 1.00 No 4000.00

128.8 sofa 3 Seat as per Approved by Engineer in charge. 1.00 No. 20000.00

128.9 FRC Manhole COVER 2.00 No.s 1608.00

Lawn in garden area landscapping including supply , lawn prepration , soil supply labour and take

caring till 45 days

Making hole of following dia pipe in RCC. Rate includes electrical hand operated braker set, gas

129 cutting set with all required equipment & removing debris etc. complete. (00 to 600mm dia ) 15.00 Nos. 1866

suppling and fixing DG Set of 500 KVA / 400 KW (0.8 PF) , Volatage : 415v, 3 Phase, 50 HZ, Engine :

4 Stroke, Diesel, turbocharged , Speed: 1500 RPM, Fuel Tank Approx 990 ltr. , Battery : 24v, Heavy

Duty, oil Capacity : 30-40 ltr. With deital controller (deepsea/comap), size - 3.2x1.4x1.9m and

weight 3400kg and as per standard ISO 8528,ISO 9001 , ISO 14001 including AMF panel Battery

Charger, Rediator Cooling ans acoustic enclosure with CPCB Certified (indian norms). with knop

Providing and supplying double acting C.I.Air valves with isolating sluice valve of approved make &

quality of following class and diameter including all taxes, insurance, transportation, fright

131 charges, inspection charges, loading, unloading, conveyance to departmental stores, stacking 5.00 No. 16536

etc.complete. 200 mm Double Acting Air valve with isolating sluice Valve P.N.1

Unforeseen items from this project which are not included of this tender schedule

Follwing things can be consider in this item:-

1. Extra Item which is execute on site EIC have right to consider item in this on basis of Previling

SOR Rate or if the item is not in the SOR then Mutually Discussion with work agency and finalised

rate of perticuler item (detailed rate analysis of the item shall be submitted and approved with

supporting documents (quatation, GST Bill etc. ) .

2. Extra Work which is Required to execute in this project on site EIC have right to consider item

in this on basis or Previling SOR Rate or Mutually Discussion with work agency and finalised rate

of perticuler item.

Note - The payment shall be done on the basis of work excuted on site and the item which is not

consider in this project.

Infinite Civil Solution Pvt. Ltd.

Name of work - Construction of 50 ML Capacity of Raw Water Sump in TP-13 Plot No. 40 at Tarsamiya near

Ring road Bhavnagar

Water Operation (O.&M.)

Sr No Item Description Qty Unit Rate (Rs) Amount (Rs)

Provide comprehensive operation and

maintenance services for 24 months with all

materials and labour work including all supply of

manpower, repairs and maintenance of all

units,spares,consumables,services of any expert as

required and any other work required for smooth

operation and maintenance of entire facility as per

instruction given by eic.The taxes,insurance of

whole property and staff will be borne by

contractor. O&M period for 1st

Year(Pumpoperator-1+Lineman-1+Chowkidar-1 in

a day with 3 shift in day)

O&M period for 2nd Year(Pumpoperator-

2 1+Lineman-1+Chowkidar-1 in a day with 3 shift in 12 Month 89000.00

Total 2 Year O&M for 24months

Infinite civil solution Pvt. Ltd.