SPECIAL REPAIR TO BLDG NO P-97 AND P-94, PROVN OF CULVERT WITH RCC SLAB AND PROVN OF SEWAGE LINE AND MANHOLE AT KUMAON SCOUTS, PROVN OF SECURITY LIGHT AND CONSTRUCTION OF HARDSTANDING AT MIL STN DHARCHULA

Amount

DESCRIPTION OF ITEMS

Taking down chowkhats or frame exc 1.5 sqm but nexc 4.00 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Demolition of brick work, stone/boulder masonary built in cement mortar complete all specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling wall and ceiling boards (fibre,pulp insulation etc) or insulation boards/slabs/blankets any thickness including cover fillets complete all as specified and directed.

Dismantling timber scantling 40sq.cm and over in section in any position in framed work complete all as specified and directed.

Dismantling timber in fillets,rails posts ,rafters,purlins etc under 40 Sq.cm in section complete all as specified and directed.

Demolition of cement concrete in ground floor,paving nexc 15cm thick(below or above GL) complete all as specified and directed.

Removing demolished material exc. 250 m but n exc. 500 m and depositing where directed.

Dismantling structural steel work including doors, gates etc complete all as specified and directed.

M&L for precast cement concrete block masonary with P.C.C 1:3:6 mix type C-1 block exc 10cm in width and set in CM1:6 complete all as specified and directed.

M &L Rendering 12mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth w/o using extra cement as directed by Engr In Charge.

M &L Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4, finished even and smooth w/o using extra cement as directed by Engr In Charge.

M/L for Joint free non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm and not exceeding 0.18 sqm, in floors over and including 15mm thick screed in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles with as in floor, finished the surface rough to receive tiles complete all as spfd & directed.

M/L for Vitrified ceramic tiles 10 mm thick (Square/Rectangular), light shade, polished area of each tiles tile not exceeding 0.36 sqm, in floors over and including 15mm thick screed in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles with as in floor, finished the surface rough to receive tiles complete all as spfd & directed.

Ditto all same as item No 14 above but for skirtings as including 10mm thick rendering in cement mortar 1:4 on fair face of brick work or concrete surfaces as backing for tiles complete all as specified and directed.

Ditto all same as item No 13 above but for skirtings as including 10mm thick rendering in cement mortar 1:4 on fair face of brick work or concrete surfaces as backing for tiles complete all as specified and directed.

M &L Glazed ceramic tiles colured in vertical surface 450X 300(7-8mm) thickset and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement mortar 1:4 on fair face of brick work or concrete surfaces as backing for tiles complete all as specified and directed.

M&L for Chequered cement concrete colored tiles 20cm x 20 cm x 25 mm thick set, jointed and pointed in neat cement slurry with grey pigment cement and pigments in floor including 20 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

S & F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing all as specified.

S&F Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified.

S & F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S & F powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

S & F of 5.5 mm thick plain sheet glass, ordinary quality and glazing with oil putty or fixed with beads in square in each pane complete all as specified and directed.

S & F brass 4 levers mortice lock, vertical type, size 100 mm complete all as specified and directed.

S&F 150 mm aluminium handles, cast type anodised complete all as specified and directed.

S&F 150 mm aluminium anodised barrel tower bolts extruded section complete all as specified and directed

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple bolt type) and fixing bolts of extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue,anodised with hard drown steel spring, fixed in floors 150 mm long all as specified and directed.

M&L for 12mm thick Prelaminated particle board,interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as spfd and directed.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S & F Aluminium (extruded section body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

S&F 15 mm bore in repair GI tubing with all fittings medium grade fixed to wall or laid in floor etc including taking down old pipe, complete all as specified and directed.

S&F in repair triple layered 500 Ltr rotational moulded polyethylene water storage tanks (cylinderical vetrticle with closed top) hoisted & fixed in position including taking down old tank, complete all as specified and directed.

S&F Ball brass valves 20mm, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Supply only plastic water closet seat, white/ black closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device all as specified and directed by Engr-in-charge.

S&F in repairs vitrous china wash down water closet pan (padestal pattern) white colour(excluding cistern), complete all as specified and directed.

S&F in repairs PVC flushing cistern low level white with inlet pipe,ball valve,float valve and handle including brackets complete all as specified and directed.

S & F in repairs vitreous china wash hand basin, (white), flat back, size 550 x 400mm, including brackets cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

S & F 32 mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S & F 32 mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc. as in waste pipes for wash basins complete all as specified and directed.

S/F in repair 15 mm bore bib taps, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as spfd & directed.

S&F 15 mm dia pillar taps fancy type , cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair toilet paper holder with flat recessed type stainless steel complete all as specified and as directed.

S&F in repairs Health Faucet (ABS Body) MS, Chromium plated suitable for 15mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

S&F in repair 15 mm Stop valves/ angal valve , fancy type, CP, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as spfd & directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm long complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid fixed to wall complete all as specified and directed.

S&F 110 mm PVC (SWR) bends any radius complete all as specified and directed.

S&F PVC (SWR) junction, with access door, single (single T) equal or unequal, for 110 mm bore of pipe complete all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm bore complete all as specified and directed.

S&F PVC (SWR) 'P' trap 110 mm bore complete all as specified and directed.

S&F in repair Aluminium anodised tubular towel rail 20mm dia, D type, 60cm long between flange complete all as specified and directed.

S&F for round Grating 100mm dia with waste hole of PTMT complete all as specified and directed.

M &L for preparation of (previously treated) plastered or unplastered surfaces of walls and applying one coat of oil emulsion distemper any tint on walls complete all as specified and directed.

M&L for Preparing new surfaces, plastered wall surfaces and applying two coat of oil emulsion distemper over a coat of plaster of paris putty of 1mm thckness over plastered surface to prepar the surface even and smooth complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc n. exc 10 sqm on plan and n exc 1.5 m in depth and getting out hard and dense soil complete all as specified and directed.

Returning filling in, approved earth including spreading, levelling, watering and well ramming in layers n.exc 25cm thick, complete all as sspecified and directed.

Removing excavated materials n. exc 50m over and d depositing where directed at a level n.exc.1.50m above the starting point, complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in coping including necessary formwork complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate in surface channel and drain complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, mould, mitred/stopped ends etc complete all as specified and directed.

Add to or deduct from Item No. 66 above for each 25 mm girth or part thereof over or under 30cm complete all as specified and directed.

M&L for precast cement concrete type B1 1:2:4 (Using 20 mm graded stone aggregate) as in cover slabs, manhole cover, chamber cover and drainge cover set in cement mortar 1:6 including necessary formwok complete all as specified and directed.

Taking down cement plaster on brick or stone walls, ect. Including racking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surface in cement mortar 1:4 with water proofing compound, including finishing the surfaces even and smooth (without using extra cement), complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L for 15 mm thick rendering on other than fair faces of brick work or stone masonary surface in cement mortar 1:4 including finishing the surfaces even and smooth (without using extra cement), complete all as specified and directed.

Supply only liquid water proofing compound.

M&L TMT bars, 6 to 8mm, cut to length, bent to shape required including cranking,bending spirally for hooping for column, hooking ends and binding with and incl MS wire(annealed) not less than 0.9 mm dia complete all as specified and directed.

M & L for cutting holes into or through but in brick walls built, in cement mortar or cement lime mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required superficial area exc 400 sq cm but n exc 0.1 sqm complete all as specified and directed.

S&F reinforced concrete pipes, class NP2, 200mm laid and jointed complete with collars, complete all as specified and directed.

M&L for concrete bed 1:4:8 type D-2 (Using 40 mm graded stone aggregate) as in drain pipes including packing under, and haunching against the side of pipes after the are laid and tested in 200 mm bore pipe, complete all as specified and directed.

Earth work in excavation by mechanical means (Hydraulic excavator)/ in all kind of soil in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Earth work in excavation by mechanical means (Hydraulic excavator) means overareas (exc 30 cm in depth, 1.5 M in width as well as 10 sqm on plan) in all kind of soil including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m as directed by Engineer-In-Charge.

M & L for hard core with broken stone/ boulders, broken to gauge n exc 63 mm complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded aggregate) in foundations, filling and mass concrete complete all as specified and as directed by Engr-in-Charge.

Returning, filling in, excavated earth including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

M & L Cement concrete work in pavement/ hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less complete all as specified and directed.

Finishing the surface of concrete road pavement by brooming complete all as specified and directed.

M&L forming construction joint 30mm deep X 10mm wide filled with sealing compound grade A complete all as specified and directed.

M & L reinforced cement concrte M-25 using 20mm graded stone aggregate as in slab complete all as specified and directed.

M & L Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and directed.

Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and directed.

Use & waste of formwork to edges of concrete flats, treads, breaks in floors and roofs ,sides of RCC/PCC bands in walls, horizintal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished surfaces of concretecomplete all as specified and directed.

Supply & Fix mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc. with ends of barsshouldered and / or riveted or forged into spikes, and similar work confirming to Fe 290.Gde-E-165 complete all as specified and directed.

M & L for preparation of new steel surfaces of any description, not otherwise described, over 10cm width or girth, applying two coats of synthetic enamel over a coat of primer complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil complete all as specified and directed.

BLANK

Providing cement concrete 100 mm thick type B-2 (1:2:4) using 40 mm graded agg as in floor, finishing cement concrete surface rough complete all as specified and directed.

Taking down chowkhats or frame n.exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

E/M Items :

S&F steel tubular swaged pole complete with MS base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-31, 09 mtr long, all as specified and shown on drawings including the followings:- (a) Excavation in trenches 1.20 x 0.60 mtr & 1.65 Mtr deep for pole foundation & getting out in any type soil, returning, filling in the excavated soil after fixing the pole in foundation, ramming earth around in layers n.exc 25 cm thick and disposal of surplus soil to a distance n.exc 50 meters. (b) PCC (1:4:8) type D2 using 40mm graded stone aggregate as in base of pole of size 1200mm x 600mm x 150 mm all as specified and directed. (c) PCC (1:3:6) type C2 using 40mm graded stone aggregate as in foundation 1200mm x 600mm x 1500 mm (sub base as mass concrete) for concrete encasing the pole up to GL all as specified and directed. Contd....

(d) PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in coping of size 300x300x300 including necessary form work (e) Painting of poles externally with one coat of bituminous paint (upto planting depth) and above plinth block concrete collar with two coat of aluminum paint over one coat of red oxide primer including preparation of surface including painting of (f) The portion above coping shall be painted in alternation bands of black and yellow colour (each band of 30 cm wide) by two coats of super enameled paint upto 1.5m height.

Supply and fixing and testing complete as existing poles/walls aesthetically Designed SMD LED Street light luminaires of 45 watts System wattage for energy saving having IP-66 degree of protection ,With minimum system efficiency as > 85 % ,made of Pressure die cast aluminum housing powder coated in graphite grey and heat resistant thoughned glass with excellent thermal management including PVC cable connector. LED's should have lens optics and vandal proof prismatic poly carbonate covers for ensuring efficient optics and uniform distribution of light. Fitting should have operating voltage range of 120 - 270 VAC , THD <10% , P.F >.95 .The fitting should have in built surge protector of 5 KV, complete all as specified and directed.

S&F factory made weather proof outdoor pole mounted MCB kiosk box made out of not less than 1mm thick MS sheet size not less than 240x130x110mm with and including MCB SP 6 Amp, 240 V 'C' series 10 KA and bus bar including fixing with two FI clamp 25x3mm including washer nut bolt etc duly painted complete all as specified and directed.

Supply & Fixing street light bracket made out of 40 mm bore light grade GI pipe bent to shape fixed as bracket suitable for street light fittings not less than 1.2 m long bent/welded to shape including necessary nut, bolt and clamp-02 No made of MS flat 40x5mm as reuired duly painted by unscrewing nut and bolts complete all as specified and directed.

M&L service connection 1100 volts grade heavy duty cable with PVC insulated aluminium stranded conductor served with an inner sheathing of PVC tape armoured with overall PVC sheathed twin core 2.5 sqmm nominal cross sectional area complete all as specified and directed.

Supply and fix time switches 415 V three phase of 20 Amp rating with contactor fitted inside sheet metal enclosure complete all as specified and directed.

Supply, laying, testing and commissioning XLPE insulated, armoured heavy duty electric cable with aluminium stranded conductor, served with inner sheathing of PVC tape armoured with galvanised steel wire overall PVC sheathed 1100 volts grade, cross-sectional area 10 Sqmm 4 core complete including taking up complete all as specified and directed.

Excavation in trenches in hard/dense soil n exc 1.5m wide and exc1.5m but n. exc 3.0m deep and getting out including forming bottom surfaces to required level or slope for laying pipe/ cable complete all as specified and as directed by Enge-in-charge befor returing filling the earth.

Returning filling in excavated soil in trenches including spreading, leveling watering and well ramming in 25cm thick layer complete all as specified and as specified and as directed.

Removal of surplus excavated soil to a distance exc50 m but not exc in 100 m and deposited where directed at a level exc 1.5m above the starting point complete all as specified and as directed.

M & L for Sand cushioningng (dry sand) to under ground cable for cable protection provided with layers 8cm thick before laying and 15cm thick after laying the cable and punned down to 23 cm thickness complete all as specified and directed. Note : For payment purpose punned thickness of 18cm shall be measured against spread thickness of 18cm as mentioned in para19.75 of SSR Part-I

Supply and laying sub class B bricks old size for protection of cables laid lengthwise perpendicular to the axis of cable, adjecent to each other complete all as specified and directed.

Supply, fixing & laying of 25 mm dia bore GI tubing, light grade with and including all fittings and fixture like socket, nipple, elbow, reducer etc complete laid in trenches or on pole for cable protection complete all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60 × 60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron strip 25×4mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel protected by 40 mm bore GI pipe (medium grade) all as shown in electrical plate No. 3, connected to earthing test point all as specified or indicated including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 40x40 Cm x 6Cm reinforced with 8 mm dia deformed bar @ 5 cm c/c with one handle for lifitting made out of 8 mm dia MS bar, funnle, wire mesh, 20 mm bore GI pipe (medium grade) for watering including charcoal and salt in alternative layers necessary excavation and earth work in any type of soil and testing complete all as shown on electrical plate No-3 of SSR part-I, 2009.

Note : Tenderers may note that amount of credit Rs 16,046.00 will be deducted from the total amount arrived, at the time of Acceptance of contract.

M/s Karki Krishna Singh

SHAHJEE FRIDGE SERVICE