REPAIR TO ROAD AND ROAD SIDE FURNITURE OF NHO UNDER AGE B R III AT GE CLEMENT TOWN DEHRADUN

Amount

M&L for Preparation existing black top surface by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc and applying evenly a primer/tack coat with paving bitumen grade VG-30 @ 5Kg/10sqm complete all as specified and as directed

M&L for providing bituminous premixed semi dense asphaltic concrete with 5.5% binder content by weight of total mix, 30 mm consolidated thickness using Viscosity Grade Bitumen VG-30, rolled to required camber, gradient and super elevation with 8 to 10 tonne power roller, mixed in hot mix plant and spread with mechanical paver, complete all as specified and directed. (Notes : (i) The mix design shall be got done from approved lab and got approved from GE before commencement of work. (ii) In the event of variation in the mix design in the percentage of binder content on minus side, the difference in quantity of binder content will be adjusted through supply only rate at market rate or procurment rate whichever is more for paving bitumen VG-30. However no plus adjustment shall be applicable if excess quantity of binder content is used/approved in the execution of work under this item.

M & L for preparation of road surfaces and applying thermoplastic reflective paint for marking of minimum 2mm thick single coat as in center line and edge line zebra crossing, stop lines etc, road marking of 150/100mm width using "HOT Mark" thermoplastic paint (Hot application) white or yellow by indigenous modern propelled road marking machine as directed including all ingredients such as blinder, glass beads, titanium diaxide, calcium carbonate, inter filler etc, thermoplastic requirement for glass beads shall be as per the table No 800.4 of most specification conforming to BS-6086 OF MOST specification including spraying of glass beads @ 300 Gms/Sqm etc all as per manufacturer's instructions and as directed.

S&F in repair Road Stud (Cat Eye) of size100x100x26 mm body made of ABS body dynamically desgined very high impact strength non breakable polycarbonate with electronically welded prismatic retro- reflective lense on both sides for maximum retro-reflection in wet and dry condition. Body shall be dust proof. I .e non dust accumulation on lense and space shall be built for finger grip, including fixing with bitumen adheshive BT-69 complete all as specified and directed by Engineer-in-charge.

S&F in repair solar cat eye/studs of size 125x125x25mm(shank 60mm) with alluminium alloy shall high efficiency Mono-Crystalline solar panel 2.40V/0.30 Watt having one NI-Mh or NI-cd rechargable battery (1.2V/1600MA). Six super bright LEDs with 10000 to 18000 mcd(Millicandela) having flash rate 2 Hz and bearable weight 10 tons approx with view distance up to 1000 meters of any colour i.e yellow ,red,blue,green or white as required at site working temp 10-50 degree calcius,working time 3 to 4 days after fully charged battery,charging time 5 to 6 hrs from direct sub light maintenance free,unbreakable, poly carbonate clear facing, automatically turn on at night and turn off at day including all fixing arrangements as per manufacture instruction complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) and including removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (Using 40mm graded stone aggregate) as in path/hardstanding finishing the top surfaces even and rough to receive top layer complete all as specified and directed

M&L rubber moulded (coloured glossy finish) factory made with vibratory table method,precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness , M-40 grade (ISI Marked ), including and over 25 mm thick sand cushioning for laying of inter locking tiles (paving blocks) complete all as specified and directed (Note : Design/shade of rubber moulded machine presses precast concrete Paver block shall be as approved by GE/Engr-In-Charge.

M&L for preparing new or previously untreated concrete surfaces of walls of any description over 10 cm width or girth, not otherwise described and applying two coats of weather proof exterior paint over a coat of primer, complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in kerb/coping and other similar work including necessary form work and the like including weathering, slightly rounded or chamfered angles and throating,complete all as specified and as directed

S. Kumar & Company

M/s Himanshu Tyagi