SPL REPAIR TO BLDG NO. P-208 AND P-209 (OR LIVING) OF CERTAIN UNIT AND BLDG NO. P-153 AND P-154 (O8 Dus) JCOs MD ACCN OF CERTAIN UNIT AND OR MD ACCN BLDG NO. P-150 AT ARMY AREA BANAR UNDER GE BANAR

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc. complete all as specified and directed by Engr-in-charges.

All as per srl item No. 01 above but width n.exc 15cm. complete all as specified and directed by Engr-in-charges.

S&F winodws/ventilators (ECO-4000 series double rebate) fabricated from roll framed section made of galvanised steel colour coated/powder coated (Base steel as per IS 513 'D' quality galvanised as per IS 277 with zinc of 120gms/sqmtr) with total coated thickness of 0.60mm, with or without cooler opening. complete all as specified and directed by Engr-in-charges. Note. Paint Specification : Coated sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted with polyester up to 50-60 microns thick. Dimenstions of Sections: Sections for frame should be of 72mmx55mm, section for mullion should be of 72mmx50mm, sections for shutter frame should be of 47mmx20mm, sections for fixed glass bead should be of 12mmx12mm, and section for fly mesh should be of 40mmx20mm. Fixing Details: Sections for frame glazed shutter and mesh shutters should be cut to length and miter joined with polyprpylene corner brackets, mullion section should be joined with frame/mullion using mullion cap Ethyl Propylene Damien Monomer (EPDM) Gasket should be used all around glass in shutter and fixed glass. Spoon Profile should be used around fly mesh to fix mesh in mesh shutter. Accessories: Each Glazed shutter and mesh shutter should be provided with SS Pivot Hinges-1set, seccolor handle & seccolor stay. Window frame should be fixed to brick/concrete masonry by using Nylon self expanding caps and driving MS electroplated 80mm long screw into the caps through frame.

S&F glass shutter & fixed glass portions should be provided with a glass of 5mm plain float glass complete all as specified and directed by Engr-in-charges.

S&F wire Mesh shutter should be provided with a stainless steel 32 gauge fly mesh of 304 grades with 144 holes per square inch complete all as specified and directed by Engr-in-charges.

S&F window grill should be provided with Grill made of 10mm sq. MS Bars welded to at 150mm centre to centre, 6mmx12mm MS flat, Total Grill unit should be powder coated and fixed to window frame with screw complete all as specified and directed by Engr-in-charges.

S&F 200mm long Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed by Engr-in-charges.

M&L for complete removal of existing treatment on walls and applying two coats of oil bound distemper over a one coat of 1mm thick JK/Birla wall putty over plastered surface to prepare the surface even and smooth and over priming plastered and other surfaces with alkali resistant priming paint complete all as specified and directed by Engr-in-charges.

M&L for preparation of old plastered or unplastered surfaces of walls and applying two coats of white wash complete all as specified and directed by Engr-in-charges.

M&L for preparation of old plastered or unplastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed by Engr-in-charges.