DEVELOPMENT OF AMTS NEW BUS DEPO AT BOPAL GHUMA ROAD AHMEDABAD

SR. NO. ITEM DESCRIPTION UNIT TOTAL QTY RATE AMOUNT

Excavation for foundation upto 1.5 m depth including sorting out

and stacking of useful materials and disposing off the excavated 1364.00 115.92

1 stuff upto 50 Meter lead.(A) Loose or soft soil cmt

Excavation for foundation for depth from 1.5 mt 3.0 m including

sorting out and stacking of useful materials and disposing off the 689.00 128.52

2 excavated stuff upto 50 Meter lead.(A) Loose or soft soil cmt

Conveyance charges of earth lime, murrum, building rubbish,

manure, garbage, sludge, excavated rock, fly ash, aggregate of 430.00 235.51

3 any kind etc. comp. upto 5 km lead. cmt

Extra For Lead Above 5 km & upto 6 km cmt 86.00 9.39

Extra For Lead Above 6 km & upto 7 km cmt 86.00 9.39

Filling available excavated earth (excluding rock) in trenches.

plinth, sides of foundations etc. in layers not exceeding 20 cm. in

depth consolidating each disposited layer by ramming and

4 watering. cmt

Filling in plinth with sand under floors including watering

5 ramming, consolidating and dressing complete cmt

Filling in foundation and plinth with murrum or selected soil in

layers of 20cm. thickness including watering, ramming and 22.00 286.20

6 consolidating etc. complete. cmt

Carring out plinth treatment to post construction /existing

structure by spraying chemical solution for termite control

treatment including labour and material consistment with I.S.I

specification. Using Chlordene and Chiorpurfiles 20 EC. As Per

6131_paret-II Consentration Weight one percent is 108.00 104.90

recommended i.e one litre 20 EC chemical emulsion with 19 liter

give 1% concrentration inclusive of one litre chemical emulsion

appication at the rate of 5 Litre chemical /Sqm of sur face is

7 recommended as per I.S Smt

Providing and laying cement concrete 1:3:6 (1-Cement:3-

coarsesand:6-hand broken stone aggregates 40mm nominal

size)and curing complete excluding cost of formwork in (A)

8 Foundation and Plinth. Cum

Providing and laying controlled cement concrete M.250 and

curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in (A) Foundations,

9 footings, Base of columns and Mass concrete. FOOTING Cum

Providing and laying controlled cement concrete M.250 and

curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in (A) Foundations, 30.00 4238.04

footings, Base of columns and Mass concrete. BELOW PLINTH

Providing and laying controlled cement concrete M.250 and

curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in (D) Columns, 43.00 4593.91

Pillars posts and struts, upto floor two level.GROUND FLOOR

11 ABOW PLINTH GROUND FLOOR COLUMN Cum

Providing and laying controlled cement concrete M.250 and

curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in (C) 265.00 4496.07

Slabs,landing,shelves,Balconies, Lintels, Beams, Girders and

12 Cantilever upto floor two level. plith beam Cum

Providing and laying controlled cement concrete M.200 and

curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in © 23.00 4460.36

Slabs,landing,shelves,Balconies Lintels, Beams, Girders and

13 Cantilever upto floor two level. GROUND FLOOR Cum

Providing TMT Bar FE 500D reinforcement for R.C.C. work

including bending, binding and placing in position complete upto 77782.00 75.46

14 floor two level Kg

Providing formwork of ordinary timber planking so as to give a

rough finish including centering shuttering strutting and propping

etc. Height of propping and centering below supporting floor to

ceiling not exceeding 4 M. and removal of the same for in situ

reinforced concrete and plain concrete work in. (A) Foundations

15 Footings Bases of Columns etc. and Mass concrete. FOOTING Smt

Providing formwork of ordinary timber planking so as to give a

rough finish including centering shuttering strutting and propping

etc. Height of propping and centering below supporting floor to

ceiling not exceeding 4 M. and removal of the same for in situ 30.00 252.00

reinforced concrete and plain concrete work in. (B) Flat surfaces

such as soffits of supspened floors slabs Landings and the like. (1)

16 Floors etc. upto 200 mm in thickness. CEILIING Smt

Providing formwork of ordinary timber planking so as to give a

rough finish including centering shuttering strutting and propping

etc. height of propping and centering below supporting floor to

ceiling not exceeding 4 M. and removal of the same for in situ 824.00 297.68

reinforced concrete and plain concrete work in. (G) Columns

PillarsPosts and struts. (1) Square Rectangular Polygonal in plan.

Providing formwork of ordinary timber planking so as to give a

rough finish including centering shuttering strutting and propping

etc. height of propping and centering below supporting floor to

ceiling not exceeding 4 M. and removal of the same for in situ

reinforced concrete and plain concrete work in. (H) (2) Sides and

soffits of Beams Beam Haunchings canti-levers Girders

Bressumers and Lintels exceeding 1M.in Depth.PLINTH BEAM &

18 SLAB BEAM & LINTEL& COPING Smt

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation and

plinth in Cement Mortar 1:5. (1- Cement : 5 -fine

19 sand)(B)Conventional Cum

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation and

plinth in Cement Mortar 1:5. (1- Cement : 5 -fine sand)(B) 107.00 4283.91

Conventional Extra for brick work in superstructure above plinth

20 level upto floor two level (B) Conventional : Ground Floor Cum

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation and

plinth in Cement Mortar 1:5. (1- Cement : 5 -fine sand)(B) 6.00 4324.00

Conventional Extraforbrickworkinsuperstructureaboveplinth

21 level upto floor two level (B) Conventional : First Floor Cum

(i) Half brick masonry in common brunt clay building bricks

having crushing strength not less than 35 Kg/Sq.Cm. in Cement

mortar 1:4 (1- Cement : 4 -coarse sand ) in foundation and

plinth 143.00 646.70

(B) Conventional Extra for half brick masonry in superstructure

above plinth level upto floor two level. (B) Conventional GROUND

Providing 15mm thick cement plaster in single coat on Rough

(Similar)side of single or half brick walls for interior plastering

upto floor two level and finished even and smooth in (ii) Cement 69.00 155.61

mortar 1:4 (1-cement :4-sand) GROUND FLOOR

Providing 10 mm thick cement plaster in single coat

onbrick/concrete walls for interior plastering upto floor two level

and finished even and smooth in (ii) Cement mortar 1:4 (1-

cement :4-sand) Extra over items 1 to 69, 71 to 87 and 90 for

interior plastering above floor two level for every additional

24 storey height. (1) Single coat plaster FIRST FLOOR Smt

Providing 10mm thick cement plaster in single coat on

brick/concrete walls for interior plastering upto floor two level

and finished even and smooth in (ii) Cement mortar 1:4 (1-

cement :4-sand) Extra over items 58 to 71 for plastering on

ceilings and sofits of stairs up to floor two level instead of

25 plastering on walls.CEILING Smt

Providing 20 mm thick double coat mala cement plaster on

interior brick / concrete work for plastering comprising of base

coat of 12 mm thick cement plaster in cement mortar (1 Cement :

4 coarse sand) in rough finishing and 8 mm thick top coat of

cement mortar 1:2 (1 Cement : 2 Coarsesand) finished with trovel

26 including scaffolding curing etc. complete. Smt

20mm thick sand faced cement plaster on walls upto height

metres above ground level consisting of 12mm thick backing coat

of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of

27 C.M. 1:1 (1-cement : 1-sand) etc. complete. Smt

Providing and applying 2mm thick Texture Plaster Terre Plaette

(Specturm , Coral or equivalent) incoprating fine fillments made

of polymer and aggergating natural stone powder with making

grooves on base coat of 20 mm thick smooth mala plaster (which

paid seperately) etc. complete.Colour and shade as approved by

28 Architect/ Engineer in charge for at all floor ,all height. Smt

Providing cement vata (10cm. x 10 cm. size) quarter round in

cement mortar 1:1 including neat cement finishing, watering etc. 28.00 23.45

29 complete. Rmt

Applying two coats of putty & two coats of primer of approved

brand and manufacture on new wall surface to give an even

shade including thoroughly brushing the surface free from mortar

30 dropping and other foreign matter and sand papered smooth. Smt

Wall painting (two coats) with plastic emulsion paint of approved

brand and manufacture on undecorated wall surface to give an

even shade including throughly brushing the surface free from 133.00 78.44

mortar droppings and other foreign matter and sand papered

Finishing wall with weather proof exterior emulsion paint on wall

surface (two coats) to give an required shape even shade after

thoroughly brushing the surface to remove all dirt, and remains

32 of loose powdered materials.etc complete Smt

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand)

on new surface or fixing on existing flooring by adhesive material

including dismentaling of existing flooring and jointed with color

cement slurry including finised with flush pointing & cleaning the

33 surface etc. complete for light shade Smt

P&L 24"x24" vitrified 8mm thick tile flooring over 20mm

(average) base of cement mortar 1:6 (1cement :6 coarse sand) on

new surface or fixing one xisting flooring by adhesive material

including dismentaling of existing flooring and jointed with color

cement slurry including finised with flush pointing & cleaning the

34 surface etc.complete for antiskid Smt

Providing and laying Granite slab (18 mm thick) one side polished

flooring over 20 mm (average) base of cement mortar 1:6 (1

cement : 6 coarse sand) or L.M 1:1.5 laid and jointed with grey

35 cement slurry including rubbing and polishing complete. Smt

Providing and laying 18 mm thick polished granite stone machine

cut in single piece (Max. available) in sill and jambs of door

,window,ventilation & lift wall cladding,staircase flooring landing,

risers & treads, skirting laid over 10 mm thick cement mortar 1 :

3 (1 cement : 3 coarse sand) and jointed with grey cement slurry 14.00 3248.00

with matching pigment incl. rubbing and polishing,half rounding

edge and incl. fixing of hilty fastener at every 1/3 span of sill as

required size etc. complete colour and shed as approved by

36 architect engineer in charge. Smt

Providing and laying polished Kota stone slab flooring over 20mm

(Average) thick base of cement mortar 1:6 (1-cement : 6-coarse

sand) or L.M. 1.1.5 laid over and jointed with grey cement slurry

37 including rubbing and polishing etc. complete. (B) 30 mm thick Smt

Providing and fixing M.S. grills of required pattern to wooden

frames of windows etc. with M.S. flats at required spacings and

frame alround, square or round bars with round headed bolts and 81.00 100.17

nuts or by screws (A) Plain Grill.

Providing and fixing standared extruded of alluminium section of

size 63mmx 38.10 mm x 1.2mm @Wt.0.643Kg /mt with colour

anodized alluminium frame for ventilation with 5mm thick

39 frosted glassas details etc complete for Ventilation. Smt

Providing and fixing window having extruded aluminum Colour

Powder Coated section frame main outer size 63.50 x 38.10 x

1.95 mm,@ Wt 1.094 Kg / Rmt, horizontal two track member size

61.85 mm x 31.75 mm x 1.20mm @ wt.of 0.695 Kg/mt, vertical

member of size 61.85 mm x 31.75mm x 1.30 mm @ wt.of 0.0.659

Kg/mt with sliding shutters of horizontal member size 40mm x

18mm x 1.29mm @ wt.of 0.456Kg/mt, vertical member of size

40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt with 5 mm thick

transparent bronze colour tinted float glass with powder coated

aluminum fittings and fixtures and transparent silicon sealant

glass fixing to frame as per details etc

40 complete for window Smt

Providing and fixing flush door both sides laminated and I.T.W.

beading all around by using I.T.W. frame 120 m.m. x 80m.m..

shutter 35 mm thick solid core malemine faced three layered pre

laminated flat pressed wood based exterior grade bonded

BWP/BWR synthetic resin having stamped IS 12823 grade I type II

including three coats of lacquer polishing to exposed wooden

surfaces and Stainless steel decorative type designs fixtures /

fastening etc.including I.T.W. triangular batten patti of size

30m.m.x30m.m.etc. as per architectural detailed drawing and as

41 directed by engineer in charge. Smt

Providing and fixing FRP frame size 125x65mm and 35 mm thick

FRP shutter with wood grain raised pannel edde sign finish

shutter having extra reinforcement on sides & edges in Gel coat

finish. The core of the shutter & frame is to be filed up with

injected polyurethene foam done in situa long with embedded

wooden pieces for stiffening & also taking hinges & fintures. The

whole FRP frame &shutter is to be water proof weathe rproof

,termite proof & resistance to mild acid/alkali. Rate sare to be

inclusive of S.Shinges with fastener sleeve & alluminium fixtures

42 & fastenings. Smt

Providing & applying CHEMICAL WATER PROOFING treatment to

the terrace including Surface cleaning: All surface shall be

thoroughly cleaned with mechanical means or wire brush to

remove dust dirt & all loose portion from the surface of terrace &

parapet wall.& wash with water. Surface preparing: All cracks will

be opened in V-shape & sealed wirh Dr Fixit Crack X Paste & any

patch work will be repaired with polymer modified mortar,

providing and applying two coat of Dr.Fixit pidifine 2K on entire

inside area of sunk. Two coat of Dr.fixit pidifine 2K(10 kg Powder

+ 5 lit Liquid) shall be applied on ready surface in vertically &

horizontally direction which is brsh applied waterproofing coating

& provides excellent impermeable coating & flexible enough to

take care of minor cracks in concrete & plaster & good adhesion

43 with cementitious surfaces etc. completed by EIC. Smt

Providing and laying broken chine mosaic flooring for terrace

using 12 mm to 20 mm broken pieces of glazed tiles to be laid

over cement mortar 1:3 to plain or slope and to be tempered to

bring mortar creme out upto surface using white cement

including rounding off junctions and extending them upto 15 cm

44 along the wall,clearing with water and oxalic acid etc. as directed. Smt

Structural steel work ( Confirming to IS 4923-1997) riveted,

bolted or welded in builtup for all type sections, in framed work,

including cutting, hoisting, fixing in position and applying a 420.00 126.68

priming coat of approved steel primer all complete as per the

45 structural designs and directions of Engineer in charge. Kg

Painting one coats (excluding priming coat) on previously printed

steel and other metal surface with synthetic enamel paint,

brushing to give an even shade including cleaning the surface of

46 all dirt, dust and other foreign matter. Smt

Paver Block Providing and laying shot blasted Non - interlocking,

Paver blocks of specified thickness, size, grade of concrete and

colour machine made and blasting by automatic shot blasting

machine and high density of as per approved sample of approved

make for footpath, parking areas, service lanes,cross over and

other areas as mentioned in the drawing. Including providing and

laying 50 mm thick averave bedding layer of coarse sand below

paver block as per required grading and specification. Laid paver

block shall be mechanically compacted. The work of the paving

blocks shall be executed in line and level by skilled mason of

flooring work only. Small size of paver block with same

specification shall be used at residue or at end. It should be laid in

such a way that the no cutting of the paver block to be necessary.

If cutting of paver block shall be required , than cut by machine

only and laying to be done by skilled flooring mason. The finished

surface of the paver block shall have coarse sand Texture Finish.

Pave blocks shall be compacted and shall be re-laid if necessary.

47 Actual laid area shall be measured and paid without any wastage. Smt

Pre cast concrete kerb Providing and fixing M25 Grade of

concrete precast exposed / Fair finish / texture finish kerb stones

of approved make as per approved sample of any size and any

type. Kerbs shall be fixed on the foundation prepared as per

approved design. The rate shall also include for erecting and

fixing the pieces in position for complete kerb system with

chamfered type of kerbs including necessary accessories of kerb

like radius kerbs, angles and quadrant kerbs, droplet kerbs etc. 110.00 912.50

complete as per drawing. Kerb shall be fixed as paper joint

without any jointing material. However cement mortar shall be

provided at the backside of kerb stone joint. (Sample must be

approved) Cost of excavation, cutting , base , side filling shall

includes as directed engineer - incharge in above item description

as per BOQ (b) 380 x 600 x 150 mm high Footpath kerb. As per

48 approved rate Rmt

Providing & Laying P21(water reducing concrete admixture at

100 ml per bag of cement & recon 3 s fiber at 125 gm per bag of

cement including making C channel 75 x 75 mm required to

maintain level,slope and thickness of the concrete road leveling 1500.00 175.00

of placed concrete with surface vibrator and finishing with power

floater & trowel light brooming the surface & Groove cutting &

49 filling of expansion joint as directed by Engineer in charge. Smt

Providing, laying, spreading and compacting Wet Mix Macadam

(as per table 400 - 10 and 400 - 11) of well graded stone

aggregate to specification including premixing the Material with

water at OMC in mechanical mix plant as per approved design

mix, carriage of mixed material by Tipper to site, laying in uniform

layers with motor grade/Front end Loader/paver finisher, in sub

base/base course on a well prepared under base and compacting

with vibratory roller to achieve the desired density including

lighting, guarding, barricating and maintenance of diversion etc.

50 (MoRTH specification : Clause 406) by mechanical means Cum

Providing and laying rubble soling, 23 cm thick, in a compact

manner, foudation, road, footpath etc. using 200 to 230 mm. cut

size stones, covering and levelling the surface with a layer of

murrum after filling the voids with smaller sized stones or stone

chips, including watering, ramming well and consolidating each

51 layer, as directed. Cum

Providing Forming groove of uniform size Vertical & Horizontal

line in the top layer of Exposed R.c.c Surface as per approved

pattern using Cutter bled to thunder layer, including removal of

All Dust repair to the edges of panels and finishing the groove

complete as per specifications and direction of the Engineer-in-

Providing & Fixing the Chikenmesh - 20 guage(Crimp Jali) of

approved size applying between the RCC and masonry junction in

proper line, level and plumb with all material, labour, tools, 13.30 284.85

tackles and equipment. Including providing and fixing the jali with

53 nails, etc complete as directed by the site-incharge. Sqmtr

Providing corrugated G.I. sheet of class-3 roofing fixed with

glavanished iron J or L Hooks, Bolts and nuts 8mm diameter with

bitumen and G.I. limpet washer or G.I. limpet washer. filled with 317.00 719.93

white lead complete excluding the cost of purlins, Rafters and

54 Trusses.(1) 0.80 mm thick sheet. Sqmtr

Providing and fixing 1.20 Metre high fencing with 2.0 Metre long

M.S. Angle posts 40mm x 40 mm x6 mm and oil painting 3 coats

fixed at 2.5 Mt,C/c. with five Horizontan lines and two diagonals

of galvanised steel barbed wire weighting 9.38 Kg. per 100 Metre, 195.00 385.40

strained and fixed to posts with G.I,staples including fixing the

postsin ground with 0.5 M x 0.5.M x 0.5 M. block in C.C1:5:10 etc

55 complete. RMT

Providing & fixing of reinforcement bars ( reiforcement bars shall

be paid extra under relevant item of work ) after drilling the hole

of required diameter & depth ,cleanning of the same ,providing

/filling the hole with Injection Mortar (HIT HY 150 of Hilti or

approved equivalant ),inserting reinforcement bar etc. complete

as per Manufacturers & architects instruction.The work shall be

carried out by the technical workmens/agency approved by the

manufacturer and under technical supervision of Manufacturer of

Injection grout including all materials,tool tackles ,labour

56 etc.complete

12 mm. dia.bar -Holes 14mm dia Depth 120mm Nos 50.00 196.00

16 mm. dia.bar -Holes 20mm dia Depth 160mm Nos 50.00 251.00

20 mm. dia.bar -Holes 25mm dia Depth 200mm Nos 50.00 306.00

CORE CUTTING-Core cutting creates precise, circular holes in

concrete structures like walls, floors, and slabs- Core cutting

often utilizes diamond-tipped blades, which are effective for

57 cutting through hard materials like concrete NOS

Removing and scraping of old deteriorated plaster of any

thickness fromm wall / R.C.C member including stacking of

serviceable material and disposal of unserviceable from site of

58 work with all lead and lift Sqm

Demolition of Brick work and stone masonry including stacking of

serviceable materilas and disposal of unserviceable materials 150.00 544.95

59 with all lead and lift.(ii) In Cement Mortar. Cmt

Dismentaling tiled of stone floors laid in mortar including stacking

of serviceable materilas and disposal of unserviceable materials 250.00 47.25

60 with all lead and lift. Sqm

Dismentling doors, windows, ventilators etc. (wood or steel)

shutters including chowkhats architraves, holdfasts and other

attachment etc. complete and stacking them within all lead and

61 lift.(ii) Exceeding 3 Sq.M. in area. Each

Demolition including stacking of serviceable materilas and

disposal of unserviceable materials with all lead and lift. (i) R.C.C. 100.00 1047.38

Providing and fixing concealed center point to wall ceiling & floor

CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF)

seal for potable water of following dia. nominal bore tube fittings 100.00 165.21

and clamps including making good the wall, ceiling and floor etc.

63 complete.[A] 15 mm. Rmt

Providing and fixing concealed center point to wall ceiling & floor

CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF)

seal for potable water of following dia. nominal bore tube fittings 150.00 202.97

and clamps including making good the wall, ceiling and floor etc.

64 complete. [B] 20 mm. Rmt

Providing and fixing concealed center point to wall ceiling & floor

CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF)

seal for potable water of following dia. nominal bore tube fittings 125.00 247.25

and clamps including making good the wall, ceiling and floor etc.

65 complete. [C] 25 mm. Rmt

Providing and fixing concealed center point to wall ceiling & floor

CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF)

seal for potable water of following dia. nominal bore tube fittings 125.00 330.37

and clamps including making good the wall, ceiling and floor etc.

66 complete. [D] 32mm. Rmt

Providing and fixing concealed center point to wall ceiling & floor

CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF)

seal for potable water of following dia. nominal bore tube fittings 125.00 437.66

and clamps including making good the wall, ceiling and floor etc.

67 complete. [E] 40mm. Rmt

Providing and fixing concealed center point to wall ceiling & floor

CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF)

seal for potable water of following dia. nominal bore tube fittings 30.00 647.30

and clamps including making good the wall, ceiling and floor etc.

68 complete. [F] 50mm. Rmt

Supplying & erecting resin bonded flap rock wool / glass wool

with conductivity valve 1.67 sq.mm per watt & to with stand the

temp. to 100 degree centigrade C thickness 50mm with G I pipe

of following size dia "B" class as per IS:1239. The plastic sheet to

be used as covering of glass wool. Al. cladding besides other

materials like chicken mesh, 26 G Al. Sheet shall be used for

69 cladding the insulation pipe.

(A) for 20 mm dia pipe Mtr 30.00 360.00

(B) For 25 mm dia pipe Mtr 20.00 440.00

(C) for 32 mm dia pipe Mtr 20.00 530.00

(D) for 40 mm dia pipe Mtr 45.00 620.00

(E) for 50 mm dia pipe Mtr 5.00 760.00

Providing and fixing Gun metal check or non-return fullway wheel

70 valve.(C) 20mm dia. Each

Providing and fixing Gun metal check or non-return fullway wheel

71 valve.(C) 25mm dia. Each

Providing and fixing Gun metal check or non-return fullway wheel

72 valve.(E) 40mm dia. Each

Providing and fixing Gun metal check or non-return fullway wheel

73 valve.(E) 50mm dia. Each

Providing and supplying C.I. Air valves of approved make &

quality of following class and diameter including taxes, insurance,

transportation, freight charges, octroi, inspection charges, 2.00 661.00

loading, unloading, conveyance to departmental stores, stacking

74 etc. complete. Air Valves single (S2) Type 25mm Each

Providing and fixing mosquito proof stainless steel overflow

grating for tanks.(// 2.00 2000.00

75 Audco/Lehry/ R.B./ Spirex) 100mm dia. Each

Consruction of Valves chambers in brick or bela stone masonry,

locally available in C.M. 1:6 foundation concrete 150mm thick in

CC 1:4:8 of trap metal size 25mm to 40mm thick, inside cement

plaster in CM 1:3 and cement pointing outside in C.M. 1:3 and top

cover of precast RCC slab 100mm thick with key hole in two parts,

each with handles or MS Bar etc. complete as given size) Upto

Mt. depth from G.L. to pipe invert level incl. complete civil works 3.00 5380.00

but excl. cost of excavation and refilling with cast in situ RCC slab

in one single piece with fixing of CI-MH Frame and cover (excl

cost of CI-MH Frame and cover) with 23mm thick brick masonry

wall in CM 1:6 (d) size of chamber 0.60 m x 0.60m and 1.0mt deep

with precast slab in two parts 15mm with single piece 10cm with

76 fixing MH Cover. Each

Supply, installation, Testing and Commissioning of 15mm

Nominal diameter Garden Hydrant with gun metal Ball Valve, GI

pipe for Flexible hose Connection Provision and

77 all required accessories etc. Each

Providing erecting and fixing double coated Syntex PVC. (ISI)

water tank of required capacity each with all necessary fittings 2005.00 4.60

78 and connection etc. complete on terrace. litre

Supplying and erecting chromium plated heavy duty

brass valve for inlet pipe of water heater 15 mm 4.00 180.00

Supplying and erecting 15mm brass non-return valve for

80 inlet pipe of storage water heater. Nos

Supplying and erecting dead pressure releasing valve for

storage type water heater with necessary 4.00 380.00

81 materials. Nos

Providing & erecting fibre reinforced PVC flexible pipe

with brass locking nuts & washers & clips at both 5.00 180.00

82 ends complete erected without leakage Nos

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression type 150.00 100.49

fittings, wall clipsetc. including making good the wall ceiling and

83 floor.(C) 32mm Rmt

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression type 150.00 116.40

fittings, wall clipsetc. including making good the wall ceiling and

84 floor.(D) 40mm Rmt

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression type 100.00 124.43

fittings, wall clipsetc. including making good the wall ceiling and

85 floor.(E) 50mm Rmt

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression type 100.00 332.91

fittings, wall clipsetc. including making good the wall ceiling and

86 floor.(G)110 mm Rmt

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure polythene pipes of the following outside Dia.

Low densidy, complete with special falnge compression type 100.00 274.68

fittings, wall clipsetc. including making good the wall ceiling and

87 floor.(F) 75mm Rmt

Providing and fixing PVC SWR Nahni trap IS 14735 for drain -

mm diameter with jali of the following nominal diameter of self

cleansing design with C.I scread down or hinged grating including

88 the cost of cutting and making good the walls. each

Providing and fixing PVC SWR Nahni trap IS 14735 for drain -

mm diameter with jali of the following nominal diameter of self

cleansing design with C.I scread down or hinged grating including

89 the cost of cutting and making good the walls. each

Providing and fixing S.W. gully trap with C.I. grating brick masonry

chamber and water tight C.I. cover with frame of 300mm x

300mm size (inside) with standard weight.(i) Square mouth traps.

90 (A) 100mm x 100mm size P type. (upto 10 ton) Each

Providing & Supplying of Class SN8 structured wall Polythelene

piping systems (Pipe with online/offline coupler and elastomeric

sealing ring) with non-smooth External Annular corrugated and

smooth internal surfaces (Double Wall) for non pressure

underground Sewerage & Drainage application as per EN:13476-3 50.00 208.00

incuding all local and central taxes, transportation, freight

charges, octroi, inspection charges, loading, unloading,

conveyance to the departmental stores etc. complete (ID Dia).

91 Pipe Dia. ID 100mm Rmt

Providing & Supplying of Class SN8 structured wall Polythelene

piping systems (Pipe with online/offline coupler and elastomeric

sealing ring) with non-smooth External Annular corrugated and

smooth internal surfaces (Double Wall) for non pressure

underground Sewerage & Drainage application as per EN:13476-3 50.00 373.00

incuding all local and central taxes, transportation, freight

charges, octroi, inspection charges, loading, unloading,

conveyance to the departmental stores etc. complete (ID Dia).

92 Pipe Dia. ID 150mm Rmt

Providing & Supplying of Class SN8 structured wall Polythelene

piping systems (Pipe with online/offline coupler and elastomeric

sealing ring) with non-smooth External Annular corrugated and

smooth internal surfaces (Double Wall) for non pressure

underground Sewerage & Drainage application as per EN:13476-3 50.00 738.00

incuding all local and central taxes, transportation, freight

charges, octroi, inspection charges, loading, unloading,

conveyance to the departmental stores etc. complete (ID Dia).

93 Pipe Dia. ID 200mm Rmt

Providing & Supplying of Class SN8 structured wall Polythelene

piping systems (Pipe with online/offline coupler and elastomeric

sealing ring) with non-smooth External Annular corrugated and

smooth internal surfaces (Double Wall) for non pressure

underground Sewerage & Drainage application as per EN:13476-3 50.00 1004.00

incuding all local and central taxes, transportation, freight

charges, octroi, inspection charges, loading, unloading,

conveyance to the departmental stores etc. complete (ID Dia).

94 Pipe Dia. ID 250mm Rmt

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement

:2-coarse sand : 4-graded stone aggregate 20mm nominal size)

foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick

bats 40 + 50mm size) inside plastering 15mm thick with Cement

Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating

coat of neat cement and making channels in cement concrete

1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm

nominal size) finished smooth complete including curing and 2.00 10920.76

festing (i) Inside size 900mm x 1200mm and 1.5M. deep including

C.I. cover with frame size 560mm diameter total weight of cover

and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and

Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry

using brick having crushing strength not less than 35Kg. /

Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (1) A

95 type depth 0.90 Metre for 150mm diameter sewer. Each

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement

:2-coarse sand : 4-graded stone aggregate 20mm nominal size)

foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick

bats 40 + 50mm size) inside plastering 15mm thick with Cement

Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating

coat of neat cement and making channels in cement concrete

1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm

nominal size) finished smooth complete including curing and 2.00 19139.07

festing (i) Inside size 900mm x 1200mm and 1.5M. deep including

C.I. cover with frame size 560mm diameter total weight of cover

and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and

Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry

using brick having crushing strength not less than 35Kg. /

Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (2) B

96 type depth 1.50 Metre for 150mm diameter sewer. Each

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine

sand :10-Graded stone aggregate 40mm nominal size) bedding

for stoneware pipes of following internal diameters with 80.00 211.59

necessary formwork and curing complete.(B) 150mm dia.

97 (166mm Ave. bed thickness) Rmt

Constructing brick masonry chamber for underground C.I.

Inspection chamber and bends with briocks having croshing

strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame

(Light duty) 455mm x 610mm intenal dimensions total weight of

cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.)

and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-

cement :2- coarse sand :4-graded stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm thick with

cement mortar 1:3 finished smooth with a floating coat of neat

cement on walls and bed concrete etc. complete.(i) Inside

dimensions 455mmx 610mm and 450mm deep for single pipe

98 line. (upto 10 ton) Each

Providing and fixing G.I. Rain water spout of 50mm dia. and 30cm.

99 length. Each

Constructing Brick masonry road gully chamber 500mm x 450mm

x 600mm including 500mm x 450mm C.I. horizontal grating wih 2.00 1573.95

100 frame complete.(upto 10 ton) No.

Constructing brick masonry road gully chamber 1100mm x

775mm including 500mm x 450mm (C.I. horizontal grating with 2.00 1997.20

101 frame and vertical grating complete.) (upto 10 ton) No.

Providing & Supplying of Class SN8 structured wall Polythelene

piping systems (Pipe with online/offline coupler and elastomeric

sealing ring) with non-smooth External Annular corrugated and

smooth internal surfaces (Double Wall) for non pressure

underground Sewerage & Drainage application as per EN:13476-3 50.00 208.00

incuding all local and central taxes, transportation, freight

charges, octroi, inspection charges, loading, unloading,

conveyance to the departmental stores etc. complete (ID Dia).

102 Pipe Dia. ID 100mm Rmt

Providing & Supplying of Class SN8 structured wall Polythelene

piping systems (Pipe with online/offline coupler and elastomeric

sealing ring) with non-smooth External Annular corrugated and

smooth internal surfaces (Double Wall) for non pressure

underground Sewerage & Drainage application as per EN:13476-3 40.00 373.00

incuding all local and central taxes, transportation, freight

charges, octroi, inspection charges, loading, unloading,

conveyance to the departmental stores etc. complete (ID Dia).

103 Pipe Dia. ID 150mm Rmt

Providing & Supplying of Class SN8 structured wall Polythelene

piping systems (Pipe with online/offline coupler and elastomeric

sealing ring) with non-smooth External Annular corrugated and

smooth internal surfaces (Double Wall) for non pressure

underground Sewerage & Drainage application as per EN:13476-3 35.00 738.00

incuding all local and central taxes, transportation, freight

charges, octroi, inspection charges, loading, unloading,

conveyance to the departmental stores etc. complete (ID Dia).

104 Pipe Dia. ID 200mm Rmt

Providing & Supplying of Class SN8 structured wall Polythelene

piping systems (Pipe with online/offline coupler and elastomeric

sealing ring) with non-smooth External Annular corrugated and

smooth internal surfaces (Double Wall) for non pressure

underground Sewerage & Drainage application as per EN:13476-3 30.00 1004.00

incuding all local and central taxes, transportation, freight

charges, octroi, inspection charges, loading, unloading,

conveyance to the departmental stores etc. complete (ID Dia).

105 Pipe Dia. ID 250mm Rmt

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine

sand :10-Graded stone aggregate 40mm nominal size) bedding

for stoneware pipes of following internal diameters with 50.00 211.59

necessary formwork and curing complete.(B) 150mm dia.

106 (166mm Ave. bed thickness) Rmt

Providing and fixing wash down water closet (European type,

W.C. Pan) with integral P or S trap including jointing the trap with

soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and 2.00 1290.80

cover to be measured and paid for separately) (A) vitreous China

107 Pattern :(i) in white colour Each

Providing and fixing 12.5 Litres low level flushing cistern with a

pair, of C.I. or Mild brackets, complete with fittings such as lead

valve less syphon, 15mm nom.nal size brass ball valve with

polythene float, C.P brass handle unions and couplings for

connections, with inlet, outlet and overflow pipes, 40mm dia. 2.00 2321.21

porcelain enamelled flush bend including cutting holes in walls

and making good the same connecting the flush bend with cistern

and closet (overflow pipe to be measured and paid for

108 separately)(A) Vitreous China (I) In white colour Each

Providing and fixing plastic seat and cover for wash

down water closer with C.P. brass hinges and 2.00 288.45

109 rubber buffers. (B) Black plastic seal and cover. Each

Providing and fixing washbasin with single hole for pillar tap with

C.I. or M.S. brackets painted white including sutting holes and

making good the same but excluding fittings.(A) Vitreous 3.00 1400.18

China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In

110 white colour. Each

Providing and fixing C.P. brass waste for washbasin or

111 sink. (B) 40mm dia. Each

Providing and fixing M.I. fisher union for washbasin or

112 sink. (B) 40mm dia. Each

Providing and fixing 100mm sand cast iron grating for

113 gully, floor or Nahni trap. Each

Providing and fixing 600mm x 450mm bevelled edge mirrror of

superior glass mounted on 6mm thick A.C. sheet or

plywood sheet and fixing to wooden pluge with C.P.

114 brass screws and washers. Each

Providing and fixing 600mm x 120mm glass shelf with C.P.

brass bracket and guard rail complete mixed to 3.00 561.03

115 wooden plug with C.P. brass screws. Each

Providing and fixing toilet paper holder.(A) C.P. Brass

Providing and fixing screw down bib taps of following

size.(B) Brass chromium plated screws down Bib 3.00 212.68

117 Tap. (i) 15mm dia. Each

Providing and fixing pillar tap, capstan head, screw

down high pressure with screws, shanks and back 3.00 305.67

118 nuts. (i) 15mm dia. Each

Providing and fixing chromium plated brass half trun flush cock

of approved quality including fixing in pipe line etc. 30.00 252.26

119 complete.(i) 20mm dia. Each

Providing and fixing chromium plated brass half trun flush cock

of approved quality including fixing in pipe line etc. 3.00 261.16

120 complete.(ii) 25mm dia. Each

Providing and fixing Urinal or approved quality including

conecting the Urinal with waste pipe , tap etc.

complete.(A) White earthenware flat back or

121 corner type size 430mm x 260mm x 350mm. Each

Providing and fixing Rubber plug for sink or wash basin.

Providing and fixing chromium plated, bottle

necessary couplings of approved quality for wash 3.00 292.87

123 basin. Each

Providing and fixing ball cock of approved. quality as

124 directed.(A) Copper Metal (ii) 50mm dia. Each

Providing and fixing Angle Cock with screw, back

nuts all necessary fittings etc. Completed

(Cera-CM108/ Parryware-T9939A1 / Hindware-

Providing and fixing water closet squatting Pan (Indian type W.C.

Pan) size 580mm (Earthwork, bed concrete, foot reste and trap to

be measured and paid for separately) (A) Vitreous China. (1) Long

126 pattern = White colour Each

Providing and fixing 12mm dia. Health faucet with 8 mm dia of

JAQUAR / HINDWARE/ CERA or approved make selected by

Architect with flexible pipe of 1mt. length and holding stands

127 complete. Model Equivalant to Jaquar- CAT - ALD-577. Each

Supplying & erecting approved make self-priming domestic

monoblock water pump with 1.5 H.P motor, suitable for

operation on 230 volts, 50c/s. AC supply with metallic flange, and 2.00 9222.00

M.S. impeller delivery and following discharge 44 LPM at 32 Mtr

128 head suitable 25 mm dia delivery Ea.

Providing and erecting ISI marked PVC insulated PVC Sheathed

Flat flexible Submersible copper cable approved make of 25.00 145.00

129 following Size. (C) 3 Core x 4 Sq. mm Mtr

Supplying & erecting ISI Marked (Embossed) following size of “C”

Class G.I . Pipe & erecting as directed by Engineer-in-charge with 25.00 210.00

130 necessary plumbing as desired. (C) 40 mm dia Mtr

Supplying and erecting with leak proof materials, M.S. Heavy duty

ISI marked coupling having threads of 8 TPI/11 TPI suitable for ‘C’

class pipe to take load of pump and pipe assembly of following

131 size andTPI :- (A) 40mm( 1.5") dia. pipe 8 TPI Ea.

Supplying & erecting G.l. bend for pipe connections suitable for

Supplying & erecting ISI Marked G.l. Elbow for pipe connections

132 suitable for (C) 40 mm (1.5") Ea.

Supplying and erecting Direct On-line Electronics Starter with 2-

5/4-10/8-14/10-16 Amp. Rating relay (variable current setting)

directly operated in totally insulated elegant enclosure and

Amp. Rating power relay with start - stop button for single phase

operation up to 3 HP as per complete erected on P.W. Block with

following features.

Low voltage cut off below 140 V

High voltage cut off above 280 V

Overload protection

133 Indicating LEDs for motor on lv, hv & overload tripping. [Cat.II] Ea.

Supplying & erecting approved make Automatic liquid level

controller 6A. with sensor testing as per instruction of Engineer in

charge on site complete with wiring connection with existing 1.00 2332.00

wires , with copper conductor from pump to upper and lower

Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multistrand copper wires, in following type of pipe to

be erected concealed in/ on surface on wall/ceiling complete

with 6A Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC / Metallic box, single

mounting base frame covered with textured/metallic front plate

modules erected on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector as directed.

135 (a) with medium class Rigid PVC pipe and accessories CAT III Pt

Point wiring for secondary light point with 2-1.5 sq.mm &

earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multistrand copper wires, in following

type of pipe to be erected concealed in / flushed on wall/ceiling,

complete with earth continuity and necessary connection with

primary light with accessories erected on Metal / PVC box

covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet for

open / concealed wiring. with necessary Lamp holder / ceiling

rose / H.D.Connector as directed. (a) with medium class Rigid PVC

136 pipe and accessories Pt

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm

(Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated

multistrand copper wires, in following type of pipe to be erected

concealed in / flushed on wall/ceiling complete with 6A Modular

type switch and hum free EME four or more step type electronic

fan regulator with separately mounted and accessories with 10.00 593.00

earth continuity of following type erected on PVC / Metallic box,

single mounting base frame covered with textured/metallic front

plate modules erected on / in wall / ceiling as per pipe erected.

with necessary ceiling rose / H.D.Connector as directed. (a) with

137 medium class Rigid PVC pipe and accessories.CAT III Nos

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multistrand copper wires, in following type of to be erected

concealed in / on surface of wall / ceiling complete with Modular

type switch & 5 pin Plug erected on PVC / Metallic box covered 125.00 441.00

with appropriate front plate modules erected on / in wall / ceiling

as per pipe erected with following type of accessories. For 6A

Plug with 2-1.5 sq.mm Cu. Wire with medium class Rigid PVC pipe

137 and accessories CAT III Pt

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multistrand copper wires, in following type of to be erected

concealed in / on surface of wall / ceiling complete with Modular

type switch & 5 pin Plug erected on PVC / Metallic box covered 10.00 663.00

with appropriate front plate modules erected on / in wall / ceiling

as per pipe erected with following type of accessories.[III] For 16A

Plug with 2-2.5 sq.mm Cu. Wire (a) with medium class Rigid PVC

138 pipe and accessories.CAT-III Pt

Providing & erecting Switch board for Computer or electric

apparatus consisting of following items in single board erected

on PVC / Metal board with 3 mm thick PC (Polycarbonate) /

Acrylic sheet erected as directed for [B] modular type accessories 3.00 1071.00

1 no. 6A/16A universal plug-switch combined. CATIII

3 nos. 6A Switch

139 3 nos. 6A 5 pin Plug Ea

Providing and erecting ISI mark Medium class RIGID PVC PIPES of

following size complete to be erected on/in wall or ceiling

erected with necessary PVC fittings & Junction boxes fixed with

adhesive solution & Clamps with following dia of pipes, in

140 approved manner as directed

MAINS WIRING AND CONDUIT

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded

Copper conductor wire in following type of pipe to be erected

concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for

earth continuity of following size (a) with medium class Rigid PVC

141 pipe and accessories (a) 2 wire 1.5 sq. mm Mtr

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded

Copper conductor wire in following type of pipe to be erected

concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for

earth continuity of following size (a) with medium class Rigid PVC

142 pipe and accessories (B) 2 wire 2.5 sq. mm Mtr

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded

Copper conductor wire in following type of pipe to be erected in /

on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of 500.00 106.00

following size. (a) with medium class Rigid PVC pipe and

143 (A) 2 wire 4 sq. mm Mtr

Supplying and erecting approved make double ball bearing

oscillating type Heavy duty bracket fan with Aluminium Blades

A.C. 23OV. 50cy/s wall mounted with height adjustment and

rotary tilting device complete with guard, wall bracket,mounting

144 accessories as directed.

Providing & erecting Approved make Power Saving 50 Watt

Ceiling Fan with double ball bearing ISI mark with Condenser

volt A.C. 50 Hz 1200 mm sweep complete having 3blades with 2.00 1929.00

aluminium blades with , canopy & 30 cm. down rod erected with

145 earthing.(Make shall be approved by Engineer in charge)) Nos

Providing 2.5mm.thick laminated acrylic sheet to cover the fan

146 hook or Fan box. Nos

Supplying and erecting 19 / 20 mm. nominal bore Medium Class

M.S. Pipe down rod erected duly painted for fan complete with 2.00 107.00

147 necessary 24/ O.20, 3 core flexible wire with earthing. Mtr

Supplying & erecting fan hook box of 10 mm M.S. round bar

bounded to the RCC bars up to 50mm length each side and

pierced through a 16 Gauge M.S. box / Heavy Duty PVC box

148 complete erected concealed in Ceiling with necessary finishing. Nos

Supplying & erecting approved make low noise decorative

exhaust fan having square frame ABS body with inbuilt lowers & 2.00 1687.00

149 square frame. 200mm with 1350RPM Cat.II Nos

Supplying and erecting LED indoor fittings with LEDs of wattage

0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing

used as a heat sink shall be made of thick sheet Steel conforming

to IS: 513/CRCA/ aluminium die cast powder coated and high

U.V. & corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.95, THD <

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.). (A) Tube Light with integral driver.

150 (iv) 22-24 Watts, Surge - 2KV,IP-20, conventional 4 feet. Cat-lll EA

Supplying and erecting led lamps with following wattage capacity

of 220 to 240 voltage, minimum 15000 burning hours life, 500 V

in built-surge protection,Polycarbonate diffuser, mounting

suitable for E14 / E27 / B22 lamp holders, pf >= 0.5. (A) LED

Lamps integral type, with PC diffuser suitable LAMP holder. (iii)

151 10 to 15 watts. Cat-III EA

Supplying and erecting LED indoor fittings with LEDs of wattage

0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing

used as a heat sink shall be made of thick sheet Steel conforming

to IS: 513/CRCA/aluminium pressure die cast powder coated and

high U.V. & corrosion resistance with diffuser housed in

aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt , 2.00 584.00

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.). (A) Square/ Circular shaped

Surface/Recessed Mount Downlight with provision for spring

loaded mounting clips complete.IP20. (iii) 16-20 watts, Surge-2

152 KV. Cat-lll EA

Supplying and erecting LED street light / Flood light fittings with

High power White LEDs wattage of 3 Watt and above assembled

on single MCPCB, efficiency more than 130 lm/w and corrosion

free High pressure die cast aluminum housing with smooth finish

powder coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy>

lumens/watt . LED driver efficiency > 85 %.( fittings required LM-

79 & LM-80 certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the ranges shown.). (B)

Flood Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage protection. (iii)

153 Above 60 to 90 watts. Cat-lll EA

DISTRIBUTION BOXES 0.00

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with busbar,

neutral link, earth bar and DIN rail, confirming to IS 13032 and BS

5486-1986 without MCB to house appropriate nos. of MCBs N)

Three phase 6 way SS Double door for horizontal single phase

154 outgoing Ea

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with busbar,

neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 1.00 4620.00

5486-1986 without MCB to house appropriate nos. of MCBs N) (b)

155 sheet steel double door (v) 16 way Ea

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with busbar,

neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC

61439-1 & 3 without MCB to house appropriate nos. of

MCBs.(The DBs should be used of same company of MCB to be

156 used) suitable for

(A) single phase incoming and horizontal single phase outgoing

(b) sheet steel double door (IP-43)

(iii)8 way Ea 1.00 1141.00

(B) three phase incoming and single phase horizontal type

outgoing Per phase isolation type (PPI)

Providing and erecting Sheet Steel powder coated Vertical MCB

distribution board (VTPN) - flush / surface mounted double door

(IP54) fitted with insulated copper busbar, isolated neutral link,

earth bar and DIN rail, confirming to IS 13032 and BS 5486-

1986,IP-54 suitable for 63/100 AMP TPN MCCB + RCCB as

incomer and three phase outgoing as per following .(The DBs

157 should be used of same company of MCB to be used)

(B)6 way outgoing Ea 1.00 12061.00

(D)12 way outgoing Ea 1.00 18480.00

MINIATURE CIRCUIT BREAKER

providing and erecting Miniature circuit breaker single pole

6A to 25A suitable to operate on 240 V A.C. system

and having breaking capacity 10 KA to be erected 75.00 111.00

in existing box. confirming to IS 8828/1996 with ISI

158 Mark Cat.III EA

Providing & erecting 240 V MCB double pole switch for

lighting Load (B Curve) having 10 KA breaking

capacity & confirms to IS : 8828 in existing box

159 having following capacity (B) 40 Amp. Cat.III Ea

Providing & erecting 240 V MCB double pole switch for

motor & inductive load (C Curve) having 10 KA

breaking capacity & confirms to IS : 8828 in existing

160 box having following capacity (A) 6 to 32 Amp. Ea

Providing & erecting 240 V MCB double pole switch for

motor & inductive load (C Curve) having 10 KA

breaking capacity & confirms to IS : 8828 in existing

161 box having following capacity (B) 40 Amp. Ea

Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box 4.00 590.00

having following capacity (a) 6 to 32 Amp.

Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box

163 having following capacity (b)40 Amp. Cat.III Ea

Providing & erecting 415V MCB Four Pole Switch for

Lighting Load (B curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box

164 having following capacity (b)40 Amp. Cat.III Ea

Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box 4.00 730.00

having following capacity

165 C) 63 Amp. CAT-III Ea

Providing & erecting 415 V MCB three Pole for Motor & Inductive

Load (C Curve) having 10KA breaking capacity & confirms to IS 4.00 709.00

166 :8828 in existing box having following capacity Ea

(c)63 Amp. Cat-III

Approved make ELCBs / RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand capacity

of 6 KA and suitable for operation on single phase 240 V. having

characteristic of quick action & tripping with all advance feature

& do not incorporate any electronic component. for following

167 Max. rating erected as directed (i) 25 Amps.DP Cat. III Ea

Approved make ELCBs / RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand capacity

of 6 KA and suitable for operation on single phase 240 V. having

characteristic of quick action & tripping with all advance feature

& do not incorporate any electronic component. for following

168 Max. rating erected as directed (i) 40 Amps.DP Cat. III Ea

Approved make ELCBs / RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand capacity

of 6 KA and suitable for operation on single phase 240 V. having

characteristic of quick action & tripping with all advance feature

& do not incorporate any electronic component. for following

169 Max. rating erected as directed (i) 63 Amps.DP Cat. III Ea

Providing & erecting weather proof, dust & vermin proof, floor

mounted front operated indoor type cubical panel board

necessary IP-42 and above protection as per approval from

engineer incharge made from 14 SWG thick CRC M.S. sheet for

outer body & doors, 16 SWG thick CRC M.S.sheet for internal

partitions with necessary accesories , supporting angles/ flats

channel including cutting, bending, drilling, welding, riveting

with internal partitions & cable alley as per requirements &

instruction of engineer-in-charge with erection of supplied switch

gears, BUSBARS, suitable size of inter connecting PVC copper

wire / copper-aluminium strips, rubber grommets, rib, bakelite 5.00 13442.00

control fuses/MCB for measuring instruments, earth bus & earth

bolts, foundation flange - bolts-base Plates, sufficient nos. of

hinged doors, handles with locking arrangement and rubber

gasket,heavy duty end terminal connection,danger notice

board,necessary ventilation,earthing strip complete. The Panel

shall be painted with epoxy powder coating. (The rates excludes

the cost of switchgears, bus bars, inter connecting mains &

Copper Aluminium strips, meters, Fuses etc. The dimension shall

be measured excluding base beams) The panel shall be supplied

170 with following approved manufacturers with following size.(B) Sq.Mtr

Providing , erecting , fabricating the M.S. structure as per

requirement on site incorporating proper size of M.S.

angles,square,round, flats, bars, channels, sections complete with

cutting, welding, grinding & finishing duly painted with one coat 200.00 77.00

of red oxide with erection on site as per direction of engineer in

charge with necessary grouting, cementing, plastering & finishing

171 complete. kG

Supplying and erecting triple pole & neutral 440V/ 500V panel

mounting Aluminium Busbars with four equal Nos. of bus having

current density not more than 0.8 Amp. / sq.mm (Rated current /

cross section area) duly wrapped with colour insulating tape for

phase sequence of following current carrying capacity, erected

with necessary bus bar supports /insulators, main cable socket to

each busbar,erected in existing cubical panel with necessary

172 connections. (C) Suitable for 300 Amp. Capacity Rn.Mtr

(A) Suitable for 100 Amp. Capacity Rn.Mtr 10.00 654.00

Providing and erecting Approved make Four pole moulded case

circuit breaker having breaking capacity ICU of 35 KA. and above

at 415 V . having normal current rating 250A. with variable

thermal & magnetic release suitable to work on A.C.supply 50 c/s. 1.00 20739.00

with all internal connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing. ICS=100% of ICU

173 only Cat III Ea

Providing and erecting Approved make Four pole moulded case

circuit breaker having breaking capacity ICU of 25 KA. at

V,having normal current rating up to 25 A to 100A. with Fixed

thermal & magnetic release suitable to work on A.C. supply 50 1.00 6112.00

c/s. with all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing. . ICS=100% of

174 ICU only Cat III Ea

Providing and erecting Approved make Four pole moulded case

circuit breaker having breaking capacity ICU of 35 KA. at 415 V.

having normal current rating 125A. with Fixed thermal &

magnetic release suitable to work on A.C.supply 50 c/s. with all 1.00 7976.00

internal connections, spreader tinned copper & complete erected

in existing 16 G.M.S. housing.. . ICS=100% of ICU only Cat

Supplying and erecting led lamps with following wattage capacity

of 220 to 240 voltage, minimum 15000 burning hours life, 500 V

in built-surge protection,Polycarbonate diffuser, mounting

176 suitable for E14 / E27 / B22 lamp holders, pf >=

(A) LED Lamps integral type, with PC diffuser suitable LAMP

(ii) 5 to 8 watts

177 Operational Handle Assembly Complete for

178 Cable Terminal ( ‘Plain" Type)Set of Four for

Supplying & erecting power contactor ,AC3 duty for time switch

179 complete erected as per direction Cat III

Supplying & erecting approved make Digital time switch having

lithium cell 6 years operative and operate battery backup

channel day clock with 14 memory programme, suitable to

operate on 240V + 5%, 16A with, floating contacts Minimum

switching setup time 1 minimum & LCD display. Also comprised

permanent ON/OFF switching. Programming switches & housed

in fire proof thermoplastic enclosure & transparent cover erected

180 as required with necessary connection erected as directed. Ea.

Providing and erecting Approved make Earth fault Relay suitable

to mount with inter connection suitable to following size of

moulded case circuit breaker having CT ratio & MCCB rating as

following along with shunt trip 220V AC. with all internal

181 connections & complete erected in existing M.S.housing..

Providing & erecting Medium Voltage Danger Notice Board

sticker as per language suggested by engineer incharge of 2.00 26.00

182 standard size as per IS-2551 Ea.

providing and erecting Mains with ISI marked, 1.5KV grade

electrolyte multi stranded, annealed copper conductor with heat

resistant PVC insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for control panel,

relays, power switchgears, motor starters & control wiring) with

183 required size of copper lugs, nuts and bolts if required.

(b) One wire 1.50 sq. mm Mtr. 25.00 16.00

(c) One wire 2.50 sq. mm Mtr. 25.00 26.00

providng and erecting Suitable set of CTS for 100A Energy Meter

Supplying and erecting approved make suitable panel indicator

LED type lamp, lens cover, complete erected with necessary 3.00 43.00

185 connections. Ea.

186 TOGGLE SWITCH Ea. 3.00 115.00

187 THERMOSTATE HEATER Ea. 3.00 100.00

Providing and erecting multifunctional meter suitable for

application of Power monitoring and showing measurement of

following Voltage, Frequency, Apparent energy, Apparent power,

Active and reactive energy, Active and reactive power, Average

voltage Vavg, Peak demand power PM, QM, SM, Demand power

P, Q, S, Apparent power S, S1, S2, S3, Unbalance current, Power

factor and displacement PF (signed, four quadrant), Calculated

neutral current, Active, reactive, apparent energy (signed, four 1.00 13984.00

quadrant), Active power P, P1, P2, P3, Voltage U21, U32, U13, V1,

V2, V3, Phase currents, Average current Iag, Peak demand

currents, Reactive power Q, Q1, Q2, Q3, Demand current I1, I2,

I3, [Us] rated supply voltage 40...300 V AC 45...65 Hz, 40...300 V

DC, Network frequency 50 Hz, Type of network 3P, Display type

segments LED, Display colour Red, Messages display capacity

187 fields of 4 characters, Display digits 12 digit(s) - 14.2 mm in height Ea.

Supplying rubber matting of following thickness as per

188 IS:15652/IEC

Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper

189 cable 1.1 KV grade to be erected as directed of following size.

(E) 3 core 2.5 Sq. mm Rmt 50.00 135.00

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Copper conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe at road crossing or

190 floor of following size of cable.

(B) 3 core 4 Sq. mm Rmt 75.00 283.00

(C) 3 core 6 Sq. mm Rmt 75.00 390.00

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following

191 size of cables. (D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core) Rmt

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following

192 size of cables (G) 3 1/2 core 150 Sq. mm ( 70 Sq. mm 1/2 core) Rmt

(F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core) Rmt 100.00 529.00

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following

193 size of cables (B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core) Rmt

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following 175.00 179.00

size of cables.

194 (A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm 1/2 core) Rmt

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following 150.00

size of cables.

195 A)4 core 16 Sq. mm Rmt

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand / Solid Copper conductor for 1.1 KV. to be laid on

wall with necessary clamps or in existing trench / pipe at road

196 crossing or floor of following size of cables. (C) 4 core 6 Sq. mm Rmt

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Copper conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe at road

197 crossing or floor of following size of cables. (A) 4 core 10 Sq. mm Rmt

Providing and, fixing heavy duty flange type brass double

compression type cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails, insulating tape etc

198 for following size of cables. (C) 3 & 1/2 core 70 Sq. mm EA

Providing and, fixing heavy duty flange type brass double

compression type cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails, insulating tape etc

199 for following size of cables. (E) 3 & 1/2 core 120 Sq. mm EA

Providing and, fixing heavy duty flange type brass double

compression type cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails, insulating tape etc

200 for following size of cables. (F) 3 & 1/2 core 150 Sq. mm EA

Providing and, fixing heavy duty flange type brass double

compression type cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails, insulating tape etc

201 for following size of cables. (B) 3 & 1/2 core 35/50 Sq. mm EA

Providing and fixing heavy duty flange type brass cable gland with

rubber ring for PVC insulated armoured cable complete with out

going tails, insulating tape etc for following size of cables.

202 E) 2 to 4 core 25 Sq. mm EA

Providing and fixing heavy duty flange type brass cable gland with

rubber ring for PVC insulated armoured cable complete with out

going tails, insulating tape etc for following size of cables.

203 D) 2 to 4 core 16 Sq. mm Ea

Providing and fixing heavy duty flange type brass cable gland with

rubber ring for PVC insulated armoured cable complete with out

going tails, insulating tape etc for following size of cables.

204 (B) 2 to 4 core 6 Sq. mm Ea

Providing and fixing heavy duty flange type brass cable gland with

rubber ring for PVC insulated armoured cable complete with out

going tails, insulating tape etc for following size of cables.

205 C) 2 to 4 core 10 Sq. mm Ea

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with 10.00 25.00

brass/cadmium plated nut bolts in an approved manner. (E)

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with 10.00 45.00

brass/cadmium plated nut bolts in an approved manner. ((G)

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with 12.00 61.00

brass/cadmium plated nut bolts in an approved manner.(H)

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with 12.00 20.00

brass/cadmium plated nut bolts in an approved manner. (D)

Solderless crimping type Aluminium lugs conforming to IS suitable

for cable of following size evenly crimped with high pressure tool

& connected to switchgear terminals with brass/cadmium plated 50.00 15.00

nut bolts in an approved manner.

Solderless crimping type Aluminium lugs conforming to IS suitable

for cable of following size evenly crimped with high pressure tool

& connected to switchgear terminals with brass/cadmium plated 50.00 13.00

nut bolts in an approved manner.

Solder less crimping type Copper lugs conforming to IS suitable

for cable of following size evenly crimped with high pressure tool

& connected to switchgear terminals with brass/cadmium plated

212 nut bolts in an approved manner. (A) 1.5/2.5 to 6 Sq.mm Ea

Providing and erecting Annealed bare Copper wire 8 to 16 SWG.

Providing and erecting HOT deep Galvanised iron strip wire 8 to

Providing and erecting required size HOT deep Galvanised iron

strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, 75.00 77.00

215 Motors etc. using proper clamp. KG

Providing and erecting required size Copper strip for earthing of

H.T. OCB / ACB/ Transformer, LT panel board, Motors etc. using 30.00 787.00

216 copper clamp. KG

Supplying & erecting in earthpit of minimum bore dia. 225mm

size approved make Safe Earthing Electrode consisting Pipe-in-

Pipe Technology as per IS 3043-1987 made of corrosion free hot

dipped G.I.Pipes having Outer pipe dia of 80 mm having 80-200

Micron galvanising, Inner pipe dia of 40 mm having 200-250

Micron galvanising, connection terminal dia of 14 mm with

constant ohmic value surrounded by highly conductive compound

with high charge dissipation suitable for following type of

applications with chamber and heavy duty cover.(approved

make OEM has to submit test certificate including value of earth

217 resistane of installation.

[B] For Electrical installation up to 11 KV located in other than

normal soil i.e. Soft Rock, Marshy Soil etc.

-Length of Pipe : 2 mtr

-Back filling Compound :1 no. Bag of 25 Kg. Ea

(c) For Electrical Installation covering Transformer Neutrals,

Lightning arrester Earthing, A.C.Plant & Sensitive Computer

System(like Automation, SCADA) i.e independent Earthing in

Length of Pipe : 3.00 mtrs

Back filling Compound :2 nos Bags of 25 Kg. Ea

SITC of 14.2 mm dia 3 mtr long Earth electrode of High tensile

steel electrode with 250 micron copper bonding & 1 bag of

Carbon fill Based environment friendly backfill tested as per IEC

62561-7 in NABL accredited Laboratory and suitable stainless

Steel double sided clamp. Eco Friendly rust proof heavy duty

weather proof Polyethylene Earth Pit Chamber with following

dimensions :254 mm dia (top), 330 mm dia (bottom) & 260 mm

218 (height). Ea

Street Light Pole

Supply of approved make GRP / FRP Pole having following

specifications: GRP Light Pole made by CNC filament winding

machine using thermoset resin polyester/epoxy resin system)

having minimum 62% glass content. The pole should be in one

piece and tapered round in shape, having smooth finish and

should be totally free from corrosion as well as non conductive &

shock proof Pole should be provided with FRP Anchor Base and it

should be heavy duty, or MS Material duly painted with Epoxy

paint. Pole should be flame retardant as per IS 6746. Resin used

shall be UV resistance and pigmented. A highly weather resistant

polyurethane coating shall be applied to the pole after applying

suitable primer system that ensures proper adhesion of the paint.

Minimum coating thickness shall be 80 to 100 micron. Deflection

of the pole shall not exceed more than 10% of the length of pole

for the given load“? Pole should be generally made as per the

dimensional data, performance criteria and some

interchangeability features of poles as per

standard ANSI C 136.20 latest version or ASTM D 4923/01 . The

219 size of pole and type of installation are as below

Supply of approved make FRP Pole having following

specifications: FRP Light Pole made by CNC filament winding

machine using thermoset resin polyester/epoxy resin system)

having minimum 62% glass content. The pole should be in one

piece and tapered round in shape, having smooth finish and

should be totally free from corrosion as well as non conductive &

shock proof Pole should be provided with FRP Anchor Base and

it should be heavy duty, or MS Material duly painted with Epoxy

Pole should be flame retardant as per IS 6746. Resin used shall be

UV resistance and pigmented. A highly weather resistant

polyurethane coating shall be applied to the pole after applying

suitable primer system that ensures proper adhesion of the paint.

Minimum coating thickness shall be 80 to 100 micron. Deflection

of the pole shall not exceed more than 10% of the length of pole

for the given load“ Pole should be generally made as per the

dimensional data, performance criteria and some

interchangeability features of poles as per standard ANSI C

136.20 latest version or ASTM D 4923/01 including cable

termination box with necessary accessories . The size of pole and

type of installation with foundation as per manufacturer details

and site requirement are as below .

(1) Suitable for base plate mounting single arm Bracket.

[H] Overall length of 6 Mtr. Average Thickness: 7.5mm

Top/ Bottom OD Dia A/F 89mm ± 2mm approx. approx. Weight

of Pole 32 kg approx. (Without Base) Anchor Base (Size 300X300

(2) Suitable for base plate mounting Double arm Bracket.

[C] Overall length of 6 Mtr. Average Thickness: 8mm.

Top/ Bottom OD Dia A/F 114/174 mm ± 2mm approx. approx.

Weight of Pole 38 kg approx. (Without Base) Anchor Base (Size

Providing 1:2:4 cement concrete foundation & 70 % PCC from

bottom including excavation for the pole of size 45 x 45 x 100 cm.

Deep in below ground level with plinth of 45 cm x 45 cm (or

cm dia x 45 cm) high upper ground level with necessary curing

and finishing in approved manner.

220 ( for 4 & 6 mtr pole) Ea.

Providing cement concrete.for foundation or for concrete filling

in 1:2:4 ratio with 20 to 25 mm stone metal duly plastered with 20.00 5077.00

221 necessary curing for pole muffing or any other purpose. Cu.Mtr

Providing FRP/GRP arm bracket of having 15˚ arm with 50 mm

OD pipe *5 mm thk,1000mm long from pole centre

(A) Single arm bracket Ea. 15.00 1882.00

(B) Double arm bracket Ea. 5.00 2390.00

Supplying & erecting approved make IP 55 grade Company

fabricated Timer Panel of following capacity for switch On-Off

street lights on time scheduling basis made from 16G CRCA sheet

duly epoxy power painted inside and outside with hinged doors

and locking arrangement consisting of suitable size of 4 Pole MCB

and 4 pole contactor (cat-III)with analog time switch, auto

manual switch of same make and suitable input and output

Bakelite terminals and with door earthing approved by Engineer

Providing & laying approved make Double walled corrugated

pipes (DWC) of polyethylene(conforming to IS 14930 II )with

necessary connecting accessories of same material at required

depth in existing trench for laying of cable. below ground / road

223 surface for enclosing cable

(A)50 mm outer dia Mtr. 300.00 62.00

(B)63mm outer dia Mtr. 200.00 73.00

Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm.

below ground across the road crossing or on floor with necessary

material in an approved manner and making the ground as per

224 original.(C) 300 mm dia Mtr.

Supplying and erecting LED street light / Flood light fittings with

High power White LEDs wattage of 3 Watt and above assembled

on single MCPCB, efficiency more than 130 lm/w and corrosion

free High pressure die cast aluminum housing with smooth finish

powder coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy>

lumens/watt . LED driver efficiency > 85 %.( fittings required LM-

79 & LM-80 certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the ranges shown.). (A)

Street Light (IP-65), Surge protection -4KV integral and ,Light must

have 440VAC line supply with over-voltage protection. (iii) Above

225 60 to 90 watts Each

Supplying and erecting Flexible PVC insulated multi strand multi

core 1.1 kv grade ISI marked copper wires of following size to be

226 erected as directed.

(h) 2.50 Sq.mm 3 core round PVC sheathed Mtr 100.00 73.00

FOOD COMPOSITOR MACHINE CONSIDER 500 KG/HR. CAPACITY

Providing and erecting Approved make Four pole microprocessor

base moulded case circuit breaker having breaking capacity ICU

of 25 KA. at 415 V,having normal current rating up to 25 A to

100A. with Fixed thermal & magnetic release suitable to work on

A.C. supply 50 c/s. with all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S. housing. - (The

Enclosures should be used of same company of MCCBs to be

227 used) -ICS=100% of ICU only Cat III Ea.