Outside painting including tit-bit repair and maintenance of the SLDC Main (old) building and allied works under WBSETCL at SLDC premises, Howrah.

Outside painting including tit-bit repair and maintenance of the SLDC Main (old) building and allied works under WBSETCL at SLDC premises, Howrah.

Percentage BoQ

BoQ_Ver3.0

NIT No.:- CE(O&M)-I/SLDC/2025-26/21 dated 28.01.2026

Bidder Name :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Outside painting including tit-bit repair and maintenance of the SLDC Main (old) building and allied works under WBSETCL at SLDC premises, Howrah.

Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification

Cleaning the exposed reinforcement preferably upto full diameter by wire brush, applying two coats of polymer based rust removing compound left for 24 hours, removing the coating and then applying two (2) coats of polymer modified anti corrosive protective coating formulated to inhibit the corrosion of reinforcement as per manufacturer's specification][Mode of measurement:The affected surface area of reinforcement shall be considered for payment]

Brick work with 1st class bricks in cement mortar (1:4)

(A) In foundation and plinth

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or roughening of concrete surface, including throating, nosing and drip course, scaffolding/staging where necessary. (Excluding cost of chipping over concrete surface). i) With 4:1 cement mortar. In Ground Floor.

(a) 15 mm. thick plaster.

ii) With 4:1 cement mortar. In 1st Floor.

(a) 15 mm. thick plaster.

iii) With 4:1 cement mortar. In 2nd Floor.

(a) 15 mm. thick plaster.

iv) With 4:1 cement mortar. In 3nd Floor.

(a) 15 mm. thick plaster.

Hire and labour charges for shuttering with centering and necessary staging upto 4m using approved stout props and thick hardwood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting fixing and striking out after completion of works (Upto roof of G.floor) a) Steel shuttering or 9 to 12mm thick approved quality ply board shuttering in any concrete work.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups binders etc. initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. a) For works in foundation, basement and upto roof of ground floor/upto 4M i) Tor steel (SAIL/TATA/RINL)

Applying 2 coats of Non-Toxic Acrylic Polymer modified Paint having adhesive & waterproofing properties by mixing in proportion (1 liquid: 4 cementitious material) or as per manufacturer's specification for water proofing layer in water tank etc. (No Departmental Cement is required)

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (i) Pakur Variety

Taking out shutter of door and window, dismantling by parts (for repair or replacement of damaged parts) , reassembling and refitting and rehanging same with old fittings but with new screws as necessary

Easing door and windows

Scraping of moss, blisters etc. thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc.(Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge).

Applying exterior graded acrylic primer of approved quality and brand on plaster or concrete surface to receive decorative texture (mat finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface thoroughly, complete as per manufacturing specification and as per direction of the EIC.

a) One coat

i) In ground floor

ii) In 1-st floor

iii) In 2-nd Floor.

iv) In 3-nd Floor.

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacture’s specification and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.

1) Two coat A) Premium 100% Acrylic Emulsion.

i) In ground floor

ii) In 1-st floor

iii) In 2-nd Floor.

iv) In 3-nd Floor.

Removing loose scales, blisters etc. from old painted surface and thoroughly smoothening the surface to make the same suitable for receiving fresh coat of paint.

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : On steel or other metal surface : With super gloss (hi-gloss) - (iv) Two coats (with any shade except white)

Making one set of scaffolding only for replacing glass panels, painting, uprooting plant and another repairing works of building and S&P works for external works only with 10 cm. dia bamboo as main posts at the rate of 1 metre centre to centre and 7.5 cm. dia bamboo ties @ 0.75 metre apart fitting and fixing with necessary coir, nails etc. as per direction of the Engineer-incharge.

a) 3.90 metre height

b) Extra for additional 3.6 height or part thereof

Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing.

i)Openable steel windows as per IS sizes with side hung shutters and horizotal glazing bars. [The extra rate admissible for the openable portion only]

Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (i) 4 mm thick

Please Enable Macros to View BoQ information